#*************************************************************************
#*************************************************************************
#**                                                                     **
#**        (C)Copyright 1985-2011, American Megatrends, Inc.            **
#**                                                                     **
#**                       All Rights Reserved.                          **
#**                                                                     **
#**      5555 Oakbrook Parkway, Suite 200, Norcross, GA 30093           **
#**                                                                     **
#**                       Phone: (770)-246-8600                         **
#**                                                                     **
#*************************************************************************
#*************************************************************************

#*************************************************************************
# $Header: /Alaska/Projects/Intel/Haswell/LynxPoint_SharkBay-DT_Crb_1AQQW/CRB/CSP.sdl 5     4/24/13 2:49a Thomaschen $
#
# $Revision: 5 $
#
# $Date: 4/24/13 2:49a $
#*************************************************************************
# Revision History
# ----------------
# $Log: /Alaska/Projects/Intel/Haswell/LynxPoint_SharkBay-DT_Crb_1AQQW/CRB/CSP.sdl $
# 
# 5     4/24/13 2:49a Thomaschen
# add token "USB_CONTROLLERS_WITH_RMH"
# 
# 4     12/13/12 4:02a Wesleychen
# EIP#108566: Fixed ME will not work under debug mode.
# 
# 2     11/21/12 6:10a Wesleychen
# Fix FV_BB size over 1MB cannot boot.
# 
# 1     2/12/12 10:38p Victortu
# Intel SharkBay CRB initially releases.
# 
#*************************************************************************
TOKEN
	Name  = "USB_UHCI"
	Value  = "0"
	Help  = "Maximum number of UHCI controllers present in the system"
	TokenType = Integer
	TargetH = Yes
	Range  = "0-6"
End

TOKEN
	Name  = "USB_EHCI"
	Value  = "2"
	Help  = "Maximum number of EHCI controllers present in the system"
	TokenType = Integer
	TargetH = Yes
	Range  = "0-6"
End

TOKEN
	Name  = "USB_XHCI"
	Value  = "1"
	Help  = "Maximum number of supported XHCI controllers"
	TokenType = Integer
	TargetH = Yes
End

TOKEN
	Name  = "XHCI_EVENT_SERVICE_MODE"
	Value  = "0"
	Help  = "This token controlls xHCI event service mode.\0 - Use periodic timer SMI.\1 - Use xHCI hardware SMI.\2 - Both periodic timer SMI and se xHCI hardware SMI."
	TokenType = Integer
	TargetH = Yes
	Range  = "0..2"
End

TOKEN
	Name  = "USB_XHCI_EXT_HW_SMI_PINS"
	Value  = "255"
	Help  = "List of xHCI GPI bit offset in the following format: GPI0, GPI1,...,GPIN.\Use 0xFF (255) to ignore the settings."
	TokenType = Expression
	TargetH = Yes
	Range  = "0..31"
	Token = "XHCI_EVENT_SERVICE_MODE" "!=" "0"
End

TOKEN
	Name  = "EHCI_PCI_DEVICES"
	Value  = "{0xD0, 0x20}, {0xE8, 0x20}"
	Help  = "List of supported EHCI controllers in the following format: {dev1, 0}, {dev2, 0},...,{devN, 0}\dev represents the location of EHCI controller on PCI bus: dev = Bus << 8 + Dev << 3 + Func. Value followed by dev is the PCI device interface, for EHCI it must be 0x20.\Note: number of pairs {dev, 0} must not be less than a number of supported UHCI controllers specified in USB_UHCI token."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "XHCI_PCI_DEVICES"
	Value  = "{0xA0, 0x30}"
	Help  = "List of supported onchip XHCI controllers in the following format: {dev1, 0}, {dev2, 0},...,{devN, 0}\dev represents the location of XHCI controller on PCI bus: dev = Bus << 8 + Dev << 3 + Func. Value followed by dev is the PCI device interface, for XHCI it must be 0x30.\Note: number of pairs {dev, 0} must not be less than a number of supported EHCI controllers specified in USB_XHCI token."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "UHCI_PCI_DEVICES"
	Value  = "{0xD0, 0}, {0xD1, 0}, {0xD2, 0}, {0xD3, 0}, {0xE8, 0}, {0xE9, 0}, {0xEA, 0}, {0xEB, 0}, {0xEC, 0}"
	Help  = "List of supported UHCI controllers in the following format: {dev1, 0}, {dev2, 0},...,{devN, 0}\dev represents the location of UHCI controller on PCI bus: dev = Bus << 8 + Dev << 3 + Func. Value followed by dev is the PCI device interface, for UHCI it must be 0.\Note: number of pairs {dev, 0} must not be less than a number of supported UHCI controllers specified in USB_UHCI token."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
        Name  = "USB_CONTROLLERS_WITH_RMH"
        Value  = "{0x8086, 0x8C26}, {0x8086, 0x8C2D}" # for Intel Lynx Point
        Help  = "List of USB controllers that have integrated USB 2.0 Rate Matching Hubs (RMH) in the following format: {vid1, did1}, {vid2, did2}"
        TokenType = Expression
        TargetH = Yes
End

TOKEN
	Name  = "PEI_EHCI_PCI_BDFS"
	Value  = "{0x1A0000, 0x1D0000}"
	Help  = "List of supported EHCI controllers in the following format: {devfunc1, devfunc2,...,devfuncN}\devfunc represents the location of UHCI controller on PCI bus: dev = Bus << 24 + Dev << 16 + Func << 8. Value followed by dev is the PCI device interface, for UHCI it must be 0.\Note: number of entries {devfunc} must not be less than a number of supported EHCI controllers specified in PEI_NUM_EHCI token."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "PEI_UHCI_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable UHCI Controller support for USB recovery"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
End

TOKEN
	Name  = "PEI_EHCI_SUPPORT"
	Value  = "1"
	Help  = "Main switch to enable EhciPei support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
End

TOKEN
	Name  = "PEI_UHCI_PCI_DEVICES"
	Value  = "{0x1A0000, 0x1A0100, 0x1A0200, 0x1D0000, 0x1D0100, 0x1D0200, 0x1D0300}"
	Help  = "List of supported UHCI controllers in the following format: {devfunc1, devfunc2,...,devfuncN}\devfunc represents the location of UHCI controller on PCI bus: dev = Bus << 24 + Dev << 16 + Func << 8. Value followed by dev is the PCI device interface, for UHCI it must be 0.\Note: number of entries {devfunc} must not be less than a number of supported UHCI controllers specified in PEI_NUM_UHCI token."
	TokenType = Expression
	TargetH = Yes
	Token = "PEI_UHCI_SUPPORT" "=" "1"
End

TOKEN
	Name  = "PEI_EHCI_PCI_BDFS"
	Value  = "{0x1A0000, 0x1D0000}"
	Help  = "List of supported EHCI controllers in the following format: {devfunc1, devfunc2,...,devfuncN}\devfunc represents the location of EHCI controller on PCI bus: dev = Bus << 24 + Dev << 16 + Func << 8. Value followed by dev is the PCI device interface, for EHCI it must be 0.\Note: number of entries {devfunc} must not be less than a number of supported EHCI controllers specified in PEI_NUM_EHCI token."
	TokenType = Expression
	TargetH = Yes
	Token = "PEI_EHCI_SUPPORT" "=" "1"
End

TOKEN
	Name  = "PEI_EHCI_MEM_BASE_ADDRESSES"
	Value  = "{$(EHCI_MMIO_BASE_ADDRESS1), $(EHCI_MMIO_BASE_ADDRESS2)}"
	Help  = "List of supported EHCI controllers in the following format: {devfunc1, devfunc2,...,devfuncN}\devfunc represents the location of UHCI controller on PCI bus: dev = Bus << 24 + Dev << 16 + Func << 8. Value followed by dev is the PCI device interface, for UHCI it must be 0.\Note: number of entries {devfunc} must not be less than a number of supported EHCI controllers specified in USB_EHCI token."
	TokenType = Expression
	TargetH = Yes
End

TOKEN
	Name  = "SMM_CACHE_SUPPORT"
	Value  = "1"
	Help  = "Enable/disable SMM Cache Support"
	TokenType = Boolean
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "FWHFlash_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable FWH Flash support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
End

TOKEN
	Name  = "LPCFlash_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable LPC Flash support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
End

TOKEN
	Name  = "CMOS_USES_STANDARD_BATTERY_TEST"
	Value  = "0"
	Help  = "Specifies whether or not to use CMOS Manager's default battery test function.  If a platform provides a different battery test function this token should be disabled."
	TokenType = Boolean
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "MAX_MANAGED_CMOS_ADDRESS"
	Value  = "256"
	Help  = "Last CMOS address + 1 use to specify the maximum address that is manages by CMOS Manager"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "SW_IRQ_GENERATION_REG"
	Value  = "$(PM_BASE_ADDRESS)+0x70"
	Help  = "Software IRQ generation regsiter from SB to generate the IRQ12 and IRQ1."
	TokenType = Integer
	TargetH = Yes
	Token = "IRQ_EMUL_SUPPORT" "=" "1"
End

TOKEN
	Name  = "IODECODETYPE"
	Value  = "0"
	Help  = "Check project actually who does IODecode Implement by :\1 - decode by OEM porting with eLink function(default),\0 - decode by chipset porting in SBGeneric.c"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
End

TOKEN
	Name  = "DUTY_OFFSET_VAL"
	Value  = "0"
	Help  = "The zero-based index of where the processor�s duty cycle setting is within the processor�s P_CNT register.\(for more information, ACPI SPEC)."
	TokenType = Integer
	TargetH = Yes
	Range  = "0-0xf0"
End

TOKEN
	Name  = "DUTY_WIDTH_VAL"
	Value  = "0"
	Help  = "The bit width of the processor�s duty cycle setting value in the P_CNT register. Each processor�s duty cycle setting\allows the software to select a nominal processor frequency below its absolute frequency.\(for more information, ACPI SPEC)."
	TokenType = Integer
	TargetH = Yes
	Range  = "0-0xff: depends on 'duty_offset'"
End

TOKEN
	Name  = "RESET_RUNTIME_SERVICES_SUPPORT"
	Value  = "0"
	Help  = "If ON includes in project CORE implementation of reset \services (from TimeAndReset.c). \Set to OFF to use stand alone reset driver."
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
	Token = "PchReset_SUPPORT" "=" "1"
End

TOKEN
	Name  = "RTC_RUNTIME_SERVICES_SUPPORT"
	Value  = "1"
	Help  = "If ON includes in project CORE implementation of RTC \services (from TimeAndReset.c). \Set to OFF to use stand alone RTC driver."
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
End

TOKEN
	Name  = "CODE_CACHE_SIZE"
	Value  = "0x100000"
	Help  = "Code Cache Size in SEC phase\This size must a multiple of 4k and must be 2^n size. Caching the entire flash will cause cache line evictions."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "TOTAL_FV_BB_SIZE"
	Value  = "$(FV_BB_BLOCKS)*$(FLASH_BLOCK_SIZE)"
	Help  = "Total FV_BB size in byte."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

TOKEN
	Name  = "CODE_CACHE_PART2_SIZE"
	Value  = "$(TOTAL_FV_BB_SIZE)-$(CODE_CACHE_SIZE)"
	Help  = "Turn on CODE_CACHE_PART2 when FV_BB size > CODE_CACHE_SIZE.\Code Cache PART 2 Size ."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "TOTAL_FV_BB_SIZE" ">" "0x100000"
End

TOKEN
	Name  = "CODE_CACHE_PART2_BASE"
	Value  = "0xffffffff-($(CODE_CACHE_SIZE)+$(CODE_CACHE_PART2_SIZE))+1"
	Help  = "Turn on CODE_CACHE_PART2 when FV_BB size > CODE_CACHE_SIZE.\Code Cache PART 2 Base Address. 0 = No PART 2"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Token = "TOTAL_FV_BB_SIZE" ">" "0x100000"
End

TOKEN
	Name  = "NO_OF_PHYSICAL_MEMORY_ARRAY"
	Value  = "$(MEMORY_ARRAY_NUM)"
	Help  = "Specifies the Total number of Physical Arrays in the System."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Range  = "1 - 5"
End

TOKEN
	Name  = "ME_IGNITION_FW_MSG_SUPPORT"
	Value  = "0"
	Help  = "Enable this Token to Show Ignition FW status during POST"
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "PowerButton_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable PowerButton support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
End

TOKEN
	Name  = "LIBEXE"
	Value  = "$(SILENT)LINK /LIB"
	TokenType = Expression
	TargetMAK = Yes
End

ELINK
	Name  = "$(BUILD_DIR)\UsbBotPeim.ffs"
	Parent  = "FV_BB"
	Token = "UsbRecov_SUPPORT" "=" "1"
	InvokeOrder = BeforeParent
End

ELINK
	Name  = "$(BUILD_DIR)\Recovery.ffs"
	Parent  = "FV_BB"
	Token = "Recovery_SUPPORT" "=" "1"
	InvokeOrder = BeforeParent
End

#*************************************************************************
#*************************************************************************
#**                                                                     **
#**        (C)Copyright 1985-2011, American Megatrends, Inc.            **
#**                                                                     **
#**                       All Rights Reserved.                          **
#**                                                                     **
#**      5555 Oakbrook Parkway, Suite 200, Norcross, GA 30093           **
#**                                                                     **
#**                       Phone: (770)-246-8600                         **
#**                                                                     **
#*************************************************************************
#*************************************************************************

##  k_prj begin
## Modules Disable
TOKEN
	Name  = "AmiGopPolicy"
	Value  = "0"
	Help  = "Main Switch to Enable AmiGopPolicy in Platform"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
#	Master = Yes
End
TOKEN
    Name  = "HARDWARE_SIGNATURE_MANAGEMENT_SUPPORT"
    Value  = "0"
    TokenType = Boolean
    TargetEQU = Yes
    TargetMAK = Yes
    TargetH = Yes
#    Master = Yes
    Help  = "Main switch to enable HardwareSignatureManagement support in Project"
End
TOKEN
	Name  = "CPPC_SUPPORT"
	Value  = "0"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
	Help  = "Main switch to enable CPPC supppory in Project"
End
TOKEN
	Name  = "ISCT_PLATFORM_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable ISCT support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
#	Master = Yes
End
TOKEN
	Name  = "IntelGigabitLan_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable Intel Gigabit Lan network chip support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
End
TOKEN
    Name  = "OemActivation_SUPPORT"
    Value = "0"
    Help  = "Main switch to enable OemActivation support in Project"
    TokenType = Boolean
    TargetH   = Yes
    TargetMAK = Yes
#    Master = Yes
End
TOKEN
    Name  = OpalSecurity_SUPPORT
    Value  = "0"
    TokenType = Boolean
    TargetMAK = Yes
    TargetH = Yes
#    Master = Yes
    Help  = "Main switch to enable OpalSecurity support in Project"
End
TOKEN
	Name  = "POST_TIME_TUNING_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable Post Time Tuning module in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
End
TOKEN
	Name  = "SecureBoot_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable SecureBoot Module support in Project"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
	Token = "CryptoAPI_SUPPORT" "=" "1"
End
TOKEN
	Name  = "SecureMod_SUPPORT"
	Value  = "0"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
	Token = "CryptoAPI_SUPPORT" "=" "1"
End
TOKEN
    Name  = "SECURE_FLASH_SUPPORT"
    Value  = "0"
    TokenType = Boolean
    TargetEQU = Yes
    TargetMAK = Yes
#    Master = Yes
    Help  = "Main switch to enable Security Flash in Project"
    Token = "SecSMIFlash_SUPPORT" "=" "1"
End
TOKEN
	Name  = "EcPs2Kbd_SUPPORT"
	Value  = "0"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
End
TOKEN
    Name  = "IdeSMART_Support"
    Value  = "0"
    Help  = "Main switch to enable IdeSMART support in Project"
    TokenType = Boolean
    TargetEQU = Yes
    TargetMAK = Yes
    TargetH = Yes
#    Master = Yes
End
TOKEN
    Name  = "HDD_SECURITY_SUPPORT"
    Value  = "0"
    Help  = "Main switch to enable Hdd Security support in Project"
    TokenType = Boolean
    TargetEQU = Yes
    TargetMAK = Yes
    TargetH = Yes
#    Master = Yes
End
TOKEN
	Name  = "AmiSgTPV_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable SwitchableGraphics TPV support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
        Token = "SwitchableGraphics_SUPPORT" "=" "1"
End
TOKEN
	Name  = "SwitchableGraphics_SUPPORT"
	Value  = "0"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
End
TOKEN
	Name  = "TCG2Support"
	Value  = "0"
	Help  = "Enable or Disable TCG_generic support"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
End
TOKEN
	Name  = "UefiNetworkStackII"
	Value  = "0"
	Help  = "Main switch to enable netwwork stack drivers support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
End
TOKEN
    Name  = "NVMe_SUPPORT"
    Value  = "0"
    Help  = "Main switch to enable NVMe support in Project"
    TokenType = Boolean
    TargetEQU = Yes
    TargetH = Yes
#    Master = Yes
End
TOKEN
	Name  = ACOUSTIC_MANAGEMENT_DRIVER_SUPPORT
	Value  = "0"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
	Help  = "Main switch to enable Acoustic Management support in Project"
End
TOKEN
	Name  = "PfatServices_SUPPORT"
	Value  = "0"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
    TargetH   = Yes
#	Master = Yes
	Help  = "Main switch to enable Pfat support in Project, needs NvramSmiSupport Enabled"
    Token = "NvramSmiSupport" "=" "1"
End
TOKEN
	Name  = "NFC_SUPPORT_DXE_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable NfcSupportDxe support in DXE Phase"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
End

## Override
## CRB\CSP.sdl
TOKEN
	Name  = "PowerButton_SUPPORT"
	Value  = "1"
	Help  = "Main switch to enable PowerButton support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
End
ELINK
	Name  = "IsCtrlHomePressed,"
	Parent  = "IsRecovery"
	Help  = "Ctr+Home detection"
#	Token = "KBC_SUPPORT" "=" "1"
	InvokeOrder = AfterParent
	Disable = Yes
End

## CRB\CRB.sdl
ELINK
	Name  = "{0x10EC0662, 0, 0xFF, TRUE, 11, 2, ZprjHdaVerbTbl},"
	Parent  = "OEM_HDA_VERB_TABLE"
	Help  = "CRB HDA Verb Table"
	Token = "CRB_HDA_VERB_TABLE_PRESENT" "=" "1"
	InvokeOrder = AfterParent
End
TOKEN
	Name  = "BEEP_ENABLE"
	Value  = "1"
	Help  = "This flag enables/disables all firmware beeps"
	TokenType = Boolean
	TargetH = Yes
	TargetEQU = Yes
	TargetMAK = Yes
End
TOKEN
	Name  = "ISA_IRQ_MASK"
	Value  = "0xE305"
	Help  = "This is an IRQ mask which may be used by ISA devices\ If BIT == 0 IRQ Available BIT == 1 IRQ Used.\DEFAULT VALUE == 0xE305."
	TokenType = Integer
	TargetH = Yes
	Range  = "0...0FFFFh"
End


## ReferenceCode\ME\ActiveManagement\ActiveManagement.sdl
TOKEN
	Name  = "iAMT_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable iAMT support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
	Token = "iME_SUPPORT" "=" "1"
End

## RomImage\RomImage.sdl
TOKEN
    Name  = "Q87_SKU_BUILD_SET"
    Value  = "$(Me_Q87_Xml) 0 Q87"
    Help  = "FitcBuild <MeXmlFile> <MeFwSelect> <MeFwSku> <FlashCount> <FlashSize1> <FlashSize2>\<MeFwSelect>:0 = 1.5MB ME Firmware, 1 = 5MB ME Firmware.\<MeFwSku>:Z87_SKU, Z85_SKU, Q87_SKU, H87_SKU, Q85_SKU, B85_SKU, H81_SKU.\<MeFwSku>:Use Xml file need give a name, this name do not use XXXX_SKU.\<FlashCount>:1 = One image, 2 = Two image.\<FlashSize1>:0=512KB,1=1MB,2=2MB,3=4MB,4=8MB,5=16MB.\<FlashSize2>:0=512KB,1=1MB,2=2MB,3=4MB,4=8MB,5=16MB."
    TokenType = Expression
    TargetMAK = Yes
    Token = "Q87_SKU" "=" "1"
End
TOKEN
    Name  = "H87_SKU"
    Value  = "0"
    Help  = "On/Off build this image."
    TokenType = Boolean
    TargetMAK = Yes
    Token = "SELECT_BUILD_PLATFORM" "=" "1"
End

## Board\NB\NB.sdl
PCIDEVICE
	Title  = "I.G.F.X."
	Bus  = 00h
	Dev  = 02h
	Fun  = 00h
	ROMFile  = "Chipset\NB\hsw_1039.dat"
	DeviceID  = 0402h
	VendorID  = 08086h
	IntA = 	LNKA; 16
	DeviceType = OnBoard
	PCIBusSize = 32bit
	OptionROM = Yes
	CompressedROM = Yes
End

## Board\SB\SB.sdl
IRQLINK
	Name  = "LNKA"
	Reg  = 060h
	IrqList  = 3,4,5,6,7,10,11,12,14,15
	InterruptType = LevelLow
End
IRQLINK
	Name  = "LNKB"
	Reg  = 061h
	IrqList  = 3,4,5,6,7,10,11,12,14,15
	InterruptType = LevelLow
End
IRQLINK
	Name  = "LNKC"
	Reg  = 062h
	IrqList  = 3,4,5,6,7,10,11,12,14,15
	InterruptType = LevelLow
End
IRQLINK
	Name  = "LNKD"
	Reg  = 063h
	IrqList  = 3,4,5,6,7,10,11,12,14,15
	InterruptType = LevelLow
End
IRQLINK
	Name  = "LNKE"
	Reg  = 068h
	IrqList  = 3,4,5,6,7,10,11,12,14,15
	InterruptType = LevelLow
End
IRQLINK
	Name  = "LNKF"
	Reg  = 069h
	IrqList  = 3,4,5,6,7,10,11,12,14,15
	InterruptType = LevelLow
End
IRQLINK
	Name  = "LNKG"
	Reg  = 06ah
	IrqList  = 3,4,5,6,7,10,11,12,14,15
	InterruptType = LevelLow
End
IRQLINK
	Name  = "LNKH"
	Reg  = 06bh
	IrqList  = 3,4,5,6,7,10,11,12,14,15
	InterruptType = LevelLow
End
PCIDEVICE
	Title  = "GbE Controller"
	Bus  = 00h
	Dev  = 019h
	Fun  = 00h
	ROMFile  = "Chipset\SB\GbE_OR.BIN"
	DeviceID  = 01502h
	VendorID  = 08086h
	IntA = 	LNKE; 20
	DeviceType = OnBoard
	PCIBusSize = 32bit
	OptionROM = Yes
	CompressedROM = Yes
	LinkDevice = Yes
	Disable = Yes
End
TOKEN
	Name  = "PCH_PWR_OPT_GBE"
	Value  = "0"
	Help  = "0:Set the function to 'Disabled'.\1:Set the function to 'Enabled'."
	TokenType = Boolean
	TargetH = Yes
End
TOKEN
	Name = "SB_IO_DECODE_IN_SEC"
	Value = "1"
	Help = "The value of SIO_PME_BASE_ADDRESS, '0' means no function."
	TokenType = Boolean
	TargetEQU = Yes
End
TOKEN
	Name = "SB_GEN_DECODE_RANGE_1"
	Value = "0x200"
	Help = "The value of SIO_PME_BASE_ADDRESS, '0' means no function."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Range = "00 - 0FFFFh"
	Token = "SB_IO_DECODE_IN_SEC" "=" "1"
End
TOKEN
	Name = "SB_GEN_DECODE_RANGE_2"
	Value = "0xA00"
	Help = "The value of SIO_PME_BASE_ADDRESS, '0' means no function."
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
	Range = "00 - 0FFFFh"
	Token = "SB_IO_DECODE_IN_SEC" "=" "1"
End

## Program PCH GPIO
TOKEN
	Name = "PROGRAM_GPIO_TYPE"
	Value = "1"
	Help = "0:use array directly/1:use token define"
	TokenType = Boolean
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_000"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_001"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_002"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_003"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_004"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_005"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_006"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_007"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_008"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_009"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_010"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_011"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_012"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_013"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_014"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_015"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_016"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_017"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_018"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_019"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_020"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_021"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_022" ## LAN1_DISABLE#
	Value = "$(GPO_HIGH)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_023"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_024"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_025"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_026"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_027"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_028"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_029"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_030"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_031"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_032"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_033"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_034"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_035"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_036"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_037"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_038" ## LAN2_DISABLE#
	Value = "$(GPO_HIGH)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_039" ## BOARD_ID
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_040"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_041"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_042"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_043"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_044"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_045"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_046"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_048" ## BOARD_ID
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_049"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_050" ## Connected to TPM Header
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_051"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_052"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_053"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_054"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_055"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_057"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_058" ## SML1CLK
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_059"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_060"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_061"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_062"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_063"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_064"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_065"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_066"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_067"
	Value = "$(IS_NOT_GPIO)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_068"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_069"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_070"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_071"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_072"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_073"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_074"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name = "GPIO_075"
	Value = "$(IS_GPIO)+$(IS_GPI)"
	Help = "[0]:GPIO USE Select - 0:Native Mode/1:GPIO Mode.;\[1]:GPIO Input/Output Select.\[2]:GPIO Level Select.\[3]:GPIO Signal Invert(Only For GPIO_00~31).\[4]:GPIO Blink Enable(Only For GPIO_00~31).\[5]:GPIO Reset Select.\[15:6]:RESERVED"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End

## Board\IO\F81866\IO_F81866.SDL
TOKEN
	Name  = "BOARD_LABEL_BELOW_25"
	Value  = "0"
	Help  = "Enable(Core<=4.6.4.0)/Disable(Core > 4.6.4.0 have defined AMI_CALLBACK_VARSTORE)"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
End
TOKEN
	Name  = "F81866_FLOPPY_PORT_PRESENT"
	Value  = "0"
	Help  = "Floppy Port Present / Not Present."
	TokenType = Boolean
	TargetH = Yes
End
TOKEN
	Name  = "F81866_PARALLEL_PORT_PRESENT"
	Value  = "1"
	Help  = "LPT Port Present / Not Present."
	TokenType = Boolean
	TargetH = Yes
End
TOKEN
	Name  = "F81866_IBEX_SUPPORT"
	Value  = "0"
	Help  = "Intel PECI 1/0 support/not"
	TokenType = Boolean
	TargetH = Yes
#	Token = "F81866_HWM_PRESENT" "=" "1"
End
TOKEN
	Name  = "F81866_T2_MODE"
	Value  = "0"
	Help  = "0: TEMP2 is connected to a thermistor.\1: TEMP2 is connected to a BJT. (default)"
	TokenType = Integer
	TargetH = Yes
End
TOKEN
	Name  = "F81866_T1_MODE"
	Value  = "0"
	Help  = "0: TEMP1 is connected to a thermistor\1: TEMP1 is connected to a BJT.(default)"
	TokenType = Integer
	TargetH = Yes
End
TOKEN
	Name  = "F81866_SMF_SUPPORT"
	Value  = "1"
	Help  = "F81866 SmartFan control support"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
	Token = "F81866_HWM_PRESENT" "=" "1"
End

## Board\IO\F81216\IO_F81216.SDL
TOKEN
	Name  = "F81216SEC_CLOCK"
	Value  = "1"
	Help  = "1/0 for 48Mhz/24MHz"
	TokenType = Integer
	TargetH = Yes
End
TOKEN
	Name  = "F81216SEC_CONFIG_INDEX"
	Value  = "0x4E"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name  = "F81216SEC_CONFIG_DATA"
	Value  = "0x4F"
	TokenType = Integer
	TargetEQU = Yes
	TargetH = Yes
End
TOKEN
	Name  = "F81216SEC_CONFIG_MODE_ENTER_VALUE"
	Value  = "0x87"
	Help  = "Value to enter Configuration Mode.Please check your hardware\Default is 0x77.\others are 0xA0, 0x87, 0x67"
	TokenType = Integer
	TargetH = Yes
End

## Core\EM\Recovery\Recovery.sdl
TOKEN
	Name  = "Recovery_SUPPORT"
	Value  = "0"
	Help  = "Main switch to enable Recovery support in Project"
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
#	Master = Yes
End

ELINK
	Name  = "{ CLOCK_SRC0, PCI_FUNCTION_NUMBER_PCH_PCIE_ROOT_PORT_1, 0 },"
	Parent  = "PCIEClockConfig"
	InvokeOrder = AfterParent
	Help  = "Intel Flathead Creek, PCIE Slot#6(J13BU)"
End
ELINK
	Name  = "{ CLOCK_SRC1, PCI_FUNCTION_NUMBER_PCH_PCIE_ROOT_PORT_2, 0 },"
	Parent  = "PCIEClockConfig"
	InvokeOrder = AfterParent
	Help  = "Intel Flathead Creek, PCIE Slot#6(J13BU)"
End
ELINK
	Name  = "{ CLOCK_SRC2, PCI_FUNCTION_NUMBER_PCH_PCIE_ROOT_PORT_3, 0 },"
	Parent  = "PCIEClockConfig"
	InvokeOrder = AfterParent
	Help  = "Intel Flathead Creek, PCIE Slot#6(J13BU)"
End

ELINK
	Name  = "ConInAvailabilityBeep,"
	Parent  = "/* Connect ConIn Devices */"
#	Token = "BEEP_ENABLE" "=" "1"
	InvokeOrder = AfterParent
End
ELINK
	Name  = "BeepService,"
	Parent  = "ReportMiscStatus"
#	Token = "BEEP_ENABLE" "=" "1"
	InvokeOrder = AfterParent
End
ELINK
	Name  = "BeepStatus,"
	Parent  = "ReportSimpleStatus"
#	Token = "BEEP_ENABLE" "=" "1"
	InvokeOrder = AfterParent
End

TOKEN
	Name  = "PASSWORD_MIN_SIZE"
	Value  = "8"
	TokenType = Integer
	TargetH = Yes
End
TOKEN
	Name  = "SETUP_PASSWORD_LENGTH"
	Value  = "12"
	Help  = "Default maximum password length. TSE Source needed to change the length"
	TokenType = Integer
	TargetH = Yes
End
TOKEN
	Name  = "SETUP_ENTRY_SCAN"
	Value  = "EFI_SCAN_F11"
	Help  = "Set to one of the defined constants from EFI_SIMPLE_TEXT_INPUT protocol. Remember to check STR_DEL_ENTER_SETUP string in MiniSetupStr.uni."
	TokenType = Expression
	TargetH = Yes
End
TOKEN
	Name  = "POPUP_MENU_ENTRY_SCAN"
	Value  = "EFI_SCAN_F10"
	Help  = "Set to one of the defined constants from EFI_SIMPLE_TEXT_INPUT protocol"
	TokenType = Expression
	TargetH = Yes
	Token = "SETUP_BBS_POPUP_ENABLE" "!=" "0"
End
TOKEN
	Name  = "TSE_DEFAULT_SETUP_PASSWORD_SUPPORT"
	Value  = "1"
	Help  = "0 is default.set 1=> to Enable default setup password"
	TokenType = Expression
	TargetH = Yes
	TargetMAK = Yes
End
TOKEN
	Name  = "DEFAULT_SETUP_PWD_AT_FIRSTBOOT_ONLY"
	Value  = "0"
	Help  = "1 is default. 1 => Sets the TSE_ADMIN_PASSWORD and TSE_USER_PASSWORD at first boot only. 0 => Sets TSE_ADMIN_PASSWORD and TSE_USER_PASSWORD in TSE defaults, on load defaults these data will be loaded"
	TokenType = Expression
	TargetH = Yes
	TargetMAK = Yes
	Token = "TSE_DEFAULT_SETUP_PASSWORD_SUPPORT" "=" "1"
End
TOKEN
	Name  = "TSE_ADMIN_PASSWORD"
	Value  = "Grg90#@B"
	Help  = "Defaultly no password is given. Need TSE source to change this. Provide data to set as default admin password. Maximum string can be provide is based on SETUP_PASSWORD_LENGTH token. String should be atleat minimum length mentioned in vfr. If no password is given it will not set any default password. Note: specify EMPTY_DATA in value if default admin password is not required"
	TokenType = Expression
	TargetH = Yes
	TargetMAK = Yes
	Token = "TSE_DEFAULT_SETUP_PASSWORD_SUPPORT" "=" "1"
End
TOKEN
	Name  = "TSE_DONOT_LOAD_PASSWORD_ON_DEFAULTS"
	Value  = "1"
	Help  = "1 => Will not load defaults for password when we press F3. 0 => Load default passowrd."
	TokenType = Boolean
	TargetH = Yes
End

TOKEN
	Name  = "TSE_SUPPORT_NATIVE_RESOLUTION"
	Value  = "0"
	Help  = "Sets the graphics mode for quiet boot from EDID. 1 - Defaultly enable make 0 to disable the feature"
	TokenType = Boolean
	TargetH = Yes
End
TOKEN
	Name  = "GC_MODE0"
	Value  = "{ 0, 80, 25, 640, 480 }"
	Help  = "Parameters of the graphica console text mode 0.\NOTE: Text resolution of the mode 0 must be 80 by 25\Format: {ModeNumber, TextColomns,TextRows, HorizontalPixels,VerticalPixels}"
	TokenType = Expression
	TargetH = Yes
#	Token = "WIN8_FEATURE_SUPPORT" "=" "1"
End
TOKEN
	Name  = "SETUP_JPEG_LOGO_SUPPORT"
	Value  = "1"
	Help  = "JPEG Logo support in Setup."
	TokenType = Boolean
	TargetEQU = Yes
	TargetMAK = Yes
	TargetH = Yes
End
TOKEN
	Name  = "SETUP_BMP_LOGO_SUPPORT"
	Value  = "0"
	Help  = "BMP Logo support in Setup"
	TokenType = Boolean
	TargetMAK = Yes
	TargetH = Yes
End
TOKEN
	Name  = "LOGO_FILE_NAME"
	Value  = "BIOS_CUSTOM\logo.jpg"
	TokenType = Expression
	TargetMAK = Yes
End

TOKEN
    Name  = "SLP_MARKER_ROM_FILENAME"
    Value = "BIOS_CUSTOM\OA20Marker.bin"
    Help  = "SLP2.0 Marker key rom file"
    TokenType = File
    TargetMAK = Yes
End
TOKEN
    Name  = "SLP_PUBKEY_ROM_FILENAME"
    Value = "BIOS_CUSTOM\OA20PubKey.bin"
    Help  = "SLP2.0 Public key rom file"
    TokenType = File
    TargetMAK = Yes
End
TOKEN
    Name = "SLP_STRING"
    Value = "GRGBankingIPC1"
    Help = "SLP string."
    TokenType = Expression
	TargetEQU = Yes
End