#*************************************************************************
#*************************************************************************
#**                                                                     **
#**        (C)Copyright 1985-2011, American Megatrends, Inc.            **
#**                                                                     **
#**                       All Rights Reserved.                          **
#**                                                                     **
#**      5555 Oakbrook Parkway, Suite 200, Norcross, GA 30093           **
#**                                                                     **
#**                       Phone: (770)-246-8600                         **
#**                                                                     **
#*************************************************************************
#*************************************************************************

#*************************************************************************
# $Header: /Alaska/Projects/Intel/Haswell/LynxPoint_SharkBay-DT_Crb_1AQQW/CRB/CSP.sdl 5     4/24/13 2:49a Thomaschen $
#
# $Revision: 5 $
#
# $Date: 4/24/13 2:49a $
#*************************************************************************
# Revision History
# ----------------
# $Log: /Alaska/Projects/Intel/Haswell/LynxPoint_SharkBay-DT_Crb_1AQQW/CRB/CSP.sdl $
# 
# 5     4/24/13 2:49a Thomaschen
# add token "USB_CONTROLLERS_WITH_RMH"
# 
# 4     12/13/12 4:02a Wesleychen
# EIP#108566: Fixed ME will not work under debug mode.
# 
# 2     11/21/12 6:10a Wesleychen
# Fix FV_BB size over 1MB cannot boot.
# 
# 1     2/12/12 10:38p Victortu
# Intel SharkBay CRB initially releases.
# 
#*************************************************************************
TOKEN
	Name  = "USB_UHCI"
	Value  = "0"
	Help  = "Maximum number of UHCI controllers present in the system"
	TokenType = Integer
	TargetH = Yes
	Range  = "0-6"
End

TOKEN
	Name  = "USB_EHCI"
	Value  = "2"
	Help  = "Maximum number of EHCI controllers present in the system"
	TokenType = Integer
	TargetH = Yes
	Range  = "0-6"
End

TOKEN
	Name  = "USB_XHCI"
	Value  = "1"
	Help  = "Maximum number of supported XHCI controllers"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name  = "XHCI_EVENT_SERVICE_MODE"
	Value  = "0"
	Help  = "This token controlls xHCI event service mode.\0 - Use periodic timer SMI.\1 - Use xHCI hardware SMI.\2 - Both periodic timer SMI and se xHCI hardware SMI."
	TokenType = Integer
	TargetH = Yes
	Range  = "0..2"
End

TOKEN
	Name  = "USB_XHCI_EXT_HW_SMI_PINS"
	Value  = "255"
	Help  = "List of xHCI GPI bit offset in the following format: GPI0, GPI1,...,GPIN.\Use 0xFF (255) to ignore the settings."
	TokenType = Expression
	TargetH = Yes
	Range  = "0..31"
	Token = "XHCI_EVENT_SERVICE_MODE" "!=" "0"
End

TOKEN
	Name  = "EHCI_PCI_DEVICES"
	Value  = "{0xD0, 0x20}, {0xE8, 0x20}"
	Help  = "List of supported EHCI controllers in the following format: {dev1, 0}, {dev2, 0},...,{devN, 0}\dev represents the location of EHCI controller on PCI bus: dev = Bus << 8 + Dev << 3 + Func. Value followed by dev is the PCI device interface, for EHCI it must be 0x20.\Note: number of pairs {dev, 0} must not be less than a number of supported UHCI controllers specified in USB_UHCI token."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "XHCI_PCI_DEVICES"
	Value  = "{0xA0, 0x30}"
	Help  = "List of supported onchip XHCI controllers in the following format: {dev1, 0}, {dev2, 0},...,{devN, 0}\dev represents the location of XHCI controller on PCI bus: dev = Bus << 8 + Dev << 3 + Func. Value followed by dev is the PCI device interface, for XHCI it must be 0x30.\Note: number of pairs {dev, 0} must not be less than a number of supported EHCI controllers specified in USB_XHCI token."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "UHCI_PCI_DEVICES"
	Value  = "{0xD0, 0}, {0xD1, 0}, {0xD2, 0}, {0xD3, 0}, {0xE8, 0}, {0xE9, 0}, {0xEA, 0}, {0xEB, 0}, {0xEC, 0}"
	Help  = "List of supported UHCI controllers in the following format: {dev1, 0}, {dev2, 0},...,{devN, 0}\dev represents the location of UHCI controller on PCI bus: dev = Bus << 8 + Dev << 3 + Func. Value followed by dev is the PCI device interface, for UHCI it must be 0.\Note: number of pairs {dev, 0} must not be less than a number of supported UHCI controllers specified in USB_UHCI token."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
        Name  = "USB_CONTROLLERS_WITH_RMH"
        Value  = "{0x8086, 0x8C26}, {0x8086, 0x8C2D}" # for Intel Lynx Point
        Help  = "List of USB controllers that have integrated USB 2.0 Rate Matching Hubs (RMH) in the following format: {vid1, did1}, {vid2, did2}"
        TokenType = Expression
        TargetH = Yes
End

TOKEN
	Name  = "PEI_EHCI_PCI_BDFS"
	Value  = "{0x1A0000, 0x1D0000}"
	Help  = "List of supported EHCI controllers in the following format: {devfunc1, devfunc2,...,devfuncN}\devfunc represents the location of UHCI controller on PCI bus: dev = Bus << 24 + Dev << 16 + Func << 8. Value followed by dev is the PCI device interface, for UHCI it must be 0.\Note: number of entries {devfunc} must not be less than a number of supported EHCI controllers specified in PEI_NUM_EHCI token."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "PEI_UHCI_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable UHCI Controller support for USB recovery"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
End

TOKEN
	Name  = "PEI_EHCI_SUPPORT"
	Value  = "1"
	Help  = "Main switch to enable EhciPei support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
End

TOKEN
	Name  = "PEI_UHCI_PCI_DEVICES"
	Value  = "{0x1A0000, 0x1A0100, 0x1A0200, 0x1D0000, 0x1D0100, 0x1D0200, 0x1D0300}"
	Help  = "List of supported UHCI controllers in the following format: {devfunc1, devfunc2,...,devfuncN}\devfunc represents the location of UHCI controller on PCI bus: dev = Bus << 24 + Dev << 16 + Func << 8. Value followed by dev is the PCI device interface, for UHCI it must be 0.\Note: number of entries {devfunc} must not be less than a number of supported UHCI controllers specified in PEI_NUM_UHCI token."
	TokenType = Expression
	TargetH = Yes
	Token = "PEI_UHCI_SUPPORT" "=" "1"
End

TOKEN
	Name  = "PEI_EHCI_PCI_BDFS"
	Value  = "{0x1A0000, 0x1D0000}"
	Help  = "List of supported EHCI controllers in the following format: {devfunc1, devfunc2,...,devfuncN}\devfunc represents the location of EHCI controller on PCI bus: dev = Bus << 24 + Dev << 16 + Func << 8. Value followed by dev is the PCI device interface, for EHCI it must be 0.\Note: number of entries {devfunc} must not be less than a number of supported EHCI controllers specified in PEI_NUM_EHCI token."
	TokenType = Expression
	TargetH = Yes
	Token = "PEI_EHCI_SUPPORT" "=" "1"
End

TOKEN
	Name  = "PEI_EHCI_MEM_BASE_ADDRESSES"
	Value  = "{$(EHCI_MMIO_BASE_ADDRESS1), $(EHCI_MMIO_BASE_ADDRESS2)}"
	Help  = "List of supported EHCI controllers in the following format: {devfunc1, devfunc2,...,devfuncN}\devfunc represents the location of UHCI controller on PCI bus: dev = Bus << 24 + Dev << 16 + Func << 8. Value followed by dev is the PCI device interface, for UHCI it must be 0.\Note: number of entries {devfunc} must not be less than a number of supported EHCI controllers specified in USB_EHCI token."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "SMM_CACHE_SUPPORT"
	Value  = "1"
	Help  = "Enable/disable SMM Cache Support"
	TokenType = Boolean
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "FWHFlash_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable FWH Flash support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
End

TOKEN
	Name  = "LPCFlash_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable LPC Flash support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
End

TOKEN
	Name  = "CMOS_USES_STANDARD_BATTERY_TEST"
	Value  = "0"
	Help  = "Specifies whether or not to use CMOS Manager's default battery test function.  If a platform provides a different battery test function this token should be disabled."
	TokenType = Boolean
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "MAX_MANAGED_CMOS_ADDRESS"
	Value  = "256"
	Help  = "Last CMOS address + 1 use to specify the maximum address that is manages by CMOS Manager"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "SW_IRQ_GENERATION_REG"
	Value  = "$(PM_BASE_ADDRESS)+0x70"
	Help  = "Software IRQ generation regsiter from SB to generate the IRQ12 and IRQ1."
	TokenType = Integer
	TargetH = Yes
	Token = "IRQ_EMUL_SUPPORT" "=" "1"
End

TOKEN
	Name  = "IODECODETYPE"
	Value  = "0"
	Help  = "Check project actually who does IODecode Implement by :\1 - decode by OEM porting with eLink function(default),\0 - decode by chipset porting in SBGeneric.c"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
End

TOKEN
	Name  = "DUTY_OFFSET_VAL"
	Value  = "0"
	Help  = "The zero-based index of where the processor�s duty cycle setting is within the processor�s P_CNT register.\(for more information, ACPI SPEC)."
	TokenType = Integer
	TargetH = Yes
	Range  = "0-0xf0"
End

TOKEN
	Name  = "DUTY_WIDTH_VAL"
	Value  = "0"
	Help  = "The bit width of the processor�s duty cycle setting value in the P_CNT register. Each processor�s duty cycle setting\allows the software to select a nominal processor frequency below its absolute frequency.\(for more information, ACPI SPEC)."
	TokenType = Integer
	TargetH = Yes
	Range  = "0-0xff: depends on 'duty_offset'"
End

TOKEN
	Name  = "RESET_RUNTIME_SERVICES_SUPPORT"
	Value  = "0"
	Help  = "If ON includes in project CORE implementation of reset \services (from TimeAndReset.c). \Set to OFF to use stand alone reset driver."
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
	Token = "PchReset_SUPPORT" "=" "1"
End

TOKEN
	Name  = "RTC_RUNTIME_SERVICES_SUPPORT"
	Value  = "1"
	Help  = "If ON includes in project CORE implementation of RTC \services (from TimeAndReset.c). \Set to OFF to use stand alone RTC driver."
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
End

TOKEN
	Name  = "CODE_CACHE_SIZE"
	Value  = "0x100000"
	Help  = "Code Cache Size in SEC phase\This size must a multiple of 4k and must be 2^n size. Caching the entire flash will cause cache line evictions."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "TOTAL_FV_BB_SIZE"
	Value  = "$(FV_BB_BLOCKS)*$(FLASH_BLOCK_SIZE)"
	Help  = "Total FV_BB size in byte."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "CODE_CACHE_PART2_SIZE"
	Value  = "$(TOTAL_FV_BB_SIZE)-$(CODE_CACHE_SIZE)"
	Help  = "Turn on CODE_CACHE_PART2 when FV_BB size > CODE_CACHE_SIZE.\Code Cache PART 2 Size ."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "TOTAL_FV_BB_SIZE" ">" "0x100000"
End

TOKEN
	Name  = "CODE_CACHE_PART2_BASE"
	Value  = "0xffffffff-($(CODE_CACHE_SIZE)+$(CODE_CACHE_PART2_SIZE))+1"
	Help  = "Turn on CODE_CACHE_PART2 when FV_BB size > CODE_CACHE_SIZE.\Code Cache PART 2 Base Address. 0 = No PART 2"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "TOTAL_FV_BB_SIZE" ">" "0x100000"
End

TOKEN
	Name  = "NO_OF_PHYSICAL_MEMORY_ARRAY"
	Value  = "$(MEMORY_ARRAY_NUM)"
	Help  = "Specifies the Total number of Physical Arrays in the System."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Range  = "1 - 5"
End

TOKEN
	Name  = "ME_IGNITION_FW_MSG_SUPPORT"
	Value  = "0"
	Help  = "Enable this Token to Show Ignition FW status during POST"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "PowerButton_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable PowerButton support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
End

TOKEN
	Name  = "LIBEXE"
	Value  = "$(SILENT)LINK /LIB"
	TokenType = Expression
	TargetMAK = Yes
End

ELINK
	Name  = "$(BUILD_DIR)\UsbBotPeim.ffs"
	Parent  = "FV_BB"
	Token = "UsbRecov_SUPPORT" "=" "1"
	InvokeOrder = BeforeParent
End

ELINK
	Name  = "$(BUILD_DIR)\Recovery.ffs"
	Parent  = "FV_BB"
	Token = "Recovery_SUPPORT" "=" "1"
	InvokeOrder = BeforeParent
End

#*************************************************************************
#*************************************************************************
#**                                                                     **
#**        (C)Copyright 1985-2011, American Megatrends, Inc.            **
#**                                                                     **
#**                       All Rights Reserved.                          **
#**                                                                     **
#**      5555 Oakbrook Parkway, Suite 200, Norcross, GA 30093           **
#**                                                                     **
#**                       Phone: (770)-246-8600                         **
#**                                                                     **
#*************************************************************************
#*************************************************************************

##  k_prj begin
## Modules Disable
TOKEN
	Name  = "AmiGopPolicy"
	Value  = "0"
	Help  = "Main Switch to Enable AmiGopPolicy in Platform"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
#	Master = Yes
End
TOKEN
    Name  = "HARDWARE_SIGNATURE_MANAGEMENT_SUPPORT"
    Value  = "0"
    TokenType = Boolean
    TargetEQU = Yes
    TargetMAK = Yes
    TargetH = Yes
#    Master = Yes
    Help  = "Main switch to enable HardwareSignatureManagement support in Project"
End
TOKEN
	Name  = "CPPC_SUPPORT"
	Value  = "0"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
	Help  = "Main switch to enable CPPC supppory in Project"
End
TOKEN
	Name  = "ISCT_PLATFORM_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable ISCT support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
#	Master = Yes
End
TOKEN
	Name  = "IntelGigabitLan_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable Intel Gigabit Lan network chip support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
End
TOKEN
    Name  = "OemActivation_SUPPORT"
    Value = "0"
    Help  = "Main switch to enable OemActivation support in Project"
    TokenType = Boolean
    TargetH   = Yes
    TargetMAK = Yes
#    Master = Yes
End
TOKEN
    Name  = OpalSecurity_SUPPORT
    Value  = "0"
    TokenType = Boolean
    TargetMAK = Yes
    TargetH = Yes
#    Master = Yes
    Help  = "Main switch to enable OpalSecurity support in Project"
End
TOKEN
	Name  = "POST_TIME_TUNING_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable Post Time Tuning module in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
End
TOKEN
	Name  = "SecureBoot_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable SecureBoot Module support in Project"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
	Token = "CryptoAPI_SUPPORT" "=" "1"
End
TOKEN
	Name  = "SecureMod_SUPPORT"
	Value  = "0"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
	Token = "CryptoAPI_SUPPORT" "=" "1"
End
TOKEN
    Name  = "SECURE_FLASH_SUPPORT"
    Value  = "0"
    TokenType = Boolean
    TargetEQU = Yes
    TargetMAK = Yes
#    Master = Yes
    Help  = "Main switch to enable Security Flash in Project"
    Token = "SecSMIFlash_SUPPORT" "=" "1"
End
TOKEN
	Name  = "EcPs2Kbd_SUPPORT"
	Value  = "0"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
End
TOKEN
    Name  = "IdeSMART_Support"
    Value  = "0"
    Help  = "Main switch to enable IdeSMART support in Project"
    TokenType = Boolean
    TargetEQU = Yes
    TargetMAK = Yes
    TargetH = Yes
#    Master = Yes
End
TOKEN
    Name  = "HDD_SECURITY_SUPPORT"
    Value  = "0"
    Help  = "Main switch to enable Hdd Security support in Project"
    TokenType = Boolean
    TargetEQU = Yes
    TargetMAK = Yes
    TargetH = Yes
#    Master = Yes
End
TOKEN
	Name  = "AmiSgTPV_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable SwitchableGraphics TPV support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
        Token = "SwitchableGraphics_SUPPORT" "=" "1"
End
TOKEN
	Name  = "SwitchableGraphics_SUPPORT"
	Value  = "0"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
End
TOKEN
	Name  = "TCG2Support"
	Value  = "0"
	Help  = "Enable or Disable TCG_generic support"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
End
TOKEN
	Name  = "UefiNetworkStackII"
	Value  = "0"
	Help  = "Main switch to enable netwwork stack drivers support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
End

## Override
## CRB\CSP.sdl
TOKEN
	Name  = "PowerButton_SUPPORT"
	Value  = "1"
	Help  = "Main switch to enable PowerButton support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
End
ELINK
	Name  = "IsCtrlHomePressed,"
	Parent  = "IsRecovery"
	Help  = "Ctr+Home detection"
#	Token = "KBC_SUPPORT" "=" "1"
	InvokeOrder = AfterParent
	Disable = Yes
End
ELINK
	Name  = "IsRecoveryJumper,"
	Parent  = "IsRecovery"
	Help  = "CRB recovery jumper detection"
	InvokeOrder = AfterParent
	Disable = Yes
End
## CRB\CRB.sdl
ELINK
	Name  = "{0x10EC0888, 0, 0xFF, TRUE, 11, 2, CrbHdaVerbTbl8},"
	Parent  = "OEM_HDA_VERB_TABLE"
	Help  = "CRB HDA Verb Table"
#	Token = "CRB_HDA_VERB_TABLE_PRESENT" "=" "1"
	InvokeOrder = AfterParent
	Disable = Yes
End
ELINK
	Name  = "{0x10EC0885, 0, 0xFF, TRUE, 11, 2, CrbHdaVerbTbl9},"
	Parent  = "OEM_HDA_VERB_TABLE"
	Help  = "CRB HDA Verb Table"
#	Token = "CRB_HDA_VERB_TABLE_PRESENT" "=" "1"
	InvokeOrder = AfterParent
	Disable = Yes
End
ELINK
	Name  = "{0x10EC0889, 0, 0xFF, TRUE, 11, 2, CrbHdaVerbTbl10},"
	Parent  = "OEM_HDA_VERB_TABLE"
	Help  = "CRB HDA Verb Table"
#	Token = "CRB_HDA_VERB_TABLE_PRESENT" "=" "1"
	InvokeOrder = AfterParent
	Disable = Yes
End
TOKEN
	Name  = "BEEP_ENABLE"
	Value  = "1"
	Help  = "This flag enables/disables all firmware beeps"
	TokenType = Boolean
End

## ReferenceCode\ME\ActiveManagement\ActiveManagement.sdl
TOKEN
	Name  = "iAMT_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable iAMT support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
	Token = "iME_SUPPORT" "=" "1"
End