From 1a691f101632955a994a0198fc5498b108e97fbc Mon Sep 17 00:00:00 2001 From: Iru Cai Date: Wed, 30 Oct 2019 15:42:15 +0800 Subject: rm include/configs --- include/configs/cobra5272.h | 336 -------------------------------------------- 1 file changed, 336 deletions(-) delete mode 100644 include/configs/cobra5272.h (limited to 'include/configs/cobra5272.h') diff --git a/include/configs/cobra5272.h b/include/configs/cobra5272.h deleted file mode 100644 index 337c875..0000000 --- a/include/configs/cobra5272.h +++ /dev/null @@ -1,336 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Configuation settings for the Sentec Cobra Board. - * - * (C) Copyright 2003 Josef Baumgartner - */ - -/* --- - * Version: U-Boot 1.0.0 - initial release for Sentec COBRA5272 board - * Date: 2004-03-29 - * Author: Florian Schlote - * - * For a description of configuration options please refer also to the - * general u-boot-1.x.x/README file - * --- - */ - -/* --- - * board/config.h - configuration options, board specific - * --- - */ - -#ifndef _CONFIG_COBRA5272_H -#define _CONFIG_COBRA5272_H - -/* --- - * Defines processor clock - important for correct timings concerning serial - * interface etc. - * --- - */ - -#define CONFIG_SYS_CLK 66000000 -#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ - -/* --- - * Enable use of Ethernet - * --- - */ -#define CONFIG_MCFFEC - -/* Enable Dma Timer */ -#define CONFIG_MCFTMR - -/* --- - * Define baudrate for UART1 (console output, tftp, ...) - * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud - * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command - * interface - * --- - */ - -#define CONFIG_MCFUART -#define CONFIG_SYS_UART_PORT (0) - -/* --- - * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change - * timeout acc. to your needs - * #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000 - * for 10 sec - * --- - */ - -#if 0 -#define CONFIG_WATCHDOG -#define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */ -#endif - -/* --- - * CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different - * bootloader residing in flash ('chainloading'); if you want to use - * chainloading or want to compile a u-boot binary that can be loaded into - * RAM via BDM set - * "#if 0" to "#if 1" - * You will need a first stage bootloader then, e. g. colilo or a working BDM - * cable (Background Debug Mode) - * - * Setting #if 0: u-boot will start from flash and relocate itself to RAM - * - * Please do not forget to modify the setting of CONFIG_SYS_TEXT_BASE - * in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000) - * - * --- - */ - -#if 0 -#define CONFIG_MONITOR_IS_IN_RAM /* monitor is started from a preloader */ -#endif - -/* --- - * Configuration for environment - * Environment is embedded in u-boot in the second sector of the flash - * --- - */ - -#ifndef CONFIG_MONITOR_IS_IN_RAM -#define CONFIG_ENV_OFFSET 0x4000 -#define CONFIG_ENV_SECT_SIZE 0x2000 -#else -#define CONFIG_ENV_ADDR 0xffe04000 -#define CONFIG_ENV_SECT_SIZE 0x2000 -#endif - -#define LDS_BOARD_TEXT \ - . = DEFINED(env_offset) ? env_offset : .; \ - env/embedded.o(.text); - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * Command line configuration. - */ - -#ifdef CONFIG_MCFFEC -# define CONFIG_MII_INIT 1 -# define CONFIG_SYS_DISCOVER_PHY -# define CONFIG_SYS_RX_ETH_BUFFER 8 -# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN - -# define CONFIG_SYS_FEC0_PINMUX 0 -# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE -# define MCFFEC_TOUT_LOOP 50000 -/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ -# ifndef CONFIG_SYS_DISCOVER_PHY -# define FECDUPLEX FULL -# define FECSPEED _100BASET -# else -# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN -# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN -# endif -# endif /* CONFIG_SYS_DISCOVER_PHY */ -#endif - -/* - *----------------------------------------------------------------------------- - * Define user parameters that have to be customized most likely - *----------------------------------------------------------------------------- - */ - -/*AUTOBOOT settings - booting images automatically by u-boot after power on*/ - -/* The following settings will be contained in the environment block ; if you -want to use a neutral environment all those settings can be manually set in -u-boot: 'set' command */ - -#if 0 - -#define CONFIG_BOOTCOMMAND "bootm 0xffe80000" /*Autoboto command, please -enter a valid image address in flash */ - -/* User network settings */ - -#define CONFIG_IPADDR 192.168.100.2 /* default board IP address */ -#define CONFIG_SERVERIP 192.168.100.1 /* default tftp server IP address */ - -#endif - -#define CONFIG_SYS_LOAD_ADDR 0x20000 /*Defines default RAM address -from which user programs will be started */ - -/*---*/ - -/* - *----------------------------------------------------------------------------- - * End of user parameters to be customized - *----------------------------------------------------------------------------- - */ - -/* --- - * Defines memory range for test - * --- - */ - -#define CONFIG_SYS_MEMTEST_START 0x400 -#define CONFIG_SYS_MEMTEST_END 0x380000 - -/* --- - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - * --- - */ - -/* --- - * Base register address - * --- - */ - -#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ - -/* --- - * System Conf. Reg. & System Protection Reg. - * --- - */ - -#define CONFIG_SYS_SCR 0x0003 -#define CONFIG_SYS_SPR 0xffff - -/* --- - * Ethernet settings - * --- - */ - -#define CONFIG_SYS_DISCOVER_PHY -#define CONFIG_SYS_ENET_BD_BASE 0x780000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in internal SRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -/* - *------------------------------------------------------------------------- - * RAM SIZE (is defined above) - *----------------------------------------------------------------------- - */ - -/* #define CONFIG_SYS_SDRAM_SIZE 16 */ - -/* - *----------------------------------------------------------------------- - */ - -#define CONFIG_SYS_FLASH_BASE 0xffe00000 - -#ifdef CONFIG_MONITOR_IS_IN_RAM -#define CONFIG_SYS_MONITOR_BASE 0x20000 -#else -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) -#endif - -#define CONFIG_SYS_MONITOR_LEN 0x20000 -#define CONFIG_SYS_MALLOC_LEN (256 << 10) -#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization ?? - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 /* flash timeout */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 - -#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 8) -#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 4) -#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) -#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ - CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ - CF_ACR_EN | CF_ACR_SM_ALL) -#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ - CF_CACR_DISD | CF_CACR_INVI | \ - CF_CACR_CEIB | CF_CACR_DCM | \ - CF_CACR_EUSP) - -/*----------------------------------------------------------------------- - * Memory bank definitions - * - * Please refer also to Motorola Coldfire user manual - Chapter XXX - * - */ -#define CONFIG_SYS_BR0_PRELIM 0xFFE00201 -#define CONFIG_SYS_OR0_PRELIM 0xFFE00014 - -#define CONFIG_SYS_BR1_PRELIM 0 -#define CONFIG_SYS_OR1_PRELIM 0 - -#define CONFIG_SYS_BR2_PRELIM 0 -#define CONFIG_SYS_OR2_PRELIM 0 - -#define CONFIG_SYS_BR3_PRELIM 0 -#define CONFIG_SYS_OR3_PRELIM 0 - -#define CONFIG_SYS_BR4_PRELIM 0 -#define CONFIG_SYS_OR4_PRELIM 0 - -#define CONFIG_SYS_BR5_PRELIM 0 -#define CONFIG_SYS_OR5_PRELIM 0 - -#define CONFIG_SYS_BR6_PRELIM 0 -#define CONFIG_SYS_OR6_PRELIM 0 - -#define CONFIG_SYS_BR7_PRELIM 0x00000701 -#define CONFIG_SYS_OR7_PRELIM 0xFF00007C - -/*----------------------------------------------------------------------- - * LED config - */ -#define LED_STAT_0 0xffff /*all LEDs off*/ -#define LED_STAT_1 0xfffe -#define LED_STAT_2 0xfffd -#define LED_STAT_3 0xfffb -#define LED_STAT_4 0xfff7 -#define LED_STAT_5 0xffef -#define LED_STAT_6 0xffdf -#define LED_STAT_7 0xff00 /*all LEDs on*/ - -/*----------------------------------------------------------------------- - * Port configuration (GPIO) - */ -#define CONFIG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external -GPIO*/ -#define CONFIG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs -(1^=output, 0^=input) */ -#define CONFIG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */ -#define CONFIG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART -configuration */ -#define CONFIG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */ -#define CONFIG_SYS_PBDAT 0x0000 /* PortB value reg. */ -#define CONFIG_SYS_PDCNT 0x00000000 /* PortD control reg. */ - -#endif /* _CONFIG_COBRA5272_H */ -- cgit v1.2.3