From 1a691f101632955a994a0198fc5498b108e97fbc Mon Sep 17 00:00:00 2001 From: Iru Cai Date: Wed, 30 Oct 2019 15:42:15 +0800 Subject: rm include/configs --- include/configs/MPC8313ERDB_NOR.h | 377 -------------------------------------- 1 file changed, 377 deletions(-) delete mode 100644 include/configs/MPC8313ERDB_NOR.h (limited to 'include/configs/MPC8313ERDB_NOR.h') diff --git a/include/configs/MPC8313ERDB_NOR.h b/include/configs/MPC8313ERDB_NOR.h deleted file mode 100644 index ff8dedf..0000000 --- a/include/configs/MPC8313ERDB_NOR.h +++ /dev/null @@ -1,377 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) Freescale Semiconductor, Inc. 2006, 2010. - */ -/* - * mpc8313epb board configuration file - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 - -#ifndef CONFIG_SYS_MONITOR_BASE -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#endif - -#define CONFIG_PCI_INDIRECT_BRIDGE -#define CONFIG_FSL_ELBC 1 - -/* - * On-board devices - * - * TSEC1 is VSC switch - * TSEC2 is SoC TSEC - */ -#define CONFIG_VSC7385_ENET -#define CONFIG_TSEC2 - -#define CONFIG_SYS_MEMTEST_START 0x00001000 -#define CONFIG_SYS_MEMTEST_END 0x07f00000 - -/* Early revs of this board will lock up hard when attempting - * to access the PMC registers, unless a JTAG debugger is - * connected, or some resistor modifications are made. - */ -#define CONFIG_SYS_8313ERDB_BROKEN_PMC 1 - -/* - * Device configurations - */ - -/* Vitesse 7385 */ - -#ifdef CONFIG_VSC7385_ENET - -#define CONFIG_TSEC1 - -/* The flash address and size of the VSC7385 firmware image */ -#define CONFIG_VSC7385_IMAGE 0xFE7FE000 -#define CONFIG_VSC7385_IMAGE_SIZE 8192 - -#endif - -/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory*/ - -/* - * Manually set up DDR parameters, as this board does not - * seem to have the SPD connected to I2C. - */ -#define CONFIG_SYS_DDR_SIZE 128 /* MB */ -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ - | CSCONFIG_ODT_RD_NEVER \ - | CSCONFIG_ODT_WR_ONLY_CURRENT \ - | CSCONFIG_ROW_BIT_13 \ - | CSCONFIG_COL_BIT_10) - /* 0x80010102 */ - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 -#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ - | (0 << TIMING_CFG0_WRT_SHIFT) \ - | (0 << TIMING_CFG0_RRT_SHIFT) \ - | (0 << TIMING_CFG0_WWT_SHIFT) \ - | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ - | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ - | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ - | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) - /* 0x00220802 */ -#define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \ - | (8 << TIMING_CFG1_ACTTOPRE_SHIFT) \ - | (3 << TIMING_CFG1_ACTTORW_SHIFT) \ - | (5 << TIMING_CFG1_CASLAT_SHIFT) \ - | (10 << TIMING_CFG1_REFREC_SHIFT) \ - | (3 << TIMING_CFG1_WRREC_SHIFT) \ - | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ - | (2 << TIMING_CFG1_WRTORD_SHIFT)) - /* 0x3835a322 */ -#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ - | (5 << TIMING_CFG2_CPO_SHIFT) \ - | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ - | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ - | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ - | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ - | (6 << TIMING_CFG2_FOUR_ACT_SHIFT)) - /* 0x129048c6 */ /* P9-45,may need tuning */ -#define CONFIG_SYS_DDR_INTERVAL ((1296 << SDRAM_INTERVAL_REFINT_SHIFT) \ - | (1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) - /* 0x05100500 */ -#if defined(CONFIG_DDR_2T_TIMING) -#define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN \ - | SDRAM_CFG_SDRAM_TYPE_DDR2 \ - | SDRAM_CFG_DBW_32 \ - | SDRAM_CFG_2T_EN) - /* 0x43088000 */ -#else -#define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN \ - | SDRAM_CFG_SDRAM_TYPE_DDR2 \ - | SDRAM_CFG_DBW_32) - /* 0x43080000 */ -#endif -#define CONFIG_SYS_SDRAM_CFG2 0x00401000 -/* set burst length to 8 for 32-bit data path */ -#define CONFIG_SYS_DDR_MODE ((0x4448 << SDRAM_MODE_ESD_SHIFT) \ - | (0x0632 << SDRAM_MODE_SD_SHIFT)) - /* 0x44480632 */ -#define CONFIG_SYS_DDR_MODE_2 0x8000C000 - -#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 - /*0x02000000*/ -#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ - | DDRCDR_PZ_NOMZ \ - | DDRCDR_NZ_NOMZ \ - | DDRCDR_M_ODR) - -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */ -#define CONFIG_SYS_FLASH_SIZE 8 /* flash size in MB */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ -#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 135 /* sectors per device */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) && \ - !defined(CONFIG_SPL_BUILD) -#define CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ - -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ - -/* drivers/mtd/nand/nand.c */ -#define CONFIG_SYS_NAND_BASE 0xE2800000 - -#define CONFIG_MTD_PARTITION - -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_NAND_FSL_ELBC 1 -#define CONFIG_SYS_NAND_BLOCK_SIZE 16384 -#define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024) - -/* Still needed for spl_minimal.c */ -#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR1_PRELIM -#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR1_PRELIM - -/* local bus write LED / read status buffer (BCSR) mapping */ -#define CONFIG_SYS_BCSR_ADDR 0xFA000000 -#define CONFIG_SYS_BCSR_SIZE (32 * 1024) /* 0x00008000 */ - /* map at 0xFA000000 on LCS3 */ -/* Vitesse 7385 */ - -#ifdef CONFIG_VSC7385_ENET - - /* VSC7385 Base address on LCS2 */ -#define CONFIG_SYS_VSC7385_BASE 0xF0000000 -#define CONFIG_SYS_VSC7385_SIZE (128 * 1024) /* 0x00020000 */ - - -#endif - -#define CONFIG_MPC83XX_GPIO 1 - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE -#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 -#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE -#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ - -/* - * TSEC - */ - -#define CONFIG_GMII /* MII PHY management */ - -#ifdef CONFIG_TSEC1 -#define CONFIG_HAS_ETH0 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_SYS_TSEC1_OFFSET 0x24000 -#define TSEC1_PHY_ADDR 0x1c -#define TSEC1_FLAGS TSEC_GIGABIT -#define TSEC1_PHYIDX 0 -#endif - -#ifdef CONFIG_TSEC2 -#define CONFIG_HAS_ETH1 -#define CONFIG_TSEC2_NAME "TSEC1" -#define CONFIG_SYS_TSEC2_OFFSET 0x25000 -#define TSEC2_PHY_ADDR 4 -#define TSEC2_FLAGS TSEC_GIGABIT -#define TSEC2_PHYIDX 0 -#endif - -/* Options are: TSEC[0-1] */ -#define CONFIG_ETHPRIME "TSEC1" - -/* - * Configure on-board RTC - */ -#define CONFIG_RTC_DS1337 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -/* - * Environment - */ -#if !defined(CONFIG_SYS_RAMBOOT) - #define CONFIG_ENV_ADDR \ - (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) - #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ - #define CONFIG_ENV_SIZE 0x2000 - -/* Address and size of Redundant Environment Sector */ -#else - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) - #define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * Command line configuration. - */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ - - /* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ - /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ - -#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)) - -/* System IO Config */ -#define CONFIG_SYS_SICRH (SICRH_TSOBI1 | SICRH_TSOBI2) /* RGMII */ - /* Enable Internal USB Phy and GPIO on LCD Connector */ -#define CONFIG_SYS_SICRL (SICRL_USBDR_10 | SICRL_LBC) - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_NETDEV "eth1" - -#define CONFIG_HOSTNAME "mpc8313erdb" -#define CONFIG_ROOTPATH "/nfs/root/path" -#define CONFIG_BOOTFILE "uImage" - /* U-Boot image on TFTP server */ -#define CONFIG_UBOOTPATH "u-boot.bin" -#define CONFIG_FDTFILE "mpc8313erdb.dtb" - - /* default location for tftp and bootm */ -#define CONFIG_LOADADDR 800000 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=" CONFIG_NETDEV "\0" \ - "ethprime=TSEC1\0" \ - "uboot=" CONFIG_UBOOTPATH "\0" \ - "tftpflash=tftpboot $loadaddr $uboot; " \ - "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize; " \ - "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize\0" \ - "fdtaddr=780000\0" \ - "fdtfile=" CONFIG_FDTFILE "\0" \ - "console=ttyS0\0" \ - "setbootargs=setenv bootargs " \ - "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \ - "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"\ - "$netdev:off " \ - "root=$rootdev rw console=$console,$baudrate $othbootargs\0" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv rootdev /dev/nfs;" \ - "run setbootargs;" \ - "run setipargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv rootdev /dev/ram;" \ - "run setbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#endif /* __CONFIG_H */ -- cgit v1.2.3