From 1a691f101632955a994a0198fc5498b108e97fbc Mon Sep 17 00:00:00 2001
From: Iru Cai <mytbk920423@gmail.com>
Date: Wed, 30 Oct 2019 15:42:15 +0800
Subject: rm include/configs

---
 include/configs/xpedite537x.h | 500 ------------------------------------------
 1 file changed, 500 deletions(-)
 delete mode 100644 include/configs/xpedite537x.h

(limited to 'include/configs/xpedite537x.h')

diff --git a/include/configs/xpedite537x.h b/include/configs/xpedite537x.h
deleted file mode 100644
index 73e1fa3..0000000
--- a/include/configs/xpedite537x.h
+++ /dev/null
@@ -1,500 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2008 Extreme Engineering Solutions, Inc.
- * Copyright 2007-2008 Freescale Semiconductor, Inc.
- */
-
-/*
- * xpedite537x board configuration file
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_SYS_BOARD_NAME	"XPedite5370"
-#define CONFIG_SYS_FORM_3U_VPX	1
-
-#define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup */
-#define CONFIG_PCIE1		1	/* PCIE controller 1 */
-#define CONFIG_PCIE2		1	/* PCIE controller 2 */
-#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
-#define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
-
-/*
- * Multicore config
- */
-#define CONFIG_BPTR_VIRT_ADDR	0xee000000	/* virt boot page address */
-#define CONFIG_MPC8xxx_DISABLE_BPTR		/* Don't leave BPTR enabled */
-
-/*
- * DDR config
- */
-#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
-#define CONFIG_DDR_SPD
-#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
-#define SPD_EEPROM_ADDRESS1		0x54	/* Both channels use the */
-#define SPD_EEPROM_ADDRESS2		0x54	/* same SPD data         */
-#define SPD_EEPROM_OFFSET		0x200	/* OFFSET of SPD in EEPROM */
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	1
-#define CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_VERY_BIG_RAM
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_board_sys_clk(unsigned long dummy);
-extern unsigned long get_board_ddr_clk(unsigned long dummy);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /* sysclk for MPC85xx */
-#define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk(0) /* ddrclk for MPC85xx */
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE			/* toggle L2 cache */
-#define CONFIG_BTB			/* toggle branch predition */
-#define CONFIG_ENABLE_36BIT_PHYS	1
-
-#define CONFIG_SYS_CCSRBAR		0xef000000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
-
-/*
- * Diagnostics
- */
-#define CONFIG_SYS_MEMTEST_START	0x10000000
-#define CONFIG_SYS_MEMTEST_END		0x20000000
-#define CONFIG_POST			(CONFIG_SYS_POST_MEMORY | \
-					 CONFIG_SYS_POST_I2C)
-/* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */
-#define I2C_ADDR_IGNORE_LIST		{0x50}
-
-/*
- * Memory map
- * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
- * 0x8000_0000	0xbfff_ffff	PCIe1 Mem		1G non-cacheable
- * 0xc000_0000	0xcfff_ffff	PCIe2 Mem		256M non-cacheable
- * 0xe000_0000	0xe7ff_ffff	SRAM/SSRAM/L1 Cache	128M non-cacheable
- * 0xe800_0000	0xe87f_ffff	PCIe1 IO		8M non-cacheable
- * 0xe880_0000	0xe8ff_ffff	PCIe2 IO		8M non-cacheable
- * 0xee00_0000	0xee00_ffff	Boot page translation	4K non-cacheable
- * 0xef00_0000	0xef0f_ffff	CCSR/IMMR		1M non-cacheable
- * 0xef80_0000	0xef8f_ffff	NAND Flash		1M non-cacheable
- * 0xf000_0000	0xf7ff_ffff	NOR Flash 2		128M non-cacheable
- * 0xf800_0000	0xffff_ffff	NOR Flash 1		128M non-cacheable
- */
-
-#define CONFIG_SYS_LBC_LCRR	(LCRR_CLKDIV_8 | LCRR_EADC_3)
-
-/*
- * NAND flash configuration
- */
-#define CONFIG_SYS_NAND_BASE		0xef800000
-#define CONFIG_SYS_NAND_BASE2		0xef840000 /* Unused at this time */
-#define CONFIG_SYS_NAND_BASE_LIST	{CONFIG_SYS_NAND_BASE, \
-					 CONFIG_SYS_NAND_BASE2}
-#define CONFIG_SYS_MAX_NAND_DEVICE	2
-#define CONFIG_NAND_FSL_ELBC
-
-/*
- * NOR flash configuration
- */
-#define CONFIG_SYS_FLASH_BASE		0xf8000000
-#define CONFIG_SYS_FLASH_BASE2		0xf0000000
-#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
-#define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
-#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST	{ {0xfff40000, 0xc0000}, \
-						  {0xf7f40000, 0xc0000} }
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-
-/*
- * Chip select configuration
- */
-/* NOR Flash 0 on CS0 */
-#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE	| \
-				 BR_PS_16		| \
-				 BR_V)
-#define CONFIG_SYS_OR0_PRELIM	(OR_AM_128MB		| \
-				 OR_GPCM_CSNT		| \
-				 OR_GPCM_XACS		| \
-				 OR_GPCM_ACS_DIV2	| \
-				 OR_GPCM_SCY_8		| \
-				 OR_GPCM_TRLX		| \
-				 OR_GPCM_EHTR		| \
-				 OR_GPCM_EAD)
-
-/* NOR Flash 1 on CS1 */
-#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_FLASH_BASE2	| \
-				 BR_PS_16		| \
-				 BR_V)
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
-
-/* NAND flash on CS2 */
-#define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_NAND_BASE	| \
-				 (2<<BR_DECC_SHIFT)	| \
-				 BR_PS_8		| \
-				 BR_MS_FCM		| \
-				 BR_V)
-
-/* NAND flash on CS2 */
-#define CONFIG_SYS_OR2_PRELIM	(OR_AM_256KB	| \
-				 OR_FCM_PGS	| \
-				 OR_FCM_CSCT	| \
-				 OR_FCM_CST	| \
-				 OR_FCM_CHT	| \
-				 OR_FCM_SCY_1	| \
-				 OR_FCM_TRLX	| \
-				 OR_FCM_EHTR)
-
-/* NAND flash on CS3 */
-#define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_NAND_BASE2	| \
-				 (2<<BR_DECC_SHIFT)	| \
-				 BR_PS_8		| \
-				 BR_MS_FCM		| \
-				 BR_V)
-#define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
-
-/*
- * Use L1 as initial stack
- */
-#define CONFIG_SYS_INIT_RAM_LOCK	1
-#define CONFIG_SYS_INIT_RAM_ADDR	0xe0000000
-#define CONFIG_SYS_INIT_RAM_SIZE		0x00004000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
-#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
-#define CONFIG_SYS_BAUDRATE_TABLE	\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-#define CONFIG_LOADS_ECHO		1	/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
-
-/* PEX8518 slave I2C interface */
-#define CONFIG_SYS_I2C_PEX8518_ADDR	0x70
-
-/* I2C DS1631 temperature sensor */
-#define CONFIG_SYS_I2C_LM90_ADDR	0x4c
-
-/* I2C EEPROM - AT24C128B */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x54
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6	/* 64 byte pages */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* take up to 10 msec */
-
-/* I2C RTC */
-#define CONFIG_RTC_M41T11		1
-#define CONFIG_SYS_I2C_RTC_ADDR		0x68
-#define CONFIG_SYS_M41T11_BASE_YEAR	2000
-
-/* GPIO */
-#define CONFIG_PCA953X
-#define CONFIG_SYS_I2C_PCA953X_ADDR0	0x18
-#define CONFIG_SYS_I2C_PCA953X_ADDR1	0x1c
-#define CONFIG_SYS_I2C_PCA953X_ADDR2	0x1e
-#define CONFIG_SYS_I2C_PCA953X_ADDR3	0x1f
-#define CONFIG_SYS_I2C_PCA953X_ADDR	CONFIG_SYS_I2C_PCA953X_ADDR0
-
-/*
- * PU = pulled high, PD = pulled low
- * I = input, O = output, IO = input/output
- */
-/* PCA9557 @ 0x18*/
-#define CONFIG_SYS_PCA953X_C0_SER0_EN		0x01 /* PU; UART0 enable (1: enabled) */
-#define CONFIG_SYS_PCA953X_C0_SER0_MODE		0x02 /* PU; UART0 serial mode select */
-#define CONFIG_SYS_PCA953X_C0_SER1_EN		0x04 /* PU; UART1 enable (1: enabled) */
-#define CONFIG_SYS_PCA953X_C0_SER1_MODE		0x08 /* PU; UART1 serial mode select */
-#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS	0x10 /* PU; Boot flash CS select */
-#define CONFIG_SYS_PCA953X_NVM_WP		0x20 /* PU; Set to 0 to enable NVM writing */
-#define CONFIG_SYS_PCA953X_C0_VCORE_VID2	0x40 /* VID2 of ISL6262 */
-#define CONFIG_SYS_PCA953X_C0_VCORE_VID3	0x80 /* VID3 of ISL6262 */
-
-/* PCA9557 @ 0x1c*/
-#define CONFIG_SYS_PCA953X_XMC0_ROOT0		0x01 /* PU; Low if XMC is RC */
-#define CONFIG_SYS_PCA953X_XMC0_MVMR0		0x02 /* XMC EEPROM write protect */
-#define CONFIG_SYS_PCA953X_XMC0_WAKE		0x04 /* PU; XMC wake */
-#define CONFIG_SYS_PCA953X_XMC0_BIST		0x08 /* PU; XMC built in self test */
-#define CONFIG_SYS_PCA953X_XMC_PRESENT		0x10 /* PU; Low if XMC module installed */
-#define CONFIG_SYS_PCA953X_PMC_PRESENT		0x20 /* PU; Low if PMC module installed */
-#define CONFIG_SYS_PCA953X_PMC0_MONARCH		0x40 /* PMC monarch mode enable */
-#define CONFIG_SYS_PCA953X_PMC0_EREADY		0x80 /* PU; PMC PCI eready */
-
-/* PCA9557 @ 0x1e*/
-#define CONFIG_SYS_PCA953X_P0_GA0		0x01 /* PU; VPX Geographical address */
-#define CONFIG_SYS_PCA953X_P0_GA1		0x02 /* PU; VPX Geographical address */
-#define CONFIG_SYS_PCA953X_P0_GA2		0x04 /* PU; VPX Geographical address */
-#define CONFIG_SYS_PCA953X_P0_GA3		0x08 /* PU; VPX Geographical address */
-#define CONFIG_SYS_PCA953X_P0_GA4		0x10 /* PU; VPX Geographical address */
-#define CONFIG_SYS_PCA953X_P0_GAP		0x20 /* PU; tied to VPX P0.GAP */
-#define CONFIG_SYS_PCA953X_P1_SYSEN		0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */
-
-/* PCA9557 @ 0x1f */
-#define CONFIG_SYS_PCA953X_GPIO_VPX0		0x01 /* PU */
-#define CONFIG_SYS_PCA953X_GPIO_VPX1		0x02 /* PU */
-#define CONFIG_SYS_PCA953X_GPIO_VPX2		0x04 /* PU */
-#define CONFIG_SYS_PCA953X_GPIO_VPX3		0x08 /* PU */
-#define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL	0x10 /* PD; I2C master source for FRU SEEPROM */
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-/* PCIE1 - VPX P1 */
-#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BUS
-#define CONFIG_SYS_PCIE1_MEM_SIZE	0x40000000	/* 1G */
-#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS	0xe8000000
-#define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000	/* 8M */
-
-/* PCIE2 - PEX8518 */
-#define CONFIG_SYS_PCIE2_MEM_BUS	0xc0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BUS
-#define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS	0xe8800000
-#define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000	/* 8M */
-
-/*
- * Networking options
- */
-#define CONFIG_TSEC_TBI
-#define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
-#define CONFIG_ETHPRIME		"eTSEC2"
-
-/*
- * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
- * 1000mbps SGMII link
- */
-#define CONFIG_TSEC_TBICR_SETTINGS ( \
-		TBICR_PHY_RESET \
-		| TBICR_FULL_DUPLEX \
-		| TBICR_SPEED1_SET \
-		)
-
-#define CONFIG_TSEC1		1
-#define CONFIG_TSEC1_NAME	"eTSEC1"
-#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC1_PHY_ADDR		1
-#define TSEC1_PHYIDX		0
-#define CONFIG_HAS_ETH0
-
-#define CONFIG_TSEC2		1
-#define CONFIG_TSEC2_NAME	"eTSEC2"
-#define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_PHY_ADDR		2
-#define TSEC2_PHYIDX		0
-#define CONFIG_HAS_ETH1
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-#define CONFIG_LOADADDR		0x1000000	/* default location for tftp and bootm */
-#define CONFIG_INTEGRITY			/* support booting INTEGRITY OS */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(16 << 20)	/* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN	(16 << 20)	/* Increase max gunzip size */
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_SECT_SIZE	0x20000		/* 128k (one sector) for env */
-#define CONFIG_ENV_SIZE		0x8000
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - (256 * 1024))
-
-/*
- * Flash memory map:
- * fff80000 - ffffffff     Pri U-Boot (512 KB)
- * fff40000 - fff7ffff     Pri U-Boot Environment (256 KB)
- * fff00000 - fff3ffff     Pri FDT (256KB)
- * fef00000 - ffefffff     Pri OS image (16MB)
- * f8000000 - feefffff     Pri OS Use/Filesystem (111MB)
- *
- * f7f80000 - f7ffffff     Sec U-Boot (512 KB)
- * f7f40000 - f7f7ffff     Sec U-Boot Environment (256 KB)
- * f7f00000 - f7f3ffff     Sec FDT (256KB)
- * f6f00000 - f7efffff     Sec OS image (16MB)
- * f0000000 - f6efffff     Sec OS Use/Filesystem (111MB)
- */
-#define CONFIG_UBOOT1_ENV_ADDR	__stringify(0xfff80000)
-#define CONFIG_UBOOT2_ENV_ADDR	__stringify(0xf7f80000)
-#define CONFIG_FDT1_ENV_ADDR	__stringify(0xfff00000)
-#define CONFIG_FDT2_ENV_ADDR	__stringify(0xf7f00000)
-#define CONFIG_OS1_ENV_ADDR	__stringify(0xfef00000)
-#define CONFIG_OS2_ENV_ADDR	__stringify(0xf6f00000)
-
-#define CONFIG_PROG_UBOOT1						\
-	"$download_cmd $loadaddr $ubootfile; "				\
-	"if test $? -eq 0; then "					\
-		"protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
-		"erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
-		"cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "	\
-		"protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
-		"cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "	\
-		"if test $? -ne 0; then "				\
-			"echo PROGRAM FAILED; "				\
-		"else; "						\
-			"echo PROGRAM SUCCEEDED; "			\
-		"fi; "							\
-	"else; "							\
-		"echo DOWNLOAD FAILED; "				\
-	"fi;"
-
-#define CONFIG_PROG_UBOOT2						\
-	"$download_cmd $loadaddr $ubootfile; "				\
-	"if test $? -eq 0; then "					\
-		"protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
-		"erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
-		"cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "	\
-		"protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
-		"cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "	\
-		"if test $? -ne 0; then "				\
-			"echo PROGRAM FAILED; "				\
-		"else; "						\
-			"echo PROGRAM SUCCEEDED; "			\
-		"fi; "							\
-	"else; "							\
-		"echo DOWNLOAD FAILED; "				\
-	"fi;"
-
-#define CONFIG_BOOT_OS_NET						\
-	"$download_cmd $osaddr $osfile; "				\
-	"if test $? -eq 0; then "					\
-		"if test -n $fdtaddr; then "				\
-			"$download_cmd $fdtaddr $fdtfile; "		\
-			"if test $? -eq 0; then "			\
-				"bootm $osaddr - $fdtaddr; "		\
-			"else; "					\
-				"echo FDT DOWNLOAD FAILED; "		\
-			"fi; "						\
-		"else; "						\
-			"bootm $osaddr; "				\
-		"fi; "							\
-	"else; "							\
-		"echo OS DOWNLOAD FAILED; "				\
-	"fi;"
-
-#define CONFIG_PROG_OS1							\
-	"$download_cmd $osaddr $osfile; "				\
-	"if test $? -eq 0; then "					\
-		"erase "CONFIG_OS1_ENV_ADDR" +$filesize; "		\
-		"cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
-		"cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
-		"if test $? -ne 0; then "				\
-			"echo OS PROGRAM FAILED; "			\
-		"else; "						\
-			"echo OS PROGRAM SUCCEEDED; "			\
-		"fi; "							\
-	"else; "							\
-		"echo OS DOWNLOAD FAILED; "				\
-	"fi;"
-
-#define CONFIG_PROG_OS2							\
-	"$download_cmd $osaddr $osfile; "				\
-	"if test $? -eq 0; then "					\
-		"erase "CONFIG_OS2_ENV_ADDR" +$filesize; "		\
-		"cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
-		"cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
-		"if test $? -ne 0; then "				\
-			"echo OS PROGRAM FAILED; "			\
-		"else; "						\
-			"echo OS PROGRAM SUCCEEDED; "			\
-		"fi; "							\
-	"else; "							\
-		"echo OS DOWNLOAD FAILED; "				\
-	"fi;"
-
-#define CONFIG_PROG_FDT1						\
-	"$download_cmd $fdtaddr $fdtfile; "				\
-	"if test $? -eq 0; then "					\
-		"erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"		\
-		"cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
-		"cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
-		"if test $? -ne 0; then "				\
-			"echo FDT PROGRAM FAILED; "			\
-		"else; "						\
-			"echo FDT PROGRAM SUCCEEDED; "			\
-		"fi; "							\
-	"else; "							\
-		"echo FDT DOWNLOAD FAILED; "				\
-	"fi;"
-
-#define CONFIG_PROG_FDT2						\
-	"$download_cmd $fdtaddr $fdtfile; "				\
-	"if test $? -eq 0; then "					\
-		"erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"		\
-		"cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
-		"cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
-		"if test $? -ne 0; then "				\
-			"echo FDT PROGRAM FAILED; "			\
-		"else; "						\
-			"echo FDT PROGRAM SUCCEEDED; "			\
-		"fi; "							\
-	"else; "							\
-		"echo FDT DOWNLOAD FAILED; "				\
-	"fi;"
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"autoload=yes\0"						\
-	"download_cmd=tftp\0"						\
-	"console_args=console=ttyS0,115200\0"				\
-	"root_args=root=/dev/nfs rw\0"					\
-	"misc_args=ip=on\0"						\
-	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
-	"bootfile=/home/user/file\0"					\
-	"osfile=/home/user/board.uImage\0"				\
-	"fdtfile=/home/user/board.dtb\0"				\
-	"ubootfile=/home/user/u-boot.bin\0"				\
-	"fdtaddr=0x1e00000\0"						\
-	"osaddr=0x1000000\0"						\
-	"loadaddr=0x1000000\0"						\
-	"prog_uboot1="CONFIG_PROG_UBOOT1"\0"				\
-	"prog_uboot2="CONFIG_PROG_UBOOT2"\0"				\
-	"prog_os1="CONFIG_PROG_OS1"\0"					\
-	"prog_os2="CONFIG_PROG_OS2"\0"					\
-	"prog_fdt1="CONFIG_PROG_FDT1"\0"				\
-	"prog_fdt2="CONFIG_PROG_FDT2"\0"				\
-	"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"		\
-	"bootcmd_flash1=run set_bootargs; "				\
-		"bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
-	"bootcmd_flash2=run set_bootargs; "				\
-		"bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
-	"bootcmd=run bootcmd_flash1\0"
-#endif	/* __CONFIG_H */
-- 
cgit v1.2.3