#*************************************************************************
#*************************************************************************
#**                                                                     **
#**        (C)Copyright 1985-2013, American Megatrends, Inc.            **
#**                                                                     **
#**                       All Rights Reserved.                          **
#**                                                                     **
#**      5555 Oakbrook Parkway, Suite 200, Norcross, GA 30093           **
#**                                                                     **
#**                       Phone: (770)-246-8600                         **
#**                                                                     **
#*************************************************************************
#*************************************************************************

#*************************************************************************
# $Header: /Alaska/BIN/Chipset/Intel/SouthBridge/LynxPoint/Intel Pch SB Board/SB.sdl 65    7/21/14 10:45p Mirayang $
#
# $Revision: 65 $
#
# $Date: 7/21/14 10:45p $
#*************************************************************************
# Revision History
# ----------------
# $Log: /Alaska/BIN/Chipset/Intel/SouthBridge/LynxPoint/Intel Pch SB Board/SB.sdl $
# 
# 65    7/21/14 10:45p Mirayang
# [TAG]  		EIP176923 
# [Category]  	Improvement
# [Description]  	Program BUC.SDO to 1 on normal boot in PCH component.
# 
# 64    5/16/14 6:19a Barretlin
# [TAG]  		EIP167087
# [Category]  	Improvement
# [Description]  	BIOS security improvement on Haswell CRB project
# [Files]  		SBGeneric.c SBDxe.c SBCspLib.h Sb.sdl Sb.sd Sb.h
# 
# 63    3/13/14 11:06a Barretlin
# [TAG]  		EIP153695
# [Category]  	Improvement
# [Description]  	USB Per port control is not reasonable when
# OEM_USBPREPORT_DISABLE_SUPPORT token is Enabled and USB devices are
# behind hubs
# [Files]  		Sb.sdl Sb.sd Sb.uni GetSetupData.c SbDxe.c PchUsbCommon.c
# PchRegsUsb.h
# 
# 62    11/19/13 7:34a Barretlin
# [TAG]  		EIP141917
# [Category]  	New Feature
# [Description]  	Support SetTimer() with HPET Timer on Lynx Point
# [Files]  		SB.sdl SBGeneric.c SBDxe.c SbHpet.h sbProtocal.cif
# SamrtTimer.sdl
# 
# 61    10/28/13 2:46a Barretlin
# [TAG]  		EIP N/A
# [Category]  	Improvement
# [Description]  	add programming serial IO device's SSID
# [Files]  		SB.sdl SB.H
# 
# 60    10/06/13 2:27a Barretlin
# [TAG]  		EIP138340
# [Category]  	Improvement
# [Description]  	SATA drive detection issue in PCH Platform BIOS
# reference code revision 1.6.2
# [Files]  		SB.sdl SBPEI.c
# 
# 59    9/18/13 1:01a Barretlin
# [TAG]  		EIP N/A
# [Category]  	Improvement
# [Description]  	change default value of PCH_RCRB_OIC_CEN token
# [Files]  		SB.sdl
# 
# 58    9/17/13 2:46p Barretlin
# [TAG]  		EIP N/A
# [Category]  	Improvement
# [Description]  	use token to decide SATA RxEq policy vaule
# [Files]  		SB.sdl SbPei.c
# 
# 57    9/17/13 1:58p Barretlin
# [TAG]  		EIP N/A
# [Category]  	Improvement
# [Description]  	set a token to enable/disable SATA DLAE bit
# [Files]  		SB.sdl SBDxe.c
# 
# 56    9/17/13 8:32a Barretlin
# [TAG]  		EIP136354
# [Category]  	Improvement
# [Description]  	remove setting RCBA Coprocessor Error Enable bit
# [Files]  		SB.sdl SbPei.c
# 
# 55    8/23/13 3:39a Barretlin
# [TAG]  		EIP133819
# [Category]  	Improvement
# [Description]  	update for Intel PCH RC 1.6.2.0
# [Files]  		SB.sdl SBPEI.c
# 
# 54    8/22/13 3:01a Barretlin
# [TAG]  		EIP N/A
# [Category]  	Improvement
# [Description]  	make sure CRB without SIO solution only for SharkBay
# MB/ULT CRB
# [Files]  		SB.sdl SB.mak
# 
# 53    7/30/13 3:05a Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Support CRB without Super IO.
# [Files]  		SB.sdl, SB.mak
# 
# 52    7/03/13 8:05a Scottyang
# [TAG]  		EIP124410
# [Category]  	Improvement
# [Description]  	Implement SMBIOS type 88h for CRID.
# [Files]  		SBDxe.c, SB.sdl, SB.sd, SBSetup.c, SBSetup.sdl
# 
# 51    4/24/13 2:14a Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Porting GPI interrupt by LPT-LP EDS 1.5.
# [Files]  		SB.sdl, SB.H, SBPPI.h, SBPEI.c
# 
# 50    4/23/13 4:15a Wesleychen
# [TAG]         None
# [Category]    Improvement
# [Description] Add token "ONLY_CLEAR_RTC_EN_IN_PEI" for improve
# "EIP120623".
# [Files]       AcpiModeEnable.c; SB.SDL; SBPEI.c
# 
# 49    4/15/13 10:58p Wesleychen
# [TAG]          None
# [Category]     Improvement
# [Description]  Change the default of SX_NOTIFY_PWRB to 1.
# [Files]        SB.SDL
# 
# 48    4/09/13 11:42p Wesleychen
# [TAG]           EIP120480
# [Category]      Improvement
# [Description]   Always disabling PCH platform policy "ExternalObffEn".
# [Files]         SB.SDL, SBDXE.c
# 
# 47    4/08/13 2:55a Wesleychen
# 
# [TAG]           EIP118045
# [Category]      Improvement
# [Description]   Creat tokens to support Power Button Notify
#                 for misc events.
#                 Neew token: "SX_NOTIFY_PWRB"
# [Files]         SB.SDL; SB.ASL
# 
# 46    4/08/13 2:46a Wesleychen
# [TAG]           EIP120159
# [Category]      Improvement
# [Description]   Update for Intel PCH LPT RC140.
#                 Added new tokens:
#                 1. "PCH_RESET_CYCLE_DURATION"
#                 2. "LEGACY_DMA_DISABLE"
# [Files]         SB.SDL; SBDXE.c
# 
# 45    4/08/13 2:40a Wesleychen
# [TAG]         EIP116939
# [Category]    Bug Fix
# [Severity]    Normal
# [Symptom]     The available memory size is less than
#               2GB in Windowss 7 32 bit.
# [RootCause]   The "SB_TEMP_MMIO_BASE" is too low.
# [Solution]    Rearrange "SB_TEMP_MMIO_BASE" to
#               4GB - 16M(ROM) - 64KB (Intel Required).
# [Files]       SB.SDL; SBDxe.c
# 
# 44    4/02/13 10:30a Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Follow Intel BIOS 114.4 GPIO setting at ULT platform.
# [Files]  		SB.sdl
# SBPEIBoard.c
# 
# 42    4/02/13 3:32a Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Clear PCIE retrain bit for some device which cannot
# clear this bit.
# [Files]  		SB.sdl, PchPciExpressHelpersLibrary.c
# 
# 41    3/22/13 5:09a Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Wireless LAN PHY use SLP_WLAN# pin
# [Files]  		SB.sdl, SBDxe.c
# 
# 40    3/04/13 9:58p Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Add token for PCH policy.
# [Files]  		SBDxe.c, SB.sdl
# 
# 39    2/26/13 1:01a Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Follow intel BIOS V112 to change IRQ rout.
# [Files]  		SB.sdl, SBPEI.c
# 
# 38    2/18/13 2:54a Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Set PCIE root port function swapping default is
# disable.
# [Files]  		SB.sd, SB.uni, SB.sdl
# 
# 37    1/30/13 12:58a Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Update for 4.6.5.3_TBT_002.
# [Files]  		SB.sd, SB.sdl
# 
# 36    1/28/13 4:14a Scottyang
# [TAG]  		EIP108803
# [Category]  	Improvement
# [Description]  	Disable usb port after setup.
# [Files]  		SB.sdl, SBDxe.c
# 
# 35    1/25/13 7:51a Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Use token to set "BIOS Lock", "SMI Lock", BIOS
# Interface Lock", "GPIO Lock" and "RTC RAM Lock".
# [Files]  		SB.sd, SB.sdl
# 
# 34    1/24/13 12:48a Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Create GPIO function token for ULT.
# [Files]  		SB.sdl
# 
# 33    1/17/13 3:33a Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Correct ULT GPIO's help message
# [Files]  		SB.sdl
# SBPEIBoard.c
# 
# 32    1/11/13 1:52a Scottyang
# [TAG]  		EIP88358
# [Category]  	Improvement
# [Description]  	Add FORCE_USER_TO_SETUP_IF_CMOS_BAD token
# [Files]  		SBDex.c, SBPei.c, RTC.h, SB.sdl
# 
# 31    1/11/13 12:44a Scottyang
# [TAG]         EIP81593
# [Category]    Improvement
# [Description] Added new SDL token "COLD_RESET_WITH_POWER_CYCLE".
# [Files]       SB.sdl,  SBGeneric.c,  PchResetCommon.c,
# PchResetCommonLib.sdl
# 
# 30    1/10/13 8:19a Scottyang
# [TAG]  		EIP111666
# [Category]  	New Feature
# [Description]  	Support OEM reset callback function Elink.
# [Files]  		SB.mak, SBCspLib.h, SBGeneric.c, SB.sdl, PchReset.c
# 
# 29    1/09/13 8:24a Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Synchronous GPIO with Intel BIOS V104.2.
# [Files]  		SB.sdl
# SBPEIBoard.c
# 
# 28    11/20/12 9:52p Scottyang
# [TAG] None
# [Category] Improvement
# [Description] Change ASL build path by token. 
# [Files] SB.sdl, SB.mak
# 
# 27    11/08/12 8:41p Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Change APIC ID to 02.
# [Files]  		SB.sdl
# 
# 26    11/08/12 7:15a Scottyang
# [TAG]  		None
# [Category]  	New Feature
# [Description]  	Add token "PROGRAM_GPIO_TYPE" for select ULT GPIO
# program function(token or array directly).
# [Files]  		SB.sdl, SBPEIBoard.c
# 
# 25    11/06/12 8:03a Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Change "SB_TEMP_MMIO_BASE" to "0xDFFF0000"
# [Files]  		SB.sdl
# 
# 23    10/30/12 10:10p Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Update SATA RAID rom to 12.5.0.1710
# [Files]  		SataDriver.efi, SataOrom125.bin, SB.sdl
# 
# 22    10/25/12 8:17a Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Add new device and remove device which no use
# [Files]  		SBPEI.c, SB.sdl
# 
# 21    10/23/12 3:11a Scottyang
# [TAG]      EIP84560
# [Category] Bug Fix
# [Symptom]  Can't enter Win8 after Win8 AHCI driver version:11.5.0.1122
# install.
# [Solution] fixed in EIP84560
# [Files]    sb.sdl, sb.mak, sata.asl
# 
# 18    10/16/12 5:01a Scottyang
# [TAG]  		EIP84720
# [Category]  	Improvement
# [Description]  	Support Hot-Plug in Shark Bay
# [Files]  		PchRootPort.c, PchPcie.asl, PchPciExpressHelpersLib.mak,
# PchPciExpressHlpersLibrary.c, SB.sdl
# 
# 17    10/14/12 6:04a Scottyang
# [TAG]  		None
# [Category]  	Improvement
# [Description]  	Correct LNKA is 16
# 
# 16    10/12/12 4:54a Scottyang
# [TAG]  		EIP87695
# [Category]  	Improvement
# [Description]  	System should reboot successfully next time if S3
# resume fail
# [Files]  		SB.sdl, SBPei.c
# 
# 14    10/01/12 5:54a Victortu
# [TAG]           None
# [Category]      Improvement
# [Description]   Create new token "SOLUTION_FOR_EIP95440" for EIP#95440
# changed.
# [Files]         SB.sdl, SBDXE.c
# 
# 13    9/26/12 3:49a Victortu
# [TAG]           None
# [Category]      Improvement
# [Description]   If SPI Flash module support VSCC updated, skip
# programming VSCC.
# [Files]         SB.sdl, SBDxe.c
# 
# [TAG]           None
# [Category]      Improvement
# [Description]   Update from EIP#95440 to resolve the RAID driver
# compatibility issue.
# [Files]         SB.mak, SB.sdl, SBDXE.c
# 
# [TAG]           None
# [Category]      Improvement
# [Description]   Update for Intel PCH LPT RC070.
# [Files]         SB.sdl, SBDXE.c, SBPEI.c, Pch.sdl, SB.sd, SB.uni
# 
# [TAG]           None
# [Category]      Improvement
# [Description]   Update for PCH LP GPIO compatible.
# [Files]         SB.sdl, SB.H, AcpiModeEnable.c, AcpiModeEnable.sdl,
# SBDxe.c, SBGeneric.c, SBPEI.c, SBSMI.c, SleepSmi.c,
# SmiHandlerPorting.c, SmiHandlerPorting2.c
# 
# [TAG]           None
# [Category]      Improvement
# [Description]   Implement ULT platform LPSS and ADSP setup option.
# [Files]         GetSetupData.c, SB.sd, SB.uni, SbSetupData.h, SBDxe.c,
# SB.sdl
# 
# 12    9/12/12 5:11a Victortu
# [TAG]           None
# [Category]      Improvement
# [Description]   Remove useless HdmiVerbTable.
# [Files]         SB.sdl, SBCspLib.h, SBDxe.c, SBGeneric.c 
# 
# [TAG]           None
# [Category]      Improvement
# [Description]   Change "SB_TEMP_IO_BASE" to "0x1200".
# [Files]         SB.sdl
# 
# [TAG]           None
# [Category]      Improvement
# [Description]   Support OEM update VSCC table.
# [Files]         SB.H, SB.mak, SB.sdl, SBDXE.c
# 
# [TAG]           None
# [Category]      Improvement
# [Description]   Modify for Thunderbolt support.
# [Files]         GetSetupData.c, SB.sdl, SB.sd, SB.uni, SbSetupData.h,
# PciHotPlug.c
# 
# [TAG]           None
# [Category]      Improvement
# [Description]   Modify for ULT GPIO changed by PCH LPT-LP EDS 1.0.
# [Files]         SB.H, SB.sdl, AcpiModeEnable.c, AcpiModeEnable.sdl,
# SBPEI.c
# 
# 11    8/30/12 9:47a Victortu
# [TAG]           None
# [Category]      Improvement
# [Description]   Change "GPIO_BASE_ADDRESS" to "0x1C00".
# [Files]         SB.sdl
# 
# [TAG]           None
# [Category]      Improvement
# [Description]   Update "GPE0_BLK_ADDRESS" and "GPE0_BLK_LENGTH" for
# RTD3 support.
# [Files]         SB.sdl
# 
# [TAG]           None
# [Category]      Improvement
# [Description]   Fixed building error when disable all PCI slots.
# [Files]         SB.sdl
# 
# 10    8/24/12 6:48a Victortu
# [TAG]           None
# [Category]      Improvement
# [Description]   Remove useless SB_SHADOW_CONTROL.
# [Files]         SB.sdl, SBCspLib.h, SBGeneric.c
# 
# [TAG]           None
# [Category]      Improvement
# [Description]   Update RC_PORT_x for PCIe.
# [Files]         SB.sdl, SB.sd, SBDxe.c
# 
# [TAG]           None
# [Category]      Improvement
# [Description]   Corrected EHCI_MMIO_BASE_ADDRESS1 to fix system hang at
# 0x71 when AMI_DEBUGGER_SUPPORT.
# [Files]         SB.sdl
# 
# 9     8/15/12 1:11a Victortu
# [TAG]           None
# [Category]      Improvement
# [Description]   Update "SB_TEMP_MMIO_BASE" and
# "EHCI_MMIO_BASE_ADDRESS".
# [Files]         SB.sdl, SBDxe.c, SBPEI.c
# 
# 8     8/13/12 10:14a Victortu
# [TAG]           None
# [Category]      Improvement
# [Description]   Remove ThimblePeak 1/2/3.
# [Files]         SB.sdl
# 
# [TAG]           None
# [Category]      Improvement
# [Description]   Create the token "USB30_OVER_CURRENT_MAPPING_SETTINGS"
# for the policy "Usb30OverCurrentPins".
# [Files]         SB.sdl, SBDxe.c
# 
# [TAG]           None
# [Category]      Improvement
# [Description]   Changed PM Base Address from 0x400 to 0x1800.
# [Files]         SB.sdl
# 
# [TAG]           None
# [Category]      Improvement
# [Description]   Update PCH Policy.
# [Files]         SB.sdl, SBDxe.c, SBPEI.c
# 
# 7     7/27/12 6:02a Victortu
# Update setup items and policies.
# 
# 6     7/02/12 10:21a Victortu
# [TAG]		None
# [Category]	Improvement
# [Description]	Updated and modified for PCH RC 0.6.0.
# [Files]		SBGeneric.c, SB.sdl, SBCspLib.h, SBDxe.c, SBPEI.c
# 
# 5     6/13/12 11:33p Victortu
# [TAG]           None
# [Category]      Improvement
# [Description]   Implement Warm Boot function for Secure Flash feature.
# [Files]         SB.H, SB.mak, SB.sdl, SBDxe.c, SBGeneric.c, SBPEI.c,
# SBSMI.c
# 
# 4     5/03/12 6:32a Victortu
# [TAG]           None 
# [Category]      Improvement 
# [Description]   Modify to support Thunderbolt. 
# [Files]         SB.sd; SB.uni; SB.sdl; SbSetupData.h; PciHotPlug.c 
# 
# 3     3/22/12 10:22a Victortu
# [TAG]		None
# [Category]	Improvement
# [Description]	Rename SataOpROM. Notice : This SataOrom120.bin file is
# dummy
# [Files]		SB.sdl, SataOrom120.bin, sbCSP.CIF
# 
# [TAG]		None
# [Category]	Bug Fix
# [Severity]		Normal
# [Symptom]	System hang up if enable "DEBUG_MODE"
# [Solution]		Set "USB_PORTS_LENGTH" to 0x80 as default
# [Files]		SB.sdl
# 
# 2     2/20/12 4:21a Yurenlai
# [TAG]         None
# [Category]    Improvement
# [Description] Fill in a temp value for token "USB_PORTS_LENGTH".
# [Files]       SB.sdl
# 
# 1     2/08/12 8:22a Yurenlai
# Intel Lynx Point/SB eChipset initially releases.
#
#*************************************************************************

IRQLINK
	Name  = "LNKA"
	Reg  = 060h
	IrqList  = 3,4,5,6,10,11,12,14,15
	InterruptType = LevelLow
End

IRQLINK
	Name  = "LNKB"
	Reg  = 061h
	IrqList  = 3,4,5,6,10,11,12,14,15
	InterruptType = LevelLow
End

IRQLINK
	Name  = "LNKC"
	Reg  = 062h
	IrqList  = 3,4,5,6,10,11,12,14,15
	InterruptType = LevelLow
End

IRQLINK
	Name  = "LNKD"
	Reg  = 063h
	IrqList  = 3,4,5,6,10,11,12,14,15
	InterruptType = LevelLow
End

IRQLINK
	Name  = "LNKE"
	Reg  = 068h
	IrqList  = 3,4,5,6,10,11,12,14,15
	InterruptType = LevelLow
End

IRQLINK
	Name  = "LNKF"
	Reg  = 069h
	IrqList  = 3,4,5,6,10,11,12,14,15
	InterruptType = LevelLow
End

IRQLINK
	Name  = "LNKG"
	Reg  = 06ah
	IrqList  = 3,4,5,6,10,11,12,14,15
	InterruptType = LevelLow
End

IRQLINK
	Name  = "LNKH"
	Reg  = 06bh
	IrqList  = 3,4,5,6,10,11,12,14,15
	InterruptType = LevelLow
End

PCIDEVICE
	Title  = "LPC Bridge"
	Bus  = 00h
	Dev  = 01fh
	Fun  = 00h
	ASLfile  = "$(INTEL_ACPI_ASL_DIR)\Lpcb.ASL"
	ASLdeviceName  = "LPCB"
	IntA = 	LNKF; 21
	IntB = 	LNKD; 19
	IntC = 	LNKC; 18
	IntD = 	LNKA; 16
	DeviceType = OnBoard
	PCIBusSize = 32bit
	LPCBridge = Yes
	PWRBwake = Yes
	ROMMain = No
End

PCIDEVICE
	Title  = "SATA #0"
	Bus  = 00h
	Dev  = 01fh
	Fun  = 02h
	IntB = 	LNKD; 19
	DeviceType = OnBoard
	PCIBusSize = 32bit
	ROMMain = No
End

PCIDEVICE
	Title  = "SATA #1"
	Bus  = 00h
	Dev  = 01fh
	Fun  = 05h
	IntB = 	LNKD; 19
	DeviceType = OnBoard
	PCIBusSize = 32bit
	ROMMain = No
End

PCIDEVICE
	Title  = "SATA RAID Controller(Mobile)"
	Bus  = 00h
	Dev  = 01fh
	Fun  = 02h
	ROMFile  = "Chipset\SB\SataOrom125.bin"
	DeviceID  = 0282ah
	VendorID  = 08086h
	IntB = 	LNKD; 19
	DeviceType = OnBoard
	PCIBusSize = 32bit
	OptionROM = Yes
	CompressedROM = Yes
	Token = "PCH_SKU" "=" "1"
End

PCIDEVICE
	Title  = "SATA RAID Controller(Desktop)"
	Bus  = 00h
	Dev  = 01fh
	Fun  = 02h
	ROMFile  = "Chipset\SB\SataOrom125.bin"
	DeviceID  = 02822h
	VendorID  = 08086h
	IntB = 	LNKD; 19
	DeviceType = OnBoard
	PCIBusSize = 32bit
	OptionROM = Yes
	CompressedROM = Yes
	Token = "PCH_SKU" "=" "0"
End

PCIDEVICE
	Title  = "SMBus Controller"
	Bus  = 00h
	Dev  = 01fh
	Fun  = 03h
	IntC = 	LNKC; 18
	DeviceType = OnBoard
	PCIBusSize = 32bit
End

PCIDEVICE
	Title  = "Thermal Controller"
	Bus  = 00h
	Dev  = 01fh
	Fun  = 06h
	IntC = 	LNKC; 18
	DeviceType = OnBoard
	PCIBusSize = 32bit
End

PCIDEVICE
	Title  = "XHCI Controller"
	Bus  = 00h
	Dev  = 014h
	Fun  = 00h
	IntA = 	LNKA; 16
	DeviceType = OnBoard
	PCIBusSize = 32bit
End

PCIDEVICE
	Title  = "EHCI #0"
	Bus  = 00h
	Dev  = 01dh
	Fun  = 00h
	IntA = 	LNKH; 23
	DeviceType = OnBoard
	PCIBusSize = 32bit
End

PCIDEVICE
	Title  = "EHCI #1"
	Bus  = 00h
	Dev  = 01ah
	Fun  = 00h
	IntA = 	LNKA; 16
	DeviceType = OnBoard
	PCIBusSize = 32bit
End

PCIDEVICE
	Title  = "High Definition Audio"
	Bus  = 00h
	Dev  = 01bh
	Fun  = 00h
	IntA = 	LNKG; 22
	DeviceType = OnBoard
	PCIBusSize = PciEx
	ROMMain = No
End

PCIDEVICE
	Title  = "GbE Controller"
	Bus  = 00h
	Dev  = 019h
	Fun  = 00h
	ROMFile  = "Chipset\SB\GbE_OR.BIN"
	DeviceID  = 01502h
	VendorID  = 08086h
	IntA = 	LNKE; 20
	DeviceType = OnBoard
	PCIBusSize = 32bit
	OptionROM = Yes
	CompressedROM = Yes
	LinkDevice = Yes
End

PCIDEVICE
	Title  = "ME"
	Bus  = 00h
	Dev  = 016h
	IntA = 	LNKA; 16
	IntB = 	LNKD; 19
	IntC = 	LNKC; 18
	IntD = 	LNKB; 17
	DeviceType = OnBoard
	PCIBusSize = 32bit
	ROMMain = No
End

PCIDEVICE
	Title  = "PCIE Root Port #1"
	Bus  = 00h
	Dev  = 01ch
	Fun  = 00h
	BridgeBus  = 04h
	GPEbit  = 09h
	SleepNum  = 04h
	ASLfile  = "$(PchAcpiTables_DIR)\PchPcie.asl"
	ASLdeviceName  = "RP01"
	IntA = 	LNKA; 16
	IntB = 	LNKB; 17
	IntC = 	LNKC; 18
	IntD = 	LNKD; 19
	Token = "RC_PORT_0" "=" "1"
	DeviceType = OnBoard
	PCIBusSize = PciEx
	PCIBridge = Yes
	ROMMain = No
End

PCIDEVICE
	Title  = "PCIE Root Port #2"
	Bus  = 00h
	Dev  = 01ch
	Fun  = 01h
	BridgeBus  = 05h
	GPEbit  = 09h
	SleepNum  = 04h
	ASLfile  = "$(PchAcpiTables_DIR)\PchPcie.asl"
	ASLdeviceName  = "RP02"
	Token = "RC_PORT_0" "=" "1"
	Token = "RC_PORT_1" "=" "1"
	DeviceType = OnBoard
	PCIBusSize = PciEx
	PCIBridge = Yes
End

PCIDEVICE
	Title  = "PCIE Root Port #3"
	Bus  = 00h
	Dev  = 01ch
	Fun  = 02h
	BridgeBus  = 06h
	GPEbit  = 09h
	SleepNum  = 04h
	ASLfile  = "$(PchAcpiTables_DIR)\PchPcie.asl"
	ASLdeviceName  = "RP03"
	Token = "RC_PORT_0" "=" "1"
	Token = "RC_PORT_2" "=" "1"
	DeviceType = OnBoard
	PCIBusSize = PciEx
	PCIBridge = Yes
End

PCIDEVICE
	Title  = "PCIE Root Port #4"
	Bus  = 00h
	Dev  = 01ch
	Fun  = 03h
	BridgeBus  = 07h
	GPEbit  = 09h
	SleepNum  = 04h
	ASLfile  = "$(PchAcpiTables_DIR)\PchPcie.asl"
	ASLdeviceName  = "RP04"
	Token = "RC_PORT_0" "=" "1"
	Token = "RC_PORT_3" "=" "1"
	DeviceType = OnBoard
	PCIBusSize = PciEx
	PCIBridge = Yes
End

PCIDEVICE
	Title  = "PCIE Root Port #5"
	Bus  = 00h
	Dev  = 01ch
	Fun  = 04h
	BridgeBus  = 08h
	GPEbit  = 09h
	SleepNum  = 04h
	ASLfile  = "$(PchAcpiTables_DIR)\PchPcie.asl"
	ASLdeviceName  = "RP05"
	Token = "RC_PORT_0" "=" "1"
	Token = "RC_PORT_4" "=" "1"
	DeviceType = OnBoard
	PCIBusSize = PciEx
	PCIBridge = Yes
End

PCIDEVICE
	Title  = "PCIE Root Port #6"
	Bus  = 00h
	Dev  = 01ch
	Fun  = 05h
	BridgeBus  = 09h
	GPEbit  = 09h
	SleepNum  = 04h
	ASLfile  = "$(PchAcpiTables_DIR)\PchPcie.asl"
	ASLdeviceName  = "RP06"
	Token = "RC_PORT_0" "=" "1"
	Token = "RC_PORT_5" "=" "1"
	DeviceType = OnBoard
	PCIBusSize = PciEx
	PCIBridge = Yes
End

PCIDEVICE
	Title  = "PCIE Root Port #7"
	Bus  = 00h
	Dev  = 01ch
	Fun  = 06h
	BridgeBus  = 0eh
	GPEbit  = 09h
	SleepNum  = 04h
	ASLfile  = "$(PchAcpiTables_DIR)\PchPcie.asl"
	ASLdeviceName  = "RP07"
	Token = "RC_PORT_0" "=" "1"
	Token = "RC_PORT_6" "=" "1"
	DeviceType = OnBoard
	PCIBusSize = PciEx
	PCIBridge = Yes
End

PCIDEVICE
	Title  = "PCIE Root Port #8"
	Bus  = 00h
	Dev  = 01ch
	Fun  = 07h
	BridgeBus  = 0fh
	GPEbit  = 09h
	SleepNum  = 04h
	ASLfile  = "$(PchAcpiTables_DIR)\PchPcie.asl"
	ASLdeviceName  = "RP08"
	Token = "RC_PORT_0" "=" "1"
	Token = "RC_PORT_7" "=" "1"
	DeviceType = OnBoard
	PCIBusSize = PciEx
	PCIBridge = Yes
End

PCIDEVICE
	Title  = "PCIE Port #1 Slot"
	Bus  = 04h
	Dev  = 00h
	Slot  = 021h
	IntA = 	LNKA; 16
	IntB = 	LNKB; 17
	IntC = 	LNKC; 18
	IntD = 	LNKD; 19
	Token = "RC_PORT_0" "=" "1"
	DeviceType = Slot
	PCIBusSize = PciEx
End

PCIDEVICE
	Title  = "PCIE Port #2 Slot"
	Bus  = 05h
	Dev  = 00h
	Slot  = 022h
	IntA = 	LNKB; 17
	IntB = 	LNKC; 18
	IntC = 	LNKD; 19
	IntD = 	LNKA; 16
	Token = "RC_PORT_0" "=" "1"
	Token = "RC_PORT_1" "=" "1"
	DeviceType = Slot
	PCIBusSize = PciEx
End

PCIDEVICE
	Title  = "PCIE Port #3 Slot"
	Bus  = 06h
	Dev  = 00h
	Slot  = 08h
	IntA = 	LNKC; 18
	IntB = 	LNKD; 19
	IntC = 	LNKA; 16
	IntD = 	LNKB; 17
	Token = "RC_PORT_0" "=" "1"
	Token = "RC_PORT_2" "=" "1"
	DeviceType = Slot
	PCIBusSize = PciEx
End

PCIDEVICE
	Title  = "PCIE Port #4 Slot"
	Bus  = 07h
	Dev  = 00h
	Slot  = 09h
	IntA = 	LNKD; 19
	IntB = 	LNKA; 16
	IntC = 	LNKB; 17
	IntD = 	LNKC; 18
	Token = "RC_PORT_0" "=" "1"
	Token = "RC_PORT_3" "=" "1"
	DeviceType = Slot
	PCIBusSize = PciEx
End

PCIDEVICE
	Title  = "PCIE Port #5 Slot"
	Bus  = 08h
	Dev  = 00h
	Slot  = 0ah
	IntA = 	LNKA; 16
	IntB = 	LNKB; 17
	IntC = 	LNKC; 18
	IntD = 	LNKD; 19
	Token = "RC_PORT_0" "=" "1"
	Token = "RC_PORT_4" "=" "1"
	DeviceType = Slot
	PCIBusSize = PciEx
End

PCIDEVICE
	Title  = "PCIE Port #6 Slot"
	Bus  = 09h
	Dev  = 00h
	Slot  = 010h
	IntA = 	LNKB; 17
	IntB = 	LNKC; 18
	IntC = 	LNKD; 19
	IntD = 	LNKA; 16
	Token = "RC_PORT_0" "=" "1"
	Token = "RC_PORT_5" "=" "1"
	DeviceType = Slot
	PCIBusSize = PciEx
End

PCIDEVICE
	Title  = "PCIE Port #7 Slot"
	Bus  = 0eh
	Dev  = 00h
	Slot  = 011h
	IntA = 	LNKC; 18
	IntB = 	LNKD; 19
	IntC = 	LNKA; 16
	IntD = 	LNKB; 17
	Token = "RC_PORT_0" "=" "1"
	Token = "RC_PORT_6" "=" "1"
	DeviceType = Slot
	PCIBusSize = PciEx
End

PCIDEVICE
	Title  = "PCIE Port #8 Slot"
	Bus  = 0fh
	Dev  = 00h
	Slot  = 012h
	IntA = 	LNKD; 19
	IntB = 	LNKA; 16
	IntC = 	LNKB; 17
	IntD = 	LNKC; 18
	Token = "RC_PORT_0" "=" "1"
	Token = "RC_PORT_7" "=" "1"
	DeviceType = Slot
	PCIBusSize = PciEx
End

PCIDEVICE
	Title  = "DMA Controller"
	Bus  = 00h
	Dev  = 015h
	Fun  = 00h
	IntB = 	LNKE; 20
	DeviceType = OnBoard
	PCIBusSize = 32bit
	Token = "ULT_SUPPORT" "=" "1"
End

PCIDEVICE
	Title  = "I2c0"
	Bus  = 00h
	Dev  = 015h
	Fun  = 01h
	IntC = 	LNKF; 21
	DeviceType = OnBoard
	PCIBusSize = 32bit
	Token = "ULT_SUPPORT" "=" "1"
End

PCIDEVICE
	Title  = "I2c1"
	Bus  = 00h
	Dev  = 015h
	Fun  = 02h
	IntC = 	LNKF; 21
	DeviceType = OnBoard
	PCIBusSize = 32bit
	Token = "ULT_SUPPORT" "=" "1"
End

PCIDEVICE
	Title  = "SPI0"
	Bus  = 00h
	Dev  = 015h
	Fun  = 03h
	IntC = 	LNKF; 21
	DeviceType = OnBoard
	PCIBusSize = 32bit
	Token = "ULT_SUPPORT" "=" "1"
End

PCIDEVICE
	Title  = "SPI1"
	Bus  = 00h
	Dev  = 015h
	Fun  = 04h
	IntC = 	LNKF; 21
	DeviceType = OnBoard
	PCIBusSize = 32bit
	Token = "ULT_SUPPORT" "=" "1"
End

PCIDEVICE
	Title  = "UART0"
	Bus  = 00h
	Dev  = 015h
	Fun  = 05h
	IntD = 	LNKF; 21
	DeviceType = OnBoard
	PCIBusSize = 32bit
	Token = "ULT_SUPPORT" "=" "1"
End

PCIDEVICE
	Title  = "UART1"
	Bus  = 00h
	Dev  = 015h
	Fun  = 06h
	IntD = 	LNKF; 21
	DeviceType = OnBoard
	PCIBusSize = 32bit
	Token = "ULT_SUPPORT" "=" "1"
End

PCIDEVICE
	Title  = "SDIO"
	Bus  = 00h
	Dev  = 017h
	Fun  = 00h
	IntA = 	LNKG; 22
	DeviceType = OnBoard
	PCIBusSize = 32bit
	Token = "ULT_SUPPORT" "=" "1"
End

PCIDEVICE
	Title  = "Audio DSP"
	Bus  = 00h
	Dev  = 013h
	Fun  = 00h
	IntA = 	LNKH; 23
	DeviceType = OnBoard
	PCIBusSize = 32bit
	Token = "ULT_SUPPORT" "=" "1"
End

IOAPIC
	Title  = "IO APIC"
	APICID  = 02h
	VectorBase  = 00h
	VectorRange  = 017h
	AddressBase  = 0fec00000h
End

TOKEN
	Name  = "SB_SUPPORT"
	Value  = "1"
	Help  = "Main switch to enable Template - SouthBridge support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	Master = Yes
End

TOKEN
	Name  = "SB_TEMPLATE_VER"
	Value  = "0006"
	Help  = "South Bridge Template Version Number.\ DO NOT CHANGE THIS VALUE"
	TokenType = Integer
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name  = "SB_DEBUG_MESSAGE"
	Value  = "1"
	Help  = "Enables/disables debug message in SB module"
	TokenType = Boolean
	TargetEQU = Yes
	TargetH = Yes
	Token = "DEBUG_MODE" "!=" "0"
End

TOKEN
	Name  = "SB_RESET_PPI_SUPPORT"
	Value  = "1"
	Help  = "Enable this token if reset PPI is from south bridge.\ If not disable this and provide reset functionality from other PEIM."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "COLD_RESET_WITH_POWER_CYCLE"
	Value  = "0"
	Help  = "Enable this token for EfiResetCold do full reset.\ If not disable this and provide EfiResetCold do hard reset."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "SB_STALL_PPI_SUPPORT"
	Value  = "1"
	Help  = "Enable this token if Stall PPI is from south bridge.\ If not disable this and provide reset functionality from other PEIM."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "OEM_UPDATE_VSCC_TABLE_SUPPORT"
	Value  = "1"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "OEM_UPDATE_VSCC_TABLE_SUPPORT"
	Value  = "0"
	TokenType = Boolean
	TargetH = Yes
	Token = "SPI_INITIALIZE_WITH_VSCC" "=" "1"
End

TOKEN
	Name  = " "
	TokenType = Integer
End

TOKEN
	Name  = "=============== SB Specific Tokens =============="
	TokenType = Expression
End

TOKEN
	Name  = "ENABLE_RTC_ONE_SECOND_WAKEUP"
	Value  = "0"
	Help  = "1: Setups RTC 1 second alarm as well."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "PERFORM_KBC_RESET"
	Value  = "0"
	Help  = "WARNING: When this token is enabled, it might pull down the system boot speed."
	TokenType = Boolean
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "HECI_BASE_ADDRESS"
	Value  = "0xFEDB0000"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "HECI2_BASE_ADDRESS"
	Value  = "0xFEDC0000"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "SMBUS_BASE_ADDRESS"
	Value  = "0x0580"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "SMBS"
	Value  = "$(SMBUS_BASE_ADDRESS)"
	Help  = "SMBus I/O Registes Base Address"
	TokenType = Integer
	TargetASL = Yes
	TargetH = Yes
End

TOKEN
	Name  = "SMBL"
	Value  = "0x20"
	Help  = "SMBus I/O Registes Range"
	TokenType = Integer
	TargetASL = Yes
	TargetH = Yes
End

TOKEN
	Name  = "SB_PIRQ_ROUTER_VID"
	Value  = "0x8086"
	Help  = "IRQ Router Vendor ID. \PLEASE CHANGE THIS AS PER CHIPSET"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "SB_PIRQ_ROUTER_DID"
	Value  = "0x27B8"
	Help  = "IRQ Router Device ID. \PLEASE CHANGE THIS AS PER CHIPSET"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "SPI_BASE_ADDRESS"
	Value  = "0x3800"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "PM_BASE_ADDRESS"
	Value  = "0x1800"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "PBLK"
	Value  = "$(PM_BASE_ADDRESS) + 10h"
	Help  = "Boot-starp CPU Control Block register address. Use return value of PM_BASE_ADDRESS with proper offset.\Value can be returned by CPUx_PBLK tokens, x is the Processor index the PBLK is wired to.\Example : $(PM_BASE_ADDRESS) + 10h\"
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
	Range  = "16-bit IO register"
End

TOKEN
	Name  = "PMBS"
	Value  = "$(PM_BASE_ADDRESS)"
	Help  = "ASL alias for ACPI I/O base address."
	TokenType = Integer
	TargetASL = Yes
End

TOKEN
	Name  = "PMLN"
	Value  = "0x100"
	Help  = "Power Management registers block length"
	TokenType = Integer
	TargetASL = Yes
	TargetH = Yes
End

TOKEN
	Name  = "TCO_BASE_ADDRESS"
	Value  = "$(PM_BASE_ADDRESS) + 60h"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "GPIO_BASE_ADDRESS"
	Value  = "0x1C00"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "GPI_IRQ_2_IOXAPIC"
	Value  = "0xFFFF"
	Help  = "Enable the corresponding GPIO PIRQ pin to generate IOxAPIC interrupt for PchLp"
	TokenType = Integer
	Range  = "{0-0xFFFF}"
	TargetMAK = Yes
	TargetH = Yes
End

TOKEN
	Name  = "GPBS"
	Value  = "$(GPIO_BASE_ADDRESS)"
	Help  = "ASL alias for General Purpose I/O base address."
	TokenType = Integer
	TargetASL = Yes
End

TOKEN
	Name  = "GPLN"
	Value  = "0x400"
	Help  = "GP I/O Registes Range"
	TokenType = Integer
	TargetASL = Yes
	TargetH = Yes
End

TOKEN
	Name  = "SW_SMI_IO_ADDRESS"
	Value  = "0xb2"
	Help  = "PLEASE CHANGE THIS VALUE AS PER PM_BASE_ADDRESS"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "SW_SMI_IO_DATA_ADDRESS"
	Value  = "0xb3"
	Help  = "PLEASE CHANGE THIS VALUE AS PER PM_BASE_ADDRESS"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "SMIP"
	Value  = "$(SW_SMI_IO_ADDRESS)"
	Help  = "Token to go to ASL Name Definitions"
	TokenType = Integer
	TargetASL = Yes
End

TOKEN
	Name  = "PCH_SKU"
	Value  = "1"
	Help  = "0:Desktop, Workstation\1:Mobile\2:UP Server"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "COUGAR_POINT_SKU"
	Value  = "$(PCH_SKU)"
	Help  = "0:Desktop, Workstation\1:Mobile\2:UP Server"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "SPI_READ_CONFIG"
	Value  = "2"
	Help  = "0:No prefetching, but caching enabled.\1:No prefetching and no caching.\2:Prefetching and Caching enabled."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "HIDE_BIOS_SECURITY_PAGE"
	Value  = "0"
	Help  = "Hide Bios security page in the setup."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "SMI_LOCK_ENABLE"
	Value  = "1"
	Help  = "0:Set the default value to 'Disabled'.\1:Set the default value to 'Enabled'.\B0:D31:F0:A0h[4]"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "BIOS_INTERFACE_LOCKDOWN"
	Value  = "1"
	Help  = "0:Set the default value to 'Disabled'.\1:Set the default value to 'Enabled'.\BLE, RCBA + 3410h[0]"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "GPIO_LOCKDOWN_ENABLE"
	Value  = "0"
	Help  = "0:Set the default value to 'Disabled'.\1:Set the default value to 'Enabled'.\GLE, B0:D31:F0:4Ch[0]"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "BIOS_LOCK_ENABLE"
	Value  = "1"
	Help  = "0:Set the default value to 'Disabled'.\1:Set the default value to 'Enabled'."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "RTC_LOCK_ENABLE"
	Value  = "0"
	Help  = "0:Set the default value to 'Disabled'.\1:Set the default value to 'Enabled'."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "ROOT_PORT_FUN_SWAP_ENABLE"
	Value  = "0"
	Help  = "0:Set the default value to 'Disabled'.\1:Set the default value to 'Enabled'."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "DEFAULT_CRID_ENABLE"
	Value  = "0"
	Help  = "1:Enable CRID feature/0:Disable CRID feature"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
End

TOKEN
	Name  = "PCH_PWR_OPT_DMI"
	Value  = "1"
	Help  = "0:Set the function to 'Disabled'.\1:Set the function to 'Enabled'."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "PCH_PWR_OPT_GBE"
	Value  = "1"
	Help  = "0:Set the function to 'Disabled'.\1:Set the function to 'Enabled'."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "PCH_PWR_OPT_XHCI"
	Value  = "0"
	Help  = "0:Set the function to 'Disabled'.\1:Set the function to 'Enabled'."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "PCH_PWR_OPT_EHCI"
	Value  = "0"
	Help  = "0:Set the function to 'Disabled'.\1:Set the function to 'Enabled'."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "PCH_PWR_OPT_SATA"
	Value  = "1"
	Help  = "0:Set the function to 'Disabled'.\1:Set the function to 'Enabled'."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "MEM_CLOSE_STATE_EN"
	Value  = "1"
	Help  = "0:Set the function to 'Disabled'.\1:Set the function to 'Enabled'."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "INTERNAL_OBFF_EN"
	Value  = "1"
	Help  = "0:Set the function to 'Disabled'.\1:Set the function to 'Enabled'."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "NUM_OF_DEVLTR_OVERRID"
	Value  = "0"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "DEVLTR_OVERRID"
	Value  = "0"
	Help  = "0:Set the function to 'Disabled'.\1:Set the function to 'Enabled'."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "LEGACY_DMA_DISABLE"
	Value  = "0"
	Help  = "0:Legacy DMA is enable.\1:Legacy DMA is disable.\Supported in PCH RC v1.4.0."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "USB_PORTS_LENGTH"
	Value  = "0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80"
	Help  = "0x33 = 3.3 inch, 0x146 = 14.6 inch ...."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "USB_OVER_CURRENT_MAPPING_SETTINGS"
	Value  = "0, 0, 1, 1, 2, 2, 3, 3, 4, 4, 5, 5, 6, 6"
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "ULT_USB_OVER_CURRENT_MAPPING_SETTINGS"
	Value  = "0, 0, 8, 8, 2, 2, 1, 1"
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "USB30_OVER_CURRENT_MAPPING_SETTINGS"
	Value  = "0, 0, 1, 1, 2, 2"
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "USB_PORT_LOCATION_CONFIG"
	Value  = "1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1"
	Help  = "BIT0 = Port0; BIT1 = Port1 ... ; BIT13 = Port13\0:BackPanel\1:FrontPanel\2:Dock\3:MiniPciE\4:Flex\5:InternalTopology\6:Skip\7:Max"
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "EHCI_CON_DISCON_WAKE_UP_SUPPORT"
	Value  = "0"
	Help  = "WARNING: Not all OS support this function, for more detail please refer to Intel PCH Spec. 12.8 Platform Controller Hub (PCH) USB 2.0 Wake On Connect / Disconnect Handling and PCH EDS RMHWKCTL - Rate Matching Hub Wake Control Reg (PCH EDS RCBA + 35B0h)."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "OEM_USB_PER_PORT_DISABLE_SUPPORT"
	Value  = "0"
	Help  = "USB per-port disable function will execute at ready to boot. USB device can use at setup when port is disable but not at OS, DOS or Shell."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "SB_PCI_DEVICES_SSID_TABLE"
	Value  = "{HECI_BUS_DEV_FUN, -1}, {HECI2_BUS_DEV_FUN, -1}, {IDER_BUS_DEV_FUN, -1}, {KT_BUS_DEV_FUN, -1}, {LAN_BUS_DEV_FUN, -1}, {XHCI_BUS_DEV_FUN, -1}, {EHCI2_BUS_DEV_FUN, -1}, {HDA_BUS_DEV_FUN, -1}, {PCIEBRS_BUS_DEV_FUN, -1}, {PCIEBRS2_BUS_DEV_FUN, -1}, {PCIEBRS3_BUS_DEV_FUN, -1}, {PCIEBRS4_BUS_DEV_FUN, -1}, {PCIEBRS5_BUS_DEV_FUN, -1}, {PCIEBRS6_BUS_DEV_FUN, -1}, {PCIEBRS7_BUS_DEV_FUN, -1}, {PCIEBRS8_BUS_DEV_FUN, -1}, {EHCI_BUS_DEV_FUN, -1}, {PCIBR_BUS_DEV_FUN, -1}, {SB_BUS_DEV_FUN, -1}, {SATA_BUS_DEV_FUN, -1}, {SMBUS_BUS_DEV_FUN, -1}, {SATA2_BUS_DEV_FUN, -1}, {THERMAL_BUS_DEV_FUN, -1}, {-1, -1}"
	Help  = "List of PCI device's Sub-System ID in the following format:\{Device#1 Bus/Device/Function, Device#1 Sub-ID}, {Device#2 Bus/Device/Function, Device#2 Sub-ID}...\The format of the PCI bus/device/function is followed by EFI_PCI_CONFIGURATION_ADDRESS.\If the value of Sub-ID is -1, that means BIOS will use PCI Vendor-ID and Device-ID instead.\The last structure {-1, -1} is end of the table, don't remove it!"
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "SB_PCI_DEVICES_SSID_TABLE"
	Value  = "{SIO_DMA_BUS_DEV_FUN, -1}, {SIO_I2C0_BUS_DEV_FUN, -1}, {SIO_I2C1_BUS_DEV_FUN, -1}, {SIO_GSPI0_BUS_DEV_FUN, -1}, {SIO_GSPI1_BUS_DEV_FUN, -1}, {SIO_UART0_BUS_DEV_FUN, -1}, {SIO_UART1_BUS_DEV_FUN, -1}, {SIO_SDIO_BUS_DEV_FUN, -1}, {HECI_BUS_DEV_FUN, -1}, {HECI2_BUS_DEV_FUN, -1}, {IDER_BUS_DEV_FUN, -1}, {KT_BUS_DEV_FUN, -1}, {LAN_BUS_DEV_FUN, -1}, {XHCI_BUS_DEV_FUN, -1}, {EHCI2_BUS_DEV_FUN, -1}, {HDA_BUS_DEV_FUN, -1}, {PCIEBRS_BUS_DEV_FUN, -1}, {PCIEBRS2_BUS_DEV_FUN, -1}, {PCIEBRS3_BUS_DEV_FUN, -1}, {PCIEBRS4_BUS_DEV_FUN, -1}, {PCIEBRS5_BUS_DEV_FUN, -1}, {PCIEBRS6_BUS_DEV_FUN, -1}, {PCIEBRS7_BUS_DEV_FUN, -1}, {PCIEBRS8_BUS_DEV_FUN, -1}, {EHCI_BUS_DEV_FUN, -1}, {PCIBR_BUS_DEV_FUN, -1}, {SB_BUS_DEV_FUN, -1}, {SATA_BUS_DEV_FUN, -1}, {SMBUS_BUS_DEV_FUN, -1}, {SATA2_BUS_DEV_FUN, -1}, {THERMAL_BUS_DEV_FUN, -1}, {-1, -1}"
	Help  = "List of PCI device's Sub-System ID in the following format:\{Device#1 Bus/Device/Function, Device#1 Sub-ID}, {Device#2 Bus/Device/Function, Device#2 Sub-ID}...\The format of the PCI bus/device/function is followed by EFI_PCI_CONFIGURATION_ADDRESS.\If the value of Sub-ID is -1, that means BIOS will use PCI Vendor-ID and Device-ID instead.\The last structure {-1, -1} is end of the table, don't remove it!"
	TokenType = Expression
	TargetH = Yes
	Token = "ULT_SUPPORT" "=" "1"
End

TOKEN
	Name  = "TSGPIO_C_PMSYN"
	Value  = "1"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "TSGPIO_D_PMSYN"
	Value  = "1"
        Help  = "0:Disable\1:Enable"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "TSGPIO_C_C0_TRANSMIT"
	Value  = "1"
        Help  = "0:Disable\1:Enable"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "TSGPIO_D_C0_TRANSMIT"
	Value  = "1"
        Help  = "0:Disable\1:Enable"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "TSGPIO_C_PIN_SEL"
	Value  = "1"
	TokenType = Integer
	TargetH = Yes
	Range = "0-1"
End

TOKEN
	Name  = "TSGPIO_D_PIN_SEL"
	Value  = "0"
	TokenType = Integer
	TargetH = Yes
	Range = "0-1"
End

TOKEN
	Name = "DEVICE_NAME_LENGTH"
	Value = "14"
	Help = "ATA/ATAPI Device name length, this token is defined the maximum characters of the device name will be showed on SETUP."
	TokenType = Integer
	TargetH = Yes
	Range = "2-41"
End

TOKEN
	Name = "SB_SWSMI_WRITE_TO_BOOTSCRIPT"
	Value = "0"
	Help = "0: Software SMI SW_SMI_ACPI_ENABLE and SW_SMI_SB_ACPI_S3 will be written to boot script in CSM module.\1: Software SMI SW_SMI_ACPI_ENABLE and SW_SMI_SB_ACPI_S3 will be written to boot script in SB eChipset."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name = "SB_SWSMI_WRITE_TO_BOOTSCRIPT"
	Value = "1"
	Help = "0: Software SMI SW_SMI_ACPI_ENABLE and SW_SMI_SB_ACPI_S3 will be written to boot script in CSM module.\1: Software SMI SW_SMI_ACPI_ENABLE and SW_SMI_SB_ACPI_S3 will be written to boot script in SB eChipset."
	TokenType = Boolean
	TargetH = Yes
        Token = "LegacyInterrupt_SUPPORT" "=" "0"
End

TOKEN
	Name = "PCH_IO_APIC_ID"
	Value = "02"
	Help = "Assign IO APIC ID"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name = "PCH_APIC_RANGE_SELECT"
	Value = "0"
	Help = "Program APIC Range Select bits at RCBA + 31FEh[7:0]"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name = "HDA_RESET_WAIT_TIMER"
	Value = "300"
	Help = "Minimum link timing requirements."
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name = "ME_WAKE_STS"
	Value = "1"
	Help = "Clear Intel ME WAKE STATUS."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name = "ME_HRST_COLD_STS"
	Value = "1"
	Help = "Clear Intel ME Host Reset Cold Status."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name = "ME_HRST_WARM_STS"
	Value = "1"
	Help = "Clear Intel ME Host Reset Warm Status"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name = "PCH_SLP_S3_MIN_ASSERT_VALUE"
	Value = "2"
	Help = "SLP_S3# Stretch\0:60us\1:1ms\2:50ms\3:2s"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name = "PCH_SLP_SUS_MIN_ASSERT_VALUE"
	Value = "3"
	Help = "SLP_SUS# Minimum Assertion Width.\0:0ms\1:500ms\2:1s\3:4s"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name = "PCH_SLPA_MIN_ASSERT_VALUE"
	Value = "3"
	Help = "SLP_A# Minimum Assertion Width.\0:0ms\1:4s\2:98ms\3:2s"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name = "PCH_RESET_CYCLE_DURATION"
	Value = "4"
	Help = "Reset Power Cycle Duration.\1:1-2s\2:2-3s\3:3-4s\4:4-5s\Supported in PCH RC v1.4.0."
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name = "SLP_STRCH_SUS_UP"
	Value = "0"
	Help = "SLP Stretching After SUS Well Power Up\0:Disable\1:Enable"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name = "TTLEVELS_SUGGEST"
	Value = "1"
	Help = "Thermal Throttling.\0:Disable\1:Enable"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name = "DMIHAAWC_SUGGEST"
	Value = "1"
	Help = "0:Disable\1:Enable"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name = "SATATT_SUGGEST"
	Value = "1"
	Help = "0:Disable\1:Enable"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name = "SIRQ_ENABLE"
	Value = "1"
	Help = "0:Disable\1:Enable"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name = "SIRQ_START_FRAME_PULSE"
	Value = "0"
	Help = "0:4 clocks\1:6 clocks\2:8 clocks"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name = "PCH_PCIE_ADVANCED_ERROR_REPORTING"
	Value = "0"
	Help = "0:Disable\1:Enable"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name = "PCH_PCIE_PME_INTERRUPT"
	Value = "0"
	Help = "0:Disable\1:Enable"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name = "PCH_PCIE_COMPLETION_TIME_OUT"
	Value = "0"
	Help = "0:Default\1:50us~100us\2:1ms~10ms\3:16ms~55ms\4:65ms~210ms\5:260ms~900ms\6:1s~3.5s\7:4s~13s\8:17s~64s\9:Disable"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name = "PCH_PCIE_TEMP_RP_BUS_NUM_MIN"
	Value = "2"
	Help = "Temp Root Port Bus Number Min"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name = "PCH_PCIE_TEMP_RP_BUS_NUM_MAX"
	Value = "4"
	Help = "Temp Root Port Bus Number Max"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name = "PCH_PCIE_TEMP_RP_BUS_NUM_MAX"
	Value = "$(TBT_PCH_PCIE_TEMP_RP_BUS_NUM_MAX)"
	Help = "Temp Root Port Bus Number Max"
	TokenType = Integer
	TargetH = Yes
	Token = "Thunderbolt_SUPPORT" "=" "1"
End

TOKEN
	Name = "MAX_EXTRA_BUS_RESERVED"
	Value = "7"
	Help = "The Max number of extra Bus Reserved for bridges behind this Root Bridge "
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name = "MAX_EXTRA_BUS_RESERVED"
	Value = "$(TBT_MAX_EXTRA_BUS_RESERVED)"
	Help = "The Max number of extra Bus Reserved for bridges behind this Root Bridge "
	TokenType = Integer
	TargetH = Yes
	Token = "Thunderbolt_SUPPORT" "=" "1"
End

TOKEN
	Name = "MAX_PCIE_MEM_RESERVED"
	Value = "20"
	Help = "The Max number of reserved memory range for this Root Bridge."
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name = "MAX_PCIE_MEM_RESERVED"
	Value = "$(TBT_MAX_PCIE_MEM_RESERVED)"
	Help = "The Max number of reserved memory range for this Root Bridge."
	TokenType = Integer
	TargetH = Yes
	Token = "Thunderbolt_SUPPORT" "=" "1"
End

TOKEN
	Name = "MAX_PCIE_PF_MEM_RESERVED"
	Value = "20"
	Help = "The Max number of prefetchable memory range for this Root Bridge."
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name = "MAX_PCIE_PF_MEM_RESERVED"
	Value = "$(TBT_MAX_PCIE_PF_MEM_RESERVED)"
	Help = "The Max number of prefetchable memory range for this Root Bridge."
	TokenType = Integer
	TargetH = Yes
	Token = "Thunderbolt_SUPPORT" "=" "1"
End

TOKEN
	Name = "MAX_PCIE_IO_RESERVED"
	Value = "20"
	Help = "The Max number of IO range for this Root Bridge."
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name = "MAX_PCIE_IO_RESERVED"
	Value = "$(TBT_MAX_PCIE_IO_RESERVED)"
	Help = "The Max number of IO range for this Root Bridge."
	TokenType = Integer
	TargetH = Yes
	TOKEN = "Thunderbolt_SUPPORT" "=" "1"
End

TOKEN
	Name = "SATA_MODE_IDE"
	Value = "0"
	TokenType = Integer
	TargetH = Yes
        Lock = Yes
End

TOKEN
	Name = "SATA_MODE_AHCI"
	Value = "1"
	TokenType = Integer
	TargetH = Yes
        Lock = Yes
End

TOKEN
	Name = "SATA_MODE_RAID"
	Value = "2"
	TokenType = Integer
	TargetH = Yes
        Lock = Yes
End

TOKEN
	Name  = "SATA_PORT1_LENGTH_CONFIG"
	Value  = "{1, 0, 1, 0, 1, 2}"
	Help  = "format: SATA_GEN1_RXEQ_ENABLE, SATA_GEN1_RXEQ_VALUE, SATA_GEN2_RXEQ_ENABLE, SATA_GEN2_RXEQ_VALUE, SATA_GEN3_RXEQ_ENABLE, SATA_GEN3_RXEQ_VALUE. Enable item: Enable:1\Disable:0. Value item:vaule range for ULT platform:0 ~ 0xF. \ vaule range for Two-chip platform:1 ~ 0xC. Please refer Intel PCH EDS for detail information."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "SATA_PORT2_LENGTH_CONFIG"
	Value  = "{1, 0, 1, 0, 1, 2}"
	Help  = "format: SATA_GEN1_RXEQ_ENABLE, SATA_GEN1_RXEQ_VALUE, SATA_GEN2_RXEQ_ENABLE, SATA_GEN2_RXEQ_VALUE, SATA_GEN3_RXEQ_ENABLE, SATA_GEN3_RXEQ_VALUE. Enable item: Enable:1\Disable:0. Value item:vaule range for ULT platform:0 ~ 0xF. \ vaule range for Two-chip platform:1 ~ 0xC. Please refer Intel PCH EDS for detail information."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "SATA_PORT3_LENGTH_CONFIG"
	Value  = "{1, 0, 1, 0, 1, 2}"
	Help  = "format: SATA_GEN1_RXEQ_ENABLE, SATA_GEN1_RXEQ_VALUE, SATA_GEN2_RXEQ_ENABLE, SATA_GEN2_RXEQ_VALUE, SATA_GEN3_RXEQ_ENABLE, SATA_GEN3_RXEQ_VALUE. Enable item: Enable:1\Disable:0. Value item:vaule range for ULT platform:0 ~ 0xF. \ vaule range for Two-chip platform:1 ~ 0xC. Please refer Intel PCH EDS for detail information."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "SATA_PORT4_LENGTH_CONFIG"
	Value  = "{1, 0, 1, 0, 1, 2}"
	Help  = "format: SATA_GEN1_RXEQ_ENABLE, SATA_GEN1_RXEQ_VALUE, SATA_GEN2_RXEQ_ENABLE, SATA_GEN2_RXEQ_VALUE, SATA_GEN3_RXEQ_ENABLE, SATA_GEN3_RXEQ_VALUE. Enable item: Enable:1\Disable:0. Value item:vaule range for ULT platform:0 ~ 0xF. \ vaule range for Two-chip platform:1 ~ 0xC. Please refer Intel PCH EDS for detail information."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "SATA_PORT5_LENGTH_CONFIG"
	Value  = "{1, 0, 1, 0, 1, 2}"
	Help  = "format: SATA_GEN1_RXEQ_ENABLE, SATA_GEN1_RXEQ_VALUE, SATA_GEN2_RXEQ_ENABLE, SATA_GEN2_RXEQ_VALUE, SATA_GEN3_RXEQ_ENABLE, SATA_GEN3_RXEQ_VALUE. Enable item: Enable:1\Disable:0. Value item:vaule range for ULT platform:0 ~ 0xF. \ vaule range for Two-chip platform:1 ~ 0xC. Please refer Intel PCH EDS for detail information."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "SATA_PORT6_LENGTH_CONFIG"
	Value  = "{1, 0, 1, 0, 1, 2}"
	Help  = "format: SATA_GEN1_RXEQ_ENABLE, SATA_GEN1_RXEQ_VALUE, SATA_GEN2_RXEQ_ENABLE, SATA_GEN2_RXEQ_VALUE, SATA_GEN3_RXEQ_ENABLE, SATA_GEN3_RXEQ_VALUE. Enable item: Enable:1\Disable:0. Value item:vaule range for ULT platform:0 ~ 0xF. \ vaule range for Two-chip platform:1 ~ 0xC. Please refer Intel PCH EDS for detail information"
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name = "SPI_FV_BB_PROTECTED_RANGE_BASE"
	Value = "$(FLASH_SIZE) - (0xFFFFFFFF - $(FV_BB_BASE) + 1)"
	Help = "it is BIOS rom address offset, C code will translate it to Flash rom address"
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "SPI_FV_BB_PROTECTED_RANGE_LENGTH"
	Value = "$(FV_BB_BLOCKS) * $(FLASH_BLOCK_SIZE)"
	Help = "Protected region length"
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "SPI_FV_MAIN_PROTECTED_RANGE_BASE"
	Value = "$(FLASH_SIZE) - (0xFFFFFFFF - $(FV_MAIN_BASE) + 1)"
	Help = "it is BIOS rom address offset, C code will translate it to Flash rom address"
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "SPI_FV_MAIN_PROTECTED_RANGE_LENGTH"
	Value = "$(FV_MAIN_BLOCKS) * $(FLASH_BLOCK_SIZE)"
	Help = "Protected region length"
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "SPI_FV_DATA_PROTECTED_RANGE_BASE"
	Value = "$(FLASH_SIZE) - (0xFFFFFFFF - $(FV_DATA_BASE) + 1)"
	Help = "it is BIOS rom address offset, C code will translate it to Flash rom address"
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "SPI_FV_DATA_PROTECTED_RANGE_LENGTH"
	Value = "$(FV_DATA_SIZE)"
	Help = "Protected range length"
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "SPI_PROTECTED_RANGE_0"
	Value = "{2, FALSE, FALSE, $(SPI_FV_BB_PROTECTED_RANGE_BASE), $(SPI_FV_BB_PROTECTED_RANGE_LENGTH)}"
	Help = "Format:\ 1st - The type of protected range 0, the available types are Undefined Type(0), Descriptor Type(1), BIOS Type(2), ME/TXE Type(3) abd GBE Type(4).\ 2nd - Write Protected Enable.\ 3rd - Read Protected Enable.\ 4th - The protection range base(MUST be 4KB alignment), it is only used for the protected types 0(Undefined) and 2(BIOS).\ 5th - The protection range length(the minimun length MUST be 4KB).\ Note : If 2nd & 3rd parameters both are Zeros, then this protected range will be disabled.\ This protected range is default for FV_BB, but you can update it according to your own design."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name = "SPI_PROTECTED_RANGE_1"
	Value = "{2, FALSE, FALSE, $(SPI_FV_MAIN_PROTECTED_RANGE_BASE), $(SPI_FV_MAIN_PROTECTED_RANGE_LENGTH)}"
	Help = "Format:\ 1st - The type of protected range 1, the available types are Undefined Type(0), Descriptor Type(1), BIOS Type(2), ME/TXE Type(3) abd GBE Type(4).\ 2nd - Write Protected Enable.\ 3rd - Read Protected Enable.\ 4th - The protection range base(MUST be 4KB alignment), it is only used for the protected types 0(Undefined) and 2(BIOS).\ 5th - The protection range length(the minimun length MUST be 4KB).\ Note : If 2nd & 3rd parameters both are Zeros, then this protected range will be disabled.\ This protected range is default for FV_MAIN, but you can update it according to your own design."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name = "SPI_PROTECTED_RANGE_2"
	Value = "{2, FALSE, FALSE, $(SPI_FV_DATA_PROTECTED_RANGE_BASE), $(SPI_FV_DATA_PROTECTED_RANGE_LENGTH)}"
	Help = "Format:\ 1st - The type of protected range 2, the available types are Undefined Type(0), Descriptor Type(1), BIOS Type(2), ME/TXE Type(3) abd GBE Type(4).\ 2nd - Write Protected Enable.\ 3rd - Read Protected Enable.\ 4th - The protection range base(MUST be 4KB alignment), it is only used for the protected types 0(Undefined) and 2(BIOS).\ 5th - The protection range length(the minimun length MUST be 4KB).\ Note : If 2nd & 3rd parameters both are Zeros, then this protected range will be disabled.\ This protected range is default for FV_DATA, but you can update it according to your own design."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name = "SPI_PROTECTED_RANGE_3"
	Value = "{0, FALSE, FALSE, 0, 0}"
	Help = "Format:\ 1st - The type of protected range 3, the available types are Undefined Type(0), Descriptor Type(1), BIOS Type(2), ME/TXE Type(3) abd GBE Type(4).\ 2nd - Write Protected Enable.\ 3rd - Read Protected Enable.\ 4th - The protection range base(MUST be 4KB alignment), it is only used for the protected types 0(Undefined) and 2(BIOS).\ 5th - The protection range length(the minimun length MUST be 4KB).\ Note : If 2nd & 3rd parameters both are Zeros, then this protected range will be disabled."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name = "SPI_PROTECTED_RANGE_4"
	Value = "{0, FALSE, FALSE, 0, 0}"
	Help = "Format:\ 1st - The type of protected range 4, the available types are Undefined Type(0), Descriptor Type(1), BIOS Type(2), ME/TXE Type(3) abd GBE Type(4).\ 2nd - Write Protected Enable.\ 3rd - Read Protected Enable.\ 4th - The protection range base(MUST be 4KB alignment), it is only used for the protected types 0(Undefined) and 2(BIOS).\ 5th - The protection range length(the minimun length MUST be 4KB).\ Note : If 2nd & 3rd parameters both are Zeros, then this protected range will be disabled."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "FORCE_USER_TO_SETUP_IF_CMOS_BAD"
	Value  = "0"
	Help  = "When this flag is on, Setup will be automatically launched whenever CMOS is bad."
	TokenType = Boolean
	TargetH = Yes
End
                                        # [EIP87695]>
TOKEN
	Name  = "SYSTEM_REBOOT_NORMALLY_IF_S3_IS_FAILED"
	Value  = "0"
	Help  = "Add a workaround path to avoid that the system can't reboot normally when S3 resume is failed."
	TokenType = Boolean
	TargetH = Yes
End
                                        # <[EIP87695]

TOKEN
	Name  = "ZPODD_SATA_PORT"
	Value  = "0x02"
	Help  = "ZPODD SATA Port Number."
	TokenType = Integer
	TargetH = Yes
  Token = "PCH_SKU" "=" "1"
End

TOKEN
	Name  = "SB_SATA_DLAE"
	Value  = "0"
	Help  = "Drive LED on ATAPI Enable (DLAE).\ 1:Enable \ 0:Disable"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "PCH_RCRB_OIC_CEN"
	Value  = "1"
	Help  = "Set RCBA Coprocessor Error Enable bit.\ 1:Enable \ 0:Disable"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "HOST_WLAN_PP_EN"
	Value  = "0"
	Help  = "Host Wireless LAN PHY Power.\ 1:Enable \ 0:Disable"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "ONLY_CLEAR_RTC_EN_IN_PEI"
	Value  = "1"
	Help  = "1: Only clear RTC_EN in PM1_EN \ 0: Clear all enable bits in PM1_EN."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = " "
	TokenType = Integer
End

TOKEN
	Name  = "=============== PCH CMOS Tokens =============="
	TokenType = Expression
End

TOKEN
	Name  = "SB_CMOS_MISC_FLAG_REG"
	Value  = "0x90"
	Help  = "[1:0] = 00b: COMPLETE_SAVE_RESTORE_STD_CMOS.\[1:0] = 01b: ENABLE_NMI_BEFORE_SMI_EXIT.\[1:0] = 10b: DISABLE_NMI_BEFORE_SMI_EXIT."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
        Lock = Yes
        Token = "CMOS_MANAGER_SUPPORT" "=" "1"
End

TOKEN
	Name  = " "
	TokenType = Integer
End

TOKEN
	Name = "============== IO DECODE SETINNG =============="
	Value = " "
	TokenType = Expression
End

TOKEN
	Name = "SB_IO_DECODE_IN_SEC"
	Value = "0"
	Help = "The value of SIO_PME_BASE_ADDRESS, '0' means no function."
	TokenType = Boolean
	TargetEQU = Yes
End

TOKEN
	Name = "SB_GEN_DECODE_RANGE_1"
	Value = "0"
#	   Value = "$(SIO_PME_BASE_ADDRESS)"  <example>
#	   Value = "$(IT8720F_PME_BASE_ADDRESS)"  <example>
	Help = "The value of SIO_PME_BASE_ADDRESS, '0' means no function."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Range = "00 - 0FFFFh"
	Token = "SB_IO_DECODE_IN_SEC" "=" "1"
End

TOKEN
	Name = "SB_GEN_DECODE_RANGE_2"
	Value = "0"
#	   Value = "$(SIO_PME_BASE_ADDRESS)"  <example>
#	   Value = "$(IT8720F_PME_BASE_ADDRESS)"  <example>
	Help = "The value of SIO_PME_BASE_ADDRESS, '0' means no function."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Range = "00 - 0FFFFh"
	Token = "SB_IO_DECODE_IN_SEC" "=" "1"
End

TOKEN
	Name = "SB_GEN_DECODE_RANGE_3"
	Value = "0"
#	   Value = "$(SIO_PME_BASE_ADDRESS)"  <example>
#	   Value = "$(IT8720F_PME_BASE_ADDRESS)"  <example>
	Help = "The value of SIO_PME_BASE_ADDRESS, '0' means no function."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Range = "00 - 0FFFFh"
	Token = "SB_IO_DECODE_IN_SEC" "=" "1"
End

TOKEN
	Name = "SB_GEN_DECODE_RANGE_4"
	Value = "0"
#	   Value = "$(SIO_PME_BASE_ADDRESS)"  <example>
#	   Value = "$(IT8720F_PME_BASE_ADDRESS)"  <example>
	Help = "The value of SIO_PME_BASE_ADDRESS, '0' means no function."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Range = "00 - 0FFFFh"
	Token = "SB_IO_DECODE_IN_SEC" "=" "1"
End

TOKEN
	Name  = " "
	TokenType = Integer
End

TOKEN
	Name = "============== GPIO SETINNG =============="
	Value = " "
	TokenType = Expression
End

TOKEN
	Name = "PROGRAM_DEFAULT_GPIO"
	Value = "1"
	TokenType = Boolean
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "PROGRAM_GPIO_TYPE"
	Value = "0"
	Help = "0:use array directly/1:use token define"
	TokenType = Boolean
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "IS_GPIO"
	Value = "0x0001"
	Help = "It is a GPIO, the pin will be used as a GPIO."
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "IS_NOT_GPIO"
	Value = "0x0000"
	Help = "It is not a GPIO, the pin will be used as native function."
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "IS_GPI"
	Value = "0x0002"
	Help = "It is a GPIO and is an input."
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "IS_GPO"
	Value = "0x0000"
	Help = "It is a GPIO and is an output."
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "OUTPUT_HIGH"
	Value = "0x0004"
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "OUTPUT_LOW"
	Value = "0x0000"
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "GPO_HIGH"
	Value = "$(IS_GPIO)+$(IS_GPO)+$(OUTPUT_HIGH)"
	Help = "It is a GP output and driving a high level on the pin."
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "GPO_LOW"
	Value = "$(IS_GPIO)+$(IS_GPO)+$(OUTPUT_LOW)"
	Help = "It is a GP output and driving a low level on the pin."
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "GPI_NON_INV"
	Value = "0x0000"
	Help = "The GPI pin will active high to cause SMI# or SCI. \This value must be combined with token IS_GPI."
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "GPI_INV"
	Value = "0x0008"
	Help = "The GPI pin will active low to cause SMI# or SCI. \This value must be combined with token IS_GPI."
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "GPO_BLINK"
	Value = "0x0010"
	Help = "The GPO pin will blink at a rate of approximately once per second. This value must be combined with tokens GPO_HIGH or GPO_LOW."
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name = "GPIO_RESET"
	Value = "0x0020"
	Help = ""
	TokenType = Integer
	TargetH = Yes
	Lock = Yes
End

TOKEN
  Name = "GPIO_OWN_ACPI"
  Value = "0x0000"
  Help = "It is GPIO use by ACPI driver."
  TokenType = Integer
  TargetH = Yes
  Lock = Yes
End

TOKEN
  Name = "GPIO_OWN_GPIO"
  Value = "0x0040"
  Help = "It is GPIO use by GPIO driver."
  TokenType = Integer
  TargetH = Yes
  Lock = Yes
End

TOKEN
  Name = "GPI_LEB_EDGE"
  Value = "0x0000"
  Help = "The GPI pin use by Edge Mode."
  TokenType = Integer
  TargetH = Yes
  Lock = Yes
End

TOKEN
  Name = "GPI_LEB_LEVEL"
  Value = "0x0080"
  Help = "The GPI pin use by Level Mode."
  TokenType = Integer
  TargetH = Yes
  Lock = Yes
End

TOKEN
  Name = "GPI_NDIS_ENABLE"
  Value = "0x0000"
  Help = "The GPI pin Input seneing enable."
  TokenType = Integer
  TargetH = Yes
  Lock = Yes
End

TOKEN
  Name = "GPI_NDIS_DISABLE"
  Value = "0x0100"
  Help = "The GPI pin Iutput seneing disable."
  TokenType = Integer
  TargetH = Yes
  Lock = Yes
End

TOKEN
  Name = "GPIO_GPIWP_NONE"
  Value = "0x0000"
  Help = "None"
  TokenType = Integer
  TargetH = Yes
  Lock = Yes
End

TOKEN
  Name = "GPIO_GPIWP_DOWN"
  Value = "0x0200"
  Help = "Pull Down"
  TokenType = Integer
  TargetH = Yes
  Lock = Yes
End

TOKEN
  Name = "GPIO_GPIWP_UP"
  Value = "0x0400"
  Help = "Pull Up"
  TokenType = Integer
  TargetH = Yes
  Lock = Yes
End

TOKEN
  Name = "GPIO_GPIWP_INVALID"
  Value = "0x0600"
  Help = "Invalid"
  TokenType = Integer
  TargetH = Yes
  Lock = Yes
End

TOKEN
  Name = "GPI_INT_ENABLE"
  Value = "0x0800"
  Help = "This bit enables the corresponding GPIOn to generate APIC interrupt."
  TokenType = Integer
  TargetH = Yes
  Lock = Yes
End

TOKEN
	Name = "GPIO_002"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "GPIO_003"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "GPIO_004"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "GPIO_005"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "GPIO_010"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "GPIO_019"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "GPIO_021"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "GPIO_022"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "GPIO_024"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "GPIO_029"
	Value = "$(GPO_HIGH)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "GPIO_035"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "GPIO_036"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "GPIO_037"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "GPIO_038"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "GPIO_039"
	Value = "$(IS_NOT_GPIO)"
	TokenType = Integer
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "GPIO_048"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "ULT_GPIO_000"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_001"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_002"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_003"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_004"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_005"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_006"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_007"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_008"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_INV)+$(GPI_LEB_LEVEL)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_009"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_LEB_LEVEL)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_010"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_INV)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_011"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPI_LEB_LEVEL)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_012"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_013"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_014"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_INV)+$(GPIO_GPIWP_DOWN)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_015"
	Value  = "$(IS_GPIO)+$(OUTPUT_LOW)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_016"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_017"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_INV)+$(GPI_LEB_LEVEL)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_018"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPI_LEB_LEVEL)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_019"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_020"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_021"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_022"
	Value  = "$(IS_GPIO)+$(OUTPUT_LOW)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_023"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_024"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPIO_OWN_GPIO)+$(GPIO_RESET)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_025"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_026"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_027"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_INV)+$(GPI_LEB_LEVEL)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_028"
	Value  = "$(IS_GPIO)+$(OUTPUT_LOW)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_029"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_030"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_031"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_032"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_033"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_034"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_INV)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_035"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_INV)+$(OUTPUT_HIGH)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_036"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_INV)+$(GPI_LEB_LEVEL)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_037"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_038"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_039"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_040"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_041"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_042"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_043"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_044"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_045"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_INV)+$(GPI_LEB_LEVEL)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_046"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_047"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_INV)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_048"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_049"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_050"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_LEB_LEVEL)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_051"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_INV)+$(GPI_LEB_LEVEL)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_052"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_053"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_054"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_INV)+$(GPI_LEB_LEVEL)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_055"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_LEB_LEVEL)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_056"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_057"
	Value  = "$(IS_GPIO)+$(OUTPUT_LOW)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_058"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_LEB_LEVEL)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_059"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_060"
	Value  = "$(IS_GPIO)+$(OUTPUT_LOW)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_061"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_062"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_063"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_064"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_065"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_066"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_067"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_068"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_069"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_070"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_071"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_072"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_073"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_074"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_075"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_076"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_077"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_078"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_LEB_LEVEL)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_079"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_INV)+$(GPI_LEB_LEVEL)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_080"
	Value  = "$(IS_GPIO)+$(IS_GPI)+$(GPI_LEB_LEVEL)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_081"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_082"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_083"
	Value  = "$(IS_GPIO)+$(OUTPUT_LOW)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_084"
	Value  = "$(IS_GPIO)+$(OUTPUT_LOW)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_085"
	Value  = "$(IS_GPIO)+$(OUTPUT_LOW)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_086"
	Value  = "$(IS_GPIO)+$(OUTPUT_LOW)+$(GPI_LEB_LEVEL)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_087"
	Value  = "$(IS_GPIO)+$(OUTPUT_LOW)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_088"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_089"
	Value  = "$(IS_GPIO)+$(OUTPUT_HIGH)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_090"
	Value  = "$(IS_GPIO)+$(OUTPUT_LOW)+$(GPI_NDIS_DISABLE)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_091"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_092"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_093"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_094"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "ULT_GPIO_095"
	Value  = "$(IS_NOT_GPIO)+$(OUTPUT_HIGH)+$(GPIO_OWN_GPIO)"
	Help  = "BIT0:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\BIT1:GPIO Input/Output Select.\BIT2:GPIO Level Select.\BIT3:GPIO Signal Invert(Only For GPIO_00~31).\BIT4:GPIO Blink Enable(Only For GPIO_00~31).\BIT5:GPIO Reset Select.\BIT6:GPIO OWN - 0:ACPI driver/ 1:GPIO driver \ BIT7:GPIO LEB - 0: Edge Mode/ 1: Level Mode \BIT8: GPIO DIS - 0: Input sensing enable/ 1: Output sensing disable \BIT9~10 - 00: none/ 01:pull down/ 10: pull up/ 11: invalid \ BIT11 - 0: GPI Interrupt Disable / 1: GPI Interrupt Enable"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "PROGRAM_GPIO_TYPE" "=" "1"
End

TOKEN
	Name  = "=============== ACPI Specific Tokens =============="
	TokenType = Expression
End

TOKEN
	Name  = "APCB"
	Value  = "0x0FEC00000"
	Help  = "Default I/O APIC(s) memory start address, bytes\0x0FEC00000 - default, 0 - I/O APIC's disabled"
	TokenType = Integer
	TargetASL = Yes
	TargetH = Yes
End

TOKEN
	Name  = "APCL"
	Value  = "0x1000"
	Help  = "I/O APIC(s) memory decoded range, bytes\0x1000 - default,\0 - I/O APIC's not decoded "
	TokenType = Integer
	TargetASL = Yes
	TargetH = Yes
End

TOKEN
	Name  = "A_POS_DECODE"
	Value  = "0"
	TokenType = Boolean
	TargetMAK = Yes
End

TOKEN
	Name  = "SW_SMI_SB_ACPI_S3"
	Value  = "0xb8"
	Help  = "Value to be written into SMI command register \to enable S3 patched codes"
	TokenType = Integer
	TargetH = Yes
	Range  = "0xB7 - 0xBD"
End

TOKEN
	Name  = "SMCR"
	Value  = "$(PM_BASE_ADDRESS)+0x30"
	Help  = "SMI Control Register"
	TokenType = Integer
	TargetASL = Yes
End

TOKEN
	Name  = "ACPI_SCI_INT"
	Value  = "9"
	Help  = "SCI Interrupt number"
	TokenType = Integer
	TargetH = Yes
	Range  = "4-15"
End

TOKEN
	Name  = "PM_SCI_ENABLE"
	Value  = "0x01"
	Help  = "Value that needs to be written in PM1_CNT regirter \to Enable SCI generation on PM events"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name  = "ACPI_ALARM_DAY_CMOS"
	Value  = "0x0d"
	Help  = "RTC Index of the Day-of-Month alarm"
	TokenType = Integer
	TargetH = Yes
	Range  = "0 - 0xff 0 = not supported"
End

TOKEN
	Name  = "ACPI_ALARM_MONTH_CMOS"
	Value  = "0x00"
	Help  = "RTC Index of the Month-of-year alarm\"
	TokenType = Integer
	TargetH = Yes
	Range  = "0-0xff 0 = not supported"
End

TOKEN
	Name  = "ACPI_CENTURY_CMOS"
	Value  = "0x32"
	Help  = "RTC Index of the Century-of-Data\"
	TokenType = Integer
	TargetH = Yes
	Range  = "0-0xff 0 = not supported"
End

TOKEN
	Name  = "ACPI_RESET_REG_ADDRESS"
	Value  = "0xcf9"
	Help  = "Reset Register Address (Part of GAS Structure refer, to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0 = not Supported other values depends on other GAS elements"
End

TOKEN
	Name  = "ACPI_RESET_REG_TYPE"
	Value  = "1"
	Help  = "Reset Register Id (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0=System memory; 1=System I/O; 2=PCI Config Space; 3=Embeded Controller; 4=SMBus; 0x7F=Functional Fixed Hardware; All other values reserved"
End

TOKEN
	Name  = "ACPI_RESET_REG_BITWIDTH"
	Value  = "8"
	Help  = "Reset Register Bit Width (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "ACPI_RESET_REG_BITOFFSET"
	Value  = "0"
	Help  = "Reset Register Bit Offset (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "ACPI_RESET_REG_VALUE"
	Value  = "006h"
	Help  = "Value to write to the Reset Register to initiate System Reset"
	TokenType = Integer
	TargetH = Yes
	Range  = "? - chipset specific"
End

TOKEN
	Name  = "PM1A_EVT_BLK_ADDRESS"
	Value  = "$(PM_BASE_ADDRESS)"
	Help  = "PM1a_EVT BLK Base Address (Part of GAS Structure refer, to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0 = not Supported other values depends on other GAS elements"
End

TOKEN
	Name  = "PM1A_EVT_BLK_TYPE"
	Value  = "1"
	Help  = "PM1a_EVT BLK Registes Id (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0=System memory; 1=System I/O; 2=PCI Config Space; 3=Embeded Controller; 4=SMBus; 0x7F=Functional Fixed Hardware; All other values reserved"
End

TOKEN
	Name  = "PM1A_EVT_BLK_BITWIDTH"
	Value  = "32"
	Help  = "PM1a_EVT BLK Registes Bit Width (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "PM1A_EVT_BLK_BITOFFSET"
	Value  = "0"
	Help  = "PM1a_EVT BLK Registes Bit Offset (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "PM1_EVT_LENGTH"
	Value  = "4"
	Help  = "PM1a_EVT BLK length in bytes"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "PM1A_CNT_BLK_ADDRESS"
	Value  = "$(PM_BASE_ADDRESS)+0x04"
	Help  = "PM1a_CNT BLK Base Address (Part of GAS Structure refer, to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0 = not Supported other values depends on other GAS elements"
End

TOKEN
	Name  = "PM1A_CNT_BLK_TYPE"
	Value  = "1"
	Help  = "PM1a_CNT BLK Registes Id (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0=System memory; 1=System I/O; 2=PCI Config Space; 3=Embeded Controller; 4=SMBus; 0x7F=Functional Fixed Hardware; All other values reserved"
End

TOKEN
	Name  = "PM1A_CNT_BLK_BITWIDTH"
	Value  = "16"
	Help  = "PM1a_CNT BLK Registes Bit Width (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "PM1A_CNT_BLK_BITOFFSET"
	Value  = "0"
	Help  = "PM1a_CNTT BLK Registes Bit Offset (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "PM1_CNT_LENGTH"
	Value  = "2"
	Help  = "PM1a_CNT BLK length in bytes"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "PM1B_EVT_BLK_ADDRESS"
	Value  = "0"
	Help  = "PM1b_EVT BLK Base Address (Part of GAS Structure refer, to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0 = not Supported other values depends on other GAS elements"
End

TOKEN
	Name  = "PM1B_EVT_BLK_TYPE"
	Value  = "1"
	Help  = "PM1b_EVT BLK Registes Id (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0=System memory; 1=System I/O; 2=PCI Config Space; 3=Embeded Controller; 4=SMBus; 0x7F=Functional Fixed Hardware; All other values reserved"
End

TOKEN
	Name  = "PM1B_EVT_BLK_BITWIDTH"
	Value  = "0"
	Help  = "PM1a_EVT BLK Registes Bit Width (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "PM1B_EVT_BLK_BITOFFSET"
	Value  = "0"
	Help  = "PM1a_EVT BLK Registes Bit Offset (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "PM1B_CNT_BLK_ADDRESS"
	Value  = "0"
	Help  = "PM1b_CNT BLK Base Address (Part of GAS Structure refer, to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0 = not Supported other values depends on other GAS elements"
End

TOKEN
	Name  = "PM1B_CNT_BLK_TYPE"
	Value  = "1"
	Help  = "PM1a_CNT BLK Registes Id (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0=System memory; 1=System I/O; 2=PCI Config Space; 3=Embeded Controller; 4=SMBus; 0x7F=Functional Fixed Hardware; All other values reserved"
End

TOKEN
	Name  = "PM1B_CNT_BLK_BITWIDTH"
	Value  = "0"
	Help  = "PM1a_CNT BLK Registes Bit Width (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "PM1B_CNT_BLK_BITOFFSET"
	Value  = "0"
	Help  = "PM1a_CNTT BLK Registes Bit Offset (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "PM2_CNT_BLK_ADDRESS"
	Value  = "$(PM_BASE_ADDRESS)+0x50"
	Help  = "PM2_CNT BLK Base Address (Part of GAS Structure refer, to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0 = not Supported other values depends on other GAS elements"
End

TOKEN
	Name  = "PM2_CNT_BLK_TYPE"
	Value  = "1"
	Help  = "PM2_CNT BLK Registes Id (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0=System memory; 1=System I/O; 2=PCI Config Space; 3=Embeded Controller; 4=SMBus; 0x7F=Functional Fixed Hardware; All other values reserved"
End

TOKEN
	Name  = "PM2_CNT_BLK_BITWIDTH"
	Value  = "8"
	Help  = "PM2_CNT BLK Registes Bit Width (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "PM2_CNT_BLK_BITOFFSET"
	Value  = "0"
	Help  = "PM2_CNT BLK Registes Bit Offset (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "PM2_CNT_LENGTH"
	Value  = "1"
	Help  = "PM2_CNT BLK length in bytes"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "PM_TMR_BLK_ADDRESS"
	Value  = "$(PM_BASE_ADDRESS)+0x08"
	Help  = "PM_TMR BLK Base Address (Part of GAS Structure refer, to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0 = not Supported other values depends on other GAS elements"
End

TOKEN
	Name  = "PM_TMR_BLK_TYPE"
	Value  = "1"
	Help  = "PM_TMR BLK Registes Id (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0=System memory; 1=System I/O; 2=PCI Config Space; 3=Embeded Controller; 4=SMBus; 0x7F=Functional Fixed Hardware; All other values reserved"
End

TOKEN
	Name  = "PM_TMR_BLK_BITWIDTH"
	Value  = "32"
	Help  = "PM_TMR BLK Registes Bit Width (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "PM_TMR_BLK_BITOFFSET"
	Value  = "0"
	Help  = "PM_TMR BLK Registes Bit Offset (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "PM_TMR_LENGTH"
	Value  = "4"
	Help  = "PM_TMR BLK length in bytes"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "GPE0_BLK_ADDRESS"
	Value  = "$(PM_BASE_ADDRESS)+0x20"
	Help  = "GPE0 BLK Base Address (Part of GAS Structure refer, to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0 = not Supported other values depends on other GAS elements"
End

TOKEN
	Name  = "GPE0_BLK_ADDRESS"
	Value  = "$(PM_BASE_ADDRESS)+0x80"
	Help  = "GPE0 BLK Base Address (Part of GAS Structure refer, to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Token = "ULT_SUPPORT" "=" "1"
	Range  = "0 = not Supported other values depends on other GAS elements"
End

TOKEN
	Name  = "GPE0_BLK_TYPE"
	Value  = "1"
	Help  = "GPE0 BLK Registes Id (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0=System memory; 1=System I/O; 2=PCI Config Space; 3=Embeded Controller; 4=SMBus; 0x7F=Functional Fixed Hardware; All other values reserved"
End

TOKEN
	Name  = "GPE0_BLK_BITWIDTH"
	Value  = "128"
	Help  = "GPE0 BLK Registes Bit Width (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "GPE0_BLK_BITOFFSET"
	Value  = "0"
	Help  = "GPE0 BLK Registes Bit Offset (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "GPE0_BLK_LENGTH"
	Value  = "16"
	Help  = "GPE0 BLK length in bytes"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "GPE0_BLK_LENGTH"
	Value  = "32"
	Help  = "GPE0 BLK length in bytes"
	TokenType = Integer
	TargetH = Yes
	Token = "ULT_SUPPORT" "=" "1"
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "GPE1_BLK_ADDRESS"
	Value  = "0"
	Help  = "GPE1 BLK Base Address (Part of GAS Structure refer, to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0 = not Supported other values depends on other GAS elements"
End

TOKEN
	Name  = "GPE1_BLK_TYPE"
	Value  = "1"
	Help  = "GPE1 BLK Registes Id (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0=System memory; 1=System I/O; 2=PCI Config Space; 3=Embeded Controller; 4=SMBus; 0x7F=Functional Fixed Hardware; All other values reserved"
End

TOKEN
	Name  = "GPE1_BLK_BITWIDTH"
	Value  = "0"
	Help  = "GPE1 BLK Registes Bit Width (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "GPE1_BLK_BITOFFSET"
	Value  = "0"
	Help  = "GPE1 BLK Registes Bit Offset (Part of GAS Structure, refer to ACPI v2.0 spec for details)"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "GPE1_BLK_LENGTH"
	Value  = "0"
	Help  = "GPE1 BLK length in bytes"
	TokenType = Integer
	TargetH = Yes
	Range  = "value range depends on other GAS elements"
End

TOKEN
	Name  = "GPE1_BASE_OFFSET"
	Value  = "0"
	Help  = "GPE1 Base offset within the ACPI general purpose event model (FADT byte 94)"
	TokenType = Integer
	TargetH = Yes
	Range  = "0-0xff"
End

TOKEN
	Name  = "GPE1_BASE_OFFSET"
	Value  = "0x10"
	Help  = "GPE1 Base offset within the ACPI general purpose event model (FADT byte 94)"
	TokenType = Integer
	TargetH = Yes
	Token = "ULT_SUPPORT" "=" "1"
	Range  = "0-0xff"
End

TOKEN
	Name  = "PRIMARY_CHANNEL_ENABLE"
	Value  = "1"
	Help  = "Enable/Disable Primary Channel"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "PRIMARY_MASTER_DRIVE_ENABLE"
	Value  = "1"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "MAX_UDMA"
	Value  = "5"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name  = "MAX_PIO"
	Value  = "4"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name  = "PRIMARY_SLAVE_DRIVE_ENABLE"
	Value  = "1"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "SECONDARY_CHANNEL_ENABLE"
	Value  = "1"
	Help  = "Enable/Disable Secondary Channel"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "SECONDARY_MASTER_DRIVE_ENABLE"
	Value  = "1"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "SECONDARY_SLAVE_DRIVE_ENABLE"
	Value  = "1"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "BUSMASTER_ENABLE"
	Value  = "1"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "MASTER_INTERRUPT_BASE"
	Value  = "0x58"
	Help  = "This value set the Interrupt Vector base for the master. Hardware IRQ0 = this base.\In legacy real mode this value is 8. It can not be 8 in protected mode.\This value must be a multiple of 8, and the this value must be different than SLAVE_INTERRUPT_BASE."
	TokenType = Integer
	TargetH = Yes
	Range  = "0-F8"
End

TOKEN
	Name  = "SLAVE_INTERRUPT_BASE"
	Value  = "0x70"
	Help  = "This value set the Interrupt Vector base for the slave. Hardware IRQ8 = this base.\In legacy real mode this value is 0x70.\This value must be a multiple of 8, and the this value must be different than MASTER_INTERRUPT_BASE."
	TokenType = Integer
	TargetH = Yes
	Range  = "0-F8"
End

TOKEN
	Name  = "A_S0_PKG"
	Value  = "0x0,0x0,0,0"
	Help  = "Intel ICH(x) example. Modify for a new Chipset"
	TokenType = Expression
	TargetMAK = Yes
	Range  = "4 decimal or Hex (use '0x' prefix) values sepparated with ','"
End

TOKEN
	Name  = "A_S1_PKG"
	Value  = "0x1,0x0,0,0"
	Help  = "Intel ICH(x) example. Modify for a new Chipset"
	TokenType = Expression
	TargetMAK = Yes
	Range  = "4 decimal or Hex (use '0x' prefix) values separated with ','"
End

TOKEN
	Name  = "A_S2_PKG"
	Value  = "0x2,0x0,0,0"
	TokenType = Expression
	TargetMAK = Yes
	Range  = "4 decimal or Hex (use '0x' prefix) values separated with ','"
End

TOKEN
	Name  = "A_S3_PKG"
	Value  = "0x5,0x0,0,0"
	Help  = "Intel ICH(x) example. Modify for a new Chipset"
	TokenType = Expression
	TargetMAK = Yes
	Range  = "4 decimal or Hex (use '0x' prefix) values separated with ','"
End

TOKEN
	Name  = "A_S4_PKG"
	Value  = "0x6,0x0,0,0"
	Help  = "Intel ICH(x) example. Modify for a new Chipset"
	TokenType = Expression
	TargetMAK = Yes
	Range  = "4 decimal or Hex (use '0x' prefix) values separated with ','"
End

TOKEN
	Name  = "A_S5_PKG"
	Value  = "0x7,0x0,0,0"
	Help  = "Intel ICH(x) example. Modify for a new Chipset"
	TokenType = Expression
	TargetMAK = Yes
	Range  = "4 decimal or Hex (use '0x' prefix) values separated with ','"
End

TOKEN
	Name  = "S4_WAKE_FROM_RTC_SUPPORTED"
	Value  = "1"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name  = "REMOTE_POWER_ON_SUPPORTED"
	Value  = "0"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name  = "INCLUDE_SB_ASM_FILE_IN_SEC"
	Value  = "1"
	Help  = "Includes an ASM file and an eLink in SEC build process for SB code modification:"
	TokenType = Boolean
End

TOKEN
	Name  = "SLEEP_BUTTON_SUPPORT"
	Value  = "0"
	Help  = "Enable/Disable ACPI Sleep Button."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "HPET_SUPPORT"
	Value  = "1"
	Help  = "Enables High Performance Event Timer (HPET) Support in Project"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "HPET_BASE_ADDRESS"
	Value  = "0xFED00000"
	Help  = "HPET Block Registers"
	TokenType = Integer
	TargetH = Yes
	Range  = "0xFED00000 or 0xFED01000 or 0xFED02000 or 0xFED04000"
	Token = "HPET_SUPPORT" "=" "1"
End

TOKEN
	Name  = "HPTB"
	Value  = "$(HPET_BASE_ADDRESS)"
	Help  = "Same as HPET_BASE_ADDRESS for ASL use "
	TokenType = Integer
	TargetASL = Yes
	TargetH = Yes
	Token = "HPET_SUPPORT" "=" "1"
End

TOKEN
	Name  = "HPTC"
	Value  = "$(SB_RCRB_BASE_ADDRESS)+0x3404"
	Help  = "High Precision Event Timer Configuration Register"
	TokenType = Integer
	TargetASL = Yes
	Range  = "offset 0x3404 from RCBA "
	Token = "HPET_SUPPORT" "=" "1"
End

TOKEN
	Name  = "HPET_PROTOCOL_SUPPORT"
	Value  = "0"
	Help  = "Use High Performance Event Timer (HPET) instead of 8254 to support Timer protocol in Project"
	TokenType = Boolean
	TargetH = Yes
	Token = "HPET_SUPPORT" "=" "1"
End

TOKEN
	Name  = "HPET_DEFAULT_TICK_DURATION"
	Value  = "10000"
	Help  = "The unit is 100ns, the default value is 1ms."
	TokenType = Integer
	TargetH = Yes
	Token = "HPET_SUPPORT" "=" "1"
	Token = "HPET_PROTOCOL_SUPPORT" "=" "1"
End

TOKEN
	Name  = "HPET_OFFSET"
	Value  = "0"
	Help  = "The offset of High Performance Event Timer.\This value can't exceed in the number of HPET capability.\The timer must also be able to support periodic mode."
	TokenType = Integer
	TargetH = Yes
	Token = "HPET_SUPPORT" "=" "1"
	Token = "HPET_PROTOCOL_SUPPORT" "=" "1"
End

TOKEN
	Name  = "HPET_APIC_INTERRUPT_MODE"
	Value  = "1"
	Help  = "Off : The timer interrupt will be routed to PIC(8259).\On : The timer interrupt will be routed to APIC."
	TokenType = Boolean
	TargetH = Yes
	Token = "HPET_SUPPORT" "=" "1"
	Token = "HPET_PROTOCOL_SUPPORT" "=" "1"
End

TOKEN
	Name  = "HPET_APIC_INTERRUPT_PIN"
	Value  = "20"
	Help  = "Select an APIC interrupt pin for the timer's interrupt.\Notice! Please refer to your HPET F/W porting guide to know which APIC interrupt pins can be used for this timer's interrupt."
	TokenType = Integer
	TargetH = Yes
	Token = "HPET_SUPPORT" "=" "1"
        Token = "HPET_PROTOCOL_SUPPORT" "=" "1"
        Token = "HPET_APIC_INTERRUPT_MODE" "=" "1"
        Range  = "20, 21, 22, 23"
End

TOKEN
        Name  = "HPET_INTERRUPT_POLARITY"
        Value  = "0"
        Help  = "On : The polarity is high.\Off : The polarity is low."
        TokenType = Boolean
        TargetH = Yes
        Token = "HPET_SUPPORT" "=" "1"
        Token = "HPET_PROTOCOL_SUPPORT" "=" "1"
        Token = "HPET_APIC_INTERRUPT_MODE" "=" "1"
End

TOKEN
        Name  = "HPET_INTERRUPT_TRIGGER"
        Value  = "0"
        Help  = "On : level triggered.\Off : edge triggered."
        TokenType = Boolean
        TargetH = Yes
        Token = "HPET_SUPPORT" "=" "1"
        Token = "HPET_PROTOCOL_SUPPORT" "=" "1"
        Token = "HPET_APIC_INTERRUPT_MODE" "=" "1"
End

TOKEN
	Name  = "HDD_POWER_LOSS_IN_S3"
	Value  = "1"
	Help  = "Disable this feature if HDD doesn't lose power \during S3 resume. HDD need to be unlocked during \S3 resume if it loses power and \also HDD need to be put in Freeze state.\"
	TokenType = Boolean
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "CMOS_ADDR_PORT"
	Value  = "0x70"
	Help  = "CMOS Index Port."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "CMOS_DATA_PORT"
	Value  = "0x71"
	Help  = "CMOS Data Port."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "CMOS_BAD_REG"
	Value  = "0x0E"
	Help  = "CMOS Diagnostics Port."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "DEFAULT_YEAR"
	Value  = "2009"
	Help  = "Year, that will be set in RTC in case of date corruption"
	TokenType = Integer
	TargetH = Yes
	Range  = "1998-2099"
End

TOKEN
	Name  = "DEFAULT_MONTH"
	Value  = "1"
	Help  = "Month, that will be set in RTC in case of date corruption"
	TokenType = Integer
	TargetH = Yes
	Range  = "1-12"
End

TOKEN
	Name  = "DEFAULT_DAY"
	Value  = "1"
	Help  = "Day, that will be set in RTC in case of date corruption"
	TokenType = Integer
	TargetH = Yes
	Range  = "1-31"
End

TOKEN
	Name  = "EARLIEST_YEAR"
	Value  = "1998"
	Help  = "If year, stored in RTC is less than this value, date will be considered as incorrect"
	TokenType = Integer
	TargetH = Yes
	Range  = "1998"
End

TOKEN
	Name  = "PCI_DEBUG_PORT"
	Value  = "080h"
	Help  = "Debug Card I/O Port, default is 80h"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name  = "SB_TEMP_IO_BASE"
	Value  = "0x1200"
	Help  = "A Temporal I/O Base Address for Init.\Its length is 1K bytes."
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name  = "AMI_INIT_VERB_TABLE_IN_S3"
	Value  = "0"
	Help  = "This is a backup solution for Intel RC"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name = "RESERVED_ROM_LENGTH"
	Value = "0x1000000"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "RESERVED_ROM_BASE"
	Value = "(0xFFFFFFFF-$(RESERVED_ROM_LENGTH)+1)"
	Help  = "Reserved for ROM image."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "SB_TEMP_MMIO_BASE"
	Value = "($(RESERVED_ROM_BASE)-$(SB_TEMP_MMIO_BASE_LENGTH))"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name = "SB_TEMP_MMIO_BASE_LENGTH"
	Value = "0x10000"
	Help  = "Intel required minimum size is 64KB bytes."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Lock = Yes
End

TOKEN
	Name  = "MAX_NUM_HD_CODECS"
	Value  = "0x04"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name  = "KBC_AUTODETECT_PORTS"
	Value  = "0"
	Help  = "Auto detection of KB/MS using AMI KB-5.  This switch will enable/disable the connector swap of Keyboard and PS2 Mouse i.e. keyboard\can be connected to PS2 Mouse connector and vice-versa."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "SIO_SB_DEV_NUM"
	Value  = "0x1F"
	Help  = "SB LPC Device Number"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name  = "FLSZ"
	Value  = "$(FLASH_SIZE)"
	Help  = "Size of the Flash Device in bytes"
	TokenType = Integer
	TargetASL = Yes
End

TOKEN
	Name  = "SB_RCRB_BASE_ADDRESS"
	Value  = "0FED1C000h"
	Help  = "\The Root Complex Base Address of PCH.\Must be aligned a 16-KB boundary."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "SB_RCBA"
	Value  = "$(SB_RCRB_BASE_ADDRESS)"
	Help  = "\The Root Complex Base Address of PCH.\Must be aligned a 16-KB boundary."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "SB_RCRB_LENGTH"
	Value  = "0x4000"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name  = "SRCB"
	Value  = "$(SB_RCRB_BASE_ADDRESS)"
	TokenType = Integer
	TargetASL = Yes
End

TOKEN
	Name  = "RCLN"
	Value  = "$(SB_RCRB_LENGTH)"
	TokenType = Integer
	TargetASL = Yes
End

TOKEN
	Name  = "RESERVED_PAGE_ROUTE"
	Value  = "0"
	Help  = "0 - Forward to LPC.\1 - Forward to PCI.\Please refer to RCBA#3410h[2]."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "RC_PORT_0"
	Value  = "1"
	Help  = "Set to 'On' if PCH Root Complex Port #0  phisically enabled and connected on the board"
	TokenType = Boolean
	TargetH = Yes
	Range  = "On - Off"
End

TOKEN
	Name  = "RC_PORT_1"
	Value  = "1"
	Help  = "Set to 'On' if PCH Root Complex Port #1  phisically enabled and connected on the board"
	TokenType = Boolean
	TargetH = Yes
	Range  = "On - Off"
	Token = "RC_PORT_0" "=" "1"
End

TOKEN
	Name  = "RC_PORT_2"
	Value  = "1"
	Help  = "Set to 'On' if PCH Root Complex Port #2  phisically enabled and connected on the board"
	TokenType = Boolean
	TargetH = Yes
	Range  = "On - Off"
	Token = "RC_PORT_0" "=" "1"
End

TOKEN
	Name  = "RC_PORT_3"
	Value  = "1"
	Help  = "Set to 'On' if PCH Root Complex Port #3  phisically enabled and connected on the board"
	TokenType = Boolean
	TargetH = Yes
	Range  = "On - Off"
	Token = "RC_PORT_0" "=" "1"
End

TOKEN
	Name  = "RC_PORT_4"
	Value  = "1"
	Help  = "Set to 'On' if PCH Root Complex Port #4  phisically enabled and connected on the board"
	TokenType = Boolean
	TargetH = Yes
	Range  = "On - Off"
	Token = "RC_PORT_0" "=" "1"
End

TOKEN
	Name  = "RC_PORT_5"
	Value  = "1"
	Help  = "Set to 'On' if PCH Root Complex Port #5  phisically enabled and connected on the board"
	TokenType = Boolean
	TargetH = Yes
	Range  = "On - Off"
	Token = "RC_PORT_0" "=" "1"
End

TOKEN
	Name  = "RC_PORT_6"
	Value  = "1"
	Help  = "Set to 'On' if PCH Root Complex Port #6  phisically enabled and connected on the board"
	TokenType = Boolean
	TargetH = Yes
	Range  = "On - Off"
	Token = "RC_PORT_0" "=" "1"
End

TOKEN
	Name  = "RC_PORT_7"
	Value  = "1"
	Help  = "Set to 'On' if PCH Root Complex Port #7  phisically enabled and connected on the board"
	TokenType = Boolean
	TargetH = Yes
	Range  = "On - Off"
	Token = "RC_PORT_0" "=" "1"
End

TOKEN
	Name  = "HOTPLUG_RMV_SUPPORT"
	Value  = "0"
	Help  = "Main switch if PCH Root Complex Port support _RMV function which is defined in ASL code. 0:Disable\1:Enable"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
	Token = "HOTPLUG_SUPPORT" "=" "1"
End

ELINK
	Name  = "/D HOTPLUG_EOI_FLAG"
	Parent  = "GLOBAL_DEFINES"
	InvokeOrder = AfterParent
	Token = "HOTPLUG_RMV_SUPPORT" "=" "0"
End

TOKEN
	Name  = "SX_NOTIFY_PWRB"
	Value  = "1"
	Help  = "Enable/Disable report notify power button event when system resume form sleep state."
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
End

TOKEN
	Name  = "PCIE_CLEAR_RETRAIN_BIT_SUPPORT"
	Value  = "0"
	Help  = "Main switch to clear PCH Root Port retrain bit for some device will not clear this bit. It will make 1 ms delay for each PCIE device 0:Disable\1:Enable"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
End

ELINK
	Name  = "/D PCIE_CLEAR_RETRAIN_BIT_SUPPORT_FLAG"
	Parent  = "GLOBAL_DEFINES"
	InvokeOrder = AfterParent
	Token = "PCIE_CLEAR_RETRAIN_BIT_SUPPORT" "=" "1"
End

TOKEN
	Name  = " "
	TokenType = Integer
End

TOKEN
	Name  = "====== SB USB Rx Configuration ======"
	TokenType = Expression
End

TOKEN
	Name  = "PCI_EHCI_BUS_NUMBER"
	Value  = "0x0"
	Help  = "EHCI controller bus number"
	TokenType = Integer
	TargetH = Yes
	Token = "USB_DEBUG_TRANSPORT" "=" "1"
End

TOKEN
	Name  = "PCI_EHCI_DEV_FUNC_NUMBER"
	Value  = "0xD0"
	Help  = "EHCI controller device and function number. \Bit 0-2 represents function number and\ Bit 3-7 represents device number"
	TokenType = Integer
	TargetH = Yes
	Token = "USB_DEBUG_TRANSPORT" "=" "1"
End

TOKEN
	Name  = "PCI_EHCI_BAR_OFFSET"
	Value  = "0x10"
	TokenType = Integer
	TargetH = Yes
	Token = "USB_DEBUG_TRANSPORT" "=" "1"
End

TOKEN
	Name  = "EHCI_MMIO_BASE_ADDRESS"
	Value  = "$(EHCI_MMIO_BASE_ADDRESS1)"
	TokenType = Integer
	TargetH = Yes
	Token = "PCI_EHCI_DEV_FUNC_NUMBER" "=" "0xD0"
	Token = "USB_DEBUG_TRANSPORT" "=" "1"
End

TOKEN
	Name  = "EHCI_MMIO_BASE_ADDRESS"
	Value  = "$(EHCI_MMIO_BASE_ADDRESS2)"
	TokenType = Integer
	TargetH = Yes
	Token = "PCI_EHCI_DEV_FUNC_NUMBER" "=" "0xE8"
	Token = "USB_DEBUG_TRANSPORT" "=" "1"
End

TOKEN
	Name  = "EHCI_MMIO_BASE_ADDRESS1"
	Value  = "0xFECD0000"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
End

TOKEN
	Name  = "EHCI_MMIO_BASE_ADDRESS2"
	Value  = "$(EHCI_MMIO_BASE_ADDRESS1)+0xC00"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
End

TOKEN
	Name  = "EHCI_MMIO_SIZE"
	Value  = "0x400"
	TokenType = Integer
	TargetH = Yes
	Token = "USB_DEBUG_TRANSPORT" "=" "1"
End

TOKEN
	Name  = "CLOCK_GENERATOR_ADDRESS"
	Value  = "0xD2"
	Help  = "Clock generator address. Set to 0xFF to disable\clock generator programming."
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name  = "CLOCK_GENERATOR_SETTINGS"
	Value  = "{0x35, 0x83, 0xFF, 0xFF, 0xFC, 0x00, 0x00, 0x26, 0x03, 0x25, 0xFD, 0x56, 0x0D}"
	Help  = "List of initial clock controller register settings for Desktop."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = " "
	TokenType = Integer
End

TOKEN
	Name  = "====== UEFI based Configuration ======"
	TokenType = Expression
End

TOKEN
	Name  = "OFFSET_0"
	Value  = "1"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" "<=" "0x20000"
End

TOKEN
	Name  = "OFFSET_0"
	Value  = "0"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" ">" "0x20000"
End

TOKEN
	Name  = "OFFSET_1"
	Value  = "2"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" "<=" "0x20000"
End

TOKEN
	Name  = "OFFSET_1"
	Value  = "1"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" ">" "0x20000"
End

TOKEN
	Name  = "OFFSET_2"
	Value  = "3"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" "<=" "0x20000"
End

TOKEN
	Name  = "OFFSET_2"
	Value  = "2"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" ">" "0x20000"
End

TOKEN
	Name  = "OFFSET_3"
	Value  = "4"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" "<=" "0x20000"
End

TOKEN
	Name  = "OFFSET_3"
	Value  = "3"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" ">" "0x20000"
End

TOKEN
	Name  = "OFFSET_4"
	Value  = "5"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" "<=" "0x20000"
End

TOKEN
	Name  = "OFFSET_4"
	Value  = "4"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" ">" "0x20000"
End

TOKEN
	Name  = "OFFSET_5"
	Value  = "6"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" "<=" "0x20000"
End

TOKEN
	Name  = "OFFSET_5"
	Value  = "5"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" ">" "0x20000"
End

TOKEN
	Name  = "OFFSET_6"
	Value  = "7"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" "<=" "0x20000"
End

TOKEN
	Name  = "OFFSET_6"
	Value  = "6"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" ">" "0x20000"
End

TOKEN
	Name  = "OFFSET_7"
	Value  = "8"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" "<=" "0x20000"
End

TOKEN
	Name  = "OFFSET_7"
	Value  = "7"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" ">" "0x20000"
End

TOKEN
	Name  = "OFFSET_8"
	Value  = "9"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" "<=" "0x20000"
End

TOKEN
	Name  = "OFFSET_8"
	Value  = "8"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" ">" "0x20000"
End

TOKEN
	Name  = "OFFSET_9"
	Value  = "10"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" "<=" "0x20000"
End

TOKEN
	Name  = "OFFSET_9"
	Value  = "9"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" ">" "0x20000"
End

TOKEN
	Name  = "OFFSET_10"
	Value  = "11"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" "<=" "0x20000"
End

TOKEN
	Name  = "OFFSET_10"
	Value  = "10"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" ">" "0x20000"
End

TOKEN
	Name  = "OFFSET_11"
	Value  = "12"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" "<=" "0x20000"
End

TOKEN
	Name  = "OFFSET_11"
	Value  = "11"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" ">" "0x20000"
End

TOKEN
	Name  = "OFFSET_12"
	Value  = "13"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" "<=" "0x20000"
End

TOKEN
	Name  = "OFFSET_12"
	Value  = "12"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" ">" "0x20000"
End

TOKEN
	Name  = "OFFSET_13"
	Value  = "14"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" "<=" "0x20000"
End

TOKEN
	Name  = "OFFSET_13"
	Value  = "13"
	Help  = "Offset 0 based in UEFI 2.1 and 1 based in UEFI 2.0"
	TokenType = Integer
	TargetMAK = Yes
	TargetH = Yes
	Token = "EFI_SPECIFICATION_VERSION" ">" "0x20000"
End

TOKEN
	Name  = " "
	TokenType = Integer
End

PATH
	Name  = "SB_CHIPSET_DIR"
	Path  = "Chipset\SB"
End

TOKEN
	Name  = "INTEL_SATA_ASL_FILE"
	Value  = "$(SB_CHIPSET_DIR)\SATA.asl"
	TokenType = Expression
	TargetMAK = Yes
End

TOKEN
	Name  = "INTEL_IDE_ASL_FILE"
	Value  = "$(SB_CHIPSET_DIR)\IDE.asl"
	TokenType = Expression
	TargetMAK = Yes
End

PATH
	Name  = "SB_BOARD_DIR"
	Path  = "Board\SB"
End

MODULE
	Help  = "Includes SB.mak to Project"
	File  = "SB.mak"
End

ELINK
	Name  = "SBPEIDBG_Initialize,"
	Parent  = "PeiDebuggerInitialize"
	Priority  = 10
	Token = "AMIDEBUG_RX_SUPPORT" "=" "1"
	Token = "PeiDebugger_SUPPORT" "=" "1"
	InvokeOrder = AfterParent
End

# Only for Mobile/ULT CRB >>>
TOKEN
	Name  = "CRB_UART_CONFIG"
	Value  = "1"
	Help  = "Only for Mobile/ULT CRB UART configuration"
	TokenType = Boolean
	TargetMAK = Yes
	Token = "PCH_SKU" "=" "1"
	Token = "CRB_SIO_SUPPORT" "=" "0"
	Token = "VirtualSerial_SUPPORT" "=" "1"
	Token = "DEBUG_MODE" "=" "1"
End

ELINK
	Name  = "SBPEIDBG_Initialize,"
	Parent  = "PeiCoreInitialize"
	Priority  = 10
	Token = "PCH_SKU" "=" "1"
	Token = "CRB_SIO_SUPPORT" "=" "0"
	Token = "VirtualSerial_SUPPORT" "=" "1"
	Token = "DEBUG_MODE" "=" "1"
	InvokeOrder = AfterParent
End
# Only for Mobile/ULT CRB <<<

ELINK
	Name  = "$(SB_CHIPSET_DIR)\SB.asl"
	Parent  = "INTEL_GENERIC_ASL"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "\_SB.PCI0.SBRG.SPTS(Arg0)"
	Parent  = "ASL_PTS"
	Help  = "Include South Bridge Specific Function at PTS.\Arg0 is a sleep state the System is targeted for."
	InvokeOrder = AfterParent
End

ELINK
	Name  = "\_SB.PCI0.SBRG.SWAK(Arg0)"
	Parent  = "ASL_WAK"
	Help  = "Include South Bridge Specific Function at WAK.\Arg0 is a sleep state the System is resuming from. "
	SrcFile  = "Chipset\SB\SB.ASL"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "/I$(SB_BOARD_DIR)"
	Parent  = "$(GLOBAL_DEFINES)"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "/I$(SB_CHIPSET_DIR)"
	Parent  = "$(GLOBAL_DEFINES)"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "$(BUILD_DIR)\SBPEI.ffs"
	Parent  = "FV_BB"
	Help  = "INTEL ICH7 SB PEI component"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "$(BUILD_DIR)\SBDXE.ffs"
	Parent  = "FV_MAIN"
	Help  = "INTEL ICH7 SB DXE component"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "$(BUILD_DIR)\SBRUN.ffs"
	Parent  = "FV_MAIN"
	Help  = "INTEL ICH7 SB Runtime DXE component"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "$(BUILD_DIR)\SBSATAIDE.ffs"
	Parent  = "FV_MAIN"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "$(BUILD_DIR)\SBSECInit.OBJ"
	Parent  = "ADDON_SEC_CORE_OBJ_FILES"
	Token = "INCLUDE_SB_ASM_FILE_IN_SEC" "=" "1"
	InvokeOrder = AfterParent
End

TOKEN
	Name  = "SBCSPLib"
	Value  = "$$(LIB_BUILD_DIR)\AmiSbCSPLib.lib"
	TokenType = Expression
	TargetMAK = Yes
End

ELINK
	Name  = "\_SB.SBPS(Arg0)"
	Parent  = "ASL_PTS"
	Help  = "Include South Bridge Specific Function at PTS."
	SrcFile  = "Chipset\SB\SLEEPBTN.ASL"
	Token = "SLEEP_BUTTON_SUPPORT" "=" "1"
	Token = "ACPI_SUPPORT" "=" "1"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "$(SB_CHIPSET_DIR)\RRIORDMA.ASL"
	Parent  = "INTEL_GENERIC_ASL"
	Help  = "Include LPC RRIO & RDMA ASL"
	Token = "ACPI_SUPPORT" "=" "1"
	Token = "ACPI_MODULE_VER" ">" "30"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "UsbDxeDebuggerInitialize"
	Token = "USB_DEBUG_TRANSPORT" "=" "1"
	InvokeOrder = ReplaceParent
End

ELINK
	Name  = "SBPEIDBG_InitUsbEhci,"
	Parent  = "PeiDebuggerInitialize"
	Priority  = 150
	Token = "USB_DEBUG_TRANSPORT" "=" "1"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "SBPEIDBG_InitUsbEhci,"
	Parent  = "UsbDxeDebuggerInitialize"
	Token = "USB_DEBUG_TRANSPORT" "=" "1"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "SBSmmSaveRestoreStates,"
	Parent  = "SmmSaveRestoreEnvironment"
	Token = "SMM_SUPPORT" "=" "1"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "{0, 0, 0x80, 0xff, ReadWriteCmosBank2},"
	Parent  = "CMOS_PORT_MAPPING"
	Help  = "Second bank CMOS access range (Registers in range: 0x80-0xff)"
	Token = "CMOS_MANAGER_SUPPORT" "=" "1"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "SbGetRtcPowerStatus"
	Parent  = "CMOS_BATTERY_TEST_MAPPING"
	Help  = "Link the standard function to determine whether or not the CMOS battery is good."
	Token = "CMOS_MANAGER_SUPPORT" "=" "1"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "$(SB_BOARD_DIR)\Sb.ssp"
	Parent  = "ADDON_SSP_FILES"
	Token = "CMOS_MANAGER_SUPPORT" "=" "1"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "SbConfigurationList"
	InvokeOrder = ReplaceParent
End

ELINK
	Name  = "SbTimerSaveRestoreRegistersCallbacks"
	InvokeOrder = ReplaceParent
End

ELINK
	Name  = "OEM_HDA_VERB_TABLE"
	InvokeOrder = ReplaceParent
End

ELINK
	Name  = "OEM_SPI_VSCC_TABLE"
	Help  = "{VidDid, Vscc}"
	InvokeOrder = ReplaceParent
End

ELINK
	Name  = "OEM_HDA_VERB_TABLE_CONTENT"
	InvokeOrder = ReplaceParent
End

ELINK
	Name  = "SBIsDefaultConfigMode,"
	Parent  = "IsResetConfigMode"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "OEM_PCI_DEVICE_CALLBACK(0, 0, SBProtectedPciDevice),"
	Parent  = "OEM_SKIP_PCI_DEVICE"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "OEM_PCI_DEVICE_CALLBACK(0, 0, SBProgramPciDevice),"
	Parent  = "OEM_PROGRAM_PCI_DEVICE"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "OEM_PCI_DEVICE_CALLBACK(0, 0, SBUpdatePciDeviceAttributes),"
	Parent  = "OEM_PCI_ATTRIBUTES"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "SECSB_EarlyInit"
	Parent  = "GainestownSecRcEntry"
	Help  = "SB Early Init in SEC (before Cache as memory enabling)"
	SrcFile  = "Board\SB\SBSECInit.ASM"
	Token = "INCLUDE_SB_ASM_FILE_IN_SEC" "=" "1"
	InvokeOrder = BeforeParent
End

ELINK
	Name  = "{0xFFFFFFFF, 0, 0xFF, FALSE, 1, 0, DummyVerbTable},"
	Parent  = "OEM_HDA_VERB_TABLE"
	Help  = "Dummy Verb Table"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "{0xEF4017, 0x2025},"
	Parent  = "OEM_SPI_VSCC_TABLE"
	Help  = "W25Q64"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "BiosLockEnableSMIFlashHook,"
	Parent  = "SMIFlashEndHandlerList"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "SbS3WarmResetLink"
	InvokeOrder = ReplaceParent
        Token = "SecureMod_SUPPORT" "=" "1"
End

ELINK
	Name  = "SBLib_BeforeShutdown,"
	Parent  = "SbS3WarmResetLink"
	InvokeOrder = AfterParent
  Token = "SecureMod_SUPPORT" "=" "1"
End

ELINK
	Name  = "BusOverrideGuidsforUefiRaid"
	InvokeOrder = ReplaceParent
End

ELINK
  Name  = "SbRuntimeResetElinkList"
  InvokeOrder = ReplaceParent
End

ELINK
	Name  = "{0xBB65942B,0x521F,0x4EC3,0xBA,0xF9,0xA9,0x25,0x40,0xCF,0x60,0xD2},"
	Parent  = "BusOverrideGuidsforUefiRaid"
	Help  = "FFS Guid of Satacontroller Driver"
	InvokeOrder = AfterParent
End

ELINK
	Name  = "{0x8F5A2E02,0x538C,0x4D59,0xB9,0x20,0xC4,0x78,0x6A,0xCB,0xC5,0x52},"
	Parent  = "BusOverrideGuidsforUefiRaid"
	Help  = "FFS Guid of AHCI Driver"
	InvokeOrder = AfterParent
End

TOKEN
	Name  = "DISABLE_DAYLIGHT_SAVINGS"
	Value = "0"
	Help  = "1: Disable Daylight Savings; 0: Enable Daylight Savings"
	TokenType = Expression
	TargetH = Yes
End


#*************************************************************************
#*************************************************************************
#**                                                                     **
#**        (C)Copyright 1985-2013, American Megatrends, Inc.            **
#**                                                                     **
#**                       All Rights Reserved.                          **
#**                                                                     **
#**      5555 Oakbrook Parkway, Suite 200, Norcross, GA 30093           **
#**                                                                     **
#**                       Phone: (770)-246-8600                         **
#**                                                                     **
#*************************************************************************
#*************************************************************************