From 1a691f101632955a994a0198fc5498b108e97fbc Mon Sep 17 00:00:00 2001 From: Iru Cai Date: Wed, 30 Oct 2019 15:42:15 +0800 Subject: rm include/configs --- include/configs/MPC8308RDB.h | 341 ------------------------------------------- 1 file changed, 341 deletions(-) delete mode 100644 include/configs/MPC8308RDB.h (limited to 'include/configs/MPC8308RDB.h') diff --git a/include/configs/MPC8308RDB.h b/include/configs/MPC8308RDB.h deleted file mode 100644 index 85d7ff6..0000000 --- a/include/configs/MPC8308RDB.h +++ /dev/null @@ -1,341 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. - * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com - * - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 family */ - -#ifdef CONFIG_MMC -#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR -#define CONFIG_SYS_FSL_ESDHC_USE_PIO -#endif - -/* - * On-board devices - * - * TSEC1 is SoC TSEC - * TSEC2 is VSC switch - */ -#define CONFIG_TSEC1 -#define CONFIG_VSC7385_ENET - -/* - * SERDES - */ -#define CONFIG_FSL_SERDES -#define CONFIG_FSL_SERDES1 0xe3000 - -/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 -#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ - | DDRCDR_PZ_LOZ \ - | DDRCDR_NZ_LOZ \ - | DDRCDR_ODT \ - | DDRCDR_Q_DRN) - /* 0x7b880001 */ -/* - * Manually set up DDR parameters - * consist of two chips HY5PS12621BFP-C4 from HYNIX - */ - -#define CONFIG_SYS_DDR_SIZE 128 /* MB */ - -#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ - | CSCONFIG_ODT_RD_NEVER \ - | CSCONFIG_ODT_WR_ONLY_CURRENT \ - | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) - /* 0x80010102 */ -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 -#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ - | (0 << TIMING_CFG0_WRT_SHIFT) \ - | (0 << TIMING_CFG0_RRT_SHIFT) \ - | (0 << TIMING_CFG0_WWT_SHIFT) \ - | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ - | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ - | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ - | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) - /* 0x00220802 */ -#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ - | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \ - | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ - | (5 << TIMING_CFG1_CASLAT_SHIFT) \ - | (6 << TIMING_CFG1_REFREC_SHIFT) \ - | (2 << TIMING_CFG1_WRREC_SHIFT) \ - | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ - | (2 << TIMING_CFG1_WRTORD_SHIFT)) - /* 0x27256222 */ -#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ - | (4 << TIMING_CFG2_CPO_SHIFT) \ - | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ - | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ - | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ - | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ - | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) - /* 0x121048c5 */ -#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \ - | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) - /* 0x03600100 */ -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ - | SDRAM_CFG_SDRAM_TYPE_DDR2 \ - | SDRAM_CFG_DBW_32) - /* 0x43080000 */ - -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ -#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ - | (0x0232 << SDRAM_MODE_SD_SHIFT)) - /* ODT 150ohm CL=3, AL=1 on SDRAM */ -#define CONFIG_SYS_DDR_MODE2 0x00000000 - -/* - * Memory test - */ -#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x07f00000 - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT - -#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ -#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */ - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -/* 127 64KB sectors and 8 8KB top sectors per device */ -#define CONFIG_SYS_MAX_FLASH_SECT 135 - -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -/* - * NAND Flash on the Local Bus - */ -#define CONFIG_SYS_NAND_BASE 0xE0600000 /* 0xE0600000 */ -#define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024) /* 0x00008000 */ - /* 0xFFFF8396 */ - -#ifdef CONFIG_VSC7385_ENET -#define CONFIG_TSEC2 - /* VSC7385 Base address on CS2 */ -#define CONFIG_SYS_VSC7385_BASE 0xF0000000 -#define CONFIG_SYS_VSC7385_SIZE (128 * 1024) /* 0x00020000 */ - /* 0xFFFE09FF */ -/* The flash address and size of the VSC7385 firmware image */ -#define CONFIG_VSC7385_IMAGE 0xFE7FE000 -#define CONFIG_VSC7385_IMAGE_SIZE 8192 -#endif -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } - -/* - * SPI on header J8 - * - * WARNING: enabling this will break TSEC2 (connected to the Vitesse switch) - * due to a pinmux conflict between GPIO9 (SPI chip select )and the TSEC2 pins. - */ -#ifdef CONFIG_MPC8XXX_SPI -#define CONFIG_USE_SPIFLASH -#endif - -/* - * Board info - revision and where boot from - */ -#define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39 - -/* - * Config on-board RTC - */ -#define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_SYS_PCIE1_BASE 0xA0000000 -#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 -#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 -#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 -#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 - -/* enable PCIE clock */ -#define CONFIG_SYS_SCCR_PCIEXP1CM 1 - -#define CONFIG_PCI_INDIRECT_BRIDGE -#define CONFIG_PCIE - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ -#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 - -/* - * TSEC - */ -#define CONFIG_SYS_TSEC1_OFFSET 0x24000 -#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) -#define CONFIG_SYS_TSEC2_OFFSET 0x25000 -#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) - -/* - * TSEC ethernet configuration - */ -#define CONFIG_TSEC1_NAME "eTSEC0" -#define CONFIG_TSEC2_NAME "eTSEC1" -#define TSEC1_PHY_ADDR 2 -#define TSEC2_PHY_ADDR 1 -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC1_FLAGS TSEC_GIGABIT -#define TSEC2_FLAGS TSEC_GIGABIT - -/* Options are: eTSEC[0-1] */ -#define CONFIG_ETHPRIME "eTSEC0" - -/* - * Environment - */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) -#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * Command line configuration. - */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ - -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -/* - * Environment Configuration - */ - -#define CONFIG_ENV_OVERWRITE - -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#endif - -#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ - - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consoledev=ttyS0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs}" \ - " console=${consoledev},${baudrate}\0" \ - "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ - "addmisc=setenv bootargs ${bootargs}\0" \ - "kernel_addr=FE080000\0" \ - "fdt_addr=FE280000\0" \ - "ramdisk_addr=FE290000\0" \ - "u-boot=mpc8308rdb/u-boot.bin\0" \ - "kernel_addr_r=1000000\0" \ - "fdt_addr_r=C00000\0" \ - "hostname=mpc8308rdb\0" \ - "bootfile=mpc8308rdb/uImage\0" \ - "fdtfile=mpc8308rdb/mpc8308rdb.dtb\0" \ - "rootpath=/opt/eldk-4.2/ppc_6xx\0" \ - "flash_self=run ramargs addip addtty addmtd addmisc;" \ - "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ - "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ - "tftp ${fdt_addr_r} ${fdtfile};" \ - "run nfsargs addip addtty addmtd addmisc;" \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "bootcmd=run flash_self\0" \ - "load=tftp ${loadaddr} ${u-boot}\0" \ - "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ - " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\ - " +${filesize};cp.b ${fileaddr} " \ - __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ - "upd=run load update\0" \ - -#endif /* __CONFIG_H */ -- cgit v1.2.3