if module doesn't explicitly depend on specific Pci spec, it should include IndustryStandard/Pci.h rather than Pcixxx.h.

Also remove those self-defined "bit(a)" macro, it had been defined as BITx in Base.h.

git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@8994 6f19259b-4bc3-4df7-8a09-765794883524

1 files changed, 34 insertions, 40 deletions

diff --git a/OptionRomPkg/AtapiPassThruDxe/AtapiPassThru.h b/OptionRomPkg/AtapiPassThruDxe/AtapiPassThru.h
index 78501f7f4a..9086dd9bdc 100644
--- a/OptionRomPkg/AtapiPassThruDxe/AtapiPassThru.h
+++ b/OptionRomPkg/AtapiPassThruDxe/AtapiPassThru.h
@@ -34,13 +34,7 @@
 #include <Library/PcdLib.h>

 #include <Library/DevicePathLib.h>

 

-#include <IndustryStandard/Pci22.h>

-

-

-///

-/// bit definition

-///

-#define bit(a)        (1 << (a))

+#include <IndustryStandard/Pci.h>

 

 #define MAX_TARGET_ID 4

 

@@ -212,31 +206,31 @@ typedef struct {
 //

 // ATA Err Reg bitmap

 //

-#define BBK_ERR   bit (7) ///< Bad block detected

-#define UNC_ERR   bit (6) ///< Uncorrectable Data

-#define MC_ERR    bit (5) ///< Media Change

-#define IDNF_ERR  bit (4) ///< ID Not Found

-#define MCR_ERR   bit (3) ///< Media Change Requested

-#define ABRT_ERR  bit (2) ///< Aborted Command

-#define TK0NF_ERR bit (1) ///< Track 0 Not Found

-#define AMNF_ERR  bit (0) ///< Address Mark Not Found

+#define BBK_ERR   BIT7 ///< Bad block detected

+#define UNC_ERR   BIT6 ///< Uncorrectable Data

+#define MC_ERR    BIT5 ///< Media Change

+#define IDNF_ERR  BIT4 ///< ID Not Found

+#define MCR_ERR   BIT3 ///< Media Change Requested

+#define ABRT_ERR  BIT2 ///< Aborted Command

+#define TK0NF_ERR BIT1 ///< Track 0 Not Found

+#define AMNF_ERR  BIT0 ///< Address Mark Not Found

 

 //

 // ATAPI Err Reg bitmap

 //

-#define SENSE_KEY_ERR (bit (7) | bit (6) | bit (5) | bit (4))

-#define EOM_ERR bit (1) ///< End of Media Detected

-#define ILI_ERR bit (0) ///< Illegal Length Indication

+#define SENSE_KEY_ERR (BIT7 | BIT6 | BIT5 | BIT4)

+#define EOM_ERR BIT1 ///< End of Media Detected

+#define ILI_ERR BIT0 ///< Illegal Length Indication

 

 //

 // Device/Head Reg

 //

-#define LBA_MODE  bit (6)

-#define DEV       bit (4)

-#define HS3       bit (3)

-#define HS2       bit (2)

-#define HS1       bit (1)

-#define HS0       bit (0)

+#define LBA_MODE  BIT6

+#define DEV       BIT4

+#define HS3       BIT3

+#define HS2       BIT2

+#define HS1       BIT1

+#define HS0       BIT0

 #define CHS_MODE  (0)

 #define DRV0      (0)

 #define DRV1      (1)

@@ -246,34 +240,34 @@ typedef struct {
 //

 // Status Reg

 //

-#define BSY   bit (7) ///< Controller Busy

-#define DRDY  bit (6) ///< Drive Ready

-#define DWF   bit (5) ///< Drive Write Fault

-#define DSC   bit (4) ///< Disk Seek Complete

-#define DRQ   bit (3) ///< Data Request

-#define CORR  bit (2) ///< Corrected Data

-#define IDX   bit (1) ///< Index

-#define ERR   bit (0) ///< Error

-#define CHECK bit (0) ///< Check bit for ATAPI Status Reg

+#define BSY   BIT7 ///< Controller Busy

+#define DRDY  BIT6 ///< Drive Ready

+#define DWF   BIT5 ///< Drive Write Fault

+#define DSC   BIT4 ///< Disk Seek Complete

+#define DRQ   BIT3 ///< Data Request

+#define CORR  BIT2 ///< Corrected Data

+#define IDX   BIT1 ///< Index

+#define ERR   BIT0 ///< Error

+#define CHECK BIT0 ///< Check bit for ATAPI Status Reg

 

 //

 // Device Control Reg

 //

-#define SRST  bit (2) ///< Software Reset

-#define IEN_L bit (1) ///< Interrupt Enable

+#define SRST  BIT2 ///< Software Reset

+#define IEN_L BIT1 ///< Interrupt Enable

 

 //

 // ATAPI Feature Register

 //

-#define OVERLAP bit (1)

-#define DMA     bit (0)

+#define OVERLAP BIT1

+#define DMA     BIT0

 

 //

 // ATAPI Interrupt Reason Reson Reg (ATA Sector Count Register)

 //

-#define RELEASE     bit (2)

-#define IO          bit (1)

-#define CoD         bit (0)

+#define RELEASE     BIT2

+#define IO          BIT1

+#define CoD         BIT0

 

 #define PACKET_CMD  0xA0