From 1a691f101632955a994a0198fc5498b108e97fbc Mon Sep 17 00:00:00 2001 From: Iru Cai Date: Wed, 30 Oct 2019 15:42:15 +0800 Subject: rm include/configs --- include/configs/astro_mcf5373l.h | 297 --------------------------------------- 1 file changed, 297 deletions(-) delete mode 100644 include/configs/astro_mcf5373l.h (limited to 'include/configs/astro_mcf5373l.h') diff --git a/include/configs/astro_mcf5373l.h b/include/configs/astro_mcf5373l.h deleted file mode 100644 index 2e7fbfb..0000000 --- a/include/configs/astro_mcf5373l.h +++ /dev/null @@ -1,297 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Configuration settings for the Sentec Cobra Board. - * - * (C) Copyright 2003 Josef Baumgartner - */ - -/* - * configuration for ASTRO "Urmel" board. - * Originating from Cobra5272 configuration, messed up by - * Wolfgang Wegner - * Please do not bother the original author with bug reports - * concerning this file. - */ - -#ifndef _CONFIG_ASTRO_MCF5373L_H -#define _CONFIG_ASTRO_MCF5373L_H - -#include - -/* - * set the card type to actually compile for; either of - * the possibilities listed below has to be used! - */ -#define CONFIG_ASTRO_V532 1 - -#if CONFIG_ASTRO_V532 -#define ASTRO_ID 0xF8 -#elif CONFIG_ASTRO_V512 -#define ASTRO_ID 0xFA -#elif CONFIG_ASTRO_TWIN7S2 -#define ASTRO_ID 0xF9 -#elif CONFIG_ASTRO_V912 -#define ASTRO_ID 0xFC -#elif CONFIG_ASTRO_COFDMDUOS2 -#define ASTRO_ID 0xFB -#else -#error No card type defined! -#endif - -/* Command line configuration */ -/* - * CONFIG_RAM defines if u-boot is loaded via BDM (or started from - * a different bootloader that has already performed RAM setup) or - * started directly from flash, which is the regular case for production - * boards. - */ -#ifdef CONFIG_RAM -#define CONFIG_MONITOR_IS_IN_RAM -#define ENABLE_JFFS 0 -#else -#define ENABLE_JFFS 1 -#endif - -#define CONFIG_MCFRTC -#undef RTC_DEBUG - -/* Timer */ -#define CONFIG_MCFTMR -#undef CONFIG_MCFPIT - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 80000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 -#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR - -/* - * Defines processor clock - important for correct timings concerning serial - * interface etc. - */ - -#define CONFIG_SYS_CLK 80000000 -#define CONFIG_SYS_CPU_CLK (CONFIG_SYS_CLK * 3) -#define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */ - -#define CONFIG_SYS_CORE_SRAM_SIZE 0x8000 -#define CONFIG_SYS_CORE_SRAM 0x80000000 - -#define CONFIG_SYS_UNIFY_CACHE - -/* - * Define baudrate for UART1 (console output, tftp, ...) - * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud - * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected - * in u-boot command interface - */ - -#define CONFIG_MCFUART -#define CONFIG_SYS_UART_PORT (2) -#define CONFIG_SYS_UART2_ALT3_GPIO - -/* - * Watchdog configuration; Watchdog is disabled for running from RAM - * and set to highest possible value else. Beware there is no check - * in the watchdog code to validate the timeout value set here! - */ - -#ifndef CONFIG_MONITOR_IS_IN_RAM -#define CONFIG_WATCHDOG -#define CONFIG_WATCHDOG_TIMEOUT 3355 /* timeout in milliseconds */ -#endif - -/* - * Configuration for environment - * Environment is located in the last sector of the flash - */ - -#ifndef CONFIG_MONITOR_IS_IN_RAM -#define CONFIG_ENV_OFFSET 0x1FF8000 -#define CONFIG_ENV_SECT_SIZE 0x8000 -#else -/* - * environment in RAM - This is used to use a single PC-based application - * to load an image, load U-Boot, load an environment and then start U-Boot - * to execute the commands from the environment. Feedback is done via setting - * and reading memory locations. - */ -#define CONFIG_ENV_ADDR 0x40060000 -#define CONFIG_ENV_SECT_SIZE 0x8000 -#endif - -/* here we put our FPGA configuration... */ - -/* Define user parameters that have to be customized most likely */ - -/* AUTOBOOT settings - booting images automatically by u-boot after power on */ - -/* - * The following settings will be contained in the environment block ; if you - * want to use a neutral environment all those settings can be manually set in - * u-boot: 'set' command - */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "loaderversion=11\0" \ - "card_id="__stringify(ASTRO_ID)"\0" \ - "alterafile=0\0" \ - "xilinxfile=0\0" \ - "xilinxload=imxtract 0x540000 $xilinxfile 0x41000000&&"\ - "fpga load 0 0x41000000 $filesize\0" \ - "alteraload=imxtract 0x6c0000 $alterafile 0x41000000&&"\ - "fpga load 1 0x41000000 $filesize\0" \ - "env_default=1\0" \ - "env_check=if test $env_default -eq 1;"\ - " then setenv env_default 0;saveenv;fi\0" - -/* - * "update" is a non-standard command that has to be supplied - * by external update.c; This is not included in mainline because - * it needs non-blocking CFI routines. - */ -#ifdef CONFIG_MONITOR_IS_IN_RAM -#define CONFIG_BOOTCOMMAND "" /* no autoboot in this case */ -#else -#if CONFIG_ASTRO_V532 -#define CONFIG_BOOTCOMMAND "protect off 0x80000 0x1ffffff;run env_check;"\ - "run xilinxload&&run alteraload&&bootm 0x80000;"\ - "update;reset" -#else -#define CONFIG_BOOTCOMMAND "protect off 0x80000 0x1ffffff;run env_check;"\ - "run xilinxload&&bootm 0x80000;update;reset" -#endif -#endif - -/* default RAM address for user programs */ -#define CONFIG_SYS_LOAD_ADDR 0x20000 - -#define CONFIG_FPGA_COUNT 1 -#define CONFIG_SYS_FPGA_PROG_FEEDBACK -#define CONFIG_SYS_FPGA_WAIT 1000 - -/* End of user parameters to be customized */ - -/* Defines memory range for test */ - -#define CONFIG_SYS_MEMTEST_START 0x40020000 -#define CONFIG_SYS_MEMTEST_END 0x41ffffff - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -/* Base register address */ - -#define CONFIG_SYS_MBAR 0xFC000000 /* Register Base Addrs */ - -/* System Conf. Reg. & System Protection Reg. */ - -#define CONFIG_SYS_SCR 0x0003; -#define CONFIG_SYS_SPR 0xffff; - -/* - * Definitions for initial stack pointer and data area (in internal SRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x8000 -#define CONFIG_SYS_INIT_RAM_CTRL 0x221 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* - * Start addresses for the final memory configuration - * (Set up by the startup code) - * for MCF5373, the allowable range is 0x40000000 to 0x7FF00000 - */ -#define CONFIG_SYS_SDRAM_BASE 0x40000000 - -/* - * Chipselect bank definitions - * - * CS0 - Flash 32MB (first 16MB) - * CS1 - Flash 32MB (second half) - * CS2 - FPGA - * CS3 - FPGA - * CS4 - unused - * CS5 - unused - */ -#define CONFIG_SYS_CS0_BASE 0 -#define CONFIG_SYS_CS0_MASK 0x00ff0001 -#define CONFIG_SYS_CS0_CTRL 0x00001fc0 - -#define CONFIG_SYS_CS1_BASE 0x01000000 -#define CONFIG_SYS_CS1_MASK 0x00ff0001 -#define CONFIG_SYS_CS1_CTRL 0x00001fc0 - -#define CONFIG_SYS_CS2_BASE 0x20000000 -#define CONFIG_SYS_CS2_MASK 0x00ff0001 -#define CONFIG_SYS_CS2_CTRL 0x0000fec0 - -#define CONFIG_SYS_CS3_BASE 0x21000000 -#define CONFIG_SYS_CS3_MASK 0x00ff0001 -#define CONFIG_SYS_CS3_CTRL 0x0000fec0 - -#define CONFIG_SYS_FLASH_BASE 0x00000000 - -#ifdef CONFIG_MONITOR_IS_IN_RAM -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#else -/* This is mainly used during relocation in start.S */ -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) -#endif -/* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MONITOR_LEN (256 << 10) - -#define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024) -/* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization ?? - */ -#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \ - (CONFIG_SYS_SDRAM_SIZE << 20)) - -/* FLASH organization */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 259 -#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 - -#define CONFIG_SYS_FLASH_SIZE 0x2000000 -#define CONFIG_SYS_FLASH_CFI_NONBLOCK 1 - -#define LDS_BOARD_TEXT \ - . = DEFINED(env_offset) ? env_offset : .; \ - env/embedded.o(.text*) - -#if ENABLE_JFFS -/* JFFS Partition offset set */ -#define CONFIG_SYS_JFFS2_FIRST_BANK 0 -#define CONFIG_SYS_JFFS2_NUM_BANKS 1 -/* 512k reserved for u-boot */ -#define CONFIG_SYS_JFFS2_FIRST_SECTOR 0x40 -#endif - -/* Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 16 - -#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 8) -#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 4) -#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA) -#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ - CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ - CF_ACR_EN | CF_ACR_SM_ALL) -#define CONFIG_SYS_CACHE_ICACR (CF_CACR_EC | CF_CACR_CINVA | \ - CF_CACR_DCM_P) - -#endif /* _CONFIG_ASTRO_MCF5373L_H */ -- cgit v1.2.3