From 1a691f101632955a994a0198fc5498b108e97fbc Mon Sep 17 00:00:00 2001 From: Iru Cai Date: Wed, 30 Oct 2019 15:42:15 +0800 Subject: rm include/configs --- include/configs/integrator-common.h | 90 ------------------------------------- 1 file changed, 90 deletions(-) delete mode 100644 include/configs/integrator-common.h (limited to 'include/configs/integrator-common.h') diff --git a/include/configs/integrator-common.h b/include/configs/integrator-common.h deleted file mode 100644 index 9223fc2..0000000 --- a/include/configs/integrator-common.h +++ /dev/null @@ -1,90 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2012 - * Linaro - * Linus Walleij - * Common ARM Integrator configuration settings - */ - -#define CONFIG_SYS_MEMTEST_START 0x100000 -#define CONFIG_SYS_MEMTEST_END 0x10000000 -#define CONFIG_SYS_TIMERBASE 0x13000100 /* Timer1 */ -#define CONFIG_SYS_LOAD_ADDR 0x7fc0 /* default load address */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) /* Size of malloc() pool */ - -#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS - -/* - * There are various dependencies on the core module (CM) fitted - * Users should refer to their CM user guide - */ -#include "armcoremodule.h" - -/* - * Initialize and remap the core module, use SPD to detect memory size - * If CONFIG_SKIP_LOWLEVEL_INIT is not defined & - * the core module has a CM_INIT register - * then the U-Boot initialisation code will - * e.g. ARM Boot Monitor or pre-loader is repeated once - * (to re-initialise any existing CM_INIT settings to safe values). - * - * This is usually not the desired behaviour since the platform - * will either reboot into the ARM monitor (or pre-loader) - * or continuously cycle thru it without U-Boot running, - * depending upon the setting of Integrator/CP switch S2-4. - * - * However it may be needed if Integrator/CP switch S2-1 - * is set OFF to boot direct into U-Boot. - * In that case comment out the line below. - */ -#define CONFIG_CM_INIT -#define CONFIG_CM_REMAP -#define CONFIG_CM_SPD_DETECT - -/* - * The ARM boot monitor initializes the board. - * However, the default U-Boot code also performs the initialization. - * If desired, this can be prevented by defining SKIP_LOWLEVEL_INIT - * - see documentation supplied with board for details of how to choose the - * image to run at reset/power up - * e.g. whether the ARM Boot Monitor runs before U-Boot - */ -/* #define CONFIG_SKIP_LOWLEVEL_INIT */ - -/* - * The ARM boot monitor does not relocate U-Boot. - * However, the default U-Boot code performs the relocation check, - * and may relocate the code if the memory map is changed. - * If necessary this can be prevented by defining SKIP_RELOCATE_UBOOT - */ -/* #define SKIP_CONFIG_RELOCATE_UBOOT */ - -/* - * Physical Memory Map - */ -#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */ -#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */ -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_SIZE PHYS_SDRAM_1_SIZE -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET - -/* - * FLASH and environment organization - * Top varies according to amount fitted - * Reserve top 4 blocks of flash - * - ARM Boot Monitor - * - Unused - * - SIB block - * - U-Boot environment - */ -#define CONFIG_SYS_FLASH_BASE 0x24000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 - -/* Timeout values in ticks */ -#define CONFIG_SYS_FLASH_ERASE_TOUT (2 * CONFIG_SYS_HZ) /* Erase Timeout */ -#define CONFIG_SYS_FLASH_WRITE_TOUT (2 * CONFIG_SYS_HZ) /* Write Timeout */ -#define CONFIG_SYS_FLASH_EMPTY_INFO /* flinfo indicates empty blocks */ -- cgit v1.2.3