diff options
Diffstat (limited to 'core/include/thirdparties/zlib')
| -rw-r--r-- | core/include/thirdparties/zlib/zconf.h | 1038 | ||||
| -rw-r--r-- | core/include/thirdparties/zlib/zlib.h | 3656 |
2 files changed, 2347 insertions, 2347 deletions
diff --git a/core/include/thirdparties/zlib/zconf.h b/core/include/thirdparties/zlib/zconf.h index 3a1f9696fc..5708a377e0 100644 --- a/core/include/thirdparties/zlib/zconf.h +++ b/core/include/thirdparties/zlib/zconf.h @@ -1,519 +1,519 @@ -/* zconf.h -- configuration of the zlib compression library
- * Copyright (C) 1995-2013 Jean-loup Gailly.
- * For conditions of distribution and use, see copyright notice in zlib.h
- */
-
-/* @(#) $Id$ */
-
-#ifndef ZCONF_H
-#define ZCONF_H
-
-/*
- * If you *really* need a unique prefix for all types and library functions,
- * compile with -DZ_PREFIX. The "standard" zlib should be compiled without it.
- * Even better than compiling with -DZ_PREFIX would be to use configure to set
- * this permanently in zconf.h using "./configure --zprefix".
- */
-#ifdef Z_PREFIX /* may be set to #if 1 by ./configure */
-# define Z_PREFIX_SET
-
-/* all linked symbols */
-# define _dist_code z__dist_code
-# define _length_code z__length_code
-# define _tr_align z__tr_align
-# define _tr_flush_bits z__tr_flush_bits
-# define _tr_flush_block z__tr_flush_block
-# define _tr_init z__tr_init
-# define _tr_stored_block z__tr_stored_block
-# define _tr_tally z__tr_tally
-# define adler32 z_adler32
-# define adler32_combine z_adler32_combine
-# define adler32_combine64 z_adler32_combine64
-# ifndef Z_SOLO
-# define compress z_compress
-# define compress2 z_compress2
-# define compressBound z_compressBound
-# endif
-# define crc32 z_crc32
-# define crc32_combine z_crc32_combine
-# define crc32_combine64 z_crc32_combine64
-# define deflate z_deflate
-# define deflateBound z_deflateBound
-# define deflateCopy z_deflateCopy
-# define deflateEnd z_deflateEnd
-# define deflateInit2_ z_deflateInit2_
-# define deflateInit_ z_deflateInit_
-# define deflateParams z_deflateParams
-# define deflatePending z_deflatePending
-# define deflatePrime z_deflatePrime
-# define deflateReset z_deflateReset
-# define deflateResetKeep z_deflateResetKeep
-# define deflateSetDictionary z_deflateSetDictionary
-# define deflateSetHeader z_deflateSetHeader
-# define deflateTune z_deflateTune
-# define deflate_copyright z_deflate_copyright
-# define get_crc_table z_get_crc_table
-# ifndef Z_SOLO
-# define gz_error z_gz_error
-# define gz_intmax z_gz_intmax
-# define gz_strwinerror z_gz_strwinerror
-# define gzbuffer z_gzbuffer
-# define gzclearerr z_gzclearerr
-# define gzclose z_gzclose
-# define gzclose_r z_gzclose_r
-# define gzclose_w z_gzclose_w
-# define gzdirect z_gzdirect
-# define gzdopen z_gzdopen
-# define gzeof z_gzeof
-# define gzerror z_gzerror
-# define gzflush z_gzflush
-# define gzgetc z_gzgetc
-# define gzgetc_ z_gzgetc_
-# define gzgets z_gzgets
-# define gzoffset z_gzoffset
-# define gzoffset64 z_gzoffset64
-# define gzopen z_gzopen
-# define gzopen64 z_gzopen64
-# ifdef _WIN32
-# define gzopen_w z_gzopen_w
-# endif
-# define gzprintf z_gzprintf
-# define gzvprintf z_gzvprintf
-# define gzputc z_gzputc
-# define gzputs z_gzputs
-# define gzread z_gzread
-# define gzrewind z_gzrewind
-# define gzseek z_gzseek
-# define gzseek64 z_gzseek64
-# define gzsetparams z_gzsetparams
-# define gztell z_gztell
-# define gztell64 z_gztell64
-# define gzungetc z_gzungetc
-# define gzwrite z_gzwrite
-# endif
-# define inflate z_inflate
-# define inflateBack z_inflateBack
-# define inflateBackEnd z_inflateBackEnd
-# define inflateBackInit_ z_inflateBackInit_
-# define inflateCopy z_inflateCopy
-# define inflateEnd z_inflateEnd
-# define inflateGetHeader z_inflateGetHeader
-# define inflateInit2_ z_inflateInit2_
-# define inflateInit_ z_inflateInit_
-# define inflateMark z_inflateMark
-# define inflatePrime z_inflatePrime
-# define inflateReset z_inflateReset
-# define inflateReset2 z_inflateReset2
-# define inflateSetDictionary z_inflateSetDictionary
-# define inflateGetDictionary z_inflateGetDictionary
-# define inflateSync z_inflateSync
-# define inflateSyncPoint z_inflateSyncPoint
-# define inflateUndermine z_inflateUndermine
-# define inflateResetKeep z_inflateResetKeep
-# define inflate_copyright z_inflate_copyright
-# define inflate_fast z_inflate_fast
-# define inflate_table z_inflate_table
-# ifndef Z_SOLO
-# define uncompress z_uncompress
-# endif
-# define zError z_zError
-# ifndef Z_SOLO
-# define zcalloc z_zcalloc
-# define zcfree z_zcfree
-# endif
-# define zlibCompileFlags z_zlibCompileFlags
-# define zlibVersion z_zlibVersion
-
-/* all zlib typedefs in zlib.h and zconf.h */
-# define Byte z_Byte
-# define Bytef z_Bytef
-# define alloc_func z_alloc_func
-# define charf z_charf
-# define free_func z_free_func
-# ifndef Z_SOLO
-# define gzFile z_gzFile
-# endif
-# define gz_header z_gz_header
-# define gz_headerp z_gz_headerp
-# define in_func z_in_func
-# define intf z_intf
-# define out_func z_out_func
-# define uInt z_uInt
-# define uIntf z_uIntf
-# define uLong z_uLong
-# define uLongf z_uLongf
-# define voidp z_voidp
-# define voidpc z_voidpc
-# define voidpf z_voidpf
-
-/* all zlib structs in zlib.h and zconf.h */
-# define gz_header_s z_gz_header_s
-# define internal_state z_internal_state
-
-#endif
-
-#if defined(__MSDOS__) && !defined(MSDOS)
-# define MSDOS
-#endif
-#if (defined(OS_2) || defined(__OS2__)) && !defined(OS2)
-# define OS2
-#endif
-#if defined(_WINDOWS) && !defined(WINDOWS)
-# define WINDOWS
-#endif
-#if defined(_WIN32) || defined(_WIN32_WCE) || defined(__WIN32__)
-# ifndef WIN32
-# define WIN32
-# endif
-#endif
-#if (defined(MSDOS) || defined(OS2) || defined(WINDOWS)) && !defined(WIN32)
-# if !defined(__GNUC__) && !defined(__FLAT__) && !defined(__386__)
-# ifndef SYS16BIT
-# define SYS16BIT
-# endif
-# endif
-#endif
-
-/*
- * Compile with -DMAXSEG_64K if the alloc function cannot allocate more
- * than 64k bytes at a time (needed on systems with 16-bit int).
- */
-#ifdef SYS16BIT
-# define MAXSEG_64K
-#endif
-#ifdef MSDOS
-# define UNALIGNED_OK
-#endif
-
-#ifdef __STDC_VERSION__
-# ifndef STDC
-# define STDC
-# endif
-# if __STDC_VERSION__ >= 199901L
-# ifndef STDC99
-# define STDC99
-# endif
-# endif
-#endif
-#if !defined(STDC) && (defined(__STDC__) || defined(__cplusplus))
-# define STDC
-#endif
-#if !defined(STDC) && (defined(__GNUC__) || defined(__BORLANDC__))
-# define STDC
-#endif
-#if !defined(STDC) && (defined(MSDOS) || defined(WINDOWS) || defined(WIN32))
-# define STDC
-#endif
-#if !defined(STDC) && (defined(OS2) || defined(__HOS_AIX__))
-# define STDC
-#endif
-
-#if defined(__OS400__) && !defined(STDC) /* iSeries (formerly AS/400). */
-# define STDC
-#endif
-
-#ifndef STDC
-# ifndef const /* cannot use !defined(STDC) && !defined(const) on Mac */
-# define const /* note: need a more gentle solution here */
-# endif
-#endif
-
-#if defined(ZLIB_CONST) && !defined(z_const)
-# define z_const const
-#else
-# define z_const
-#endif
-
-/* Some Mac compilers merge all .h files incorrectly: */
-#if defined(__MWERKS__)||defined(applec)||defined(THINK_C)||defined(__SC__)
-# define NO_DUMMY_DECL
-#endif
-
-/* Maximum value for memLevel in deflateInit2 */
-#ifndef MAX_MEM_LEVEL
-# ifdef MAXSEG_64K
-# define MAX_MEM_LEVEL 8
-# else
-# define MAX_MEM_LEVEL 9
-# endif
-#endif
-
-/* Maximum value for windowBits in deflateInit2 and inflateInit2.
- * WARNING: reducing MAX_WBITS makes minigzip unable to extract .gz files
- * created by gzip. (Files created by minigzip can still be extracted by
- * gzip.)
- */
-#ifndef MAX_WBITS
-# define MAX_WBITS 15 /* 32K LZ77 window */
-#endif
-
-/* The memory requirements for deflate are (in bytes):
- (1 << (windowBits+2)) + (1 << (memLevel+9))
- that is: 128K for windowBits=15 + 128K for memLevel = 8 (default values)
- plus a few kilobytes for small objects. For example, if you want to reduce
- the default memory requirements from 256K to 128K, compile with
- make CFLAGS="-O -DMAX_WBITS=14 -DMAX_MEM_LEVEL=7"
- Of course this will generally degrade compression (there's no free lunch).
-
- The memory requirements for inflate are (in bytes) 1 << windowBits
- that is, 32K for windowBits=15 (default value) plus a few kilobytes
- for small objects.
-*/
-
- /* Type declarations */
-
-#ifndef OF /* function prototypes */
-# ifdef STDC
-# define OF(args) args
-# else
-# define OF(args) ()
-# endif
-#endif
-
-#ifndef Z_ARG /* function prototypes for stdarg */
-# if defined(STDC) || defined(Z_HAVE_STDARG_H)
-# define Z_ARG(args) args
-# else
-# define Z_ARG(args) ()
-# endif
-#endif
-
-/* The following definitions for FAR are needed only for MSDOS mixed
- * model programming (small or medium model with some far allocations).
- * This was tested only with MSC; for other MSDOS compilers you may have
- * to define NO_MEMCPY in zutil.h. If you don't need the mixed model,
- * just define FAR to be empty.
- */
-#ifdef SYS16BIT
-# if defined(M_I86SM) || defined(M_I86MM)
- /* MSC small or medium model */
-# define SMALL_MEDIUM
-# ifdef _MSC_VER
-# define FAR _far
-# else
-# define FAR far
-# endif
-# endif
-# if (defined(__SMALL__) || defined(__MEDIUM__))
- /* Turbo C small or medium model */
-# define SMALL_MEDIUM
-# ifdef __BORLANDC__
-# define FAR _far
-# else
-# define FAR far
-# endif
-# endif
-#endif
-
-#if defined(WINDOWS) || defined(WIN32)
- /* If building or using zlib as a DLL, define ZLIB_DLL.
- * This is not mandatory, but it offers a little performance increase.
- */
-# ifdef ZLIB_DLL
-# if defined(WIN32) && (!defined(__BORLANDC__) || (__BORLANDC__ >= 0x500))
-# ifdef ZLIB_INTERNAL
-# define ZEXTERN extern __declspec(dllexport)
-# else
-# define ZEXTERN extern __declspec(dllimport)
-# endif
-# endif
-# endif /* ZLIB_DLL */
- /* If building or using zlib with the WINAPI/WINAPIV calling convention,
- * define ZLIB_WINAPI.
- * Caution: the standard ZLIB1.DLL is NOT compiled using ZLIB_WINAPI.
- */
-# ifdef ZLIB_WINAPI
-# ifdef FAR
-# undef FAR
-# endif
-# include <windows.h>
- /* No need for _export, use ZLIB.DEF instead. */
- /* For complete Windows compatibility, use WINAPI, not __stdcall. */
-# define ZEXPORT WINAPI
-# ifdef WIN32
-# define ZEXPORTVA WINAPIV
-# else
-# define ZEXPORTVA FAR CDECL
-# endif
-# endif
-#endif
-
-#if defined (__BEOS__)
-# ifdef ZLIB_DLL
-# ifdef ZLIB_INTERNAL
-# define ZEXPORT __declspec(dllexport)
-# define ZEXPORTVA __declspec(dllexport)
-# else
-# define ZEXPORT __declspec(dllimport)
-# define ZEXPORTVA __declspec(dllimport)
-# endif
-# endif
-#endif
-
-#ifndef ZEXTERN
-# define ZEXTERN extern
-#endif
-#ifndef ZEXPORT
-# define ZEXPORT
-#endif
-#ifndef ZEXPORTVA
-# define ZEXPORTVA
-#endif
-
-#ifndef FAR
-# define FAR
-#endif
-
-#if !defined(__MACTYPES__)
-typedef unsigned char Byte; /* 8 bits */
-#endif
-typedef unsigned int uInt; /* 16 bits or more */
-typedef unsigned long uLong; /* 32 bits or more */
-
-#ifdef SMALL_MEDIUM
- /* Borland C/C++ and some old MSC versions ignore FAR inside typedef */
-# define Bytef Byte FAR
-#else
- typedef Byte FAR Bytef;
-#endif
-typedef char FAR charf;
-typedef int FAR intf;
-typedef uInt FAR uIntf;
-typedef uLong FAR uLongf;
-
-#ifdef STDC
- typedef void const *voidpc;
- typedef void FAR *voidpf;
- typedef void *voidp;
-#else
- typedef Byte const *voidpc;
- typedef Byte FAR *voidpf;
- typedef Byte *voidp;
-#endif
-
-#if !defined(Z_U4) && !defined(Z_SOLO) && defined(STDC)
-# include <limits.h>
-# if (UINT_MAX == 0xffffffffUL)
-# define Z_U4 unsigned
-# elif (ULONG_MAX == 0xffffffffUL)
-# define Z_U4 unsigned long
-# elif (USHRT_MAX == 0xffffffffUL)
-# define Z_U4 unsigned short
-# endif
-#endif
-
-#ifdef Z_U4
- typedef Z_U4 z_crc_t;
-#else
- typedef unsigned long z_crc_t;
-#endif
-
-#if 0 /* Sunliang.Liu 20100908 sync the config to the old revision, otherwise, evc compile failed. */
-#ifdef HAVE_UNISTD_H /* may be set to #if 1 by ./configure */
-# define Z_HAVE_UNISTD_H
-#endif
-#endif /* 0 */
-
-#ifdef HAVE_STDARG_H /* may be set to #if 1 by ./configure */
-# define Z_HAVE_STDARG_H
-#endif
-
-#if 0 /* Sunliang.Liu 20100908 sync the config to the old revision, otherwise, evc compile failed. */
-#ifdef STDC
-# ifndef Z_SOLO
-# include <sys/types.h> /* for off_t */
-# endif
-#endif
-#endif /* 0 */
-
-#if defined(STDC) || defined(Z_HAVE_STDARG_H)
-# ifndef Z_SOLO
-# include <stdarg.h> /* for va_list */
-# endif
-#endif
-
-#ifdef _WIN32
-# ifndef Z_SOLO
-# include <stddef.h> /* for wchar_t */
-# endif
-#endif
-
-#if 0 /* Sunliang.Liu 20100908 sync the config to the old revision, otherwise, evc compile failed. */
-/* a little trick to accommodate both "#define _LARGEFILE64_SOURCE" and
- * "#define _LARGEFILE64_SOURCE 1" as requesting 64-bit operations, (even
- * though the former does not conform to the LFS document), but considering
- * both "#undef _LARGEFILE64_SOURCE" and "#define _LARGEFILE64_SOURCE 0" as
- * equivalently requesting no 64-bit operations
- */
-#if defined(_LARGEFILE64_SOURCE) && -_LARGEFILE64_SOURCE - -1 == 1
-# undef _LARGEFILE64_SOURCE
-#endif
-#endif /* 0 */
-
-#if defined(__WATCOMC__) && !defined(Z_HAVE_UNISTD_H)
-# define Z_HAVE_UNISTD_H
-#endif
-#ifndef Z_SOLO
-#if 0 /* Sunliang.Liu 20100908 sync the config to the old revision, otherwise, evc compile failed. */
-# if defined(Z_HAVE_UNISTD_H) || defined(_LARGEFILE64_SOURCE)
-# include <unistd.h> /* for SEEK_*, off_t, and _LFS64_LARGEFILE */
-# ifdef VMS
-# include <unixio.h> /* for off_t */
-# endif
-# ifndef z_off_t
-# define z_off_t off_t
-# endif
-# endif
-#endif /* 0 */
-#endif
-
-#if defined(_LFS64_LARGEFILE) && _LFS64_LARGEFILE-0
-# define Z_LFS64
-#endif
-
-#if defined(_LARGEFILE64_SOURCE) && defined(Z_LFS64)
-# define Z_LARGE64
-#endif
-
-#if defined(_FILE_OFFSET_BITS) && _FILE_OFFSET_BITS-0 == 64 && defined(Z_LFS64)
-# define Z_WANT64
-#endif
-
-#if !defined(SEEK_SET) && !defined(Z_SOLO)
-# define SEEK_SET 0 /* Seek from beginning of file. */
-# define SEEK_CUR 1 /* Seek from current position. */
-# define SEEK_END 2 /* Set file pointer to EOF plus "offset" */
-#endif
-
-#ifndef z_off_t
-# define z_off_t long
-#endif
-
-#if !defined(_WIN32) && defined(Z_LARGE64)
-# define z_off64_t off64_t
-#else
-# if defined(_WIN32) && !defined(__GNUC__) && !defined(Z_SOLO)
-# define z_off64_t __int64
-# else
-# define z_off64_t z_off_t
-# endif
-#endif
-
-/* MVS linker does not support external names larger than 8 bytes */
-#if defined(__MVS__)
- #pragma map(deflateInit_,"DEIN")
- #pragma map(deflateInit2_,"DEIN2")
- #pragma map(deflateEnd,"DEEND")
- #pragma map(deflateBound,"DEBND")
- #pragma map(inflateInit_,"ININ")
- #pragma map(inflateInit2_,"ININ2")
- #pragma map(inflateEnd,"INEND")
- #pragma map(inflateSync,"INSY")
- #pragma map(inflateSetDictionary,"INSEDI")
- #pragma map(compressBound,"CMBND")
- #pragma map(inflate_table,"INTABL")
- #pragma map(inflate_fast,"INFA")
- #pragma map(inflate_copyright,"INCOPY")
-#endif
-
-#endif /* ZCONF_H */
+/* zconf.h -- configuration of the zlib compression library + * Copyright (C) 1995-2013 Jean-loup Gailly. + * For conditions of distribution and use, see copyright notice in zlib.h + */ + +/* @(#) $Id$ */ + +#ifndef ZCONF_H +#define ZCONF_H + +/* + * If you *really* need a unique prefix for all types and library functions, + * compile with -DZ_PREFIX. The "standard" zlib should be compiled without it. + * Even better than compiling with -DZ_PREFIX would be to use configure to set + * this permanently in zconf.h using "./configure --zprefix". + */ +#ifdef Z_PREFIX /* may be set to #if 1 by ./configure */ +# define Z_PREFIX_SET + +/* all linked symbols */ +# define _dist_code z__dist_code +# define _length_code z__length_code +# define _tr_align z__tr_align +# define _tr_flush_bits z__tr_flush_bits +# define _tr_flush_block z__tr_flush_block +# define _tr_init z__tr_init +# define _tr_stored_block z__tr_stored_block +# define _tr_tally z__tr_tally +# define adler32 z_adler32 +# define adler32_combine z_adler32_combine +# define adler32_combine64 z_adler32_combine64 +# ifndef Z_SOLO +# define compress z_compress +# define compress2 z_compress2 +# define compressBound z_compressBound +# endif +# define crc32 z_crc32 +# define crc32_combine z_crc32_combine +# define crc32_combine64 z_crc32_combine64 +# define deflate z_deflate +# define deflateBound z_deflateBound +# define deflateCopy z_deflateCopy +# define deflateEnd z_deflateEnd +# define deflateInit2_ z_deflateInit2_ +# define deflateInit_ z_deflateInit_ +# define deflateParams z_deflateParams +# define deflatePending z_deflatePending +# define deflatePrime z_deflatePrime +# define deflateReset z_deflateReset +# define deflateResetKeep z_deflateResetKeep +# define deflateSetDictionary z_deflateSetDictionary +# define deflateSetHeader z_deflateSetHeader +# define deflateTune z_deflateTune +# define deflate_copyright z_deflate_copyright +# define get_crc_table z_get_crc_table +# ifndef Z_SOLO +# define gz_error z_gz_error +# define gz_intmax z_gz_intmax +# define gz_strwinerror z_gz_strwinerror +# define gzbuffer z_gzbuffer +# define gzclearerr z_gzclearerr +# define gzclose z_gzclose +# define gzclose_r z_gzclose_r +# define gzclose_w z_gzclose_w +# define gzdirect z_gzdirect +# define gzdopen z_gzdopen +# define gzeof z_gzeof +# define gzerror z_gzerror +# define gzflush z_gzflush +# define gzgetc z_gzgetc +# define gzgetc_ z_gzgetc_ +# define gzgets z_gzgets +# define gzoffset z_gzoffset +# define gzoffset64 z_gzoffset64 +# define gzopen z_gzopen +# define gzopen64 z_gzopen64 +# ifdef _WIN32 +# define gzopen_w z_gzopen_w +# endif +# define gzprintf z_gzprintf +# define gzvprintf z_gzvprintf +# define gzputc z_gzputc +# define gzputs z_gzputs +# define gzread z_gzread +# define gzrewind z_gzrewind +# define gzseek z_gzseek +# define gzseek64 z_gzseek64 +# define gzsetparams z_gzsetparams +# define gztell z_gztell +# define gztell64 z_gztell64 +# define gzungetc z_gzungetc +# define gzwrite z_gzwrite +# endif +# define inflate z_inflate +# define inflateBack z_inflateBack +# define inflateBackEnd z_inflateBackEnd +# define inflateBackInit_ z_inflateBackInit_ +# define inflateCopy z_inflateCopy +# define inflateEnd z_inflateEnd +# define inflateGetHeader z_inflateGetHeader +# define inflateInit2_ z_inflateInit2_ +# define inflateInit_ z_inflateInit_ +# define inflateMark z_inflateMark +# define inflatePrime z_inflatePrime +# define inflateReset z_inflateReset +# define inflateReset2 z_inflateReset2 +# define inflateSetDictionary z_inflateSetDictionary +# define inflateGetDictionary z_inflateGetDictionary +# define inflateSync z_inflateSync +# define inflateSyncPoint z_inflateSyncPoint +# define inflateUndermine z_inflateUndermine +# define inflateResetKeep z_inflateResetKeep +# define inflate_copyright z_inflate_copyright +# define inflate_fast z_inflate_fast +# define inflate_table z_inflate_table +# ifndef Z_SOLO +# define uncompress z_uncompress +# endif +# define zError z_zError +# ifndef Z_SOLO +# define zcalloc z_zcalloc +# define zcfree z_zcfree +# endif +# define zlibCompileFlags z_zlibCompileFlags +# define zlibVersion z_zlibVersion + +/* all zlib typedefs in zlib.h and zconf.h */ +# define Byte z_Byte +# define Bytef z_Bytef +# define alloc_func z_alloc_func +# define charf z_charf +# define free_func z_free_func +# ifndef Z_SOLO +# define gzFile z_gzFile +# endif +# define gz_header z_gz_header +# define gz_headerp z_gz_headerp +# define in_func z_in_func +# define intf z_intf +# define out_func z_out_func +# define uInt z_uInt +# define uIntf z_uIntf +# define uLong z_uLong +# define uLongf z_uLongf +# define voidp z_voidp +# define voidpc z_voidpc +# define voidpf z_voidpf + +/* all zlib structs in zlib.h and zconf.h */ +# define gz_header_s z_gz_header_s +# define internal_state z_internal_state + +#endif + +#if defined(__MSDOS__) && !defined(MSDOS) +# define MSDOS +#endif +#if (defined(OS_2) || defined(__OS2__)) && !defined(OS2) +# define OS2 +#endif +#if defined(_WINDOWS) && !defined(WINDOWS) +# define WINDOWS +#endif +#if defined(_WIN32) || defined(_WIN32_WCE) || defined(__WIN32__) +# ifndef WIN32 +# define WIN32 +# endif +#endif +#if (defined(MSDOS) || defined(OS2) || defined(WINDOWS)) && !defined(WIN32) +# if !defined(__GNUC__) && !defined(__FLAT__) && !defined(__386__) +# ifndef SYS16BIT +# define SYS16BIT +# endif +# endif +#endif + +/* + * Compile with -DMAXSEG_64K if the alloc function cannot allocate more + * than 64k bytes at a time (needed on systems with 16-bit int). + */ +#ifdef SYS16BIT +# define MAXSEG_64K +#endif +#ifdef MSDOS +# define UNALIGNED_OK +#endif + +#ifdef __STDC_VERSION__ +# ifndef STDC +# define STDC +# endif +# if __STDC_VERSION__ >= 199901L +# ifndef STDC99 +# define STDC99 +# endif +# endif +#endif +#if !defined(STDC) && (defined(__STDC__) || defined(__cplusplus)) +# define STDC +#endif +#if !defined(STDC) && (defined(__GNUC__) || defined(__BORLANDC__)) +# define STDC +#endif +#if !defined(STDC) && (defined(MSDOS) || defined(WINDOWS) || defined(WIN32)) +# define STDC +#endif +#if !defined(STDC) && (defined(OS2) || defined(__HOS_AIX__)) +# define STDC +#endif + +#if defined(__OS400__) && !defined(STDC) /* iSeries (formerly AS/400). */ +# define STDC +#endif + +#ifndef STDC +# ifndef const /* cannot use !defined(STDC) && !defined(const) on Mac */ +# define const /* note: need a more gentle solution here */ +# endif +#endif + +#if defined(ZLIB_CONST) && !defined(z_const) +# define z_const const +#else +# define z_const +#endif + +/* Some Mac compilers merge all .h files incorrectly: */ +#if defined(__MWERKS__)||defined(applec)||defined(THINK_C)||defined(__SC__) +# define NO_DUMMY_DECL +#endif + +/* Maximum value for memLevel in deflateInit2 */ +#ifndef MAX_MEM_LEVEL +# ifdef MAXSEG_64K +# define MAX_MEM_LEVEL 8 +# else +# define MAX_MEM_LEVEL 9 +# endif +#endif + +/* Maximum value for windowBits in deflateInit2 and inflateInit2. + * WARNING: reducing MAX_WBITS makes minigzip unable to extract .gz files + * created by gzip. (Files created by minigzip can still be extracted by + * gzip.) + */ +#ifndef MAX_WBITS +# define MAX_WBITS 15 /* 32K LZ77 window */ +#endif + +/* The memory requirements for deflate are (in bytes): + (1 << (windowBits+2)) + (1 << (memLevel+9)) + that is: 128K for windowBits=15 + 128K for memLevel = 8 (default values) + plus a few kilobytes for small objects. For example, if you want to reduce + the default memory requirements from 256K to 128K, compile with + make CFLAGS="-O -DMAX_WBITS=14 -DMAX_MEM_LEVEL=7" + Of course this will generally degrade compression (there's no free lunch). + + The memory requirements for inflate are (in bytes) 1 << windowBits + that is, 32K for windowBits=15 (default value) plus a few kilobytes + for small objects. +*/ + + /* Type declarations */ + +#ifndef OF /* function prototypes */ +# ifdef STDC +# define OF(args) args +# else +# define OF(args) () +# endif +#endif + +#ifndef Z_ARG /* function prototypes for stdarg */ +# if defined(STDC) || defined(Z_HAVE_STDARG_H) +# define Z_ARG(args) args +# else +# define Z_ARG(args) () +# endif +#endif + +/* The following definitions for FAR are needed only for MSDOS mixed + * model programming (small or medium model with some far allocations). + * This was tested only with MSC; for other MSDOS compilers you may have + * to define NO_MEMCPY in zutil.h. If you don't need the mixed model, + * just define FAR to be empty. + */ +#ifdef SYS16BIT +# if defined(M_I86SM) || defined(M_I86MM) + /* MSC small or medium model */ +# define SMALL_MEDIUM +# ifdef _MSC_VER +# define FAR _far +# else +# define FAR far +# endif +# endif +# if (defined(__SMALL__) || defined(__MEDIUM__)) + /* Turbo C small or medium model */ +# define SMALL_MEDIUM +# ifdef __BORLANDC__ +# define FAR _far +# else +# define FAR far +# endif +# endif +#endif + +#if defined(WINDOWS) || defined(WIN32) + /* If building or using zlib as a DLL, define ZLIB_DLL. + * This is not mandatory, but it offers a little performance increase. + */ +# ifdef ZLIB_DLL +# if defined(WIN32) && (!defined(__BORLANDC__) || (__BORLANDC__ >= 0x500)) +# ifdef ZLIB_INTERNAL +# define ZEXTERN extern __declspec(dllexport) +# else +# define ZEXTERN extern __declspec(dllimport) +# endif +# endif +# endif /* ZLIB_DLL */ + /* If building or using zlib with the WINAPI/WINAPIV calling convention, + * define ZLIB_WINAPI. + * Caution: the standard ZLIB1.DLL is NOT compiled using ZLIB_WINAPI. + */ +# ifdef ZLIB_WINAPI +# ifdef FAR +# undef FAR +# endif +# include <windows.h> + /* No need for _export, use ZLIB.DEF instead. */ + /* For complete Windows compatibility, use WINAPI, not __stdcall. */ +# define ZEXPORT WINAPI +# ifdef WIN32 +# define ZEXPORTVA WINAPIV +# else +# define ZEXPORTVA FAR CDECL +# endif +# endif +#endif + +#if defined (__BEOS__) +# ifdef ZLIB_DLL +# ifdef ZLIB_INTERNAL +# define ZEXPORT __declspec(dllexport) +# define ZEXPORTVA __declspec(dllexport) +# else +# define ZEXPORT __declspec(dllimport) +# define ZEXPORTVA __declspec(dllimport) +# endif +# endif +#endif + +#ifndef ZEXTERN +# define ZEXTERN extern +#endif +#ifndef ZEXPORT +# define ZEXPORT +#endif +#ifndef ZEXPORTVA +# define ZEXPORTVA +#endif + +#ifndef FAR +# define FAR +#endif + +#if !defined(__MACTYPES__) +typedef unsigned char Byte; /* 8 bits */ +#endif +typedef unsigned int uInt; /* 16 bits or more */ +typedef unsigned long uLong; /* 32 bits or more */ + +#ifdef SMALL_MEDIUM + /* Borland C/C++ and some old MSC versions ignore FAR inside typedef */ +# define Bytef Byte FAR +#else + typedef Byte FAR Bytef; +#endif +typedef char FAR charf; +typedef int FAR intf; +typedef uInt FAR uIntf; +typedef uLong FAR uLongf; + +#ifdef STDC + typedef void const *voidpc; + typedef void FAR *voidpf; + typedef void *voidp; +#else + typedef Byte const *voidpc; + typedef Byte FAR *voidpf; + typedef Byte *voidp; +#endif + +#if !defined(Z_U4) && !defined(Z_SOLO) && defined(STDC) +# include <limits.h> +# if (UINT_MAX == 0xffffffffUL) +# define Z_U4 unsigned +# elif (ULONG_MAX == 0xffffffffUL) +# define Z_U4 unsigned long +# elif (USHRT_MAX == 0xffffffffUL) +# define Z_U4 unsigned short +# endif +#endif + +#ifdef Z_U4 + typedef Z_U4 z_crc_t; +#else + typedef unsigned long z_crc_t; +#endif + +#if 0 /* Sunliang.Liu 20100908 sync the config to the old revision, otherwise, evc compile failed. */ +#ifdef HAVE_UNISTD_H /* may be set to #if 1 by ./configure */ +# define Z_HAVE_UNISTD_H +#endif +#endif /* 0 */ + +#ifdef HAVE_STDARG_H /* may be set to #if 1 by ./configure */ +# define Z_HAVE_STDARG_H +#endif + +#if 0 /* Sunliang.Liu 20100908 sync the config to the old revision, otherwise, evc compile failed. */ +#ifdef STDC +# ifndef Z_SOLO +# include <sys/types.h> /* for off_t */ +# endif +#endif +#endif /* 0 */ + +#if defined(STDC) || defined(Z_HAVE_STDARG_H) +# ifndef Z_SOLO +# include <stdarg.h> /* for va_list */ +# endif +#endif + +#ifdef _WIN32 +# ifndef Z_SOLO +# include <stddef.h> /* for wchar_t */ +# endif +#endif + +#if 0 /* Sunliang.Liu 20100908 sync the config to the old revision, otherwise, evc compile failed. */ +/* a little trick to accommodate both "#define _LARGEFILE64_SOURCE" and + * "#define _LARGEFILE64_SOURCE 1" as requesting 64-bit operations, (even + * though the former does not conform to the LFS document), but considering + * both "#undef _LARGEFILE64_SOURCE" and "#define _LARGEFILE64_SOURCE 0" as + * equivalently requesting no 64-bit operations + */ +#if defined(_LARGEFILE64_SOURCE) && -_LARGEFILE64_SOURCE - -1 == 1 +# undef _LARGEFILE64_SOURCE +#endif +#endif /* 0 */ + +#if defined(__WATCOMC__) && !defined(Z_HAVE_UNISTD_H) +# define Z_HAVE_UNISTD_H +#endif +#ifndef Z_SOLO +#if 0 /* Sunliang.Liu 20100908 sync the config to the old revision, otherwise, evc compile failed. */ +# if defined(Z_HAVE_UNISTD_H) || defined(_LARGEFILE64_SOURCE) +# include <unistd.h> /* for SEEK_*, off_t, and _LFS64_LARGEFILE */ +# ifdef VMS +# include <unixio.h> /* for off_t */ +# endif +# ifndef z_off_t +# define z_off_t off_t +# endif +# endif +#endif /* 0 */ +#endif + +#if defined(_LFS64_LARGEFILE) && _LFS64_LARGEFILE-0 +# define Z_LFS64 +#endif + +#if defined(_LARGEFILE64_SOURCE) && defined(Z_LFS64) +# define Z_LARGE64 +#endif + +#if defined(_FILE_OFFSET_BITS) && _FILE_OFFSET_BITS-0 == 64 && defined(Z_LFS64) +# define Z_WANT64 +#endif + +#if !defined(SEEK_SET) && !defined(Z_SOLO) +# define SEEK_SET 0 /* Seek from beginning of file. */ +# define SEEK_CUR 1 /* Seek from current position. */ +# define SEEK_END 2 /* Set file pointer to EOF plus "offset" */ +#endif + +#ifndef z_off_t +# define z_off_t long +#endif + +#if !defined(_WIN32) && defined(Z_LARGE64) +# define z_off64_t off64_t +#else +# if defined(_WIN32) && !defined(__GNUC__) && !defined(Z_SOLO) +# define z_off64_t __int64 +# else +# define z_off64_t z_off_t +# endif +#endif + +/* MVS linker does not support external names larger than 8 bytes */ +#if defined(__MVS__) + #pragma map(deflateInit_,"DEIN") + #pragma map(deflateInit2_,"DEIN2") + #pragma map(deflateEnd,"DEEND") + #pragma map(deflateBound,"DEBND") + #pragma map(inflateInit_,"ININ") + #pragma map(inflateInit2_,"ININ2") + #pragma map(inflateEnd,"INEND") + #pragma map(inflateSync,"INSY") + #pragma map(inflateSetDictionary,"INSEDI") + #pragma map(compressBound,"CMBND") + #pragma map(inflate_table,"INTABL") + #pragma map(inflate_fast,"INFA") + #pragma map(inflate_copyright,"INCOPY") +#endif + +#endif /* ZCONF_H */ diff --git a/core/include/thirdparties/zlib/zlib.h b/core/include/thirdparties/zlib/zlib.h index 5e068c4a37..5850070baf 100644 --- a/core/include/thirdparties/zlib/zlib.h +++ b/core/include/thirdparties/zlib/zlib.h @@ -1,1828 +1,1828 @@ -/* zlib.h -- interface of the 'zlib' general purpose compression library
- version 1.2.8, April 28th, 2013
-
- Copyright (C) 1995-2013 Jean-loup Gailly and Mark Adler
-
- This software is provided 'as-is', without any express or implied
- warranty. In no event will the authors be held liable for any damages
- arising from the use of this software.
-
- Permission is granted to anyone to use this software for any purpose,
- including commercial applications, and to alter it and redistribute it
- freely, subject to the following restrictions:
-
- 1. The origin of this software must not be misrepresented; you must not
- claim that you wrote the original software. If you use this software
- in a product, an acknowledgment in the product documentation would be
- appreciated but is not required.
- 2. Altered source versions must be plainly marked as such, and must not be
- misrepresented as being the original software.
- 3. This notice may not be removed or altered from any source distribution.
-
- Jean-loup Gailly Mark Adler
- jloup@gzip.org madler@alumni.caltech.edu
-
-
- The data format used by the zlib library is described by RFCs (Request for
- Comments) 1950 to 1952 in the files http://tools.ietf.org/html/rfc1950
- (zlib format), rfc1951 (deflate format) and rfc1952 (gzip format).
-*/
-
-#ifndef ZLIB_H
-#define ZLIB_H
-
-#define deflate_copyright FPDFAPI_deflate_copyright
-#define adler32 FPDFAPI_adler32
-#define compress2 FPDFAPI_compress2
-#define compress FPDFAPI_compress
-#define compressBound FPDFAPI_compressBound
-#define get_crc_table FPDFAPI_get_crc_table
-#define crc32 FPDFAPI_crc32
-#define deflateInit_ FPDFAPI_deflateInit_
-#define deflateInit2_ FPDFAPI_deflateInit2_
-#define deflateSetDictionary FPDFAPI_deflateSetDictionary
-#define deflateReset FPDFAPI_deflateReset
-#define deflatePrime FPDFAPI_deflatePrime
-#define deflateParams FPDFAPI_deflateParams
-#define deflateBound FPDFAPI_deflateBound
-#define deflateSetHeader FPDFAPI_deflateSetHeader
-#define deflateTune FPDFAPI_deflateTune
-#define deflate FPDFAPI_deflate
-#define deflateEnd FPDFAPI_deflateEnd
-#define deflateCopy FPDFAPI_deflateCopy
-#define inflateBackInit_ FPDFAPI_inflateBackInit_
-#define inflateBack FPDFAPI_inflateBack
-#define inflateBackEnd FPDFAPI_inflateBackEnd
-#define inflateReset FPDFAPI_inflateReset
-#define inflateInit2_ FPDFAPI_inflateInit2_
-#define inflateInit_ FPDFAPI_inflateInit_
-#define inflate FPDFAPI_inflate
-#define inflateEnd FPDFAPI_inflateEnd
-#define inflateSetDictionary FPDFAPI_inflateSetDictionary
-#define inflateSync FPDFAPI_inflateSync
-#define inflateSyncPoint FPDFAPI_inflateSyncPoint
-#define inflateCopy FPDFAPI_inflateCopy
-#define uncompress FPDFAPI_uncompress
-#define zlibVersion FPDFAPI_zlibVersion
-#define zlibCompileFlags FPDFAPI_zlibCompileFlags
-#define zError FPDFAPI_zError
-#define z_errmsg FPDFAPI_z_errmsg
-#define zcfree FPDFAPI_zcfree
-#define zcalloc FPDFAPI_zcalloc
-#define inflate_fast FPDFAPI_inflate_fast
-#define inflate_table FPDFAPI_inflate_table
-#define inflate_copyright FPDFAPI_inflate_copyright
-#define _length_code FPDFAPI_length_code
-#define _tr_flush_block FPDFAPI_tr_flush_block
-#define _dist_code FPDFAPI_dist_code
-#define _tr_stored_block FPDFAPI_tr_stored_block
-#define _tr_init FPDFAPI_tr_init
-#define _tr_align FPDFAPI_tr_align
-#define _tr_tally FPDFAPI_tr_tally
-#define adler32_combine FPDFAPI_adler32_combine
-#define inflatePrime FPDFAPI_inflatePrime
-#define inflateGetHeader FPDFAPI_inflateGetHeader
-#define crc32_combine FPDFAPI_crc32_combine
-#define inflateReset2 FPDFAPI_inflateReset2
-#define inflateUndermine FPDFAPI_inflateUndermine
-#define inflateMark FPDFAPI_inflateMark
-#define adler32_combine64 FPDFAPI_adler32_combine64
-
-#include "zconf.h"
-
-/* Sunliang.Liu 20100908 sync the config to the old revision. NO_GZIP */
-#define NO_GZIP /* XYQ */
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-#define ZLIB_VERSION "1.2.8"
-#define ZLIB_VERNUM 0x1280
-#define ZLIB_VER_MAJOR 1
-#define ZLIB_VER_MINOR 2
-#define ZLIB_VER_REVISION 8
-#define ZLIB_VER_SUBREVISION 0
-
-/*
- The 'zlib' compression library provides in-memory compression and
- decompression functions, including integrity checks of the uncompressed data.
- This version of the library supports only one compression method (deflation)
- but other algorithms will be added later and will have the same stream
- interface.
-
- Compression can be done in a single step if the buffers are large enough,
- or can be done by repeated calls of the compression function. In the latter
- case, the application must provide more input and/or consume the output
- (providing more output space) before each call.
-
- The compressed data format used by default by the in-memory functions is
- the zlib format, which is a zlib wrapper documented in RFC 1950, wrapped
- around a deflate stream, which is itself documented in RFC 1951.
-
- The library also supports reading and writing files in gzip (.gz) format
- with an interface similar to that of stdio using the functions that start
- with "gz". The gzip format is different from the zlib format. gzip is a
- gzip wrapper, documented in RFC 1952, wrapped around a deflate stream.
-
- This library can optionally read and write gzip streams in memory as well.
-
- The zlib format was designed to be compact and fast for use in memory
- and on communications channels. The gzip format was designed for single-
- file compression on file systems, has a larger header than zlib to maintain
- directory information, and uses a different, slower check method than zlib.
-
- The library does not install any signal handler. The decoder checks
- the consistency of the compressed data, so the library should never crash
- even in case of corrupted input.
-*/
-
-typedef voidpf (*alloc_func) OF((voidpf opaque, uInt items, uInt size));
-typedef void (*free_func) OF((voidpf opaque, voidpf address));
-
-struct internal_state;
-
-typedef struct z_stream_s {
- z_const Bytef *next_in; /* next input byte */
- uInt avail_in; /* number of bytes available at next_in */
- uLong total_in; /* total number of input bytes read so far */
-
- Bytef *next_out; /* next output byte should be put there */
- uInt avail_out; /* remaining free space at next_out */
- uLong total_out; /* total number of bytes output so far */
-
- z_const char *msg; /* last error message, NULL if no error */
- struct internal_state FAR *state; /* not visible by applications */
-
- alloc_func zalloc; /* used to allocate the internal state */
- free_func zfree; /* used to free the internal state */
- voidpf opaque; /* private data object passed to zalloc and zfree */
-
- int data_type; /* best guess about the data type: binary or text */
- uLong adler; /* adler32 value of the uncompressed data */
- uLong reserved; /* reserved for future use */
-} z_stream;
-
-typedef z_stream FAR *z_streamp;
-
-/*
- gzip header information passed to and from zlib routines. See RFC 1952
- for more details on the meanings of these fields.
-*/
-typedef struct gz_header_s {
- int text; /* true if compressed data believed to be text */
- uLong time; /* modification time */
- int xflags; /* extra flags (not used when writing a gzip file) */
- int os; /* operating system */
- Bytef *extra; /* pointer to extra field or Z_NULL if none */
- uInt extra_len; /* extra field length (valid if extra != Z_NULL) */
- uInt extra_max; /* space at extra (only when reading header) */
- Bytef *name; /* pointer to zero-terminated file name or Z_NULL */
- uInt name_max; /* space at name (only when reading header) */
- Bytef *comment; /* pointer to zero-terminated comment or Z_NULL */
- uInt comm_max; /* space at comment (only when reading header) */
- int hcrc; /* true if there was or will be a header crc */
- int done; /* true when done reading gzip header (not used
- when writing a gzip file) */
-} gz_header;
-
-typedef gz_header FAR *gz_headerp;
-
-/*
- The application must update next_in and avail_in when avail_in has dropped
- to zero. It must update next_out and avail_out when avail_out has dropped
- to zero. The application must initialize zalloc, zfree and opaque before
- calling the init function. All other fields are set by the compression
- library and must not be updated by the application.
-
- The opaque value provided by the application will be passed as the first
- parameter for calls of zalloc and zfree. This can be useful for custom
- memory management. The compression library attaches no meaning to the
- opaque value.
-
- zalloc must return Z_NULL if there is not enough memory for the object.
- If zlib is used in a multi-threaded application, zalloc and zfree must be
- thread safe.
-
- On 16-bit systems, the functions zalloc and zfree must be able to allocate
- exactly 65536 bytes, but will not be required to allocate more than this if
- the symbol MAXSEG_64K is defined (see zconf.h). WARNING: On MSDOS, pointers
- returned by zalloc for objects of exactly 65536 bytes *must* have their
- offset normalized to zero. The default allocation function provided by this
- library ensures this (see zutil.c). To reduce memory requirements and avoid
- any allocation of 64K objects, at the expense of compression ratio, compile
- the library with -DMAX_WBITS=14 (see zconf.h).
-
- The fields total_in and total_out can be used for statistics or progress
- reports. After compression, total_in holds the total size of the
- uncompressed data and may be saved for use in the decompressor (particularly
- if the decompressor wants to decompress everything in a single step).
-*/
-
- /* constants */
-
-#define Z_NO_FLUSH 0
-#define Z_PARTIAL_FLUSH 1
-#define Z_SYNC_FLUSH 2
-#define Z_FULL_FLUSH 3
-#define Z_FINISH 4
-#define Z_BLOCK 5
-#define Z_TREES 6
-/* Allowed flush values; see deflate() and inflate() below for details */
-
-#define Z_OK 0
-#define Z_STREAM_END 1
-#define Z_NEED_DICT 2
-#define Z_ERRNO (-1)
-#define Z_STREAM_ERROR (-2)
-#define Z_DATA_ERROR (-3)
-#define Z_MEM_ERROR (-4)
-#define Z_BUF_ERROR (-5)
-#define Z_VERSION_ERROR (-6)
-/* Return codes for the compression/decompression functions. Negative values
- * are errors, positive values are used for special but normal events.
- */
-
-#define Z_NO_COMPRESSION 0
-#define Z_BEST_SPEED 1
-#define Z_BEST_COMPRESSION 9
-#define Z_DEFAULT_COMPRESSION (-1)
-/* compression levels */
-
-#define Z_FILTERED 1
-#define Z_HUFFMAN_ONLY 2
-#define Z_RLE 3
-#define Z_FIXED 4
-#define Z_DEFAULT_STRATEGY 0
-/* compression strategy; see deflateInit2() below for details */
-
-#define Z_BINARY 0
-#define Z_TEXT 1
-#define Z_ASCII Z_TEXT /* for compatibility with 1.2.2 and earlier */
-#define Z_UNKNOWN 2
-/* Possible values of the data_type field (though see inflate()) */
-
-#define Z_DEFLATED 8
-/* The deflate compression method (the only one supported in this version) */
-
-#define Z_NULL 0 /* for initializing zalloc, zfree, opaque */
-
-#define zlib_version zlibVersion()
-/* for compatibility with versions < 1.0.2 */
-
-
- /* basic functions */
-
-ZEXTERN const char * ZEXPORT zlibVersion OF((void));
-/* The application can compare zlibVersion and ZLIB_VERSION for consistency.
- If the first character differs, the library code actually used is not
- compatible with the zlib.h header file used by the application. This check
- is automatically made by deflateInit and inflateInit.
- */
-
-/*
-ZEXTERN int ZEXPORT deflateInit OF((z_streamp strm, int level));
-
- Initializes the internal stream state for compression. The fields
- zalloc, zfree and opaque must be initialized before by the caller. If
- zalloc and zfree are set to Z_NULL, deflateInit updates them to use default
- allocation functions.
-
- The compression level must be Z_DEFAULT_COMPRESSION, or between 0 and 9:
- 1 gives best speed, 9 gives best compression, 0 gives no compression at all
- (the input data is simply copied a block at a time). Z_DEFAULT_COMPRESSION
- requests a default compromise between speed and compression (currently
- equivalent to level 6).
-
- deflateInit returns Z_OK if success, Z_MEM_ERROR if there was not enough
- memory, Z_STREAM_ERROR if level is not a valid compression level, or
- Z_VERSION_ERROR if the zlib library version (zlib_version) is incompatible
- with the version assumed by the caller (ZLIB_VERSION). msg is set to null
- if there is no error message. deflateInit does not perform any compression:
- this will be done by deflate().
-*/
-
-
-ZEXTERN int ZEXPORT deflate OF((z_streamp strm, int flush));
-/*
- deflate compresses as much data as possible, and stops when the input
- buffer becomes empty or the output buffer becomes full. It may introduce
- some output latency (reading input without producing any output) except when
- forced to flush.
-
- The detailed semantics are as follows. deflate performs one or both of the
- following actions:
-
- - Compress more input starting at next_in and update next_in and avail_in
- accordingly. If not all input can be processed (because there is not
- enough room in the output buffer), next_in and avail_in are updated and
- processing will resume at this point for the next call of deflate().
-
- - Provide more output starting at next_out and update next_out and avail_out
- accordingly. This action is forced if the parameter flush is non zero.
- Forcing flush frequently degrades the compression ratio, so this parameter
- should be set only when necessary (in interactive applications). Some
- output may be provided even if flush is not set.
-
- Before the call of deflate(), the application should ensure that at least
- one of the actions is possible, by providing more input and/or consuming more
- output, and updating avail_in or avail_out accordingly; avail_out should
- never be zero before the call. The application can consume the compressed
- output when it wants, for example when the output buffer is full (avail_out
- == 0), or after each call of deflate(). If deflate returns Z_OK and with
- zero avail_out, it must be called again after making room in the output
- buffer because there might be more output pending.
-
- Normally the parameter flush is set to Z_NO_FLUSH, which allows deflate to
- decide how much data to accumulate before producing output, in order to
- maximize compression.
-
- If the parameter flush is set to Z_SYNC_FLUSH, all pending output is
- flushed to the output buffer and the output is aligned on a byte boundary, so
- that the decompressor can get all input data available so far. (In
- particular avail_in is zero after the call if enough output space has been
- provided before the call.) Flushing may degrade compression for some
- compression algorithms and so it should be used only when necessary. This
- completes the current deflate block and follows it with an empty stored block
- that is three bits plus filler bits to the next byte, followed by four bytes
- (00 00 ff ff).
-
- If flush is set to Z_PARTIAL_FLUSH, all pending output is flushed to the
- output buffer, but the output is not aligned to a byte boundary. All of the
- input data so far will be available to the decompressor, as for Z_SYNC_FLUSH.
- This completes the current deflate block and follows it with an empty fixed
- codes block that is 10 bits long. This assures that enough bytes are output
- in order for the decompressor to finish the block before the empty fixed code
- block.
-
- If flush is set to Z_BLOCK, a deflate block is completed and emitted, as
- for Z_SYNC_FLUSH, but the output is not aligned on a byte boundary, and up to
- seven bits of the current block are held to be written as the next byte after
- the next deflate block is completed. In this case, the decompressor may not
- be provided enough bits at this point in order to complete decompression of
- the data provided so far to the compressor. It may need to wait for the next
- block to be emitted. This is for advanced applications that need to control
- the emission of deflate blocks.
-
- If flush is set to Z_FULL_FLUSH, all output is flushed as with
- Z_SYNC_FLUSH, and the compression state is reset so that decompression can
- restart from this point if previous compressed data has been damaged or if
- random access is desired. Using Z_FULL_FLUSH too often can seriously degrade
- compression.
-
- If deflate returns with avail_out == 0, this function must be called again
- with the same value of the flush parameter and more output space (updated
- avail_out), until the flush is complete (deflate returns with non-zero
- avail_out). In the case of a Z_FULL_FLUSH or Z_SYNC_FLUSH, make sure that
- avail_out is greater than six to avoid repeated flush markers due to
- avail_out == 0 on return.
-
- If the parameter flush is set to Z_FINISH, pending input is processed,
- pending output is flushed and deflate returns with Z_STREAM_END if there was
- enough output space; if deflate returns with Z_OK, this function must be
- called again with Z_FINISH and more output space (updated avail_out) but no
- more input data, until it returns with Z_STREAM_END or an error. After
- deflate has returned Z_STREAM_END, the only possible operations on the stream
- are deflateReset or deflateEnd.
-
- Z_FINISH can be used immediately after deflateInit if all the compression
- is to be done in a single step. In this case, avail_out must be at least the
- value returned by deflateBound (see below). Then deflate is guaranteed to
- return Z_STREAM_END. If not enough output space is provided, deflate will
- not return Z_STREAM_END, and it must be called again as described above.
-
- deflate() sets strm->adler to the adler32 checksum of all input read
- so far (that is, total_in bytes).
-
- deflate() may update strm->data_type if it can make a good guess about
- the input data type (Z_BINARY or Z_TEXT). In doubt, the data is considered
- binary. This field is only for information purposes and does not affect the
- compression algorithm in any manner.
-
- deflate() returns Z_OK if some progress has been made (more input
- processed or more output produced), Z_STREAM_END if all input has been
- consumed and all output has been produced (only when flush is set to
- Z_FINISH), Z_STREAM_ERROR if the stream state was inconsistent (for example
- if next_in or next_out was Z_NULL), Z_BUF_ERROR if no progress is possible
- (for example avail_in or avail_out was zero). Note that Z_BUF_ERROR is not
- fatal, and deflate() can be called again with more input and more output
- space to continue compressing.
-*/
-
-
-ZEXTERN int ZEXPORT deflateEnd OF((z_streamp strm));
-/*
- All dynamically allocated data structures for this stream are freed.
- This function discards any unprocessed input and does not flush any pending
- output.
-
- deflateEnd returns Z_OK if success, Z_STREAM_ERROR if the
- stream state was inconsistent, Z_DATA_ERROR if the stream was freed
- prematurely (some input or output was discarded). In the error case, msg
- may be set but then points to a static string (which must not be
- deallocated).
-*/
-
-
-/*
-ZEXTERN int ZEXPORT inflateInit OF((z_streamp strm));
-
- Initializes the internal stream state for decompression. The fields
- next_in, avail_in, zalloc, zfree and opaque must be initialized before by
- the caller. If next_in is not Z_NULL and avail_in is large enough (the
- exact value depends on the compression method), inflateInit determines the
- compression method from the zlib header and allocates all data structures
- accordingly; otherwise the allocation will be deferred to the first call of
- inflate. If zalloc and zfree are set to Z_NULL, inflateInit updates them to
- use default allocation functions.
-
- inflateInit returns Z_OK if success, Z_MEM_ERROR if there was not enough
- memory, Z_VERSION_ERROR if the zlib library version is incompatible with the
- version assumed by the caller, or Z_STREAM_ERROR if the parameters are
- invalid, such as a null pointer to the structure. msg is set to null if
- there is no error message. inflateInit does not perform any decompression
- apart from possibly reading the zlib header if present: actual decompression
- will be done by inflate(). (So next_in and avail_in may be modified, but
- next_out and avail_out are unused and unchanged.) The current implementation
- of inflateInit() does not process any header information -- that is deferred
- until inflate() is called.
-*/
-
-
-ZEXTERN int ZEXPORT inflate OF((z_streamp strm, int flush));
-/*
- inflate decompresses as much data as possible, and stops when the input
- buffer becomes empty or the output buffer becomes full. It may introduce
- some output latency (reading input without producing any output) except when
- forced to flush.
-
- The detailed semantics are as follows. inflate performs one or both of the
- following actions:
-
- - Decompress more input starting at next_in and update next_in and avail_in
- accordingly. If not all input can be processed (because there is not
- enough room in the output buffer), next_in is updated and processing will
- resume at this point for the next call of inflate().
-
- - Provide more output starting at next_out and update next_out and avail_out
- accordingly. inflate() provides as much output as possible, until there is
- no more input data or no more space in the output buffer (see below about
- the flush parameter).
-
- Before the call of inflate(), the application should ensure that at least
- one of the actions is possible, by providing more input and/or consuming more
- output, and updating the next_* and avail_* values accordingly. The
- application can consume the uncompressed output when it wants, for example
- when the output buffer is full (avail_out == 0), or after each call of
- inflate(). If inflate returns Z_OK and with zero avail_out, it must be
- called again after making room in the output buffer because there might be
- more output pending.
-
- The flush parameter of inflate() can be Z_NO_FLUSH, Z_SYNC_FLUSH, Z_FINISH,
- Z_BLOCK, or Z_TREES. Z_SYNC_FLUSH requests that inflate() flush as much
- output as possible to the output buffer. Z_BLOCK requests that inflate()
- stop if and when it gets to the next deflate block boundary. When decoding
- the zlib or gzip format, this will cause inflate() to return immediately
- after the header and before the first block. When doing a raw inflate,
- inflate() will go ahead and process the first block, and will return when it
- gets to the end of that block, or when it runs out of data.
-
- The Z_BLOCK option assists in appending to or combining deflate streams.
- Also to assist in this, on return inflate() will set strm->data_type to the
- number of unused bits in the last byte taken from strm->next_in, plus 64 if
- inflate() is currently decoding the last block in the deflate stream, plus
- 128 if inflate() returned immediately after decoding an end-of-block code or
- decoding the complete header up to just before the first byte of the deflate
- stream. The end-of-block will not be indicated until all of the uncompressed
- data from that block has been written to strm->next_out. The number of
- unused bits may in general be greater than seven, except when bit 7 of
- data_type is set, in which case the number of unused bits will be less than
- eight. data_type is set as noted here every time inflate() returns for all
- flush options, and so can be used to determine the amount of currently
- consumed input in bits.
-
- The Z_TREES option behaves as Z_BLOCK does, but it also returns when the
- end of each deflate block header is reached, before any actual data in that
- block is decoded. This allows the caller to determine the length of the
- deflate block header for later use in random access within a deflate block.
- 256 is added to the value of strm->data_type when inflate() returns
- immediately after reaching the end of the deflate block header.
-
- inflate() should normally be called until it returns Z_STREAM_END or an
- error. However if all decompression is to be performed in a single step (a
- single call of inflate), the parameter flush should be set to Z_FINISH. In
- this case all pending input is processed and all pending output is flushed;
- avail_out must be large enough to hold all of the uncompressed data for the
- operation to complete. (The size of the uncompressed data may have been
- saved by the compressor for this purpose.) The use of Z_FINISH is not
- required to perform an inflation in one step. However it may be used to
- inform inflate that a faster approach can be used for the single inflate()
- call. Z_FINISH also informs inflate to not maintain a sliding window if the
- stream completes, which reduces inflate's memory footprint. If the stream
- does not complete, either because not all of the stream is provided or not
- enough output space is provided, then a sliding window will be allocated and
- inflate() can be called again to continue the operation as if Z_NO_FLUSH had
- been used.
-
- In this implementation, inflate() always flushes as much output as
- possible to the output buffer, and always uses the faster approach on the
- first call. So the effects of the flush parameter in this implementation are
- on the return value of inflate() as noted below, when inflate() returns early
- when Z_BLOCK or Z_TREES is used, and when inflate() avoids the allocation of
- memory for a sliding window when Z_FINISH is used.
-
- If a preset dictionary is needed after this call (see inflateSetDictionary
- below), inflate sets strm->adler to the Adler-32 checksum of the dictionary
- chosen by the compressor and returns Z_NEED_DICT; otherwise it sets
- strm->adler to the Adler-32 checksum of all output produced so far (that is,
- total_out bytes) and returns Z_OK, Z_STREAM_END or an error code as described
- below. At the end of the stream, inflate() checks that its computed adler32
- checksum is equal to that saved by the compressor and returns Z_STREAM_END
- only if the checksum is correct.
-
- inflate() can decompress and check either zlib-wrapped or gzip-wrapped
- deflate data. The header type is detected automatically, if requested when
- initializing with inflateInit2(). Any information contained in the gzip
- header is not retained, so applications that need that information should
- instead use raw inflate, see inflateInit2() below, or inflateBack() and
- perform their own processing of the gzip header and trailer. When processing
- gzip-wrapped deflate data, strm->adler32 is set to the CRC-32 of the output
- producted so far. The CRC-32 is checked against the gzip trailer.
-
- inflate() returns Z_OK if some progress has been made (more input processed
- or more output produced), Z_STREAM_END if the end of the compressed data has
- been reached and all uncompressed output has been produced, Z_NEED_DICT if a
- preset dictionary is needed at this point, Z_DATA_ERROR if the input data was
- corrupted (input stream not conforming to the zlib format or incorrect check
- value), Z_STREAM_ERROR if the stream structure was inconsistent (for example
- next_in or next_out was Z_NULL), Z_MEM_ERROR if there was not enough memory,
- Z_BUF_ERROR if no progress is possible or if there was not enough room in the
- output buffer when Z_FINISH is used. Note that Z_BUF_ERROR is not fatal, and
- inflate() can be called again with more input and more output space to
- continue decompressing. If Z_DATA_ERROR is returned, the application may
- then call inflateSync() to look for a good compression block if a partial
- recovery of the data is desired.
-*/
-
-
-ZEXTERN int ZEXPORT inflateEnd OF((z_streamp strm));
-/*
- All dynamically allocated data structures for this stream are freed.
- This function discards any unprocessed input and does not flush any pending
- output.
-
- inflateEnd returns Z_OK if success, Z_STREAM_ERROR if the stream state
- was inconsistent. In the error case, msg may be set but then points to a
- static string (which must not be deallocated).
-*/
-
-
- /* Advanced functions */
-
-/*
- The following functions are needed only in some special applications.
-*/
-
-/*
-ZEXTERN int ZEXPORT deflateInit2 OF((z_streamp strm,
- int level,
- int method,
- int windowBits,
- int memLevel,
- int strategy));
-
- This is another version of deflateInit with more compression options. The
- fields next_in, zalloc, zfree and opaque must be initialized before by the
- caller.
-
- The method parameter is the compression method. It must be Z_DEFLATED in
- this version of the library.
-
- The windowBits parameter is the base two logarithm of the window size
- (the size of the history buffer). It should be in the range 8..15 for this
- version of the library. Larger values of this parameter result in better
- compression at the expense of memory usage. The default value is 15 if
- deflateInit is used instead.
-
- windowBits can also be -8..-15 for raw deflate. In this case, -windowBits
- determines the window size. deflate() will then generate raw deflate data
- with no zlib header or trailer, and will not compute an adler32 check value.
-
- windowBits can also be greater than 15 for optional gzip encoding. Add
- 16 to windowBits to write a simple gzip header and trailer around the
- compressed data instead of a zlib wrapper. The gzip header will have no
- file name, no extra data, no comment, no modification time (set to zero), no
- header crc, and the operating system will be set to 255 (unknown). If a
- gzip stream is being written, strm->adler is a crc32 instead of an adler32.
-
- The memLevel parameter specifies how much memory should be allocated
- for the internal compression state. memLevel=1 uses minimum memory but is
- slow and reduces compression ratio; memLevel=9 uses maximum memory for
- optimal speed. The default value is 8. See zconf.h for total memory usage
- as a function of windowBits and memLevel.
-
- The strategy parameter is used to tune the compression algorithm. Use the
- value Z_DEFAULT_STRATEGY for normal data, Z_FILTERED for data produced by a
- filter (or predictor), Z_HUFFMAN_ONLY to force Huffman encoding only (no
- string match), or Z_RLE to limit match distances to one (run-length
- encoding). Filtered data consists mostly of small values with a somewhat
- random distribution. In this case, the compression algorithm is tuned to
- compress them better. The effect of Z_FILTERED is to force more Huffman
- coding and less string matching; it is somewhat intermediate between
- Z_DEFAULT_STRATEGY and Z_HUFFMAN_ONLY. Z_RLE is designed to be almost as
- fast as Z_HUFFMAN_ONLY, but give better compression for PNG image data. The
- strategy parameter only affects the compression ratio but not the
- correctness of the compressed output even if it is not set appropriately.
- Z_FIXED prevents the use of dynamic Huffman codes, allowing for a simpler
- decoder for special applications.
-
- deflateInit2 returns Z_OK if success, Z_MEM_ERROR if there was not enough
- memory, Z_STREAM_ERROR if any parameter is invalid (such as an invalid
- method), or Z_VERSION_ERROR if the zlib library version (zlib_version) is
- incompatible with the version assumed by the caller (ZLIB_VERSION). msg is
- set to null if there is no error message. deflateInit2 does not perform any
- compression: this will be done by deflate().
-*/
-
-ZEXTERN int ZEXPORT deflateSetDictionary OF((z_streamp strm,
- const Bytef *dictionary,
- uInt dictLength));
-/*
- Initializes the compression dictionary from the given byte sequence
- without producing any compressed output. When using the zlib format, this
- function must be called immediately after deflateInit, deflateInit2 or
- deflateReset, and before any call of deflate. When doing raw deflate, this
- function must be called either before any call of deflate, or immediately
- after the completion of a deflate block, i.e. after all input has been
- consumed and all output has been delivered when using any of the flush
- options Z_BLOCK, Z_PARTIAL_FLUSH, Z_SYNC_FLUSH, or Z_FULL_FLUSH. The
- compressor and decompressor must use exactly the same dictionary (see
- inflateSetDictionary).
-
- The dictionary should consist of strings (byte sequences) that are likely
- to be encountered later in the data to be compressed, with the most commonly
- used strings preferably put towards the end of the dictionary. Using a
- dictionary is most useful when the data to be compressed is short and can be
- predicted with good accuracy; the data can then be compressed better than
- with the default empty dictionary.
-
- Depending on the size of the compression data structures selected by
- deflateInit or deflateInit2, a part of the dictionary may in effect be
- discarded, for example if the dictionary is larger than the window size
- provided in deflateInit or deflateInit2. Thus the strings most likely to be
- useful should be put at the end of the dictionary, not at the front. In
- addition, the current implementation of deflate will use at most the window
- size minus 262 bytes of the provided dictionary.
-
- Upon return of this function, strm->adler is set to the adler32 value
- of the dictionary; the decompressor may later use this value to determine
- which dictionary has been used by the compressor. (The adler32 value
- applies to the whole dictionary even if only a subset of the dictionary is
- actually used by the compressor.) If a raw deflate was requested, then the
- adler32 value is not computed and strm->adler is not set.
-
- deflateSetDictionary returns Z_OK if success, or Z_STREAM_ERROR if a
- parameter is invalid (e.g. dictionary being Z_NULL) or the stream state is
- inconsistent (for example if deflate has already been called for this stream
- or if not at a block boundary for raw deflate). deflateSetDictionary does
- not perform any compression: this will be done by deflate().
-*/
-
-ZEXTERN int ZEXPORT deflateCopy OF((z_streamp dest,
- z_streamp source));
-/*
- Sets the destination stream as a complete copy of the source stream.
-
- This function can be useful when several compression strategies will be
- tried, for example when there are several ways of pre-processing the input
- data with a filter. The streams that will be discarded should then be freed
- by calling deflateEnd. Note that deflateCopy duplicates the internal
- compression state which can be quite large, so this strategy is slow and can
- consume lots of memory.
-
- deflateCopy returns Z_OK if success, Z_MEM_ERROR if there was not
- enough memory, Z_STREAM_ERROR if the source stream state was inconsistent
- (such as zalloc being Z_NULL). msg is left unchanged in both source and
- destination.
-*/
-
-ZEXTERN int ZEXPORT deflateReset OF((z_streamp strm));
-/*
- This function is equivalent to deflateEnd followed by deflateInit,
- but does not free and reallocate all the internal compression state. The
- stream will keep the same compression level and any other attributes that
- may have been set by deflateInit2.
-
- deflateReset returns Z_OK if success, or Z_STREAM_ERROR if the source
- stream state was inconsistent (such as zalloc or state being Z_NULL).
-*/
-
-ZEXTERN int ZEXPORT deflateParams OF((z_streamp strm,
- int level,
- int strategy));
-/*
- Dynamically update the compression level and compression strategy. The
- interpretation of level and strategy is as in deflateInit2. This can be
- used to switch between compression and straight copy of the input data, or
- to switch to a different kind of input data requiring a different strategy.
- If the compression level is changed, the input available so far is
- compressed with the old level (and may be flushed); the new level will take
- effect only at the next call of deflate().
-
- Before the call of deflateParams, the stream state must be set as for
- a call of deflate(), since the currently available input may have to be
- compressed and flushed. In particular, strm->avail_out must be non-zero.
-
- deflateParams returns Z_OK if success, Z_STREAM_ERROR if the source
- stream state was inconsistent or if a parameter was invalid, Z_BUF_ERROR if
- strm->avail_out was zero.
-*/
-
-ZEXTERN int ZEXPORT deflateTune OF((z_streamp strm,
- int good_length,
- int max_lazy,
- int nice_length,
- int max_chain));
-/*
- Fine tune deflate's internal compression parameters. This should only be
- used by someone who understands the algorithm used by zlib's deflate for
- searching for the best matching string, and even then only by the most
- fanatic optimizer trying to squeeze out the last compressed bit for their
- specific input data. Read the deflate.c source code for the meaning of the
- max_lazy, good_length, nice_length, and max_chain parameters.
-
- deflateTune() can be called after deflateInit() or deflateInit2(), and
- returns Z_OK on success, or Z_STREAM_ERROR for an invalid deflate stream.
- */
-
-ZEXTERN uLong ZEXPORT deflateBound OF((z_streamp strm,
- uLong sourceLen));
-/*
- deflateBound() returns an upper bound on the compressed size after
- deflation of sourceLen bytes. It must be called after deflateInit() or
- deflateInit2(), and after deflateSetHeader(), if used. This would be used
- to allocate an output buffer for deflation in a single pass, and so would be
- called before deflate(). If that first deflate() call is provided the
- sourceLen input bytes, an output buffer allocated to the size returned by
- deflateBound(), and the flush value Z_FINISH, then deflate() is guaranteed
- to return Z_STREAM_END. Note that it is possible for the compressed size to
- be larger than the value returned by deflateBound() if flush options other
- than Z_FINISH or Z_NO_FLUSH are used.
-*/
-
-ZEXTERN int ZEXPORT deflatePending OF((z_streamp strm,
- unsigned *pending,
- int *bits));
-/*
- deflatePending() returns the number of bytes and bits of output that have
- been generated, but not yet provided in the available output. The bytes not
- provided would be due to the available output space having being consumed.
- The number of bits of output not provided are between 0 and 7, where they
- await more bits to join them in order to fill out a full byte. If pending
- or bits are Z_NULL, then those values are not set.
-
- deflatePending returns Z_OK if success, or Z_STREAM_ERROR if the source
- stream state was inconsistent.
- */
-
-ZEXTERN int ZEXPORT deflatePrime OF((z_streamp strm,
- int bits,
- int value));
-/*
- deflatePrime() inserts bits in the deflate output stream. The intent
- is that this function is used to start off the deflate output with the bits
- leftover from a previous deflate stream when appending to it. As such, this
- function can only be used for raw deflate, and must be used before the first
- deflate() call after a deflateInit2() or deflateReset(). bits must be less
- than or equal to 16, and that many of the least significant bits of value
- will be inserted in the output.
-
- deflatePrime returns Z_OK if success, Z_BUF_ERROR if there was not enough
- room in the internal buffer to insert the bits, or Z_STREAM_ERROR if the
- source stream state was inconsistent.
-*/
-
-ZEXTERN int ZEXPORT deflateSetHeader OF((z_streamp strm,
- gz_headerp head));
-/*
- deflateSetHeader() provides gzip header information for when a gzip
- stream is requested by deflateInit2(). deflateSetHeader() may be called
- after deflateInit2() or deflateReset() and before the first call of
- deflate(). The text, time, os, extra field, name, and comment information
- in the provided gz_header structure are written to the gzip header (xflag is
- ignored -- the extra flags are set according to the compression level). The
- caller must assure that, if not Z_NULL, name and comment are terminated with
- a zero byte, and that if extra is not Z_NULL, that extra_len bytes are
- available there. If hcrc is true, a gzip header crc is included. Note that
- the current versions of the command-line version of gzip (up through version
- 1.3.x) do not support header crc's, and will report that it is a "multi-part
- gzip file" and give up.
-
- If deflateSetHeader is not used, the default gzip header has text false,
- the time set to zero, and os set to 255, with no extra, name, or comment
- fields. The gzip header is returned to the default state by deflateReset().
-
- deflateSetHeader returns Z_OK if success, or Z_STREAM_ERROR if the source
- stream state was inconsistent.
-*/
-
-/*
-ZEXTERN int ZEXPORT inflateInit2 OF((z_streamp strm,
- int windowBits));
-
- This is another version of inflateInit with an extra parameter. The
- fields next_in, avail_in, zalloc, zfree and opaque must be initialized
- before by the caller.
-
- The windowBits parameter is the base two logarithm of the maximum window
- size (the size of the history buffer). It should be in the range 8..15 for
- this version of the library. The default value is 15 if inflateInit is used
- instead. windowBits must be greater than or equal to the windowBits value
- provided to deflateInit2() while compressing, or it must be equal to 15 if
- deflateInit2() was not used. If a compressed stream with a larger window
- size is given as input, inflate() will return with the error code
- Z_DATA_ERROR instead of trying to allocate a larger window.
-
- windowBits can also be zero to request that inflate use the window size in
- the zlib header of the compressed stream.
-
- windowBits can also be -8..-15 for raw inflate. In this case, -windowBits
- determines the window size. inflate() will then process raw deflate data,
- not looking for a zlib or gzip header, not generating a check value, and not
- looking for any check values for comparison at the end of the stream. This
- is for use with other formats that use the deflate compressed data format
- such as zip. Those formats provide their own check values. If a custom
- format is developed using the raw deflate format for compressed data, it is
- recommended that a check value such as an adler32 or a crc32 be applied to
- the uncompressed data as is done in the zlib, gzip, and zip formats. For
- most applications, the zlib format should be used as is. Note that comments
- above on the use in deflateInit2() applies to the magnitude of windowBits.
-
- windowBits can also be greater than 15 for optional gzip decoding. Add
- 32 to windowBits to enable zlib and gzip decoding with automatic header
- detection, or add 16 to decode only the gzip format (the zlib format will
- return a Z_DATA_ERROR). If a gzip stream is being decoded, strm->adler is a
- crc32 instead of an adler32.
-
- inflateInit2 returns Z_OK if success, Z_MEM_ERROR if there was not enough
- memory, Z_VERSION_ERROR if the zlib library version is incompatible with the
- version assumed by the caller, or Z_STREAM_ERROR if the parameters are
- invalid, such as a null pointer to the structure. msg is set to null if
- there is no error message. inflateInit2 does not perform any decompression
- apart from possibly reading the zlib header if present: actual decompression
- will be done by inflate(). (So next_in and avail_in may be modified, but
- next_out and avail_out are unused and unchanged.) The current implementation
- of inflateInit2() does not process any header information -- that is
- deferred until inflate() is called.
-*/
-
-ZEXTERN int ZEXPORT inflateSetDictionary OF((z_streamp strm,
- const Bytef *dictionary,
- uInt dictLength));
-/*
- Initializes the decompression dictionary from the given uncompressed byte
- sequence. This function must be called immediately after a call of inflate,
- if that call returned Z_NEED_DICT. The dictionary chosen by the compressor
- can be determined from the adler32 value returned by that call of inflate.
- The compressor and decompressor must use exactly the same dictionary (see
- deflateSetDictionary). For raw inflate, this function can be called at any
- time to set the dictionary. If the provided dictionary is smaller than the
- window and there is already data in the window, then the provided dictionary
- will amend what's there. The application must insure that the dictionary
- that was used for compression is provided.
-
- inflateSetDictionary returns Z_OK if success, Z_STREAM_ERROR if a
- parameter is invalid (e.g. dictionary being Z_NULL) or the stream state is
- inconsistent, Z_DATA_ERROR if the given dictionary doesn't match the
- expected one (incorrect adler32 value). inflateSetDictionary does not
- perform any decompression: this will be done by subsequent calls of
- inflate().
-*/
-
-ZEXTERN int ZEXPORT inflateGetDictionary OF((z_streamp strm,
- Bytef *dictionary,
- uInt *dictLength));
-/*
- Returns the sliding dictionary being maintained by inflate. dictLength is
- set to the number of bytes in the dictionary, and that many bytes are copied
- to dictionary. dictionary must have enough space, where 32768 bytes is
- always enough. If inflateGetDictionary() is called with dictionary equal to
- Z_NULL, then only the dictionary length is returned, and nothing is copied.
- Similary, if dictLength is Z_NULL, then it is not set.
-
- inflateGetDictionary returns Z_OK on success, or Z_STREAM_ERROR if the
- stream state is inconsistent.
-*/
-
-ZEXTERN int ZEXPORT inflateSync OF((z_streamp strm));
-/*
- Skips invalid compressed data until a possible full flush point (see above
- for the description of deflate with Z_FULL_FLUSH) can be found, or until all
- available input is skipped. No output is provided.
-
- inflateSync searches for a 00 00 FF FF pattern in the compressed data.
- All full flush points have this pattern, but not all occurrences of this
- pattern are full flush points.
-
- inflateSync returns Z_OK if a possible full flush point has been found,
- Z_BUF_ERROR if no more input was provided, Z_DATA_ERROR if no flush point
- has been found, or Z_STREAM_ERROR if the stream structure was inconsistent.
- In the success case, the application may save the current current value of
- total_in which indicates where valid compressed data was found. In the
- error case, the application may repeatedly call inflateSync, providing more
- input each time, until success or end of the input data.
-*/
-
-ZEXTERN int ZEXPORT inflateCopy OF((z_streamp dest,
- z_streamp source));
-/*
- Sets the destination stream as a complete copy of the source stream.
-
- This function can be useful when randomly accessing a large stream. The
- first pass through the stream can periodically record the inflate state,
- allowing restarting inflate at those points when randomly accessing the
- stream.
-
- inflateCopy returns Z_OK if success, Z_MEM_ERROR if there was not
- enough memory, Z_STREAM_ERROR if the source stream state was inconsistent
- (such as zalloc being Z_NULL). msg is left unchanged in both source and
- destination.
-*/
-
-ZEXTERN int ZEXPORT inflateReset OF((z_streamp strm));
-/*
- This function is equivalent to inflateEnd followed by inflateInit,
- but does not free and reallocate all the internal decompression state. The
- stream will keep attributes that may have been set by inflateInit2.
-
- inflateReset returns Z_OK if success, or Z_STREAM_ERROR if the source
- stream state was inconsistent (such as zalloc or state being Z_NULL).
-*/
-
-ZEXTERN int ZEXPORT inflateReset2 OF((z_streamp strm,
- int windowBits));
-/*
- This function is the same as inflateReset, but it also permits changing
- the wrap and window size requests. The windowBits parameter is interpreted
- the same as it is for inflateInit2.
-
- inflateReset2 returns Z_OK if success, or Z_STREAM_ERROR if the source
- stream state was inconsistent (such as zalloc or state being Z_NULL), or if
- the windowBits parameter is invalid.
-*/
-
-ZEXTERN int ZEXPORT inflatePrime OF((z_streamp strm,
- int bits,
- int value));
-/*
- This function inserts bits in the inflate input stream. The intent is
- that this function is used to start inflating at a bit position in the
- middle of a byte. The provided bits will be used before any bytes are used
- from next_in. This function should only be used with raw inflate, and
- should be used before the first inflate() call after inflateInit2() or
- inflateReset(). bits must be less than or equal to 16, and that many of the
- least significant bits of value will be inserted in the input.
-
- If bits is negative, then the input stream bit buffer is emptied. Then
- inflatePrime() can be called again to put bits in the buffer. This is used
- to clear out bits leftover after feeding inflate a block description prior
- to feeding inflate codes.
-
- inflatePrime returns Z_OK if success, or Z_STREAM_ERROR if the source
- stream state was inconsistent.
-*/
-
-ZEXTERN long ZEXPORT inflateMark OF((z_streamp strm));
-/*
- This function returns two values, one in the lower 16 bits of the return
- value, and the other in the remaining upper bits, obtained by shifting the
- return value down 16 bits. If the upper value is -1 and the lower value is
- zero, then inflate() is currently decoding information outside of a block.
- If the upper value is -1 and the lower value is non-zero, then inflate is in
- the middle of a stored block, with the lower value equaling the number of
- bytes from the input remaining to copy. If the upper value is not -1, then
- it is the number of bits back from the current bit position in the input of
- the code (literal or length/distance pair) currently being processed. In
- that case the lower value is the number of bytes already emitted for that
- code.
-
- A code is being processed if inflate is waiting for more input to complete
- decoding of the code, or if it has completed decoding but is waiting for
- more output space to write the literal or match data.
-
- inflateMark() is used to mark locations in the input data for random
- access, which may be at bit positions, and to note those cases where the
- output of a code may span boundaries of random access blocks. The current
- location in the input stream can be determined from avail_in and data_type
- as noted in the description for the Z_BLOCK flush parameter for inflate.
-
- inflateMark returns the value noted above or -1 << 16 if the provided
- source stream state was inconsistent.
-*/
-
-ZEXTERN int ZEXPORT inflateGetHeader OF((z_streamp strm,
- gz_headerp head));
-/*
- inflateGetHeader() requests that gzip header information be stored in the
- provided gz_header structure. inflateGetHeader() may be called after
- inflateInit2() or inflateReset(), and before the first call of inflate().
- As inflate() processes the gzip stream, head->done is zero until the header
- is completed, at which time head->done is set to one. If a zlib stream is
- being decoded, then head->done is set to -1 to indicate that there will be
- no gzip header information forthcoming. Note that Z_BLOCK or Z_TREES can be
- used to force inflate() to return immediately after header processing is
- complete and before any actual data is decompressed.
-
- The text, time, xflags, and os fields are filled in with the gzip header
- contents. hcrc is set to true if there is a header CRC. (The header CRC
- was valid if done is set to one.) If extra is not Z_NULL, then extra_max
- contains the maximum number of bytes to write to extra. Once done is true,
- extra_len contains the actual extra field length, and extra contains the
- extra field, or that field truncated if extra_max is less than extra_len.
- If name is not Z_NULL, then up to name_max characters are written there,
- terminated with a zero unless the length is greater than name_max. If
- comment is not Z_NULL, then up to comm_max characters are written there,
- terminated with a zero unless the length is greater than comm_max. When any
- of extra, name, or comment are not Z_NULL and the respective field is not
- present in the header, then that field is set to Z_NULL to signal its
- absence. This allows the use of deflateSetHeader() with the returned
- structure to duplicate the header. However if those fields are set to
- allocated memory, then the application will need to save those pointers
- elsewhere so that they can be eventually freed.
-
- If inflateGetHeader is not used, then the header information is simply
- discarded. The header is always checked for validity, including the header
- CRC if present. inflateReset() will reset the process to discard the header
- information. The application would need to call inflateGetHeader() again to
- retrieve the header from the next gzip stream.
-
- inflateGetHeader returns Z_OK if success, or Z_STREAM_ERROR if the source
- stream state was inconsistent.
-*/
-
-/*
-ZEXTERN int ZEXPORT inflateBackInit OF((z_streamp strm, int windowBits,
- unsigned char FAR *window));
-
- Initialize the internal stream state for decompression using inflateBack()
- calls. The fields zalloc, zfree and opaque in strm must be initialized
- before the call. If zalloc and zfree are Z_NULL, then the default library-
- derived memory allocation routines are used. windowBits is the base two
- logarithm of the window size, in the range 8..15. window is a caller
- supplied buffer of that size. Except for special applications where it is
- assured that deflate was used with small window sizes, windowBits must be 15
- and a 32K byte window must be supplied to be able to decompress general
- deflate streams.
-
- See inflateBack() for the usage of these routines.
-
- inflateBackInit will return Z_OK on success, Z_STREAM_ERROR if any of
- the parameters are invalid, Z_MEM_ERROR if the internal state could not be
- allocated, or Z_VERSION_ERROR if the version of the library does not match
- the version of the header file.
-*/
-
-typedef unsigned (*in_func) OF((void FAR *,
- z_const unsigned char FAR * FAR *));
-typedef int (*out_func) OF((void FAR *, unsigned char FAR *, unsigned));
-
-ZEXTERN int ZEXPORT inflateBack OF((z_streamp strm,
- in_func in, void FAR *in_desc,
- out_func out, void FAR *out_desc));
-/*
- inflateBack() does a raw inflate with a single call using a call-back
- interface for input and output. This is potentially more efficient than
- inflate() for file i/o applications, in that it avoids copying between the
- output and the sliding window by simply making the window itself the output
- buffer. inflate() can be faster on modern CPUs when used with large
- buffers. inflateBack() trusts the application to not change the output
- buffer passed by the output function, at least until inflateBack() returns.
-
- inflateBackInit() must be called first to allocate the internal state
- and to initialize the state with the user-provided window buffer.
- inflateBack() may then be used multiple times to inflate a complete, raw
- deflate stream with each call. inflateBackEnd() is then called to free the
- allocated state.
-
- A raw deflate stream is one with no zlib or gzip header or trailer.
- This routine would normally be used in a utility that reads zip or gzip
- files and writes out uncompressed files. The utility would decode the
- header and process the trailer on its own, hence this routine expects only
- the raw deflate stream to decompress. This is different from the normal
- behavior of inflate(), which expects either a zlib or gzip header and
- trailer around the deflate stream.
-
- inflateBack() uses two subroutines supplied by the caller that are then
- called by inflateBack() for input and output. inflateBack() calls those
- routines until it reads a complete deflate stream and writes out all of the
- uncompressed data, or until it encounters an error. The function's
- parameters and return types are defined above in the in_func and out_func
- typedefs. inflateBack() will call in(in_desc, &buf) which should return the
- number of bytes of provided input, and a pointer to that input in buf. If
- there is no input available, in() must return zero--buf is ignored in that
- case--and inflateBack() will return a buffer error. inflateBack() will call
- out(out_desc, buf, len) to write the uncompressed data buf[0..len-1]. out()
- should return zero on success, or non-zero on failure. If out() returns
- non-zero, inflateBack() will return with an error. Neither in() nor out()
- are permitted to change the contents of the window provided to
- inflateBackInit(), which is also the buffer that out() uses to write from.
- The length written by out() will be at most the window size. Any non-zero
- amount of input may be provided by in().
-
- For convenience, inflateBack() can be provided input on the first call by
- setting strm->next_in and strm->avail_in. If that input is exhausted, then
- in() will be called. Therefore strm->next_in must be initialized before
- calling inflateBack(). If strm->next_in is Z_NULL, then in() will be called
- immediately for input. If strm->next_in is not Z_NULL, then strm->avail_in
- must also be initialized, and then if strm->avail_in is not zero, input will
- initially be taken from strm->next_in[0 .. strm->avail_in - 1].
-
- The in_desc and out_desc parameters of inflateBack() is passed as the
- first parameter of in() and out() respectively when they are called. These
- descriptors can be optionally used to pass any information that the caller-
- supplied in() and out() functions need to do their job.
-
- On return, inflateBack() will set strm->next_in and strm->avail_in to
- pass back any unused input that was provided by the last in() call. The
- return values of inflateBack() can be Z_STREAM_END on success, Z_BUF_ERROR
- if in() or out() returned an error, Z_DATA_ERROR if there was a format error
- in the deflate stream (in which case strm->msg is set to indicate the nature
- of the error), or Z_STREAM_ERROR if the stream was not properly initialized.
- In the case of Z_BUF_ERROR, an input or output error can be distinguished
- using strm->next_in which will be Z_NULL only if in() returned an error. If
- strm->next_in is not Z_NULL, then the Z_BUF_ERROR was due to out() returning
- non-zero. (in() will always be called before out(), so strm->next_in is
- assured to be defined if out() returns non-zero.) Note that inflateBack()
- cannot return Z_OK.
-*/
-
-ZEXTERN int ZEXPORT inflateBackEnd OF((z_streamp strm));
-/*
- All memory allocated by inflateBackInit() is freed.
-
- inflateBackEnd() returns Z_OK on success, or Z_STREAM_ERROR if the stream
- state was inconsistent.
-*/
-
-ZEXTERN uLong ZEXPORT zlibCompileFlags OF((void));
-/* Return flags indicating compile-time options.
-
- Type sizes, two bits each, 00 = 16 bits, 01 = 32, 10 = 64, 11 = other:
- 1.0: size of uInt
- 3.2: size of uLong
- 5.4: size of voidpf (pointer)
- 7.6: size of z_off_t
-
- Compiler, assembler, and debug options:
- 8: DEBUG
- 9: ASMV or ASMINF -- use ASM code
- 10: ZLIB_WINAPI -- exported functions use the WINAPI calling convention
- 11: 0 (reserved)
-
- One-time table building (smaller code, but not thread-safe if true):
- 12: BUILDFIXED -- build static block decoding tables when needed
- 13: DYNAMIC_CRC_TABLE -- build CRC calculation tables when needed
- 14,15: 0 (reserved)
-
- Library content (indicates missing functionality):
- 16: NO_GZCOMPRESS -- gz* functions cannot compress (to avoid linking
- deflate code when not needed)
- 17: NO_GZIP -- deflate can't write gzip streams, and inflate can't detect
- and decode gzip streams (to avoid linking crc code)
- 18-19: 0 (reserved)
-
- Operation variations (changes in library functionality):
- 20: PKZIP_BUG_WORKAROUND -- slightly more permissive inflate
- 21: FASTEST -- deflate algorithm with only one, lowest compression level
- 22,23: 0 (reserved)
-
- The sprintf variant used by gzprintf (zero is best):
- 24: 0 = vs*, 1 = s* -- 1 means limited to 20 arguments after the format
- 25: 0 = *nprintf, 1 = *printf -- 1 means gzprintf() not secure!
- 26: 0 = returns value, 1 = void -- 1 means inferred string length returned
-
- Remainder:
- 27-31: 0 (reserved)
- */
-
-#ifndef Z_SOLO
-
- /* utility functions */
-
-/*
- The following utility functions are implemented on top of the basic
- stream-oriented functions. To simplify the interface, some default options
- are assumed (compression level and memory usage, standard memory allocation
- functions). The source code of these utility functions can be modified if
- you need special options.
-*/
-
-ZEXTERN int ZEXPORT compress OF((Bytef *dest, uLongf *destLen,
- const Bytef *source, uLong sourceLen));
-/*
- Compresses the source buffer into the destination buffer. sourceLen is
- the byte length of the source buffer. Upon entry, destLen is the total size
- of the destination buffer, which must be at least the value returned by
- compressBound(sourceLen). Upon exit, destLen is the actual size of the
- compressed buffer.
-
- compress returns Z_OK if success, Z_MEM_ERROR if there was not
- enough memory, Z_BUF_ERROR if there was not enough room in the output
- buffer.
-*/
-
-ZEXTERN int ZEXPORT compress2 OF((Bytef *dest, uLongf *destLen,
- const Bytef *source, uLong sourceLen,
- int level));
-/*
- Compresses the source buffer into the destination buffer. The level
- parameter has the same meaning as in deflateInit. sourceLen is the byte
- length of the source buffer. Upon entry, destLen is the total size of the
- destination buffer, which must be at least the value returned by
- compressBound(sourceLen). Upon exit, destLen is the actual size of the
- compressed buffer.
-
- compress2 returns Z_OK if success, Z_MEM_ERROR if there was not enough
- memory, Z_BUF_ERROR if there was not enough room in the output buffer,
- Z_STREAM_ERROR if the level parameter is invalid.
-*/
-
-ZEXTERN uLong ZEXPORT compressBound OF((uLong sourceLen));
-/*
- compressBound() returns an upper bound on the compressed size after
- compress() or compress2() on sourceLen bytes. It would be used before a
- compress() or compress2() call to allocate the destination buffer.
-*/
-
-ZEXTERN int ZEXPORT uncompress OF((Bytef *dest, uLongf *destLen,
- const Bytef *source, uLong sourceLen));
-/*
- Decompresses the source buffer into the destination buffer. sourceLen is
- the byte length of the source buffer. Upon entry, destLen is the total size
- of the destination buffer, which must be large enough to hold the entire
- uncompressed data. (The size of the uncompressed data must have been saved
- previously by the compressor and transmitted to the decompressor by some
- mechanism outside the scope of this compression library.) Upon exit, destLen
- is the actual size of the uncompressed buffer.
-
- uncompress returns Z_OK if success, Z_MEM_ERROR if there was not
- enough memory, Z_BUF_ERROR if there was not enough room in the output
- buffer, or Z_DATA_ERROR if the input data was corrupted or incomplete. In
- the case where there is not enough room, uncompress() will fill the output
- buffer with the uncompressed data up to that point.
-*/
-
- /* gzip file access functions */
-
-/*
- This library supports reading and writing files in gzip (.gz) format with
- an interface similar to that of stdio, using the functions that start with
- "gz". The gzip format is different from the zlib format. gzip is a gzip
- wrapper, documented in RFC 1952, wrapped around a deflate stream.
-*/
-
-typedef struct gzFile_s *gzFile; /* semi-opaque gzip file descriptor */
-
-/*
-ZEXTERN gzFile ZEXPORT gzopen OF((const char *path, const char *mode));
-
- Opens a gzip (.gz) file for reading or writing. The mode parameter is as
- in fopen ("rb" or "wb") but can also include a compression level ("wb9") or
- a strategy: 'f' for filtered data as in "wb6f", 'h' for Huffman-only
- compression as in "wb1h", 'R' for run-length encoding as in "wb1R", or 'F'
- for fixed code compression as in "wb9F". (See the description of
- deflateInit2 for more information about the strategy parameter.) 'T' will
- request transparent writing or appending with no compression and not using
- the gzip format.
-
- "a" can be used instead of "w" to request that the gzip stream that will
- be written be appended to the file. "+" will result in an error, since
- reading and writing to the same gzip file is not supported. The addition of
- "x" when writing will create the file exclusively, which fails if the file
- already exists. On systems that support it, the addition of "e" when
- reading or writing will set the flag to close the file on an execve() call.
-
- These functions, as well as gzip, will read and decode a sequence of gzip
- streams in a file. The append function of gzopen() can be used to create
- such a file. (Also see gzflush() for another way to do this.) When
- appending, gzopen does not test whether the file begins with a gzip stream,
- nor does it look for the end of the gzip streams to begin appending. gzopen
- will simply append a gzip stream to the existing file.
-
- gzopen can be used to read a file which is not in gzip format; in this
- case gzread will directly read from the file without decompression. When
- reading, this will be detected automatically by looking for the magic two-
- byte gzip header.
-
- gzopen returns NULL if the file could not be opened, if there was
- insufficient memory to allocate the gzFile state, or if an invalid mode was
- specified (an 'r', 'w', or 'a' was not provided, or '+' was provided).
- errno can be checked to determine if the reason gzopen failed was that the
- file could not be opened.
-*/
-
-ZEXTERN gzFile ZEXPORT gzdopen OF((int fd, const char *mode));
-/*
- gzdopen associates a gzFile with the file descriptor fd. File descriptors
- are obtained from calls like open, dup, creat, pipe or fileno (if the file
- has been previously opened with fopen). The mode parameter is as in gzopen.
-
- The next call of gzclose on the returned gzFile will also close the file
- descriptor fd, just like fclose(fdopen(fd, mode)) closes the file descriptor
- fd. If you want to keep fd open, use fd = dup(fd_keep); gz = gzdopen(fd,
- mode);. The duplicated descriptor should be saved to avoid a leak, since
- gzdopen does not close fd if it fails. If you are using fileno() to get the
- file descriptor from a FILE *, then you will have to use dup() to avoid
- double-close()ing the file descriptor. Both gzclose() and fclose() will
- close the associated file descriptor, so they need to have different file
- descriptors.
-
- gzdopen returns NULL if there was insufficient memory to allocate the
- gzFile state, if an invalid mode was specified (an 'r', 'w', or 'a' was not
- provided, or '+' was provided), or if fd is -1. The file descriptor is not
- used until the next gz* read, write, seek, or close operation, so gzdopen
- will not detect if fd is invalid (unless fd is -1).
-*/
-
-ZEXTERN int ZEXPORT gzbuffer OF((gzFile file, unsigned size));
-/*
- Set the internal buffer size used by this library's functions. The
- default buffer size is 8192 bytes. This function must be called after
- gzopen() or gzdopen(), and before any other calls that read or write the
- file. The buffer memory allocation is always deferred to the first read or
- write. Two buffers are allocated, either both of the specified size when
- writing, or one of the specified size and the other twice that size when
- reading. A larger buffer size of, for example, 64K or 128K bytes will
- noticeably increase the speed of decompression (reading).
-
- The new buffer size also affects the maximum length for gzprintf().
-
- gzbuffer() returns 0 on success, or -1 on failure, such as being called
- too late.
-*/
-
-ZEXTERN int ZEXPORT gzsetparams OF((gzFile file, int level, int strategy));
-/*
- Dynamically update the compression level or strategy. See the description
- of deflateInit2 for the meaning of these parameters.
-
- gzsetparams returns Z_OK if success, or Z_STREAM_ERROR if the file was not
- opened for writing.
-*/
-
-ZEXTERN int ZEXPORT gzread OF((gzFile file, voidp buf, unsigned len));
-/*
- Reads the given number of uncompressed bytes from the compressed file. If
- the input file is not in gzip format, gzread copies the given number of
- bytes into the buffer directly from the file.
-
- After reaching the end of a gzip stream in the input, gzread will continue
- to read, looking for another gzip stream. Any number of gzip streams may be
- concatenated in the input file, and will all be decompressed by gzread().
- If something other than a gzip stream is encountered after a gzip stream,
- that remaining trailing garbage is ignored (and no error is returned).
-
- gzread can be used to read a gzip file that is being concurrently written.
- Upon reaching the end of the input, gzread will return with the available
- data. If the error code returned by gzerror is Z_OK or Z_BUF_ERROR, then
- gzclearerr can be used to clear the end of file indicator in order to permit
- gzread to be tried again. Z_OK indicates that a gzip stream was completed
- on the last gzread. Z_BUF_ERROR indicates that the input file ended in the
- middle of a gzip stream. Note that gzread does not return -1 in the event
- of an incomplete gzip stream. This error is deferred until gzclose(), which
- will return Z_BUF_ERROR if the last gzread ended in the middle of a gzip
- stream. Alternatively, gzerror can be used before gzclose to detect this
- case.
-
- gzread returns the number of uncompressed bytes actually read, less than
- len for end of file, or -1 for error.
-*/
-
-ZEXTERN int ZEXPORT gzwrite OF((gzFile file,
- voidpc buf, unsigned len));
-/*
- Writes the given number of uncompressed bytes into the compressed file.
- gzwrite returns the number of uncompressed bytes written or 0 in case of
- error.
-*/
-
-ZEXTERN int ZEXPORTVA gzprintf Z_ARG((gzFile file, const char *format, ...));
-/*
- Converts, formats, and writes the arguments to the compressed file under
- control of the format string, as in fprintf. gzprintf returns the number of
- uncompressed bytes actually written, or 0 in case of error. The number of
- uncompressed bytes written is limited to 8191, or one less than the buffer
- size given to gzbuffer(). The caller should assure that this limit is not
- exceeded. If it is exceeded, then gzprintf() will return an error (0) with
- nothing written. In this case, there may also be a buffer overflow with
- unpredictable consequences, which is possible only if zlib was compiled with
- the insecure functions sprintf() or vsprintf() because the secure snprintf()
- or vsnprintf() functions were not available. This can be determined using
- zlibCompileFlags().
-*/
-
-ZEXTERN int ZEXPORT gzputs OF((gzFile file, const char *s));
-/*
- Writes the given null-terminated string to the compressed file, excluding
- the terminating null character.
-
- gzputs returns the number of characters written, or -1 in case of error.
-*/
-
-ZEXTERN char * ZEXPORT gzgets OF((gzFile file, char *buf, int len));
-/*
- Reads bytes from the compressed file until len-1 characters are read, or a
- newline character is read and transferred to buf, or an end-of-file
- condition is encountered. If any characters are read or if len == 1, the
- string is terminated with a null character. If no characters are read due
- to an end-of-file or len < 1, then the buffer is left untouched.
-
- gzgets returns buf which is a null-terminated string, or it returns NULL
- for end-of-file or in case of error. If there was an error, the contents at
- buf are indeterminate.
-*/
-
-ZEXTERN int ZEXPORT gzputc OF((gzFile file, int c));
-/*
- Writes c, converted to an unsigned char, into the compressed file. gzputc
- returns the value that was written, or -1 in case of error.
-*/
-
-ZEXTERN int ZEXPORT gzgetc OF((gzFile file));
-/*
- Reads one byte from the compressed file. gzgetc returns this byte or -1
- in case of end of file or error. This is implemented as a macro for speed.
- As such, it does not do all of the checking the other functions do. I.e.
- it does not check to see if file is NULL, nor whether the structure file
- points to has been clobbered or not.
-*/
-
-ZEXTERN int ZEXPORT gzungetc OF((int c, gzFile file));
-/*
- Push one character back onto the stream to be read as the first character
- on the next read. At least one character of push-back is allowed.
- gzungetc() returns the character pushed, or -1 on failure. gzungetc() will
- fail if c is -1, and may fail if a character has been pushed but not read
- yet. If gzungetc is used immediately after gzopen or gzdopen, at least the
- output buffer size of pushed characters is allowed. (See gzbuffer above.)
- The pushed character will be discarded if the stream is repositioned with
- gzseek() or gzrewind().
-*/
-
-ZEXTERN int ZEXPORT gzflush OF((gzFile file, int flush));
-/*
- Flushes all pending output into the compressed file. The parameter flush
- is as in the deflate() function. The return value is the zlib error number
- (see function gzerror below). gzflush is only permitted when writing.
-
- If the flush parameter is Z_FINISH, the remaining data is written and the
- gzip stream is completed in the output. If gzwrite() is called again, a new
- gzip stream will be started in the output. gzread() is able to read such
- concatented gzip streams.
-
- gzflush should be called only when strictly necessary because it will
- degrade compression if called too often.
-*/
-
-/*
-ZEXTERN z_off_t ZEXPORT gzseek OF((gzFile file,
- z_off_t offset, int whence));
-
- Sets the starting position for the next gzread or gzwrite on the given
- compressed file. The offset represents a number of bytes in the
- uncompressed data stream. The whence parameter is defined as in lseek(2);
- the value SEEK_END is not supported.
-
- If the file is opened for reading, this function is emulated but can be
- extremely slow. If the file is opened for writing, only forward seeks are
- supported; gzseek then compresses a sequence of zeroes up to the new
- starting position.
-
- gzseek returns the resulting offset location as measured in bytes from
- the beginning of the uncompressed stream, or -1 in case of error, in
- particular if the file is opened for writing and the new starting position
- would be before the current position.
-*/
-
-ZEXTERN int ZEXPORT gzrewind OF((gzFile file));
-/*
- Rewinds the given file. This function is supported only for reading.
-
- gzrewind(file) is equivalent to (int)gzseek(file, 0L, SEEK_SET)
-*/
-
-/*
-ZEXTERN z_off_t ZEXPORT gztell OF((gzFile file));
-
- Returns the starting position for the next gzread or gzwrite on the given
- compressed file. This position represents a number of bytes in the
- uncompressed data stream, and is zero when starting, even if appending or
- reading a gzip stream from the middle of a file using gzdopen().
-
- gztell(file) is equivalent to gzseek(file, 0L, SEEK_CUR)
-*/
-
-/*
-ZEXTERN z_off_t ZEXPORT gzoffset OF((gzFile file));
-
- Returns the current offset in the file being read or written. This offset
- includes the count of bytes that precede the gzip stream, for example when
- appending or when using gzdopen() for reading. When reading, the offset
- does not include as yet unused buffered input. This information can be used
- for a progress indicator. On error, gzoffset() returns -1.
-*/
-
-ZEXTERN int ZEXPORT gzeof OF((gzFile file));
-/*
- Returns true (1) if the end-of-file indicator has been set while reading,
- false (0) otherwise. Note that the end-of-file indicator is set only if the
- read tried to go past the end of the input, but came up short. Therefore,
- just like feof(), gzeof() may return false even if there is no more data to
- read, in the event that the last read request was for the exact number of
- bytes remaining in the input file. This will happen if the input file size
- is an exact multiple of the buffer size.
-
- If gzeof() returns true, then the read functions will return no more data,
- unless the end-of-file indicator is reset by gzclearerr() and the input file
- has grown since the previous end of file was detected.
-*/
-
-ZEXTERN int ZEXPORT gzdirect OF((gzFile file));
-/*
- Returns true (1) if file is being copied directly while reading, or false
- (0) if file is a gzip stream being decompressed.
-
- If the input file is empty, gzdirect() will return true, since the input
- does not contain a gzip stream.
-
- If gzdirect() is used immediately after gzopen() or gzdopen() it will
- cause buffers to be allocated to allow reading the file to determine if it
- is a gzip file. Therefore if gzbuffer() is used, it should be called before
- gzdirect().
-
- When writing, gzdirect() returns true (1) if transparent writing was
- requested ("wT" for the gzopen() mode), or false (0) otherwise. (Note:
- gzdirect() is not needed when writing. Transparent writing must be
- explicitly requested, so the application already knows the answer. When
- linking statically, using gzdirect() will include all of the zlib code for
- gzip file reading and decompression, which may not be desired.)
-*/
-
-ZEXTERN int ZEXPORT gzclose OF((gzFile file));
-/*
- Flushes all pending output if necessary, closes the compressed file and
- deallocates the (de)compression state. Note that once file is closed, you
- cannot call gzerror with file, since its structures have been deallocated.
- gzclose must not be called more than once on the same file, just as free
- must not be called more than once on the same allocation.
-
- gzclose will return Z_STREAM_ERROR if file is not valid, Z_ERRNO on a
- file operation error, Z_MEM_ERROR if out of memory, Z_BUF_ERROR if the
- last read ended in the middle of a gzip stream, or Z_OK on success.
-*/
-
-ZEXTERN int ZEXPORT gzclose_r OF((gzFile file));
-ZEXTERN int ZEXPORT gzclose_w OF((gzFile file));
-/*
- Same as gzclose(), but gzclose_r() is only for use when reading, and
- gzclose_w() is only for use when writing or appending. The advantage to
- using these instead of gzclose() is that they avoid linking in zlib
- compression or decompression code that is not used when only reading or only
- writing respectively. If gzclose() is used, then both compression and
- decompression code will be included the application when linking to a static
- zlib library.
-*/
-
-ZEXTERN const char * ZEXPORT gzerror OF((gzFile file, int *errnum));
-/*
- Returns the error message for the last error which occurred on the given
- compressed file. errnum is set to zlib error number. If an error occurred
- in the file system and not in the compression library, errnum is set to
- Z_ERRNO and the application may consult errno to get the exact error code.
-
- The application must not modify the returned string. Future calls to
- this function may invalidate the previously returned string. If file is
- closed, then the string previously returned by gzerror will no longer be
- available.
-
- gzerror() should be used to distinguish errors from end-of-file for those
- functions above that do not distinguish those cases in their return values.
-*/
-
-ZEXTERN void ZEXPORT gzclearerr OF((gzFile file));
-/*
- Clears the error and end-of-file flags for file. This is analogous to the
- clearerr() function in stdio. This is useful for continuing to read a gzip
- file that is being written concurrently.
-*/
-
-#endif /* !Z_SOLO */
-
- /* checksum functions */
-
-/*
- These functions are not related to compression but are exported
- anyway because they might be useful in applications using the compression
- library.
-*/
-
-ZEXTERN uLong ZEXPORT adler32 OF((uLong adler, const Bytef *buf, uInt len));
-/*
- Update a running Adler-32 checksum with the bytes buf[0..len-1] and
- return the updated checksum. If buf is Z_NULL, this function returns the
- required initial value for the checksum.
-
- An Adler-32 checksum is almost as reliable as a CRC32 but can be computed
- much faster.
-
- Usage example:
-
- uLong adler = adler32(0L, Z_NULL, 0);
-
- while (read_buffer(buffer, length) != EOF) {
- adler = adler32(adler, buffer, length);
- }
- if (adler != original_adler) error();
-*/
-
-/*
-ZEXTERN uLong ZEXPORT adler32_combine OF((uLong adler1, uLong adler2,
- z_off_t len2));
-
- Combine two Adler-32 checksums into one. For two sequences of bytes, seq1
- and seq2 with lengths len1 and len2, Adler-32 checksums were calculated for
- each, adler1 and adler2. adler32_combine() returns the Adler-32 checksum of
- seq1 and seq2 concatenated, requiring only adler1, adler2, and len2. Note
- that the z_off_t type (like off_t) is a signed integer. If len2 is
- negative, the result has no meaning or utility.
-*/
-
-ZEXTERN uLong ZEXPORT crc32 OF((uLong crc, const Bytef *buf, uInt len));
-/*
- Update a running CRC-32 with the bytes buf[0..len-1] and return the
- updated CRC-32. If buf is Z_NULL, this function returns the required
- initial value for the crc. Pre- and post-conditioning (one's complement) is
- performed within this function so it shouldn't be done by the application.
-
- Usage example:
-
- uLong crc = crc32(0L, Z_NULL, 0);
-
- while (read_buffer(buffer, length) != EOF) {
- crc = crc32(crc, buffer, length);
- }
- if (crc != original_crc) error();
-*/
-
-/*
-ZEXTERN uLong ZEXPORT crc32_combine OF((uLong crc1, uLong crc2, z_off_t len2));
-
- Combine two CRC-32 check values into one. For two sequences of bytes,
- seq1 and seq2 with lengths len1 and len2, CRC-32 check values were
- calculated for each, crc1 and crc2. crc32_combine() returns the CRC-32
- check value of seq1 and seq2 concatenated, requiring only crc1, crc2, and
- len2.
-*/
-
-
- /* various hacks, don't look :) */
-
-/* deflateInit and inflateInit are macros to allow checking the zlib version
- * and the compiler's view of z_stream:
- */
-ZEXTERN int ZEXPORT deflateInit_ OF((z_streamp strm, int level,
- const char *version, int stream_size));
-ZEXTERN int ZEXPORT inflateInit_ OF((z_streamp strm,
- const char *version, int stream_size));
-ZEXTERN int ZEXPORT deflateInit2_ OF((z_streamp strm, int level, int method,
- int windowBits, int memLevel,
- int strategy, const char *version,
- int stream_size));
-ZEXTERN int ZEXPORT inflateInit2_ OF((z_streamp strm, int windowBits,
- const char *version, int stream_size));
-ZEXTERN int ZEXPORT inflateBackInit_ OF((z_streamp strm, int windowBits,
- unsigned char FAR *window,
- const char *version,
- int stream_size));
-#define deflateInit(strm, level) \
- deflateInit_((strm), (level), ZLIB_VERSION, (int)sizeof(z_stream))
-#define inflateInit(strm) \
- inflateInit_((strm), ZLIB_VERSION, (int)sizeof(z_stream))
-#define deflateInit2(strm, level, method, windowBits, memLevel, strategy) \
- deflateInit2_((strm),(level),(method),(windowBits),(memLevel),\
- (strategy), ZLIB_VERSION, (int)sizeof(z_stream))
-#define inflateInit2(strm, windowBits) \
- inflateInit2_((strm), (windowBits), ZLIB_VERSION, \
- (int)sizeof(z_stream))
-#define inflateBackInit(strm, windowBits, window) \
- inflateBackInit_((strm), (windowBits), (window), \
- ZLIB_VERSION, (int)sizeof(z_stream))
-
-#ifndef Z_SOLO
-
-/* gzgetc() macro and its supporting function and exposed data structure. Note
- * that the real internal state is much larger than the exposed structure.
- * This abbreviated structure exposes just enough for the gzgetc() macro. The
- * user should not mess with these exposed elements, since their names or
- * behavior could change in the future, perhaps even capriciously. They can
- * only be used by the gzgetc() macro. You have been warned.
- */
-struct gzFile_s {
- unsigned have;
- unsigned char *next;
- z_off64_t pos;
-};
-ZEXTERN int ZEXPORT gzgetc_ OF((gzFile file)); /* backward compatibility */
-#ifdef Z_PREFIX_SET
-# undef z_gzgetc
-# define z_gzgetc(g) \
- ((g)->have ? ((g)->have--, (g)->pos++, *((g)->next)++) : gzgetc(g))
-#else
-# define gzgetc(g) \
- ((g)->have ? ((g)->have--, (g)->pos++, *((g)->next)++) : gzgetc(g))
-#endif
-
-/* provide 64-bit offset functions if _LARGEFILE64_SOURCE defined, and/or
- * change the regular functions to 64 bits if _FILE_OFFSET_BITS is 64 (if
- * both are true, the application gets the *64 functions, and the regular
- * functions are changed to 64 bits) -- in case these are set on systems
- * without large file support, _LFS64_LARGEFILE must also be true
- */
-#ifdef Z_LARGE64
- ZEXTERN gzFile ZEXPORT gzopen64 OF((const char *, const char *));
- ZEXTERN z_off64_t ZEXPORT gzseek64 OF((gzFile, z_off64_t, int));
- ZEXTERN z_off64_t ZEXPORT gztell64 OF((gzFile));
- ZEXTERN z_off64_t ZEXPORT gzoffset64 OF((gzFile));
- ZEXTERN uLong ZEXPORT adler32_combine64 OF((uLong, uLong, z_off64_t));
- ZEXTERN uLong ZEXPORT crc32_combine64 OF((uLong, uLong, z_off64_t));
-#endif
-
-#if !defined(ZLIB_INTERNAL) && defined(Z_WANT64)
-# ifdef Z_PREFIX_SET
-# define z_gzopen z_gzopen64
-# define z_gzseek z_gzseek64
-# define z_gztell z_gztell64
-# define z_gzoffset z_gzoffset64
-# define z_adler32_combine z_adler32_combine64
-# define z_crc32_combine z_crc32_combine64
-# else
-# define gzopen gzopen64
-# define gzseek gzseek64
-# define gztell gztell64
-# define gzoffset gzoffset64
-# define adler32_combine adler32_combine64
-# define crc32_combine crc32_combine64
-# endif
-# ifndef Z_LARGE64
- ZEXTERN gzFile ZEXPORT gzopen64 OF((const char *, const char *));
- ZEXTERN off64_t ZEXPORT gzseek64 OF((gzFile, off64_t, int));
- ZEXTERN off64_t ZEXPORT gztell64 OF((gzFile));
- ZEXTERN z_off64_t ZEXPORT gzoffset64 OF((gzFile));
- ZEXTERN uLong ZEXPORT adler32_combine64 OF((uLong, uLong, off64_t));
- ZEXTERN uLong ZEXPORT crc32_combine64 OF((uLong, uLong, off64_t));
-# endif
-#else
- ZEXTERN gzFile ZEXPORT gzopen OF((const char *, const char *));
- ZEXTERN z_off_t ZEXPORT gzseek OF((gzFile, z_off_t, int));
- ZEXTERN z_off_t ZEXPORT gztell OF((gzFile));
- ZEXTERN z_off_t ZEXPORT gzoffset OF((gzFile));
- ZEXTERN uLong ZEXPORT adler32_combine OF((uLong, uLong, z_off_t));
- ZEXTERN uLong ZEXPORT crc32_combine OF((uLong, uLong, z_off_t));
-#endif
-
-#else /* Z_SOLO */
-
- ZEXTERN uLong ZEXPORT adler32_combine OF((uLong, uLong, z_off_t));
- ZEXTERN uLong ZEXPORT crc32_combine OF((uLong, uLong, z_off_t));
-
-#endif /* !Z_SOLO */
-
-/* hack for buggy compilers */
-#if !defined(ZUTIL_H) && !defined(NO_DUMMY_DECL)
- struct internal_state {int dummy;};
-#endif
-
-/* undocumented functions */
-ZEXTERN const char * ZEXPORT zError OF((int));
-ZEXTERN int ZEXPORT inflateSyncPoint OF((z_streamp));
-ZEXTERN const z_crc_t FAR * ZEXPORT get_crc_table OF((void));
-ZEXTERN int ZEXPORT inflateUndermine OF((z_streamp, int));
-ZEXTERN int ZEXPORT inflateResetKeep OF((z_streamp));
-ZEXTERN int ZEXPORT deflateResetKeep OF((z_streamp));
-#if defined(_WIN32) && !defined(Z_SOLO)
-ZEXTERN gzFile ZEXPORT gzopen_w OF((const wchar_t *path,
- const char *mode));
-#endif
-#if defined(STDC) || defined(Z_HAVE_STDARG_H)
-# ifndef Z_SOLO
-ZEXTERN int ZEXPORTVA gzvprintf Z_ARG((gzFile file,
- const char *format,
- va_list va));
-# endif
-#endif
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* ZLIB_H */
+/* zlib.h -- interface of the 'zlib' general purpose compression library + version 1.2.8, April 28th, 2013 + + Copyright (C) 1995-2013 Jean-loup Gailly and Mark Adler + + This software is provided 'as-is', without any express or implied + warranty. In no event will the authors be held liable for any damages + arising from the use of this software. + + Permission is granted to anyone to use this software for any purpose, + including commercial applications, and to alter it and redistribute it + freely, subject to the following restrictions: + + 1. The origin of this software must not be misrepresented; you must not + claim that you wrote the original software. If you use this software + in a product, an acknowledgment in the product documentation would be + appreciated but is not required. + 2. Altered source versions must be plainly marked as such, and must not be + misrepresented as being the original software. + 3. This notice may not be removed or altered from any source distribution. + + Jean-loup Gailly Mark Adler + jloup@gzip.org madler@alumni.caltech.edu + + + The data format used by the zlib library is described by RFCs (Request for + Comments) 1950 to 1952 in the files http://tools.ietf.org/html/rfc1950 + (zlib format), rfc1951 (deflate format) and rfc1952 (gzip format). +*/ + +#ifndef ZLIB_H +#define ZLIB_H + +#define deflate_copyright FPDFAPI_deflate_copyright +#define adler32 FPDFAPI_adler32 +#define compress2 FPDFAPI_compress2 +#define compress FPDFAPI_compress +#define compressBound FPDFAPI_compressBound +#define get_crc_table FPDFAPI_get_crc_table +#define crc32 FPDFAPI_crc32 +#define deflateInit_ FPDFAPI_deflateInit_ +#define deflateInit2_ FPDFAPI_deflateInit2_ +#define deflateSetDictionary FPDFAPI_deflateSetDictionary +#define deflateReset FPDFAPI_deflateReset +#define deflatePrime FPDFAPI_deflatePrime +#define deflateParams FPDFAPI_deflateParams +#define deflateBound FPDFAPI_deflateBound +#define deflateSetHeader FPDFAPI_deflateSetHeader +#define deflateTune FPDFAPI_deflateTune +#define deflate FPDFAPI_deflate +#define deflateEnd FPDFAPI_deflateEnd +#define deflateCopy FPDFAPI_deflateCopy +#define inflateBackInit_ FPDFAPI_inflateBackInit_ +#define inflateBack FPDFAPI_inflateBack +#define inflateBackEnd FPDFAPI_inflateBackEnd +#define inflateReset FPDFAPI_inflateReset +#define inflateInit2_ FPDFAPI_inflateInit2_ +#define inflateInit_ FPDFAPI_inflateInit_ +#define inflate FPDFAPI_inflate +#define inflateEnd FPDFAPI_inflateEnd +#define inflateSetDictionary FPDFAPI_inflateSetDictionary +#define inflateSync FPDFAPI_inflateSync +#define inflateSyncPoint FPDFAPI_inflateSyncPoint +#define inflateCopy FPDFAPI_inflateCopy +#define uncompress FPDFAPI_uncompress +#define zlibVersion FPDFAPI_zlibVersion +#define zlibCompileFlags FPDFAPI_zlibCompileFlags +#define zError FPDFAPI_zError +#define z_errmsg FPDFAPI_z_errmsg +#define zcfree FPDFAPI_zcfree +#define zcalloc FPDFAPI_zcalloc +#define inflate_fast FPDFAPI_inflate_fast +#define inflate_table FPDFAPI_inflate_table +#define inflate_copyright FPDFAPI_inflate_copyright +#define _length_code FPDFAPI_length_code +#define _tr_flush_block FPDFAPI_tr_flush_block +#define _dist_code FPDFAPI_dist_code +#define _tr_stored_block FPDFAPI_tr_stored_block +#define _tr_init FPDFAPI_tr_init +#define _tr_align FPDFAPI_tr_align +#define _tr_tally FPDFAPI_tr_tally +#define adler32_combine FPDFAPI_adler32_combine +#define inflatePrime FPDFAPI_inflatePrime +#define inflateGetHeader FPDFAPI_inflateGetHeader +#define crc32_combine FPDFAPI_crc32_combine +#define inflateReset2 FPDFAPI_inflateReset2 +#define inflateUndermine FPDFAPI_inflateUndermine +#define inflateMark FPDFAPI_inflateMark +#define adler32_combine64 FPDFAPI_adler32_combine64 + +#include "zconf.h" + +/* Sunliang.Liu 20100908 sync the config to the old revision. NO_GZIP */ +#define NO_GZIP /* XYQ */ + +#ifdef __cplusplus +extern "C" { +#endif + +#define ZLIB_VERSION "1.2.8" +#define ZLIB_VERNUM 0x1280 +#define ZLIB_VER_MAJOR 1 +#define ZLIB_VER_MINOR 2 +#define ZLIB_VER_REVISION 8 +#define ZLIB_VER_SUBREVISION 0 + +/* + The 'zlib' compression library provides in-memory compression and + decompression functions, including integrity checks of the uncompressed data. + This version of the library supports only one compression method (deflation) + but other algorithms will be added later and will have the same stream + interface. + + Compression can be done in a single step if the buffers are large enough, + or can be done by repeated calls of the compression function. In the latter + case, the application must provide more input and/or consume the output + (providing more output space) before each call. + + The compressed data format used by default by the in-memory functions is + the zlib format, which is a zlib wrapper documented in RFC 1950, wrapped + around a deflate stream, which is itself documented in RFC 1951. + + The library also supports reading and writing files in gzip (.gz) format + with an interface similar to that of stdio using the functions that start + with "gz". The gzip format is different from the zlib format. gzip is a + gzip wrapper, documented in RFC 1952, wrapped around a deflate stream. + + This library can optionally read and write gzip streams in memory as well. + + The zlib format was designed to be compact and fast for use in memory + and on communications channels. The gzip format was designed for single- + file compression on file systems, has a larger header than zlib to maintain + directory information, and uses a different, slower check method than zlib. + + The library does not install any signal handler. The decoder checks + the consistency of the compressed data, so the library should never crash + even in case of corrupted input. +*/ + +typedef voidpf (*alloc_func) OF((voidpf opaque, uInt items, uInt size)); +typedef void (*free_func) OF((voidpf opaque, voidpf address)); + +struct internal_state; + +typedef struct z_stream_s { + z_const Bytef *next_in; /* next input byte */ + uInt avail_in; /* number of bytes available at next_in */ + uLong total_in; /* total number of input bytes read so far */ + + Bytef *next_out; /* next output byte should be put there */ + uInt avail_out; /* remaining free space at next_out */ + uLong total_out; /* total number of bytes output so far */ + + z_const char *msg; /* last error message, NULL if no error */ + struct internal_state FAR *state; /* not visible by applications */ + + alloc_func zalloc; /* used to allocate the internal state */ + free_func zfree; /* used to free the internal state */ + voidpf opaque; /* private data object passed to zalloc and zfree */ + + int data_type; /* best guess about the data type: binary or text */ + uLong adler; /* adler32 value of the uncompressed data */ + uLong reserved; /* reserved for future use */ +} z_stream; + +typedef z_stream FAR *z_streamp; + +/* + gzip header information passed to and from zlib routines. See RFC 1952 + for more details on the meanings of these fields. +*/ +typedef struct gz_header_s { + int text; /* true if compressed data believed to be text */ + uLong time; /* modification time */ + int xflags; /* extra flags (not used when writing a gzip file) */ + int os; /* operating system */ + Bytef *extra; /* pointer to extra field or Z_NULL if none */ + uInt extra_len; /* extra field length (valid if extra != Z_NULL) */ + uInt extra_max; /* space at extra (only when reading header) */ + Bytef *name; /* pointer to zero-terminated file name or Z_NULL */ + uInt name_max; /* space at name (only when reading header) */ + Bytef *comment; /* pointer to zero-terminated comment or Z_NULL */ + uInt comm_max; /* space at comment (only when reading header) */ + int hcrc; /* true if there was or will be a header crc */ + int done; /* true when done reading gzip header (not used + when writing a gzip file) */ +} gz_header; + +typedef gz_header FAR *gz_headerp; + +/* + The application must update next_in and avail_in when avail_in has dropped + to zero. It must update next_out and avail_out when avail_out has dropped + to zero. The application must initialize zalloc, zfree and opaque before + calling the init function. All other fields are set by the compression + library and must not be updated by the application. + + The opaque value provided by the application will be passed as the first + parameter for calls of zalloc and zfree. This can be useful for custom + memory management. The compression library attaches no meaning to the + opaque value. + + zalloc must return Z_NULL if there is not enough memory for the object. + If zlib is used in a multi-threaded application, zalloc and zfree must be + thread safe. + + On 16-bit systems, the functions zalloc and zfree must be able to allocate + exactly 65536 bytes, but will not be required to allocate more than this if + the symbol MAXSEG_64K is defined (see zconf.h). WARNING: On MSDOS, pointers + returned by zalloc for objects of exactly 65536 bytes *must* have their + offset normalized to zero. The default allocation function provided by this + library ensures this (see zutil.c). To reduce memory requirements and avoid + any allocation of 64K objects, at the expense of compression ratio, compile + the library with -DMAX_WBITS=14 (see zconf.h). + + The fields total_in and total_out can be used for statistics or progress + reports. After compression, total_in holds the total size of the + uncompressed data and may be saved for use in the decompressor (particularly + if the decompressor wants to decompress everything in a single step). +*/ + + /* constants */ + +#define Z_NO_FLUSH 0 +#define Z_PARTIAL_FLUSH 1 +#define Z_SYNC_FLUSH 2 +#define Z_FULL_FLUSH 3 +#define Z_FINISH 4 +#define Z_BLOCK 5 +#define Z_TREES 6 +/* Allowed flush values; see deflate() and inflate() below for details */ + +#define Z_OK 0 +#define Z_STREAM_END 1 +#define Z_NEED_DICT 2 +#define Z_ERRNO (-1) +#define Z_STREAM_ERROR (-2) +#define Z_DATA_ERROR (-3) +#define Z_MEM_ERROR (-4) +#define Z_BUF_ERROR (-5) +#define Z_VERSION_ERROR (-6) +/* Return codes for the compression/decompression functions. Negative values + * are errors, positive values are used for special but normal events. + */ + +#define Z_NO_COMPRESSION 0 +#define Z_BEST_SPEED 1 +#define Z_BEST_COMPRESSION 9 +#define Z_DEFAULT_COMPRESSION (-1) +/* compression levels */ + +#define Z_FILTERED 1 +#define Z_HUFFMAN_ONLY 2 +#define Z_RLE 3 +#define Z_FIXED 4 +#define Z_DEFAULT_STRATEGY 0 +/* compression strategy; see deflateInit2() below for details */ + +#define Z_BINARY 0 +#define Z_TEXT 1 +#define Z_ASCII Z_TEXT /* for compatibility with 1.2.2 and earlier */ +#define Z_UNKNOWN 2 +/* Possible values of the data_type field (though see inflate()) */ + +#define Z_DEFLATED 8 +/* The deflate compression method (the only one supported in this version) */ + +#define Z_NULL 0 /* for initializing zalloc, zfree, opaque */ + +#define zlib_version zlibVersion() +/* for compatibility with versions < 1.0.2 */ + + + /* basic functions */ + +ZEXTERN const char * ZEXPORT zlibVersion OF((void)); +/* The application can compare zlibVersion and ZLIB_VERSION for consistency. + If the first character differs, the library code actually used is not + compatible with the zlib.h header file used by the application. This check + is automatically made by deflateInit and inflateInit. + */ + +/* +ZEXTERN int ZEXPORT deflateInit OF((z_streamp strm, int level)); + + Initializes the internal stream state for compression. The fields + zalloc, zfree and opaque must be initialized before by the caller. If + zalloc and zfree are set to Z_NULL, deflateInit updates them to use default + allocation functions. + + The compression level must be Z_DEFAULT_COMPRESSION, or between 0 and 9: + 1 gives best speed, 9 gives best compression, 0 gives no compression at all + (the input data is simply copied a block at a time). Z_DEFAULT_COMPRESSION + requests a default compromise between speed and compression (currently + equivalent to level 6). + + deflateInit returns Z_OK if success, Z_MEM_ERROR if there was not enough + memory, Z_STREAM_ERROR if level is not a valid compression level, or + Z_VERSION_ERROR if the zlib library version (zlib_version) is incompatible + with the version assumed by the caller (ZLIB_VERSION). msg is set to null + if there is no error message. deflateInit does not perform any compression: + this will be done by deflate(). +*/ + + +ZEXTERN int ZEXPORT deflate OF((z_streamp strm, int flush)); +/* + deflate compresses as much data as possible, and stops when the input + buffer becomes empty or the output buffer becomes full. It may introduce + some output latency (reading input without producing any output) except when + forced to flush. + + The detailed semantics are as follows. deflate performs one or both of the + following actions: + + - Compress more input starting at next_in and update next_in and avail_in + accordingly. If not all input can be processed (because there is not + enough room in the output buffer), next_in and avail_in are updated and + processing will resume at this point for the next call of deflate(). + + - Provide more output starting at next_out and update next_out and avail_out + accordingly. This action is forced if the parameter flush is non zero. + Forcing flush frequently degrades the compression ratio, so this parameter + should be set only when necessary (in interactive applications). Some + output may be provided even if flush is not set. + + Before the call of deflate(), the application should ensure that at least + one of the actions is possible, by providing more input and/or consuming more + output, and updating avail_in or avail_out accordingly; avail_out should + never be zero before the call. The application can consume the compressed + output when it wants, for example when the output buffer is full (avail_out + == 0), or after each call of deflate(). If deflate returns Z_OK and with + zero avail_out, it must be called again after making room in the output + buffer because there might be more output pending. + + Normally the parameter flush is set to Z_NO_FLUSH, which allows deflate to + decide how much data to accumulate before producing output, in order to + maximize compression. + + If the parameter flush is set to Z_SYNC_FLUSH, all pending output is + flushed to the output buffer and the output is aligned on a byte boundary, so + that the decompressor can get all input data available so far. (In + particular avail_in is zero after the call if enough output space has been + provided before the call.) Flushing may degrade compression for some + compression algorithms and so it should be used only when necessary. This + completes the current deflate block and follows it with an empty stored block + that is three bits plus filler bits to the next byte, followed by four bytes + (00 00 ff ff). + + If flush is set to Z_PARTIAL_FLUSH, all pending output is flushed to the + output buffer, but the output is not aligned to a byte boundary. All of the + input data so far will be available to the decompressor, as for Z_SYNC_FLUSH. + This completes the current deflate block and follows it with an empty fixed + codes block that is 10 bits long. This assures that enough bytes are output + in order for the decompressor to finish the block before the empty fixed code + block. + + If flush is set to Z_BLOCK, a deflate block is completed and emitted, as + for Z_SYNC_FLUSH, but the output is not aligned on a byte boundary, and up to + seven bits of the current block are held to be written as the next byte after + the next deflate block is completed. In this case, the decompressor may not + be provided enough bits at this point in order to complete decompression of + the data provided so far to the compressor. It may need to wait for the next + block to be emitted. This is for advanced applications that need to control + the emission of deflate blocks. + + If flush is set to Z_FULL_FLUSH, all output is flushed as with + Z_SYNC_FLUSH, and the compression state is reset so that decompression can + restart from this point if previous compressed data has been damaged or if + random access is desired. Using Z_FULL_FLUSH too often can seriously degrade + compression. + + If deflate returns with avail_out == 0, this function must be called again + with the same value of the flush parameter and more output space (updated + avail_out), until the flush is complete (deflate returns with non-zero + avail_out). In the case of a Z_FULL_FLUSH or Z_SYNC_FLUSH, make sure that + avail_out is greater than six to avoid repeated flush markers due to + avail_out == 0 on return. + + If the parameter flush is set to Z_FINISH, pending input is processed, + pending output is flushed and deflate returns with Z_STREAM_END if there was + enough output space; if deflate returns with Z_OK, this function must be + called again with Z_FINISH and more output space (updated avail_out) but no + more input data, until it returns with Z_STREAM_END or an error. After + deflate has returned Z_STREAM_END, the only possible operations on the stream + are deflateReset or deflateEnd. + + Z_FINISH can be used immediately after deflateInit if all the compression + is to be done in a single step. In this case, avail_out must be at least the + value returned by deflateBound (see below). Then deflate is guaranteed to + return Z_STREAM_END. If not enough output space is provided, deflate will + not return Z_STREAM_END, and it must be called again as described above. + + deflate() sets strm->adler to the adler32 checksum of all input read + so far (that is, total_in bytes). + + deflate() may update strm->data_type if it can make a good guess about + the input data type (Z_BINARY or Z_TEXT). In doubt, the data is considered + binary. This field is only for information purposes and does not affect the + compression algorithm in any manner. + + deflate() returns Z_OK if some progress has been made (more input + processed or more output produced), Z_STREAM_END if all input has been + consumed and all output has been produced (only when flush is set to + Z_FINISH), Z_STREAM_ERROR if the stream state was inconsistent (for example + if next_in or next_out was Z_NULL), Z_BUF_ERROR if no progress is possible + (for example avail_in or avail_out was zero). Note that Z_BUF_ERROR is not + fatal, and deflate() can be called again with more input and more output + space to continue compressing. +*/ + + +ZEXTERN int ZEXPORT deflateEnd OF((z_streamp strm)); +/* + All dynamically allocated data structures for this stream are freed. + This function discards any unprocessed input and does not flush any pending + output. + + deflateEnd returns Z_OK if success, Z_STREAM_ERROR if the + stream state was inconsistent, Z_DATA_ERROR if the stream was freed + prematurely (some input or output was discarded). In the error case, msg + may be set but then points to a static string (which must not be + deallocated). +*/ + + +/* +ZEXTERN int ZEXPORT inflateInit OF((z_streamp strm)); + + Initializes the internal stream state for decompression. The fields + next_in, avail_in, zalloc, zfree and opaque must be initialized before by + the caller. If next_in is not Z_NULL and avail_in is large enough (the + exact value depends on the compression method), inflateInit determines the + compression method from the zlib header and allocates all data structures + accordingly; otherwise the allocation will be deferred to the first call of + inflate. If zalloc and zfree are set to Z_NULL, inflateInit updates them to + use default allocation functions. + + inflateInit returns Z_OK if success, Z_MEM_ERROR if there was not enough + memory, Z_VERSION_ERROR if the zlib library version is incompatible with the + version assumed by the caller, or Z_STREAM_ERROR if the parameters are + invalid, such as a null pointer to the structure. msg is set to null if + there is no error message. inflateInit does not perform any decompression + apart from possibly reading the zlib header if present: actual decompression + will be done by inflate(). (So next_in and avail_in may be modified, but + next_out and avail_out are unused and unchanged.) The current implementation + of inflateInit() does not process any header information -- that is deferred + until inflate() is called. +*/ + + +ZEXTERN int ZEXPORT inflate OF((z_streamp strm, int flush)); +/* + inflate decompresses as much data as possible, and stops when the input + buffer becomes empty or the output buffer becomes full. It may introduce + some output latency (reading input without producing any output) except when + forced to flush. + + The detailed semantics are as follows. inflate performs one or both of the + following actions: + + - Decompress more input starting at next_in and update next_in and avail_in + accordingly. If not all input can be processed (because there is not + enough room in the output buffer), next_in is updated and processing will + resume at this point for the next call of inflate(). + + - Provide more output starting at next_out and update next_out and avail_out + accordingly. inflate() provides as much output as possible, until there is + no more input data or no more space in the output buffer (see below about + the flush parameter). + + Before the call of inflate(), the application should ensure that at least + one of the actions is possible, by providing more input and/or consuming more + output, and updating the next_* and avail_* values accordingly. The + application can consume the uncompressed output when it wants, for example + when the output buffer is full (avail_out == 0), or after each call of + inflate(). If inflate returns Z_OK and with zero avail_out, it must be + called again after making room in the output buffer because there might be + more output pending. + + The flush parameter of inflate() can be Z_NO_FLUSH, Z_SYNC_FLUSH, Z_FINISH, + Z_BLOCK, or Z_TREES. Z_SYNC_FLUSH requests that inflate() flush as much + output as possible to the output buffer. Z_BLOCK requests that inflate() + stop if and when it gets to the next deflate block boundary. When decoding + the zlib or gzip format, this will cause inflate() to return immediately + after the header and before the first block. When doing a raw inflate, + inflate() will go ahead and process the first block, and will return when it + gets to the end of that block, or when it runs out of data. + + The Z_BLOCK option assists in appending to or combining deflate streams. + Also to assist in this, on return inflate() will set strm->data_type to the + number of unused bits in the last byte taken from strm->next_in, plus 64 if + inflate() is currently decoding the last block in the deflate stream, plus + 128 if inflate() returned immediately after decoding an end-of-block code or + decoding the complete header up to just before the first byte of the deflate + stream. The end-of-block will not be indicated until all of the uncompressed + data from that block has been written to strm->next_out. The number of + unused bits may in general be greater than seven, except when bit 7 of + data_type is set, in which case the number of unused bits will be less than + eight. data_type is set as noted here every time inflate() returns for all + flush options, and so can be used to determine the amount of currently + consumed input in bits. + + The Z_TREES option behaves as Z_BLOCK does, but it also returns when the + end of each deflate block header is reached, before any actual data in that + block is decoded. This allows the caller to determine the length of the + deflate block header for later use in random access within a deflate block. + 256 is added to the value of strm->data_type when inflate() returns + immediately after reaching the end of the deflate block header. + + inflate() should normally be called until it returns Z_STREAM_END or an + error. However if all decompression is to be performed in a single step (a + single call of inflate), the parameter flush should be set to Z_FINISH. In + this case all pending input is processed and all pending output is flushed; + avail_out must be large enough to hold all of the uncompressed data for the + operation to complete. (The size of the uncompressed data may have been + saved by the compressor for this purpose.) The use of Z_FINISH is not + required to perform an inflation in one step. However it may be used to + inform inflate that a faster approach can be used for the single inflate() + call. Z_FINISH also informs inflate to not maintain a sliding window if the + stream completes, which reduces inflate's memory footprint. If the stream + does not complete, either because not all of the stream is provided or not + enough output space is provided, then a sliding window will be allocated and + inflate() can be called again to continue the operation as if Z_NO_FLUSH had + been used. + + In this implementation, inflate() always flushes as much output as + possible to the output buffer, and always uses the faster approach on the + first call. So the effects of the flush parameter in this implementation are + on the return value of inflate() as noted below, when inflate() returns early + when Z_BLOCK or Z_TREES is used, and when inflate() avoids the allocation of + memory for a sliding window when Z_FINISH is used. + + If a preset dictionary is needed after this call (see inflateSetDictionary + below), inflate sets strm->adler to the Adler-32 checksum of the dictionary + chosen by the compressor and returns Z_NEED_DICT; otherwise it sets + strm->adler to the Adler-32 checksum of all output produced so far (that is, + total_out bytes) and returns Z_OK, Z_STREAM_END or an error code as described + below. At the end of the stream, inflate() checks that its computed adler32 + checksum is equal to that saved by the compressor and returns Z_STREAM_END + only if the checksum is correct. + + inflate() can decompress and check either zlib-wrapped or gzip-wrapped + deflate data. The header type is detected automatically, if requested when + initializing with inflateInit2(). Any information contained in the gzip + header is not retained, so applications that need that information should + instead use raw inflate, see inflateInit2() below, or inflateBack() and + perform their own processing of the gzip header and trailer. When processing + gzip-wrapped deflate data, strm->adler32 is set to the CRC-32 of the output + producted so far. The CRC-32 is checked against the gzip trailer. + + inflate() returns Z_OK if some progress has been made (more input processed + or more output produced), Z_STREAM_END if the end of the compressed data has + been reached and all uncompressed output has been produced, Z_NEED_DICT if a + preset dictionary is needed at this point, Z_DATA_ERROR if the input data was + corrupted (input stream not conforming to the zlib format or incorrect check + value), Z_STREAM_ERROR if the stream structure was inconsistent (for example + next_in or next_out was Z_NULL), Z_MEM_ERROR if there was not enough memory, + Z_BUF_ERROR if no progress is possible or if there was not enough room in the + output buffer when Z_FINISH is used. Note that Z_BUF_ERROR is not fatal, and + inflate() can be called again with more input and more output space to + continue decompressing. If Z_DATA_ERROR is returned, the application may + then call inflateSync() to look for a good compression block if a partial + recovery of the data is desired. +*/ + + +ZEXTERN int ZEXPORT inflateEnd OF((z_streamp strm)); +/* + All dynamically allocated data structures for this stream are freed. + This function discards any unprocessed input and does not flush any pending + output. + + inflateEnd returns Z_OK if success, Z_STREAM_ERROR if the stream state + was inconsistent. In the error case, msg may be set but then points to a + static string (which must not be deallocated). +*/ + + + /* Advanced functions */ + +/* + The following functions are needed only in some special applications. +*/ + +/* +ZEXTERN int ZEXPORT deflateInit2 OF((z_streamp strm, + int level, + int method, + int windowBits, + int memLevel, + int strategy)); + + This is another version of deflateInit with more compression options. The + fields next_in, zalloc, zfree and opaque must be initialized before by the + caller. + + The method parameter is the compression method. It must be Z_DEFLATED in + this version of the library. + + The windowBits parameter is the base two logarithm of the window size + (the size of the history buffer). It should be in the range 8..15 for this + version of the library. Larger values of this parameter result in better + compression at the expense of memory usage. The default value is 15 if + deflateInit is used instead. + + windowBits can also be -8..-15 for raw deflate. In this case, -windowBits + determines the window size. deflate() will then generate raw deflate data + with no zlib header or trailer, and will not compute an adler32 check value. + + windowBits can also be greater than 15 for optional gzip encoding. Add + 16 to windowBits to write a simple gzip header and trailer around the + compressed data instead of a zlib wrapper. The gzip header will have no + file name, no extra data, no comment, no modification time (set to zero), no + header crc, and the operating system will be set to 255 (unknown). If a + gzip stream is being written, strm->adler is a crc32 instead of an adler32. + + The memLevel parameter specifies how much memory should be allocated + for the internal compression state. memLevel=1 uses minimum memory but is + slow and reduces compression ratio; memLevel=9 uses maximum memory for + optimal speed. The default value is 8. See zconf.h for total memory usage + as a function of windowBits and memLevel. + + The strategy parameter is used to tune the compression algorithm. Use the + value Z_DEFAULT_STRATEGY for normal data, Z_FILTERED for data produced by a + filter (or predictor), Z_HUFFMAN_ONLY to force Huffman encoding only (no + string match), or Z_RLE to limit match distances to one (run-length + encoding). Filtered data consists mostly of small values with a somewhat + random distribution. In this case, the compression algorithm is tuned to + compress them better. The effect of Z_FILTERED is to force more Huffman + coding and less string matching; it is somewhat intermediate between + Z_DEFAULT_STRATEGY and Z_HUFFMAN_ONLY. Z_RLE is designed to be almost as + fast as Z_HUFFMAN_ONLY, but give better compression for PNG image data. The + strategy parameter only affects the compression ratio but not the + correctness of the compressed output even if it is not set appropriately. + Z_FIXED prevents the use of dynamic Huffman codes, allowing for a simpler + decoder for special applications. + + deflateInit2 returns Z_OK if success, Z_MEM_ERROR if there was not enough + memory, Z_STREAM_ERROR if any parameter is invalid (such as an invalid + method), or Z_VERSION_ERROR if the zlib library version (zlib_version) is + incompatible with the version assumed by the caller (ZLIB_VERSION). msg is + set to null if there is no error message. deflateInit2 does not perform any + compression: this will be done by deflate(). +*/ + +ZEXTERN int ZEXPORT deflateSetDictionary OF((z_streamp strm, + const Bytef *dictionary, + uInt dictLength)); +/* + Initializes the compression dictionary from the given byte sequence + without producing any compressed output. When using the zlib format, this + function must be called immediately after deflateInit, deflateInit2 or + deflateReset, and before any call of deflate. When doing raw deflate, this + function must be called either before any call of deflate, or immediately + after the completion of a deflate block, i.e. after all input has been + consumed and all output has been delivered when using any of the flush + options Z_BLOCK, Z_PARTIAL_FLUSH, Z_SYNC_FLUSH, or Z_FULL_FLUSH. The + compressor and decompressor must use exactly the same dictionary (see + inflateSetDictionary). + + The dictionary should consist of strings (byte sequences) that are likely + to be encountered later in the data to be compressed, with the most commonly + used strings preferably put towards the end of the dictionary. Using a + dictionary is most useful when the data to be compressed is short and can be + predicted with good accuracy; the data can then be compressed better than + with the default empty dictionary. + + Depending on the size of the compression data structures selected by + deflateInit or deflateInit2, a part of the dictionary may in effect be + discarded, for example if the dictionary is larger than the window size + provided in deflateInit or deflateInit2. Thus the strings most likely to be + useful should be put at the end of the dictionary, not at the front. In + addition, the current implementation of deflate will use at most the window + size minus 262 bytes of the provided dictionary. + + Upon return of this function, strm->adler is set to the adler32 value + of the dictionary; the decompressor may later use this value to determine + which dictionary has been used by the compressor. (The adler32 value + applies to the whole dictionary even if only a subset of the dictionary is + actually used by the compressor.) If a raw deflate was requested, then the + adler32 value is not computed and strm->adler is not set. + + deflateSetDictionary returns Z_OK if success, or Z_STREAM_ERROR if a + parameter is invalid (e.g. dictionary being Z_NULL) or the stream state is + inconsistent (for example if deflate has already been called for this stream + or if not at a block boundary for raw deflate). deflateSetDictionary does + not perform any compression: this will be done by deflate(). +*/ + +ZEXTERN int ZEXPORT deflateCopy OF((z_streamp dest, + z_streamp source)); +/* + Sets the destination stream as a complete copy of the source stream. + + This function can be useful when several compression strategies will be + tried, for example when there are several ways of pre-processing the input + data with a filter. The streams that will be discarded should then be freed + by calling deflateEnd. Note that deflateCopy duplicates the internal + compression state which can be quite large, so this strategy is slow and can + consume lots of memory. + + deflateCopy returns Z_OK if success, Z_MEM_ERROR if there was not + enough memory, Z_STREAM_ERROR if the source stream state was inconsistent + (such as zalloc being Z_NULL). msg is left unchanged in both source and + destination. +*/ + +ZEXTERN int ZEXPORT deflateReset OF((z_streamp strm)); +/* + This function is equivalent to deflateEnd followed by deflateInit, + but does not free and reallocate all the internal compression state. The + stream will keep the same compression level and any other attributes that + may have been set by deflateInit2. + + deflateReset returns Z_OK if success, or Z_STREAM_ERROR if the source + stream state was inconsistent (such as zalloc or state being Z_NULL). +*/ + +ZEXTERN int ZEXPORT deflateParams OF((z_streamp strm, + int level, + int strategy)); +/* + Dynamically update the compression level and compression strategy. The + interpretation of level and strategy is as in deflateInit2. This can be + used to switch between compression and straight copy of the input data, or + to switch to a different kind of input data requiring a different strategy. + If the compression level is changed, the input available so far is + compressed with the old level (and may be flushed); the new level will take + effect only at the next call of deflate(). + + Before the call of deflateParams, the stream state must be set as for + a call of deflate(), since the currently available input may have to be + compressed and flushed. In particular, strm->avail_out must be non-zero. + + deflateParams returns Z_OK if success, Z_STREAM_ERROR if the source + stream state was inconsistent or if a parameter was invalid, Z_BUF_ERROR if + strm->avail_out was zero. +*/ + +ZEXTERN int ZEXPORT deflateTune OF((z_streamp strm, + int good_length, + int max_lazy, + int nice_length, + int max_chain)); +/* + Fine tune deflate's internal compression parameters. This should only be + used by someone who understands the algorithm used by zlib's deflate for + searching for the best matching string, and even then only by the most + fanatic optimizer trying to squeeze out the last compressed bit for their + specific input data. Read the deflate.c source code for the meaning of the + max_lazy, good_length, nice_length, and max_chain parameters. + + deflateTune() can be called after deflateInit() or deflateInit2(), and + returns Z_OK on success, or Z_STREAM_ERROR for an invalid deflate stream. + */ + +ZEXTERN uLong ZEXPORT deflateBound OF((z_streamp strm, + uLong sourceLen)); +/* + deflateBound() returns an upper bound on the compressed size after + deflation of sourceLen bytes. It must be called after deflateInit() or + deflateInit2(), and after deflateSetHeader(), if used. This would be used + to allocate an output buffer for deflation in a single pass, and so would be + called before deflate(). If that first deflate() call is provided the + sourceLen input bytes, an output buffer allocated to the size returned by + deflateBound(), and the flush value Z_FINISH, then deflate() is guaranteed + to return Z_STREAM_END. Note that it is possible for the compressed size to + be larger than the value returned by deflateBound() if flush options other + than Z_FINISH or Z_NO_FLUSH are used. +*/ + +ZEXTERN int ZEXPORT deflatePending OF((z_streamp strm, + unsigned *pending, + int *bits)); +/* + deflatePending() returns the number of bytes and bits of output that have + been generated, but not yet provided in the available output. The bytes not + provided would be due to the available output space having being consumed. + The number of bits of output not provided are between 0 and 7, where they + await more bits to join them in order to fill out a full byte. If pending + or bits are Z_NULL, then those values are not set. + + deflatePending returns Z_OK if success, or Z_STREAM_ERROR if the source + stream state was inconsistent. + */ + +ZEXTERN int ZEXPORT deflatePrime OF((z_streamp strm, + int bits, + int value)); +/* + deflatePrime() inserts bits in the deflate output stream. The intent + is that this function is used to start off the deflate output with the bits + leftover from a previous deflate stream when appending to it. As such, this + function can only be used for raw deflate, and must be used before the first + deflate() call after a deflateInit2() or deflateReset(). bits must be less + than or equal to 16, and that many of the least significant bits of value + will be inserted in the output. + + deflatePrime returns Z_OK if success, Z_BUF_ERROR if there was not enough + room in the internal buffer to insert the bits, or Z_STREAM_ERROR if the + source stream state was inconsistent. +*/ + +ZEXTERN int ZEXPORT deflateSetHeader OF((z_streamp strm, + gz_headerp head)); +/* + deflateSetHeader() provides gzip header information for when a gzip + stream is requested by deflateInit2(). deflateSetHeader() may be called + after deflateInit2() or deflateReset() and before the first call of + deflate(). The text, time, os, extra field, name, and comment information + in the provided gz_header structure are written to the gzip header (xflag is + ignored -- the extra flags are set according to the compression level). The + caller must assure that, if not Z_NULL, name and comment are terminated with + a zero byte, and that if extra is not Z_NULL, that extra_len bytes are + available there. If hcrc is true, a gzip header crc is included. Note that + the current versions of the command-line version of gzip (up through version + 1.3.x) do not support header crc's, and will report that it is a "multi-part + gzip file" and give up. + + If deflateSetHeader is not used, the default gzip header has text false, + the time set to zero, and os set to 255, with no extra, name, or comment + fields. The gzip header is returned to the default state by deflateReset(). + + deflateSetHeader returns Z_OK if success, or Z_STREAM_ERROR if the source + stream state was inconsistent. +*/ + +/* +ZEXTERN int ZEXPORT inflateInit2 OF((z_streamp strm, + int windowBits)); + + This is another version of inflateInit with an extra parameter. The + fields next_in, avail_in, zalloc, zfree and opaque must be initialized + before by the caller. + + The windowBits parameter is the base two logarithm of the maximum window + size (the size of the history buffer). It should be in the range 8..15 for + this version of the library. The default value is 15 if inflateInit is used + instead. windowBits must be greater than or equal to the windowBits value + provided to deflateInit2() while compressing, or it must be equal to 15 if + deflateInit2() was not used. If a compressed stream with a larger window + size is given as input, inflate() will return with the error code + Z_DATA_ERROR instead of trying to allocate a larger window. + + windowBits can also be zero to request that inflate use the window size in + the zlib header of the compressed stream. + + windowBits can also be -8..-15 for raw inflate. In this case, -windowBits + determines the window size. inflate() will then process raw deflate data, + not looking for a zlib or gzip header, not generating a check value, and not + looking for any check values for comparison at the end of the stream. This + is for use with other formats that use the deflate compressed data format + such as zip. Those formats provide their own check values. If a custom + format is developed using the raw deflate format for compressed data, it is + recommended that a check value such as an adler32 or a crc32 be applied to + the uncompressed data as is done in the zlib, gzip, and zip formats. For + most applications, the zlib format should be used as is. Note that comments + above on the use in deflateInit2() applies to the magnitude of windowBits. + + windowBits can also be greater than 15 for optional gzip decoding. Add + 32 to windowBits to enable zlib and gzip decoding with automatic header + detection, or add 16 to decode only the gzip format (the zlib format will + return a Z_DATA_ERROR). If a gzip stream is being decoded, strm->adler is a + crc32 instead of an adler32. + + inflateInit2 returns Z_OK if success, Z_MEM_ERROR if there was not enough + memory, Z_VERSION_ERROR if the zlib library version is incompatible with the + version assumed by the caller, or Z_STREAM_ERROR if the parameters are + invalid, such as a null pointer to the structure. msg is set to null if + there is no error message. inflateInit2 does not perform any decompression + apart from possibly reading the zlib header if present: actual decompression + will be done by inflate(). (So next_in and avail_in may be modified, but + next_out and avail_out are unused and unchanged.) The current implementation + of inflateInit2() does not process any header information -- that is + deferred until inflate() is called. +*/ + +ZEXTERN int ZEXPORT inflateSetDictionary OF((z_streamp strm, + const Bytef *dictionary, + uInt dictLength)); +/* + Initializes the decompression dictionary from the given uncompressed byte + sequence. This function must be called immediately after a call of inflate, + if that call returned Z_NEED_DICT. The dictionary chosen by the compressor + can be determined from the adler32 value returned by that call of inflate. + The compressor and decompressor must use exactly the same dictionary (see + deflateSetDictionary). For raw inflate, this function can be called at any + time to set the dictionary. If the provided dictionary is smaller than the + window and there is already data in the window, then the provided dictionary + will amend what's there. The application must insure that the dictionary + that was used for compression is provided. + + inflateSetDictionary returns Z_OK if success, Z_STREAM_ERROR if a + parameter is invalid (e.g. dictionary being Z_NULL) or the stream state is + inconsistent, Z_DATA_ERROR if the given dictionary doesn't match the + expected one (incorrect adler32 value). inflateSetDictionary does not + perform any decompression: this will be done by subsequent calls of + inflate(). +*/ + +ZEXTERN int ZEXPORT inflateGetDictionary OF((z_streamp strm, + Bytef *dictionary, + uInt *dictLength)); +/* + Returns the sliding dictionary being maintained by inflate. dictLength is + set to the number of bytes in the dictionary, and that many bytes are copied + to dictionary. dictionary must have enough space, where 32768 bytes is + always enough. If inflateGetDictionary() is called with dictionary equal to + Z_NULL, then only the dictionary length is returned, and nothing is copied. + Similary, if dictLength is Z_NULL, then it is not set. + + inflateGetDictionary returns Z_OK on success, or Z_STREAM_ERROR if the + stream state is inconsistent. +*/ + +ZEXTERN int ZEXPORT inflateSync OF((z_streamp strm)); +/* + Skips invalid compressed data until a possible full flush point (see above + for the description of deflate with Z_FULL_FLUSH) can be found, or until all + available input is skipped. No output is provided. + + inflateSync searches for a 00 00 FF FF pattern in the compressed data. + All full flush points have this pattern, but not all occurrences of this + pattern are full flush points. + + inflateSync returns Z_OK if a possible full flush point has been found, + Z_BUF_ERROR if no more input was provided, Z_DATA_ERROR if no flush point + has been found, or Z_STREAM_ERROR if the stream structure was inconsistent. + In the success case, the application may save the current current value of + total_in which indicates where valid compressed data was found. In the + error case, the application may repeatedly call inflateSync, providing more + input each time, until success or end of the input data. +*/ + +ZEXTERN int ZEXPORT inflateCopy OF((z_streamp dest, + z_streamp source)); +/* + Sets the destination stream as a complete copy of the source stream. + + This function can be useful when randomly accessing a large stream. The + first pass through the stream can periodically record the inflate state, + allowing restarting inflate at those points when randomly accessing the + stream. + + inflateCopy returns Z_OK if success, Z_MEM_ERROR if there was not + enough memory, Z_STREAM_ERROR if the source stream state was inconsistent + (such as zalloc being Z_NULL). msg is left unchanged in both source and + destination. +*/ + +ZEXTERN int ZEXPORT inflateReset OF((z_streamp strm)); +/* + This function is equivalent to inflateEnd followed by inflateInit, + but does not free and reallocate all the internal decompression state. The + stream will keep attributes that may have been set by inflateInit2. + + inflateReset returns Z_OK if success, or Z_STREAM_ERROR if the source + stream state was inconsistent (such as zalloc or state being Z_NULL). +*/ + +ZEXTERN int ZEXPORT inflateReset2 OF((z_streamp strm, + int windowBits)); +/* + This function is the same as inflateReset, but it also permits changing + the wrap and window size requests. The windowBits parameter is interpreted + the same as it is for inflateInit2. + + inflateReset2 returns Z_OK if success, or Z_STREAM_ERROR if the source + stream state was inconsistent (such as zalloc or state being Z_NULL), or if + the windowBits parameter is invalid. +*/ + +ZEXTERN int ZEXPORT inflatePrime OF((z_streamp strm, + int bits, + int value)); +/* + This function inserts bits in the inflate input stream. The intent is + that this function is used to start inflating at a bit position in the + middle of a byte. The provided bits will be used before any bytes are used + from next_in. This function should only be used with raw inflate, and + should be used before the first inflate() call after inflateInit2() or + inflateReset(). bits must be less than or equal to 16, and that many of the + least significant bits of value will be inserted in the input. + + If bits is negative, then the input stream bit buffer is emptied. Then + inflatePrime() can be called again to put bits in the buffer. This is used + to clear out bits leftover after feeding inflate a block description prior + to feeding inflate codes. + + inflatePrime returns Z_OK if success, or Z_STREAM_ERROR if the source + stream state was inconsistent. +*/ + +ZEXTERN long ZEXPORT inflateMark OF((z_streamp strm)); +/* + This function returns two values, one in the lower 16 bits of the return + value, and the other in the remaining upper bits, obtained by shifting the + return value down 16 bits. If the upper value is -1 and the lower value is + zero, then inflate() is currently decoding information outside of a block. + If the upper value is -1 and the lower value is non-zero, then inflate is in + the middle of a stored block, with the lower value equaling the number of + bytes from the input remaining to copy. If the upper value is not -1, then + it is the number of bits back from the current bit position in the input of + the code (literal or length/distance pair) currently being processed. In + that case the lower value is the number of bytes already emitted for that + code. + + A code is being processed if inflate is waiting for more input to complete + decoding of the code, or if it has completed decoding but is waiting for + more output space to write the literal or match data. + + inflateMark() is used to mark locations in the input data for random + access, which may be at bit positions, and to note those cases where the + output of a code may span boundaries of random access blocks. The current + location in the input stream can be determined from avail_in and data_type + as noted in the description for the Z_BLOCK flush parameter for inflate. + + inflateMark returns the value noted above or -1 << 16 if the provided + source stream state was inconsistent. +*/ + +ZEXTERN int ZEXPORT inflateGetHeader OF((z_streamp strm, + gz_headerp head)); +/* + inflateGetHeader() requests that gzip header information be stored in the + provided gz_header structure. inflateGetHeader() may be called after + inflateInit2() or inflateReset(), and before the first call of inflate(). + As inflate() processes the gzip stream, head->done is zero until the header + is completed, at which time head->done is set to one. If a zlib stream is + being decoded, then head->done is set to -1 to indicate that there will be + no gzip header information forthcoming. Note that Z_BLOCK or Z_TREES can be + used to force inflate() to return immediately after header processing is + complete and before any actual data is decompressed. + + The text, time, xflags, and os fields are filled in with the gzip header + contents. hcrc is set to true if there is a header CRC. (The header CRC + was valid if done is set to one.) If extra is not Z_NULL, then extra_max + contains the maximum number of bytes to write to extra. Once done is true, + extra_len contains the actual extra field length, and extra contains the + extra field, or that field truncated if extra_max is less than extra_len. + If name is not Z_NULL, then up to name_max characters are written there, + terminated with a zero unless the length is greater than name_max. If + comment is not Z_NULL, then up to comm_max characters are written there, + terminated with a zero unless the length is greater than comm_max. When any + of extra, name, or comment are not Z_NULL and the respective field is not + present in the header, then that field is set to Z_NULL to signal its + absence. This allows the use of deflateSetHeader() with the returned + structure to duplicate the header. However if those fields are set to + allocated memory, then the application will need to save those pointers + elsewhere so that they can be eventually freed. + + If inflateGetHeader is not used, then the header information is simply + discarded. The header is always checked for validity, including the header + CRC if present. inflateReset() will reset the process to discard the header + information. The application would need to call inflateGetHeader() again to + retrieve the header from the next gzip stream. + + inflateGetHeader returns Z_OK if success, or Z_STREAM_ERROR if the source + stream state was inconsistent. +*/ + +/* +ZEXTERN int ZEXPORT inflateBackInit OF((z_streamp strm, int windowBits, + unsigned char FAR *window)); + + Initialize the internal stream state for decompression using inflateBack() + calls. The fields zalloc, zfree and opaque in strm must be initialized + before the call. If zalloc and zfree are Z_NULL, then the default library- + derived memory allocation routines are used. windowBits is the base two + logarithm of the window size, in the range 8..15. window is a caller + supplied buffer of that size. Except for special applications where it is + assured that deflate was used with small window sizes, windowBits must be 15 + and a 32K byte window must be supplied to be able to decompress general + deflate streams. + + See inflateBack() for the usage of these routines. + + inflateBackInit will return Z_OK on success, Z_STREAM_ERROR if any of + the parameters are invalid, Z_MEM_ERROR if the internal state could not be + allocated, or Z_VERSION_ERROR if the version of the library does not match + the version of the header file. +*/ + +typedef unsigned (*in_func) OF((void FAR *, + z_const unsigned char FAR * FAR *)); +typedef int (*out_func) OF((void FAR *, unsigned char FAR *, unsigned)); + +ZEXTERN int ZEXPORT inflateBack OF((z_streamp strm, + in_func in, void FAR *in_desc, + out_func out, void FAR *out_desc)); +/* + inflateBack() does a raw inflate with a single call using a call-back + interface for input and output. This is potentially more efficient than + inflate() for file i/o applications, in that it avoids copying between the + output and the sliding window by simply making the window itself the output + buffer. inflate() can be faster on modern CPUs when used with large + buffers. inflateBack() trusts the application to not change the output + buffer passed by the output function, at least until inflateBack() returns. + + inflateBackInit() must be called first to allocate the internal state + and to initialize the state with the user-provided window buffer. + inflateBack() may then be used multiple times to inflate a complete, raw + deflate stream with each call. inflateBackEnd() is then called to free the + allocated state. + + A raw deflate stream is one with no zlib or gzip header or trailer. + This routine would normally be used in a utility that reads zip or gzip + files and writes out uncompressed files. The utility would decode the + header and process the trailer on its own, hence this routine expects only + the raw deflate stream to decompress. This is different from the normal + behavior of inflate(), which expects either a zlib or gzip header and + trailer around the deflate stream. + + inflateBack() uses two subroutines supplied by the caller that are then + called by inflateBack() for input and output. inflateBack() calls those + routines until it reads a complete deflate stream and writes out all of the + uncompressed data, or until it encounters an error. The function's + parameters and return types are defined above in the in_func and out_func + typedefs. inflateBack() will call in(in_desc, &buf) which should return the + number of bytes of provided input, and a pointer to that input in buf. If + there is no input available, in() must return zero--buf is ignored in that + case--and inflateBack() will return a buffer error. inflateBack() will call + out(out_desc, buf, len) to write the uncompressed data buf[0..len-1]. out() + should return zero on success, or non-zero on failure. If out() returns + non-zero, inflateBack() will return with an error. Neither in() nor out() + are permitted to change the contents of the window provided to + inflateBackInit(), which is also the buffer that out() uses to write from. + The length written by out() will be at most the window size. Any non-zero + amount of input may be provided by in(). + + For convenience, inflateBack() can be provided input on the first call by + setting strm->next_in and strm->avail_in. If that input is exhausted, then + in() will be called. Therefore strm->next_in must be initialized before + calling inflateBack(). If strm->next_in is Z_NULL, then in() will be called + immediately for input. If strm->next_in is not Z_NULL, then strm->avail_in + must also be initialized, and then if strm->avail_in is not zero, input will + initially be taken from strm->next_in[0 .. strm->avail_in - 1]. + + The in_desc and out_desc parameters of inflateBack() is passed as the + first parameter of in() and out() respectively when they are called. These + descriptors can be optionally used to pass any information that the caller- + supplied in() and out() functions need to do their job. + + On return, inflateBack() will set strm->next_in and strm->avail_in to + pass back any unused input that was provided by the last in() call. The + return values of inflateBack() can be Z_STREAM_END on success, Z_BUF_ERROR + if in() or out() returned an error, Z_DATA_ERROR if there was a format error + in the deflate stream (in which case strm->msg is set to indicate the nature + of the error), or Z_STREAM_ERROR if the stream was not properly initialized. + In the case of Z_BUF_ERROR, an input or output error can be distinguished + using strm->next_in which will be Z_NULL only if in() returned an error. If + strm->next_in is not Z_NULL, then the Z_BUF_ERROR was due to out() returning + non-zero. (in() will always be called before out(), so strm->next_in is + assured to be defined if out() returns non-zero.) Note that inflateBack() + cannot return Z_OK. +*/ + +ZEXTERN int ZEXPORT inflateBackEnd OF((z_streamp strm)); +/* + All memory allocated by inflateBackInit() is freed. + + inflateBackEnd() returns Z_OK on success, or Z_STREAM_ERROR if the stream + state was inconsistent. +*/ + +ZEXTERN uLong ZEXPORT zlibCompileFlags OF((void)); +/* Return flags indicating compile-time options. + + Type sizes, two bits each, 00 = 16 bits, 01 = 32, 10 = 64, 11 = other: + 1.0: size of uInt + 3.2: size of uLong + 5.4: size of voidpf (pointer) + 7.6: size of z_off_t + + Compiler, assembler, and debug options: + 8: DEBUG + 9: ASMV or ASMINF -- use ASM code + 10: ZLIB_WINAPI -- exported functions use the WINAPI calling convention + 11: 0 (reserved) + + One-time table building (smaller code, but not thread-safe if true): + 12: BUILDFIXED -- build static block decoding tables when needed + 13: DYNAMIC_CRC_TABLE -- build CRC calculation tables when needed + 14,15: 0 (reserved) + + Library content (indicates missing functionality): + 16: NO_GZCOMPRESS -- gz* functions cannot compress (to avoid linking + deflate code when not needed) + 17: NO_GZIP -- deflate can't write gzip streams, and inflate can't detect + and decode gzip streams (to avoid linking crc code) + 18-19: 0 (reserved) + + Operation variations (changes in library functionality): + 20: PKZIP_BUG_WORKAROUND -- slightly more permissive inflate + 21: FASTEST -- deflate algorithm with only one, lowest compression level + 22,23: 0 (reserved) + + The sprintf variant used by gzprintf (zero is best): + 24: 0 = vs*, 1 = s* -- 1 means limited to 20 arguments after the format + 25: 0 = *nprintf, 1 = *printf -- 1 means gzprintf() not secure! + 26: 0 = returns value, 1 = void -- 1 means inferred string length returned + + Remainder: + 27-31: 0 (reserved) + */ + +#ifndef Z_SOLO + + /* utility functions */ + +/* + The following utility functions are implemented on top of the basic + stream-oriented functions. To simplify the interface, some default options + are assumed (compression level and memory usage, standard memory allocation + functions). The source code of these utility functions can be modified if + you need special options. +*/ + +ZEXTERN int ZEXPORT compress OF((Bytef *dest, uLongf *destLen, + const Bytef *source, uLong sourceLen)); +/* + Compresses the source buffer into the destination buffer. sourceLen is + the byte length of the source buffer. Upon entry, destLen is the total size + of the destination buffer, which must be at least the value returned by + compressBound(sourceLen). Upon exit, destLen is the actual size of the + compressed buffer. + + compress returns Z_OK if success, Z_MEM_ERROR if there was not + enough memory, Z_BUF_ERROR if there was not enough room in the output + buffer. +*/ + +ZEXTERN int ZEXPORT compress2 OF((Bytef *dest, uLongf *destLen, + const Bytef *source, uLong sourceLen, + int level)); +/* + Compresses the source buffer into the destination buffer. The level + parameter has the same meaning as in deflateInit. sourceLen is the byte + length of the source buffer. Upon entry, destLen is the total size of the + destination buffer, which must be at least the value returned by + compressBound(sourceLen). Upon exit, destLen is the actual size of the + compressed buffer. + + compress2 returns Z_OK if success, Z_MEM_ERROR if there was not enough + memory, Z_BUF_ERROR if there was not enough room in the output buffer, + Z_STREAM_ERROR if the level parameter is invalid. +*/ + +ZEXTERN uLong ZEXPORT compressBound OF((uLong sourceLen)); +/* + compressBound() returns an upper bound on the compressed size after + compress() or compress2() on sourceLen bytes. It would be used before a + compress() or compress2() call to allocate the destination buffer. +*/ + +ZEXTERN int ZEXPORT uncompress OF((Bytef *dest, uLongf *destLen, + const Bytef *source, uLong sourceLen)); +/* + Decompresses the source buffer into the destination buffer. sourceLen is + the byte length of the source buffer. Upon entry, destLen is the total size + of the destination buffer, which must be large enough to hold the entire + uncompressed data. (The size of the uncompressed data must have been saved + previously by the compressor and transmitted to the decompressor by some + mechanism outside the scope of this compression library.) Upon exit, destLen + is the actual size of the uncompressed buffer. + + uncompress returns Z_OK if success, Z_MEM_ERROR if there was not + enough memory, Z_BUF_ERROR if there was not enough room in the output + buffer, or Z_DATA_ERROR if the input data was corrupted or incomplete. In + the case where there is not enough room, uncompress() will fill the output + buffer with the uncompressed data up to that point. +*/ + + /* gzip file access functions */ + +/* + This library supports reading and writing files in gzip (.gz) format with + an interface similar to that of stdio, using the functions that start with + "gz". The gzip format is different from the zlib format. gzip is a gzip + wrapper, documented in RFC 1952, wrapped around a deflate stream. +*/ + +typedef struct gzFile_s *gzFile; /* semi-opaque gzip file descriptor */ + +/* +ZEXTERN gzFile ZEXPORT gzopen OF((const char *path, const char *mode)); + + Opens a gzip (.gz) file for reading or writing. The mode parameter is as + in fopen ("rb" or "wb") but can also include a compression level ("wb9") or + a strategy: 'f' for filtered data as in "wb6f", 'h' for Huffman-only + compression as in "wb1h", 'R' for run-length encoding as in "wb1R", or 'F' + for fixed code compression as in "wb9F". (See the description of + deflateInit2 for more information about the strategy parameter.) 'T' will + request transparent writing or appending with no compression and not using + the gzip format. + + "a" can be used instead of "w" to request that the gzip stream that will + be written be appended to the file. "+" will result in an error, since + reading and writing to the same gzip file is not supported. The addition of + "x" when writing will create the file exclusively, which fails if the file + already exists. On systems that support it, the addition of "e" when + reading or writing will set the flag to close the file on an execve() call. + + These functions, as well as gzip, will read and decode a sequence of gzip + streams in a file. The append function of gzopen() can be used to create + such a file. (Also see gzflush() for another way to do this.) When + appending, gzopen does not test whether the file begins with a gzip stream, + nor does it look for the end of the gzip streams to begin appending. gzopen + will simply append a gzip stream to the existing file. + + gzopen can be used to read a file which is not in gzip format; in this + case gzread will directly read from the file without decompression. When + reading, this will be detected automatically by looking for the magic two- + byte gzip header. + + gzopen returns NULL if the file could not be opened, if there was + insufficient memory to allocate the gzFile state, or if an invalid mode was + specified (an 'r', 'w', or 'a' was not provided, or '+' was provided). + errno can be checked to determine if the reason gzopen failed was that the + file could not be opened. +*/ + +ZEXTERN gzFile ZEXPORT gzdopen OF((int fd, const char *mode)); +/* + gzdopen associates a gzFile with the file descriptor fd. File descriptors + are obtained from calls like open, dup, creat, pipe or fileno (if the file + has been previously opened with fopen). The mode parameter is as in gzopen. + + The next call of gzclose on the returned gzFile will also close the file + descriptor fd, just like fclose(fdopen(fd, mode)) closes the file descriptor + fd. If you want to keep fd open, use fd = dup(fd_keep); gz = gzdopen(fd, + mode);. The duplicated descriptor should be saved to avoid a leak, since + gzdopen does not close fd if it fails. If you are using fileno() to get the + file descriptor from a FILE *, then you will have to use dup() to avoid + double-close()ing the file descriptor. Both gzclose() and fclose() will + close the associated file descriptor, so they need to have different file + descriptors. + + gzdopen returns NULL if there was insufficient memory to allocate the + gzFile state, if an invalid mode was specified (an 'r', 'w', or 'a' was not + provided, or '+' was provided), or if fd is -1. The file descriptor is not + used until the next gz* read, write, seek, or close operation, so gzdopen + will not detect if fd is invalid (unless fd is -1). +*/ + +ZEXTERN int ZEXPORT gzbuffer OF((gzFile file, unsigned size)); +/* + Set the internal buffer size used by this library's functions. The + default buffer size is 8192 bytes. This function must be called after + gzopen() or gzdopen(), and before any other calls that read or write the + file. The buffer memory allocation is always deferred to the first read or + write. Two buffers are allocated, either both of the specified size when + writing, or one of the specified size and the other twice that size when + reading. A larger buffer size of, for example, 64K or 128K bytes will + noticeably increase the speed of decompression (reading). + + The new buffer size also affects the maximum length for gzprintf(). + + gzbuffer() returns 0 on success, or -1 on failure, such as being called + too late. +*/ + +ZEXTERN int ZEXPORT gzsetparams OF((gzFile file, int level, int strategy)); +/* + Dynamically update the compression level or strategy. See the description + of deflateInit2 for the meaning of these parameters. + + gzsetparams returns Z_OK if success, or Z_STREAM_ERROR if the file was not + opened for writing. +*/ + +ZEXTERN int ZEXPORT gzread OF((gzFile file, voidp buf, unsigned len)); +/* + Reads the given number of uncompressed bytes from the compressed file. If + the input file is not in gzip format, gzread copies the given number of + bytes into the buffer directly from the file. + + After reaching the end of a gzip stream in the input, gzread will continue + to read, looking for another gzip stream. Any number of gzip streams may be + concatenated in the input file, and will all be decompressed by gzread(). + If something other than a gzip stream is encountered after a gzip stream, + that remaining trailing garbage is ignored (and no error is returned). + + gzread can be used to read a gzip file that is being concurrently written. + Upon reaching the end of the input, gzread will return with the available + data. If the error code returned by gzerror is Z_OK or Z_BUF_ERROR, then + gzclearerr can be used to clear the end of file indicator in order to permit + gzread to be tried again. Z_OK indicates that a gzip stream was completed + on the last gzread. Z_BUF_ERROR indicates that the input file ended in the + middle of a gzip stream. Note that gzread does not return -1 in the event + of an incomplete gzip stream. This error is deferred until gzclose(), which + will return Z_BUF_ERROR if the last gzread ended in the middle of a gzip + stream. Alternatively, gzerror can be used before gzclose to detect this + case. + + gzread returns the number of uncompressed bytes actually read, less than + len for end of file, or -1 for error. +*/ + +ZEXTERN int ZEXPORT gzwrite OF((gzFile file, + voidpc buf, unsigned len)); +/* + Writes the given number of uncompressed bytes into the compressed file. + gzwrite returns the number of uncompressed bytes written or 0 in case of + error. +*/ + +ZEXTERN int ZEXPORTVA gzprintf Z_ARG((gzFile file, const char *format, ...)); +/* + Converts, formats, and writes the arguments to the compressed file under + control of the format string, as in fprintf. gzprintf returns the number of + uncompressed bytes actually written, or 0 in case of error. The number of + uncompressed bytes written is limited to 8191, or one less than the buffer + size given to gzbuffer(). The caller should assure that this limit is not + exceeded. If it is exceeded, then gzprintf() will return an error (0) with + nothing written. In this case, there may also be a buffer overflow with + unpredictable consequences, which is possible only if zlib was compiled with + the insecure functions sprintf() or vsprintf() because the secure snprintf() + or vsnprintf() functions were not available. This can be determined using + zlibCompileFlags(). +*/ + +ZEXTERN int ZEXPORT gzputs OF((gzFile file, const char *s)); +/* + Writes the given null-terminated string to the compressed file, excluding + the terminating null character. + + gzputs returns the number of characters written, or -1 in case of error. +*/ + +ZEXTERN char * ZEXPORT gzgets OF((gzFile file, char *buf, int len)); +/* + Reads bytes from the compressed file until len-1 characters are read, or a + newline character is read and transferred to buf, or an end-of-file + condition is encountered. If any characters are read or if len == 1, the + string is terminated with a null character. If no characters are read due + to an end-of-file or len < 1, then the buffer is left untouched. + + gzgets returns buf which is a null-terminated string, or it returns NULL + for end-of-file or in case of error. If there was an error, the contents at + buf are indeterminate. +*/ + +ZEXTERN int ZEXPORT gzputc OF((gzFile file, int c)); +/* + Writes c, converted to an unsigned char, into the compressed file. gzputc + returns the value that was written, or -1 in case of error. +*/ + +ZEXTERN int ZEXPORT gzgetc OF((gzFile file)); +/* + Reads one byte from the compressed file. gzgetc returns this byte or -1 + in case of end of file or error. This is implemented as a macro for speed. + As such, it does not do all of the checking the other functions do. I.e. + it does not check to see if file is NULL, nor whether the structure file + points to has been clobbered or not. +*/ + +ZEXTERN int ZEXPORT gzungetc OF((int c, gzFile file)); +/* + Push one character back onto the stream to be read as the first character + on the next read. At least one character of push-back is allowed. + gzungetc() returns the character pushed, or -1 on failure. gzungetc() will + fail if c is -1, and may fail if a character has been pushed but not read + yet. If gzungetc is used immediately after gzopen or gzdopen, at least the + output buffer size of pushed characters is allowed. (See gzbuffer above.) + The pushed character will be discarded if the stream is repositioned with + gzseek() or gzrewind(). +*/ + +ZEXTERN int ZEXPORT gzflush OF((gzFile file, int flush)); +/* + Flushes all pending output into the compressed file. The parameter flush + is as in the deflate() function. The return value is the zlib error number + (see function gzerror below). gzflush is only permitted when writing. + + If the flush parameter is Z_FINISH, the remaining data is written and the + gzip stream is completed in the output. If gzwrite() is called again, a new + gzip stream will be started in the output. gzread() is able to read such + concatented gzip streams. + + gzflush should be called only when strictly necessary because it will + degrade compression if called too often. +*/ + +/* +ZEXTERN z_off_t ZEXPORT gzseek OF((gzFile file, + z_off_t offset, int whence)); + + Sets the starting position for the next gzread or gzwrite on the given + compressed file. The offset represents a number of bytes in the + uncompressed data stream. The whence parameter is defined as in lseek(2); + the value SEEK_END is not supported. + + If the file is opened for reading, this function is emulated but can be + extremely slow. If the file is opened for writing, only forward seeks are + supported; gzseek then compresses a sequence of zeroes up to the new + starting position. + + gzseek returns the resulting offset location as measured in bytes from + the beginning of the uncompressed stream, or -1 in case of error, in + particular if the file is opened for writing and the new starting position + would be before the current position. +*/ + +ZEXTERN int ZEXPORT gzrewind OF((gzFile file)); +/* + Rewinds the given file. This function is supported only for reading. + + gzrewind(file) is equivalent to (int)gzseek(file, 0L, SEEK_SET) +*/ + +/* +ZEXTERN z_off_t ZEXPORT gztell OF((gzFile file)); + + Returns the starting position for the next gzread or gzwrite on the given + compressed file. This position represents a number of bytes in the + uncompressed data stream, and is zero when starting, even if appending or + reading a gzip stream from the middle of a file using gzdopen(). + + gztell(file) is equivalent to gzseek(file, 0L, SEEK_CUR) +*/ + +/* +ZEXTERN z_off_t ZEXPORT gzoffset OF((gzFile file)); + + Returns the current offset in the file being read or written. This offset + includes the count of bytes that precede the gzip stream, for example when + appending or when using gzdopen() for reading. When reading, the offset + does not include as yet unused buffered input. This information can be used + for a progress indicator. On error, gzoffset() returns -1. +*/ + +ZEXTERN int ZEXPORT gzeof OF((gzFile file)); +/* + Returns true (1) if the end-of-file indicator has been set while reading, + false (0) otherwise. Note that the end-of-file indicator is set only if the + read tried to go past the end of the input, but came up short. Therefore, + just like feof(), gzeof() may return false even if there is no more data to + read, in the event that the last read request was for the exact number of + bytes remaining in the input file. This will happen if the input file size + is an exact multiple of the buffer size. + + If gzeof() returns true, then the read functions will return no more data, + unless the end-of-file indicator is reset by gzclearerr() and the input file + has grown since the previous end of file was detected. +*/ + +ZEXTERN int ZEXPORT gzdirect OF((gzFile file)); +/* + Returns true (1) if file is being copied directly while reading, or false + (0) if file is a gzip stream being decompressed. + + If the input file is empty, gzdirect() will return true, since the input + does not contain a gzip stream. + + If gzdirect() is used immediately after gzopen() or gzdopen() it will + cause buffers to be allocated to allow reading the file to determine if it + is a gzip file. Therefore if gzbuffer() is used, it should be called before + gzdirect(). + + When writing, gzdirect() returns true (1) if transparent writing was + requested ("wT" for the gzopen() mode), or false (0) otherwise. (Note: + gzdirect() is not needed when writing. Transparent writing must be + explicitly requested, so the application already knows the answer. When + linking statically, using gzdirect() will include all of the zlib code for + gzip file reading and decompression, which may not be desired.) +*/ + +ZEXTERN int ZEXPORT gzclose OF((gzFile file)); +/* + Flushes all pending output if necessary, closes the compressed file and + deallocates the (de)compression state. Note that once file is closed, you + cannot call gzerror with file, since its structures have been deallocated. + gzclose must not be called more than once on the same file, just as free + must not be called more than once on the same allocation. + + gzclose will return Z_STREAM_ERROR if file is not valid, Z_ERRNO on a + file operation error, Z_MEM_ERROR if out of memory, Z_BUF_ERROR if the + last read ended in the middle of a gzip stream, or Z_OK on success. +*/ + +ZEXTERN int ZEXPORT gzclose_r OF((gzFile file)); +ZEXTERN int ZEXPORT gzclose_w OF((gzFile file)); +/* + Same as gzclose(), but gzclose_r() is only for use when reading, and + gzclose_w() is only for use when writing or appending. The advantage to + using these instead of gzclose() is that they avoid linking in zlib + compression or decompression code that is not used when only reading or only + writing respectively. If gzclose() is used, then both compression and + decompression code will be included the application when linking to a static + zlib library. +*/ + +ZEXTERN const char * ZEXPORT gzerror OF((gzFile file, int *errnum)); +/* + Returns the error message for the last error which occurred on the given + compressed file. errnum is set to zlib error number. If an error occurred + in the file system and not in the compression library, errnum is set to + Z_ERRNO and the application may consult errno to get the exact error code. + + The application must not modify the returned string. Future calls to + this function may invalidate the previously returned string. If file is + closed, then the string previously returned by gzerror will no longer be + available. + + gzerror() should be used to distinguish errors from end-of-file for those + functions above that do not distinguish those cases in their return values. +*/ + +ZEXTERN void ZEXPORT gzclearerr OF((gzFile file)); +/* + Clears the error and end-of-file flags for file. This is analogous to the + clearerr() function in stdio. This is useful for continuing to read a gzip + file that is being written concurrently. +*/ + +#endif /* !Z_SOLO */ + + /* checksum functions */ + +/* + These functions are not related to compression but are exported + anyway because they might be useful in applications using the compression + library. +*/ + +ZEXTERN uLong ZEXPORT adler32 OF((uLong adler, const Bytef *buf, uInt len)); +/* + Update a running Adler-32 checksum with the bytes buf[0..len-1] and + return the updated checksum. If buf is Z_NULL, this function returns the + required initial value for the checksum. + + An Adler-32 checksum is almost as reliable as a CRC32 but can be computed + much faster. + + Usage example: + + uLong adler = adler32(0L, Z_NULL, 0); + + while (read_buffer(buffer, length) != EOF) { + adler = adler32(adler, buffer, length); + } + if (adler != original_adler) error(); +*/ + +/* +ZEXTERN uLong ZEXPORT adler32_combine OF((uLong adler1, uLong adler2, + z_off_t len2)); + + Combine two Adler-32 checksums into one. For two sequences of bytes, seq1 + and seq2 with lengths len1 and len2, Adler-32 checksums were calculated for + each, adler1 and adler2. adler32_combine() returns the Adler-32 checksum of + seq1 and seq2 concatenated, requiring only adler1, adler2, and len2. Note + that the z_off_t type (like off_t) is a signed integer. If len2 is + negative, the result has no meaning or utility. +*/ + +ZEXTERN uLong ZEXPORT crc32 OF((uLong crc, const Bytef *buf, uInt len)); +/* + Update a running CRC-32 with the bytes buf[0..len-1] and return the + updated CRC-32. If buf is Z_NULL, this function returns the required + initial value for the crc. Pre- and post-conditioning (one's complement) is + performed within this function so it shouldn't be done by the application. + + Usage example: + + uLong crc = crc32(0L, Z_NULL, 0); + + while (read_buffer(buffer, length) != EOF) { + crc = crc32(crc, buffer, length); + } + if (crc != original_crc) error(); +*/ + +/* +ZEXTERN uLong ZEXPORT crc32_combine OF((uLong crc1, uLong crc2, z_off_t len2)); + + Combine two CRC-32 check values into one. For two sequences of bytes, + seq1 and seq2 with lengths len1 and len2, CRC-32 check values were + calculated for each, crc1 and crc2. crc32_combine() returns the CRC-32 + check value of seq1 and seq2 concatenated, requiring only crc1, crc2, and + len2. +*/ + + + /* various hacks, don't look :) */ + +/* deflateInit and inflateInit are macros to allow checking the zlib version + * and the compiler's view of z_stream: + */ +ZEXTERN int ZEXPORT deflateInit_ OF((z_streamp strm, int level, + const char *version, int stream_size)); +ZEXTERN int ZEXPORT inflateInit_ OF((z_streamp strm, + const char *version, int stream_size)); +ZEXTERN int ZEXPORT deflateInit2_ OF((z_streamp strm, int level, int method, + int windowBits, int memLevel, + int strategy, const char *version, + int stream_size)); +ZEXTERN int ZEXPORT inflateInit2_ OF((z_streamp strm, int windowBits, + const char *version, int stream_size)); +ZEXTERN int ZEXPORT inflateBackInit_ OF((z_streamp strm, int windowBits, + unsigned char FAR *window, + const char *version, + int stream_size)); +#define deflateInit(strm, level) \ + deflateInit_((strm), (level), ZLIB_VERSION, (int)sizeof(z_stream)) +#define inflateInit(strm) \ + inflateInit_((strm), ZLIB_VERSION, (int)sizeof(z_stream)) +#define deflateInit2(strm, level, method, windowBits, memLevel, strategy) \ + deflateInit2_((strm),(level),(method),(windowBits),(memLevel),\ + (strategy), ZLIB_VERSION, (int)sizeof(z_stream)) +#define inflateInit2(strm, windowBits) \ + inflateInit2_((strm), (windowBits), ZLIB_VERSION, \ + (int)sizeof(z_stream)) +#define inflateBackInit(strm, windowBits, window) \ + inflateBackInit_((strm), (windowBits), (window), \ + ZLIB_VERSION, (int)sizeof(z_stream)) + +#ifndef Z_SOLO + +/* gzgetc() macro and its supporting function and exposed data structure. Note + * that the real internal state is much larger than the exposed structure. + * This abbreviated structure exposes just enough for the gzgetc() macro. The + * user should not mess with these exposed elements, since their names or + * behavior could change in the future, perhaps even capriciously. They can + * only be used by the gzgetc() macro. You have been warned. + */ +struct gzFile_s { + unsigned have; + unsigned char *next; + z_off64_t pos; +}; +ZEXTERN int ZEXPORT gzgetc_ OF((gzFile file)); /* backward compatibility */ +#ifdef Z_PREFIX_SET +# undef z_gzgetc +# define z_gzgetc(g) \ + ((g)->have ? ((g)->have--, (g)->pos++, *((g)->next)++) : gzgetc(g)) +#else +# define gzgetc(g) \ + ((g)->have ? ((g)->have--, (g)->pos++, *((g)->next)++) : gzgetc(g)) +#endif + +/* provide 64-bit offset functions if _LARGEFILE64_SOURCE defined, and/or + * change the regular functions to 64 bits if _FILE_OFFSET_BITS is 64 (if + * both are true, the application gets the *64 functions, and the regular + * functions are changed to 64 bits) -- in case these are set on systems + * without large file support, _LFS64_LARGEFILE must also be true + */ +#ifdef Z_LARGE64 + ZEXTERN gzFile ZEXPORT gzopen64 OF((const char *, const char *)); + ZEXTERN z_off64_t ZEXPORT gzseek64 OF((gzFile, z_off64_t, int)); + ZEXTERN z_off64_t ZEXPORT gztell64 OF((gzFile)); + ZEXTERN z_off64_t ZEXPORT gzoffset64 OF((gzFile)); + ZEXTERN uLong ZEXPORT adler32_combine64 OF((uLong, uLong, z_off64_t)); + ZEXTERN uLong ZEXPORT crc32_combine64 OF((uLong, uLong, z_off64_t)); +#endif + +#if !defined(ZLIB_INTERNAL) && defined(Z_WANT64) +# ifdef Z_PREFIX_SET +# define z_gzopen z_gzopen64 +# define z_gzseek z_gzseek64 +# define z_gztell z_gztell64 +# define z_gzoffset z_gzoffset64 +# define z_adler32_combine z_adler32_combine64 +# define z_crc32_combine z_crc32_combine64 +# else +# define gzopen gzopen64 +# define gzseek gzseek64 +# define gztell gztell64 +# define gzoffset gzoffset64 +# define adler32_combine adler32_combine64 +# define crc32_combine crc32_combine64 +# endif +# ifndef Z_LARGE64 + ZEXTERN gzFile ZEXPORT gzopen64 OF((const char *, const char *)); + ZEXTERN off64_t ZEXPORT gzseek64 OF((gzFile, off64_t, int)); + ZEXTERN off64_t ZEXPORT gztell64 OF((gzFile)); + ZEXTERN z_off64_t ZEXPORT gzoffset64 OF((gzFile)); + ZEXTERN uLong ZEXPORT adler32_combine64 OF((uLong, uLong, off64_t)); + ZEXTERN uLong ZEXPORT crc32_combine64 OF((uLong, uLong, off64_t)); +# endif +#else + ZEXTERN gzFile ZEXPORT gzopen OF((const char *, const char *)); + ZEXTERN z_off_t ZEXPORT gzseek OF((gzFile, z_off_t, int)); + ZEXTERN z_off_t ZEXPORT gztell OF((gzFile)); + ZEXTERN z_off_t ZEXPORT gzoffset OF((gzFile)); + ZEXTERN uLong ZEXPORT adler32_combine OF((uLong, uLong, z_off_t)); + ZEXTERN uLong ZEXPORT crc32_combine OF((uLong, uLong, z_off_t)); +#endif + +#else /* Z_SOLO */ + + ZEXTERN uLong ZEXPORT adler32_combine OF((uLong, uLong, z_off_t)); + ZEXTERN uLong ZEXPORT crc32_combine OF((uLong, uLong, z_off_t)); + +#endif /* !Z_SOLO */ + +/* hack for buggy compilers */ +#if !defined(ZUTIL_H) && !defined(NO_DUMMY_DECL) + struct internal_state {int dummy;}; +#endif + +/* undocumented functions */ +ZEXTERN const char * ZEXPORT zError OF((int)); +ZEXTERN int ZEXPORT inflateSyncPoint OF((z_streamp)); +ZEXTERN const z_crc_t FAR * ZEXPORT get_crc_table OF((void)); +ZEXTERN int ZEXPORT inflateUndermine OF((z_streamp, int)); +ZEXTERN int ZEXPORT inflateResetKeep OF((z_streamp)); +ZEXTERN int ZEXPORT deflateResetKeep OF((z_streamp)); +#if defined(_WIN32) && !defined(Z_SOLO) +ZEXTERN gzFile ZEXPORT gzopen_w OF((const wchar_t *path, + const char *mode)); +#endif +#if defined(STDC) || defined(Z_HAVE_STDARG_H) +# ifndef Z_SOLO +ZEXTERN int ZEXPORTVA gzvprintf Z_ARG((gzFile file, + const char *format, + va_list va)); +# endif +#endif + +#ifdef __cplusplus +} +#endif + +#endif /* ZLIB_H */ |