Age | Commit message (Collapse) | Author |
|
On our SynQuacer based platform, power state handling and other
low-level duties are handled by the secure firmware, not by the
OS, so remove the various MHU/SCPI related nodes from the device
tree.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Implement support for the SynQuacer eMMC controller. This involves an
implementation of the SD/MMC override protocol to handle a couple of
quirks that would otherwise prevent this IP from being driven by the
generic SDHCI driver.
Also, add a HII page to the PlatformDxe driver that allows eMMC support
to be enabled, and wire it up for both DeveloperBox and EVB.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Even though the ARM ARM quite clearly states that the CNTFRQ field of
each MMIO timer frame should be a read-only alias of the CNTFRQ field
of the base frame, the SynQuacer SoC implements it as a register that
is programmable separately.
So let's program it from the hardware rather than overriding the
frequency using a DT property.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
The upstream version of the Linux NETSEC driver expects the PHY DT
node to appear under a MDIO subnode, so fix this in the device tree.
Fix the node name as well, this should be 'ethernet' not 'netsec',
and add a clock-names property describing the single clock reference
as 'phy_ref_clk'.
Also, move the PHY subnode into the per-platform .dts file so we can
set the unit address in the node name. This is necessary because recent
versions of the DT compiler are more finicky about this.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Align the UART DT nodes:
- use 'uart' not 'fuart' as node name for the second serial port
- create an alias 'serial1' for the second serial port
- use UART clock reference instead of hardcoded frequency
- split 'clocks' property into 1 cell per phandle
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
In order to be able to use UART #0 on the DeveloperBox's 96boards low
speed connector, expose it to the OS by adding a node to the device
tree. This requires a CM3 firmware build that makes the SCP detach
from the serial port after boot.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Masahisa KOJIMA <kojima.masahisa@socionext.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
It appears that whatever was preventing us from using CPU idle with
PSCI low power states has disappeared, so let's enable the low power
states in the DT.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
As it turns out, it is surprisingly easy to configure both the NETSEC
and eMMC devices as cache coherent for DMA, given that they are both
behind the same SMMU which is already configured in passthrough mode
by the firmware running on the SCP.
So update the static SMMU configuration to make memory accesses performed
by these devices inner shareable inner/outer writeback cacheable, which
makes them cache coherent with the CPUs.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Describe the SynQuacer SoC's eMMC controller in DT so the OS can
attach to it.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Add a DT node for the external interrupt unit (EXIU), which handles
interrupts from GPIO lines. We need OS support for this for things
like PHY interrupts and a 'wake' button.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Add a description of the SoCs GPIO controller as well as a description
of DIP switch block #3, which is wired to GPIOs 0 - 7, both on the
evaluation board as well as the Developer Box.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Add a device tree description of the SynQuacer SoC, and expose it for
the SynQuacerEvalBoard platforms. This includes the menu option in the
UEFI boot menu to switch between ACPI and DT.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|