/** @file
Serial I/O Port library functions with no library constructor/destructor
Copyright (c) 2008 - 2010, Apple Inc. All rights reserved.
Copyright (c) 2011 - 2012, ARM Ltd. All rights reserved.
This program and the accompanying materials
are licensed and made available under the terms and conditions of the BSD License
which accompanies this distribution. The full text of the license may be found at
http://opensource.org/licenses/bsd-license.php
THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
**/
#include
#include
#include
#include
/*
Initialise the serial port to the specified settings.
All unspecified settings will be set to the default values.
@return Always return EFI_SUCCESS or EFI_INVALID_PARAMETER.
**/
RETURN_STATUS
EFIAPI
PL011UartInitializePort (
IN UINTN UartBase,
IN UINT64 BaudRate,
IN UINT32 ReceiveFifoDepth,
IN EFI_PARITY_TYPE Parity,
IN UINT8 DataBits,
IN EFI_STOP_BITS_TYPE StopBits
)
{
UINT32 LineControl;
UINT32 Divisor;
// The BaudRate must be passed
if (BaudRate == 0) {
return RETURN_INVALID_PARAMETER;
}
LineControl = 0;
// The PL011 supports a buffer of either 1 or 32 chars. Therefore we can accept
// 1 char buffer as the minimum fifo size. Because everything can be rounded down,
// there is no maximum fifo size.
if (ReceiveFifoDepth == 0) {
LineControl |= PL011_UARTLCR_H_FEN;
} else if (ReceiveFifoDepth < 32) {
// Nothing else to do. 1 byte fifo is default.
} else if (ReceiveFifoDepth >= 32) {
LineControl |= PL011_UARTLCR_H_FEN;
}
//
// Parity
//
switch (Parity) {
case DefaultParity:
case NoParity:
// Nothing to do. Parity is disabled by default.
break;
case EvenParity:
LineControl |= (PL011_UARTLCR_H_PEN | PL011_UARTLCR_H_EPS);
break;
case OddParity:
LineControl |= PL011_UARTLCR_H_PEN;
break;
case MarkParity:
LineControl |= (PL011_UARTLCR_H_PEN | PL011_UARTLCR_H_SPS | PL011_UARTLCR_H_EPS);
break;
case SpaceParity:
LineControl |= (PL011_UARTLCR_H_PEN | PL011_UARTLCR_H_SPS);
break;
default:
return RETURN_INVALID_PARAMETER;
}
//
// Data Bits
//
switch (DataBits) {
case 0:
case 8:
LineControl |= PL011_UARTLCR_H_WLEN_8;
break;
case 7:
LineControl |= PL011_UARTLCR_H_WLEN_7;
break;
case 6:
LineControl |= PL011_UARTLCR_H_WLEN_6;
break;
case 5:
LineControl |= PL011_UARTLCR_H_WLEN_5;
break;
default:
return RETURN_INVALID_PARAMETER;
}
//
// Stop Bits
//
switch (StopBits) {
case DefaultStopBits:
case OneStopBit:
// Nothing to do. One stop bit is enabled by default.
break;
case TwoStopBits:
LineControl |= PL011_UARTLCR_H_STP2;
break;
case OneFiveStopBits:
// Only 1 or 2 stops bits are supported
default:
return RETURN_INVALID_PARAMETER;
}
// Don't send the LineControl value to the PL011 yet,
// wait until after the Baud Rate setting.
// This ensures we do not mess up the UART settings halfway through
// in the rare case when there is an error with the Baud Rate.
//
// Baud Rate
//
if (PcdGet32(PL011UartInteger) != 0) {
// Integer and Factional part must be different of 0
ASSERT(PcdGet32(PL011UartFractional) != 0);
MmioWrite32 (UartBase + UARTIBRD, PcdGet32(PL011UartInteger));
MmioWrite32 (UartBase + UARTFBRD, PcdGet32(PL011UartFractional));
} else {
Divisor = (PcdGet32 (PL011UartClkInHz) * 4) / BaudRate;
MmioWrite32 (UartBase + UARTIBRD, Divisor >> 6);
MmioWrite32 (UartBase + UARTFBRD, Divisor & 0x3F);
}
// No parity, 1 stop, no fifo, 8 data bits
MmioWrite32 (UartBase + UARTLCR_H, LineControl);
// Clear any pending errors
MmioWrite32 (UartBase + UARTECR, 0);
// Enable tx, rx, and uart overall
MmioWrite32 (UartBase + UARTCR, PL011_UARTCR_RXE | PL011_UARTCR_TXE | PL011_UARTCR_UARTEN);
return RETURN_SUCCESS;
}
/**
Set the serial device control bits.
@param UartBase The base address of the PL011 UART.
@param Control Control bits which are to be set on the serial device.
@retval EFI_SUCCESS The new control bits were set on the serial device.
@retval EFI_UNSUPPORTED The serial device does not support this operation.
@retval EFI_DEVICE_ERROR The serial device is not functioning correctly.
**/
RETURN_STATUS
EFIAPI
PL011UartSetControl (
IN UINTN UartBase,
IN UINT32 Control
)
{
UINT32 Bits;
UINT32 ValidControlBits;
ValidControlBits = ( EFI_SERIAL_REQUEST_TO_SEND
| EFI_SERIAL_DATA_TERMINAL_READY
// | EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE // Not implemented yet.
// | EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE // Not implemented yet.
| EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE
);
if (Control & (~ValidControlBits)) {
return EFI_UNSUPPORTED;
}
Bits = MmioRead32 (UartBase + UARTCR);
if (Control & EFI_SERIAL_REQUEST_TO_SEND) {
Bits |= PL011_UARTCR_RTS;
}
if (Control & EFI_SERIAL_DATA_TERMINAL_READY) {
Bits |= PL011_UARTCR_DTR;
}
if (Control & EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE) {
Bits |= PL011_UARTCR_LBE;
}
if (Control & EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE) {
Bits |= (PL011_UARTCR_CTSEN & PL011_UARTCR_RTSEN);
}
MmioWrite32 (UartBase + UARTCR, Bits);
return RETURN_SUCCESS;
}
/**
Get the serial device control bits.
@param UartBase The base address of the PL011 UART.
@param Control Control signals read from the serial device.
@retval EFI_SUCCESS The control bits were read from the serial device.
@retval EFI_DEVICE_ERROR The serial device is not functioning correctly.
**/
RETURN_STATUS
EFIAPI
PL011UartGetControl (
IN UINTN UartBase,
OUT UINT32 *Control
)
{
UINT32 FlagRegister;
UINT32 ControlRegister;
FlagRegister = MmioRead32 (UartBase + UARTFR);
ControlRegister = MmioRead32 (UartBase + UARTCR);
*Control = 0;
if ((FlagRegister & PL011_UARTFR_CTS) == PL011_UARTFR_CTS) {
*Control |= EFI_SERIAL_CLEAR_TO_SEND;
}
if ((FlagRegister & PL011_UARTFR_DSR) == PL011_UARTFR_DSR) {
*Control |= EFI_SERIAL_DATA_SET_READY;
}
if ((FlagRegister & PL011_UARTFR_RI) == PL011_UARTFR_RI) {
*Control |= EFI_SERIAL_RING_INDICATE;
}
if ((FlagRegister & PL011_UARTFR_DCD) == PL011_UARTFR_DCD) {
*Control |= EFI_SERIAL_CARRIER_DETECT;
}
if ((ControlRegister & PL011_UARTCR_RTS) == PL011_UARTCR_RTS) {
*Control |= EFI_SERIAL_REQUEST_TO_SEND;
}
if ((ControlRegister & PL011_UARTCR_DTR) == PL011_UARTCR_DTR) {
*Control |= EFI_SERIAL_DATA_TERMINAL_READY;
}
if ((FlagRegister & PL011_UARTFR_RXFE) == PL011_UARTFR_RXFE) {
*Control |= EFI_SERIAL_INPUT_BUFFER_EMPTY;
}
if ((FlagRegister & PL011_UARTFR_TXFE) == PL011_UARTFR_TXFE) {
*Control |= EFI_SERIAL_OUTPUT_BUFFER_EMPTY;
}
if ((ControlRegister & (PL011_UARTCR_CTSEN | PL011_UARTCR_RTSEN)) == (PL011_UARTCR_CTSEN | PL011_UARTCR_RTSEN)) {
*Control |= EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE;
}
#ifdef NEVER
// ToDo: Implement EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE
if ((ControlRegister & PL011_UARTCR_LBE) == PL011_UARTCR_LBE) {
*Control |= EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE;
}
// ToDo: Implement EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE
if (SoftwareLoopbackEnable) {
*Control |= EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE;
}
#endif
return RETURN_SUCCESS;
}
/**
Write data to serial device.
@param Buffer Point of data buffer which need to be written.
@param NumberOfBytes Number of output bytes which are cached in Buffer.
@retval 0 Write data failed.
@retval !0 Actual number of bytes written to serial device.
**/
UINTN
EFIAPI
PL011UartWrite (
IN UINTN UartBase,
IN UINT8 *Buffer,
IN UINTN NumberOfBytes
)
{
UINT8* CONST Final = &Buffer[NumberOfBytes];
while (Buffer < Final) {
// Wait until UART able to accept another char
while ((MmioRead32 (UartBase + UARTFR) & UART_TX_FULL_FLAG_MASK));
MmioWrite8 (UartBase + UARTDR, *Buffer);
}
return NumberOfBytes;
}
/**
Read data from serial device and save the data in buffer.
@param Buffer Point of data buffer which need to be written.
@param NumberOfBytes Number of output bytes which are cached in Buffer.
@retval 0 Read data failed.
@retval !0 Actual number of bytes read from serial device.
**/
UINTN
EFIAPI
PL011UartRead (
IN UINTN UartBase,
OUT UINT8 *Buffer,
IN UINTN NumberOfBytes
)
{
UINTN Count;
for (Count = 0; Count < NumberOfBytes; Count++, Buffer++) {
while ((MmioRead32 (UartBase + UARTFR) & UART_RX_EMPTY_FLAG_MASK) != 0);
*Buffer = MmioRead8 (UartBase + UARTDR);
}
return NumberOfBytes;
}
/**
Check to see if any data is available to be read from the debug device.
@retval EFI_SUCCESS At least one byte of data is available to be read
@retval EFI_NOT_READY No data is available to be read
@retval EFI_DEVICE_ERROR The serial device is not functioning properly
**/
BOOLEAN
EFIAPI
PL011UartPoll (
IN UINTN UartBase
)
{
return ((MmioRead32 (UartBase + UARTFR) & UART_RX_EMPTY_FLAG_MASK) == 0);
}