Merging patches from Yinghai Lu (fb2_s4882_changes.diff.bz2):

- new motherboard: Tyan s4882
- minor changes to 2880, s2881, s2885, s4880


git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1474 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1

20 files changed, 1430 insertions, 29 deletions

diff --git a/src/mainboard/tyan/s2880/Config.lb b/src/mainboard/tyan/s2880/Config.lb
index 275170ac9f..892429686d 100644
--- a/src/mainboard/tyan/s2880/Config.lb
+++ b/src/mainboard/tyan/s2880/Config.lb
@@ -32,7 +32,7 @@ default LB_CKS_LOC=123
 
 
 driver mainboard.o
-#driver lsi_scsi.o
+driver lsi_scsi.o
 #driver adaptec_scsi.o
 #driver promise_sata.o
 #driver intel_nic.o
@@ -179,6 +179,7 @@ northbridge amd/amdk8 "mc0"
                                  io 0x60 = 0x60
                                  io 0x62 = 0x64
                                 irq 0x70 = 1
+				irq 0x72 = 12
                         pnp 2e.6 off #  CIR
                         pnp 2e.7 off #  GAME_MIDI_GIPO1
                         pnp 2e.8 off #  GPIO2
diff --git a/src/mainboard/tyan/s2880/mainboard.c b/src/mainboard/tyan/s2880/mainboard.c
index c8521963d8..17ceb5d916 100644
--- a/src/mainboard/tyan/s2880/mainboard.c
+++ b/src/mainboard/tyan/s2880/mainboard.c
@@ -120,7 +120,7 @@ static void onboard_scsi_fixup(void)
 //	print_mem();
 //	amd8111_enable_rom();
 }
-#if 1
+#if 0
 static void vga_fixup(void) {
         // we do this right here because:
         // - all the hardware is working, and some VGA bioses seem to need
@@ -154,8 +154,8 @@ enable(struct chip *chip, enum chip_pass pass)
                 case CONF_PASS_PRE_BOOT:
 			if (conf->fixup_scsi)
         			onboard_scsi_fixup();
-			if (conf->fixup_vga)
-				vga_fixup();
+//			if (conf->fixup_vga)
+//				vga_fixup();
 			printk_debug("mainboard fixup pass %d done\r\n",
 					pass);
 			break;
diff --git a/src/mainboard/tyan/s2881/auto.c b/src/mainboard/tyan/s2881/auto.c
index 5f5069cc97..be11efb4ed 100644
--- a/src/mainboard/tyan/s2881/auto.c
+++ b/src/mainboard/tyan/s2881/auto.c
@@ -113,9 +113,6 @@ static inline int spd_read_byte(unsigned device, unsigned address)
 	return smbus_read_byte(device, address);
 }
 
-/* include mainboard specific ht code */
-#include "hypertransport.c"
-
 #include "northbridge/amd/amdk8/raminit.c"
 #include "northbridge/amd/amdk8/coherent_ht.c"
 #include "sdram/generic_sdram.c"
@@ -166,7 +163,7 @@ static void main(void)
         console_init();
         setup_s2881_resource_map();
         needs_reset = setup_coherent_ht_domain();
-        needs_reset |= ht_setup_chain(PCI_DEV(0, 0x18, 0), 0x80);
+        needs_reset |= ht_setup_chain(PCI_DEV(0, 0x18, 0), 0xc0);
         if (needs_reset) {
                 print_info("ht reset -");
                 soft_reset();
diff --git a/src/mainboard/tyan/s2881/mainboard.c b/src/mainboard/tyan/s2881/mainboard.c
index aa99f64894..3ba458866c 100644
--- a/src/mainboard/tyan/s2881/mainboard.c
+++ b/src/mainboard/tyan/s2881/mainboard.c
@@ -120,7 +120,7 @@ static void onboard_scsi_fixup(void)
 //	print_mem();
 //	amd8111_enable_rom();
 }
-#if 1
+#if 0
 static void vga_fixup(void) {
         // we do this right here because:
         // - all the hardware is working, and some VGA bioses seem to need
@@ -154,8 +154,8 @@ enable(struct chip *chip, enum chip_pass pass)
                 case CONF_PASS_PRE_BOOT:
 			if (conf->fixup_scsi)
         			onboard_scsi_fixup();
-			if (conf->fixup_vga)
-				vga_fixup();
+//			if (conf->fixup_vga)
+//				vga_fixup();
 			printk_debug("mainboard fixup pass %d done\r\n",
 					pass);
 			break;
diff --git a/src/mainboard/tyan/s2882/Config.lb b/src/mainboard/tyan/s2882/Config.lb
index c307568267..c62ea733da 100644
--- a/src/mainboard/tyan/s2882/Config.lb
+++ b/src/mainboard/tyan/s2882/Config.lb
@@ -35,7 +35,7 @@ default LB_CKS_LOC=123
 driver mainboard.o
 #driver adaptec_scsi.o
 #driver si_sata.o
-driver intel_nic.o
+#driver intel_nic.o
 #driver broadcom_nic.o
 #object reset.o
 if HAVE_MP_TABLE object mptable.o end
@@ -196,6 +196,7 @@ northbridge amd/amdk8 "mc0"
                                  io 0x60 = 0x60
                                  io 0x62 = 0x64
                                 irq 0x70 = 1
+				irq 0x72 = 12
                         pnp 2e.6 off #  CIR
                         pnp 2e.7 off #  GAME_MIDI_GIPO1
                         pnp 2e.8 off #  GPIO2
diff --git a/src/mainboard/tyan/s2885/Config.lb b/src/mainboard/tyan/s2885/Config.lb
index c0b61145cb..db6b2f030c 100644
--- a/src/mainboard/tyan/s2885/Config.lb
+++ b/src/mainboard/tyan/s2885/Config.lb
@@ -198,6 +198,7 @@ northbridge amd/amdk8 "mc0"
                                  io 0x60 = 0x60
                                  io 0x62 = 0x64
                                 irq 0x70 = 1
+				irq 0x72 = 12
                         pnp 2e.6 off #  CIR
                         pnp 2e.7 off #  GAME_MIDI_GIPO1
                         pnp 2e.8 off #  GPIO2
diff --git a/src/mainboard/tyan/s2885/auto.c b/src/mainboard/tyan/s2885/auto.c
index 135418bdcb..307331375c 100644
--- a/src/mainboard/tyan/s2885/auto.c
+++ b/src/mainboard/tyan/s2885/auto.c
@@ -29,7 +29,7 @@ static void hard_reset(void)
         set_bios_reset();
 
         /* enable cf9 */
-        pci_write_config8(PCI_DEV(1, 0x04, 3), 0x41, 0xf1);
+        pci_write_config8(PCI_DEV(0, 0x04, 3), 0x41, 0xf1);
         /* reset */
         outb(0x0e, 0x0cf9);
 }
@@ -37,7 +37,7 @@ static void hard_reset(void)
 static void soft_reset(void)
 {
         set_bios_reset();
-        pci_write_config8(PCI_DEV(1, 0x04, 0), 0x47, 1);
+        pci_write_config8(PCI_DEV(0, 0x04, 0), 0x47, 1);
 }
 
 #define REV_B_RESET 0
@@ -114,9 +114,6 @@ static inline int spd_read_byte(unsigned device, unsigned address)
 	return smbus_read_byte(device, address);
 }
 
-/* include mainboard specific ht code */
-#include "hypertransport.c"
-
 #include "northbridge/amd/amdk8/raminit.c"
 #include "northbridge/amd/amdk8/coherent_ht.c"
 #include "sdram/generic_sdram.c"
@@ -167,7 +164,7 @@ static void main(void)
         console_init();
         setup_s2885_resource_map();
         needs_reset = setup_coherent_ht_domain();
-        needs_reset |= ht_setup_chain(PCI_DEV(0, 0x18, 0), 0x80);
+        needs_reset |= ht_setup_chain(PCI_DEV(0, 0x18, 0), 0xc0);
         if (needs_reset) {
                 print_info("ht reset -");
                 soft_reset();
diff --git a/src/mainboard/tyan/s2885/mainboard.c b/src/mainboard/tyan/s2885/mainboard.c
index cd2a9679fa..e142f1b6d7 100644
--- a/src/mainboard/tyan/s2885/mainboard.c
+++ b/src/mainboard/tyan/s2885/mainboard.c
@@ -119,7 +119,7 @@ static void onboard_scsi_fixup(void)
 //	print_mem();
 //	amd8111_enable_rom();
 }
-
+#if 0
 static void vga_fixup(void) {
         // we do this right here because:
         // - all the hardware is working, and some VGA bioses seem to need
@@ -136,6 +136,8 @@ static void vga_fixup(void) {
 #endif
 
 }
+
+#endif
  
 
 static void
@@ -153,8 +155,8 @@ enable(struct chip *chip, enum chip_pass pass)
                 case CONF_PASS_PRE_BOOT:
 			if (conf->fixup_scsi)
         			onboard_scsi_fixup();
-			if (conf->fixup_vga)
-				vga_fixup();
+//			if (conf->fixup_vga)
+//				vga_fixup();
 			printk_debug("mainboard fixup pass %d done\r\n",
 					pass);
 			break;
diff --git a/src/mainboard/tyan/s4880/Config.lb b/src/mainboard/tyan/s4880/Config.lb
index 69e647984f..4f85e44252 100644
--- a/src/mainboard/tyan/s4880/Config.lb
+++ b/src/mainboard/tyan/s4880/Config.lb
@@ -33,9 +33,9 @@ default LB_CKS_RANGE_END=122
 default LB_CKS_LOC=123
 
 driver mainboard.o
-#driver lsi_scsi.o
+driver lsi_scsi.o
 #driver adaptec_scsi.o
-#driver si_sata.o
+driver si_sata.o
 #driver intel_nic.o
 #object reset.o
 if HAVE_MP_TABLE object mptable.o end
diff --git a/src/mainboard/tyan/s4880/auto.c b/src/mainboard/tyan/s4880/auto.c
index 031020323a..8f291f0964 100644
--- a/src/mainboard/tyan/s4880/auto.c
+++ b/src/mainboard/tyan/s4880/auto.c
@@ -28,7 +28,7 @@ static void hard_reset(void)
         set_bios_reset();
 
         /* enable cf9 */
-        pci_write_config8(PCI_DEV(0, 0x04, 3), 0x41, 0xf1);
+        pci_write_config8(PCI_DEV(1, 0x04, 3), 0x41, 0xf1);
         /* reset */
         outb(0x0e, 0x0cf9);
 }
@@ -36,7 +36,7 @@ static void hard_reset(void)
 static void soft_reset(void)
 {
         set_bios_reset();
-        pci_write_config8(PCI_DEV(0, 0x04, 0), 0x47, 1);
+        pci_write_config8(PCI_DEV(1, 0x04, 0), 0x47, 1);
 }
 
 
@@ -121,11 +121,8 @@ static inline int spd_read_byte(unsigned device, unsigned address)
 	return smbus_read_byte(device, address);
 }
 
-/* include mainboard specific ht code */
-#include "hypertransport.c"
-
-
 #include "northbridge/amd/amdk8/raminit.c"
+
 #include "northbridge/amd/amdk8/coherent_ht.c"
 #include "sdram/generic_sdram.c"
 
diff --git a/src/mainboard/tyan/s4882/Config.lb b/src/mainboard/tyan/s4882/Config.lb
new file mode 100644
index 0000000000..ea826238b5
--- /dev/null
+++ b/src/mainboard/tyan/s4882/Config.lb
@@ -0,0 +1,245 @@
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses USE_FALLBACK_IMAGE
+uses LB_CKS_RANGE_START
+uses LB_CKS_RANGE_END
+uses LB_CKS_LOC
+uses MAINBOARD
+uses ARCH
+uses HARD_RESET_BUS
+uses HARD_RESET_DEVICE
+uses HARD_RESET_FUNCTION
+
+#
+#
+###
+### Set all of the defaults for an x86 architecture
+###
+#
+#
+###
+### Build the objects we have code for in this directory.
+###
+##object mainboard.o
+config chip.h
+register "fixup_scsi" = "1" 
+#register "fixup_vga" = "1"
+
+
+##
+## Move the default LinuxBIOS cmos range off of AMD RTC registers
+##
+default LB_CKS_RANGE_START=49
+default LB_CKS_RANGE_END=122
+default LB_CKS_LOC=123
+
+driver mainboard.o
+driver lsi_scsi.o
+#driver adaptec_scsi.o
+driver si_sata.o
+#driver intel_nic.o
+#object reset.o
+if HAVE_MP_TABLE object mptable.o end
+if HAVE_PIRQ_TABLE object irq_tables.o end
+#
+default HARD_RESET_BUS=1
+default HARD_RESET_DEVICE=4
+default HARD_RESET_FUNCTION=0
+#
+arch i386 end
+#cpu k8 end
+#
+###
+### Build our 16 bit and 32 bit linuxBIOS entry code
+###
+mainboardinit cpu/i386/entry16.inc
+mainboardinit cpu/i386/entry32.inc
+mainboardinit cpu/i386/bist32.inc
+ldscript /cpu/i386/entry16.lds
+ldscript /cpu/i386/entry32.lds
+#
+###
+### Build our reset vector (This is where linuxBIOS is entered)
+###
+if USE_FALLBACK_IMAGE 
+	mainboardinit cpu/i386/reset16.inc 
+	ldscript /cpu/i386/reset16.lds 
+else
+	mainboardinit cpu/i386/reset32.inc 
+	ldscript /cpu/i386/reset32.lds 
+end
+#
+#### Should this be in the northbridge code?
+mainboardinit arch/i386/lib/cpu_reset.inc
+#
+###
+### Include an id string (For safe flashing)
+###
+mainboardinit arch/i386/lib/id.inc
+ldscript /arch/i386/lib/id.lds
+#
+####
+#### This is the early phase of linuxBIOS startup 
+#### Things are delicate and we test to see if we should
+#### failover to another image.
+####
+#option MAX_REBOOT_CNT=2
+if USE_FALLBACK_IMAGE
+  ldscript /arch/i386/lib/failover.lds 
+end
+#
+###
+### Setup our mtrrs
+###
+mainboardinit cpu/k8/earlymtrr.inc
+###
+### Only the bootstrap cpu makes it here.
+### Failover if we need to 
+###
+#
+if USE_FALLBACK_IMAGE
+  mainboardinit ./failover.inc
+end
+
+#
+#
+###
+### Setup the serial port
+###
+mainboardinit pc80/serial.inc
+mainboardinit arch/i386/lib/console.inc
+mainboardinit cpu/i386/bist32_fail.inc
+#
+####
+#### O.k. We aren't just an intermediary anymore!
+####
+#
+###
+### Romcc output
+###
+#makerule ./failover.E dep "$(MAINBOARD)/failover.c" act "$(CPP) -I$(TOP)/src $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failever.E"
+#makerule ./failover.inc dep "./romcc ./failover.E" act "./romcc -O ./failover.E > failover.inc"
+#mainboardinit .failover.inc
+
+makerule ./failover.E
+	depends "$(MAINBOARD)/failover.c" 
+	action "$(CPP) -I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/failover.c > ./failover.E"
+end
+
+makerule ./failover.inc
+	depends "./romcc ./failover.E"
+	action "./romcc -O -o failover.inc --label-prefix=failover ./failover.E"end
+
+makerule ./auto.E 
+        depends "$(MAINBOARD)/auto.c option_table.h"
+        action  "$(CPP) -I$(TOP)/src -I. $(ROMCCPPFLAGS) $(CPPFLAGS) $(MAINBOARD)/auto.c > ./auto.E"
+end
+makerule ./auto.inc 
+	depends "./romcc ./auto.E"
+	action "./romcc -O2 -mcpu=k8 -o auto.inc --label-prefix=auto ./auto.E" 
+#	action	"./romcc -mcpu=k8  -O ./auto.E > auto.inc"
+end
+mainboardinit cpu/k8/enable_mmx_sse.inc
+mainboardinit ./auto.inc
+mainboardinit cpu/k8/disable_mmx_sse.inc
+#
+###
+### Include the secondary Configuration files 
+###
+northbridge amd/amdk8 "mc0"
+        pci 0:18.0
+        pci 0:18.0
+        pci 0:18.0
+        pci 0:18.1
+        pci 0:18.2
+        pci 0:18.3
+        southbridge amd/amd8131 "amd8131" link 1
+                pci 0:0.0
+                pci 0:0.1
+                pci 0:1.0
+                pci 0:1.1
+	end
+        southbridge amd/amd8111 "amd8111" link 1
+                pci 0:0.0
+                pci 0:1.0 on
+                pci 0:1.1 on
+                pci 0:1.2 on
+                pci 0:1.3 on
+                pci 0:1.5 off
+                pci 0:1.6 off
+                pci 1:0.0 on
+                pci 1:0.1 on
+                pci 1:0.2 on
+                pci 1:1.0 off
+                superio winbond/w83627hf link 1
+                        pnp 2e.0 off #  Floppy
+                                 io 0x60 = 0x3f0
+                                irq 0x70 = 6
+                                drq 0x74 = 2
+                        pnp 2e.1 off #  Parallel Port
+                                 io 0x60 = 0x378
+                                irq 0x70 = 7
+                        pnp 2e.2 on #  Com1
+                                 io 0x60 = 0x3f8
+                                irq 0x70 = 4
+                        pnp 2e.3 off #  Com2
+                                 io 0x60 = 0x2f8
+                                irq 0x70 = 3
+                        pnp 2e.5 on #  Keyboard
+                                 io 0x60 = 0x60
+                                 io 0x62 = 0x64
+                                irq 0x70 = 1
+                        pnp 2e.6 off #  CIR
+                        pnp 2e.7 off #  GAME_MIDI_GIPO1
+                        pnp 2e.8 off #  GPIO2
+                        pnp 2e.9 off #  GPIO3
+                        pnp 2e.a off #  ACPI
+                        pnp 2e.b off #  HW Monitor
+                end
+        end
+end
+
+northbridge amd/amdk8 "mc1"
+        pci 0:19.0
+        pci 0:19.0
+        pci 0:19.0
+        pci 0:19.1
+        pci 0:19.2
+        pci 0:19.3
+end
+
+northbridge amd/amdk8 "mc2"
+        pci 0:1a.0
+        pci 0:1a.0
+        pci 0:1a.0
+        pci 0:1a.1
+        pci 0:1a.2
+        pci 0:1a.3
+end
+
+
+northbridge amd/amdk8 "mc3"
+        pci 0:1b.0
+        pci 0:1b.0
+        pci 0:1b.0
+        pci 0:1b.1
+        pci 0:1b.2
+        pci 0:1b.3
+end
+
+
+dir /pc80
+#dir /bioscall
+
+cpu k8 "cpu0"
+  register "up" = "{.chip = &amd8131, .ht_width=16, .ht_speed=600}"
+end
+
+cpu k8 "cpu1"
+end
+
+cpu k8 "cpu2"
+end
+
+cpu k8 "cpu3"
+end
diff --git a/src/mainboard/tyan/s4882/VERSION b/src/mainboard/tyan/s4882/VERSION
new file mode 100644
index 0000000000..cd5ac039d6
--- /dev/null
+++ b/src/mainboard/tyan/s4882/VERSION
@@ -0,0 +1 @@
+2.0
diff --git a/src/mainboard/tyan/s4882/auto.c b/src/mainboard/tyan/s4882/auto.c
new file mode 100644
index 0000000000..bbf1df9927
--- /dev/null
+++ b/src/mainboard/tyan/s4882/auto.c
@@ -0,0 +1,277 @@
+#define ASSEMBLY 1
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <arch/smp/lapic.h>
+#include "option_table.h"
+#include "pc80/mc146818rtc_early.c"
+#include "pc80/serial.c"
+#include "arch/i386/lib/console.c"
+#include "ram/ramtest.c"
+#include "northbridge/amd/amdk8/incoherent_ht.c"
+#include "southbridge/amd/amd8111/amd8111_early_smbus.c"
+#include "northbridge/amd/amdk8/raminit.h"
+#include "cpu/k8/apic_timer.c"
+#include "lib/delay.c"
+#include "cpu/p6/boot_cpu.c"
+#include "northbridge/amd/amdk8/reset_test.c"
+#include "northbridge/amd/amdk8/debug.c"
+#include "northbridge/amd/amdk8/cpu_rev.c"
+#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
+
+#define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)
+
+static void hard_reset(void)
+{
+        set_bios_reset();
+
+        /* enable cf9 */
+        pci_write_config8(PCI_DEV(0, 0x04, 3), 0x41, 0xf1);
+        /* reset */
+        outb(0x0e, 0x0cf9);
+}
+
+static void soft_reset(void)
+{
+        set_bios_reset();
+        pci_write_config8(PCI_DEV(0, 0x04, 0), 0x47, 1);
+}
+
+
+#define REV_B_RESET 0
+static void memreset_setup(void)
+{
+#if REV_B_RESET==1
+        outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 16);  //REVC_MEMRST_EN=0
+#else
+        outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 16);  //REVC_MEMRST_EN=1
+#endif
+        outb((0 << 7)|(0 << 6)|(0<<5)|(0<<4)|(1<<2)|(0<<0), SMBUS_IO_BASE + 0xc0 + 17); 
+}
+
+static void memreset(int controllers, const struct mem_controller *ctrl)
+{
+        udelay(800);
+#if REV_B_RESET==1
+        outb((0<<7)|(0<<6)|(0<<5)|(0<<4)|(1<<2)|(1<<0), SMBUS_IO_BASE + 0xc0 + 17); //REVB_MEMRST_L=1
+#endif
+        udelay(90);
+}
+
+static unsigned int generate_row(uint8_t node, uint8_t row, uint8_t maxnodes)
+{
+	/* Routing Table Node i 
+	 *
+	 * F0: 0x40, 0x44, 0x48, 0x4c, 0x50, 0x54, 0x58, 0x5c 
+	 *  i:    0,    1,    2,    3,    4,    5,    6,    7
+	 *
+	 * [ 0: 3] Request Route
+	 *     [0] Route to this node
+	 *     [1] Route to Link 0
+	 *     [2] Route to Link 1
+	 *     [3] Route to Link 2
+	 * [11: 8] Response Route
+	 *     [0] Route to this node
+	 *     [1] Route to Link 0
+	 *     [2] Route to Link 1
+	 *     [3] Route to Link 2
+	 * [19:16] Broadcast route
+	 *     [0] Route to this node
+	 *     [1] Route to Link 0
+	 *     [2] Route to Link 1
+	 *     [3] Route to Link 2
+	 */
+        uint32_t ret=0x00010101; /* default row entry */
+
+
+        static const unsigned int rows_4p[4][4] = {
+                { 0x000b0101, 0x00010202, 0x00030808, 0x00010208 },
+                { 0x00010202, 0x00070101, 0x00010204, 0x00030404 },
+                { 0x00030404, 0x00010204, 0x00070101, 0x00010202 },
+                { 0x00010208, 0x00030808, 0x00010202, 0x000b0101 }
+        };
+        
+        if (!(node>=maxnodes || row>=maxnodes)) {
+		ret=rows_4p[node][row];
+        }
+
+        return ret;
+}
+
+static inline void activate_spd_rom(const struct mem_controller *ctrl)
+{
+#define SMBUS_HUB 0x18
+        unsigned device=(ctrl->channel0[0])>>8;
+        smbus_write_byte(SMBUS_HUB , 0x01, device);
+        smbus_write_byte(SMBUS_HUB , 0x03, 0);
+}
+#if 0
+static inline void change_i2c_mux(unsigned device)
+{
+#define SMBUS_HUB 0x18
+        smbus_write_byte(SMBUS_HUB , 0x01, device);
+        smbus_write_byte(SMBUS_HUB , 0x03, 0);
+}
+#endif
+
+static inline int spd_read_byte(unsigned device, unsigned address)
+{
+	return smbus_read_byte(device, address);
+}
+
+#include "northbridge/amd/amdk8/raminit.c"
+
+#include "northbridge/amd/amdk8/coherent_ht.c"
+#include "sdram/generic_sdram.c"
+
+#include "resourcemap.c" /* tyan does not want the default */
+
+#define FIRST_CPU  1
+#define SECOND_CPU 1
+
+#define THIRD_CPU  1 
+#define FOURTH_CPU 1 
+
+#define TOTAL_CPUS (FIRST_CPU + SECOND_CPU + THIRD_CPU + FOURTH_CPU)
+
+#define RC0 ((1<<1)<<8)
+#define RC1 ((1<<2)<<8)
+#define RC2 ((1<<3)<<8)
+#define RC3 ((1<<4)<<8)
+
+#define DIMM0 0x50
+#define DIMM1 0x51
+#define DIMM2 0x52
+#define DIMM3 0x53
+        
+static void main(void)
+{
+	static const struct mem_controller cpu[] = {
+#if FIRST_CPU
+                {
+                        .node_id = 0,
+                        .f0 = PCI_DEV(0, 0x18, 0),
+                        .f1 = PCI_DEV(0, 0x18, 1),
+                        .f2 = PCI_DEV(0, 0x18, 2),
+                        .f3 = PCI_DEV(0, 0x18, 3),
+                        .channel0 = { RC0|DIMM0, RC0|DIMM2, 0, 0 },
+                        .channel1 = { RC0|DIMM1, RC0|DIMM3, 0, 0 },
+                },
+#endif
+#if SECOND_CPU
+                {
+                        .node_id = 1,
+                        .f0 = PCI_DEV(0, 0x19, 0),
+                        .f1 = PCI_DEV(0, 0x19, 1),
+                        .f2 = PCI_DEV(0, 0x19, 2),
+                        .f3 = PCI_DEV(0, 0x19, 3),
+                        .channel0 = { RC1|DIMM0, RC1|DIMM2 , 0, 0 },
+                        .channel1 = { RC1|DIMM1, RC1|DIMM3 , 0, 0 },
+
+                },
+#endif
+
+#if THIRD_CPU
+                {
+                        .node_id = 2,
+                        .f0 = PCI_DEV(0, 0x1a, 0),
+                        .f1 = PCI_DEV(0, 0x1a, 1),
+                        .f2 = PCI_DEV(0, 0x1a, 2),
+                        .f3 = PCI_DEV(0, 0x1a, 3),
+                        .channel0 = { RC2|DIMM0, RC2|DIMM2, 0, 0 },
+                        .channel1 = { RC2|DIMM1, RC2|DIMM3, 0, 0 },
+
+                },
+#endif
+#if FOURTH_CPU
+                {
+                        .node_id = 3,
+                        .f0 = PCI_DEV(0, 0x1b, 0),
+                        .f1 = PCI_DEV(0, 0x1b, 1),
+                        .f2 = PCI_DEV(0, 0x1b, 2),
+                        .f3 = PCI_DEV(0, 0x1b, 3),
+                        .channel0 = { RC3|DIMM0, RC3|DIMM2, 0, 0 },
+                        .channel1 = { RC3|DIMM1, RC3|DIMM3, 0, 0 },
+
+                },
+#endif
+	};
+	int i;
+        int needs_reset;
+        enable_lapic();
+        init_timer();
+        if (cpu_init_detected()) {
+                asm("jmp __cpu_reset");
+        }
+        distinguish_cpu_resets();
+        if (!boot_cpu()) {
+                stop_this_cpu();
+        }
+        w83627hf_enable_serial(SERIAL_DEV, TTYS0_BASE);
+        uart_init();
+        console_init();
+        setup_s4882_resource_map();
+        needs_reset = setup_coherent_ht_domain();
+        needs_reset |= ht_setup_chain(PCI_DEV(0, 0x18, 0), 0xa0);
+#if 0
+        dump_pci_device(PCI_DEV(0, 4, 0));
+#endif
+        if (needs_reset) {
+                print_info("ht reset -");
+                soft_reset();
+        }
+	
+#if 0
+	dump_pci_devices();
+#endif
+	enable_smbus();
+#if 0
+
+//	activate_spd_rom(&cpu[0]); 
+//	dump_spd_registers(&cpu[0]);
+
+//	for(i=0;i<4;i++) {
+//		activate_spd_rom(&cpu[i]); 
+//        	dump_smbus_registers();
+//	}
+        for(i=1;i<256;i=i*2) {
+                change_i2c_mux(i);
+                dump_smbus_registers();
+        }
+
+#endif
+	memreset_setup();
+	sdram_initialize(sizeof(cpu)/sizeof(cpu[0]), cpu);
+
+#if 0
+	dump_pci_devices();
+#endif
+#if 0
+	dump_pci_device(PCI_DEV(0, 0x18, 1));
+#endif
+
+	/* Check all of memory */
+#if 0
+	msr_t msr;
+	msr = rdmsr(TOP_MEM2);
+	print_debug("TOP_MEM2: ");
+	print_debug_hex32(msr.hi);
+	print_debug_hex32(msr.lo);
+	print_debug("\r\n");
+#endif
+/*
+#if  0
+	ram_check(0x00000000, msr.lo+(msr.hi<<32));
+#else
+#if TOTAL_CPUS < 2
+	// Check 16MB of memory @ 0
+	ram_check(0x00000000, 0x01000000);
+#else
+	// Check 16MB of memory @ 2GB 
+	ram_check(0x80000000, 0x81000000);
+#endif
+#endif
+*/
+}
diff --git a/src/mainboard/tyan/s4882/chip.h b/src/mainboard/tyan/s4882/chip.h
new file mode 100644
index 0000000000..7eb925df36
--- /dev/null
+++ b/src/mainboard/tyan/s4882/chip.h
@@ -0,0 +1,6 @@
+extern struct chip_control mainboard_tyan_s4882_control;
+
+struct mainboard_tyan_s4882_config {
+	int fixup_scsi;
+//	int fixup_vga;
+};
diff --git a/src/mainboard/tyan/s4882/cmos.layout b/src/mainboard/tyan/s4882/cmos.layout
new file mode 100644
index 0000000000..247715e6ac
--- /dev/null
+++ b/src/mainboard/tyan/s4882/cmos.layout
@@ -0,0 +1,96 @@
+entries
+
+#start-bit length  config config-ID    name
+#0            8       r       0        seconds
+#8            8       r       0        alarm_seconds
+#16           8       r       0        minutes
+#24           8       r       0        alarm_minutes
+#32           8       r       0        hours
+#40           8       r       0        alarm_hours
+#48           8       r       0        day_of_week
+#56           8       r       0        day_of_month
+#64           8       r       0        month
+#72           8       r       0        year
+#80           4       r       0        rate_select
+#84           3       r       0        REF_Clock
+#87           1       r       0        UIP
+#88           1       r       0        auto_switch_DST
+#89           1       r       0        24_hour_mode
+#90           1       r       0        binary_values_enable
+#91           1       r       0        square-wave_out_enable
+#92           1       r       0        update_finished_enable
+#93           1       r       0        alarm_interrupt_enable
+#94           1       r       0        periodic_interrupt_enable
+#95           1       r       0        disable_clock_updates
+#96         288       r       0        temporary_filler
+0          384       r       0        reserved_memory
+384          1       e       4        boot_option
+385          1       e       4        last_boot
+386          1       e       1        ECC_memory
+388          4       r       0        reboot_bits
+392          3       e       5        baud_rate
+395          1       e       1        hw_scrubber
+396          1       e       1        interleave_chip_selects
+397          2       e       8        max_mem_clock
+400          1       e       1        power_on_after_fail
+412          4       e       6        debug_level
+416          4       e       7        boot_first
+420          4       e       7        boot_second
+424          4       e       7        boot_third
+428          4       h       0        boot_index
+432	     8       h       0        boot_countdown
+440          4       e       9        slow_cpu
+444          1       e       1        nmi
+728        256       h       0        user_data
+984         16       h       0        check_sum
+# Reserve the extended AMD configuration registers
+1000        24       r       0        reserved_memory
+
+
+
+enumerations
+
+#ID value   text
+1     0     Disable
+1     1     Enable
+2     0     Enable
+2     1     Disable
+4     0     Fallback
+4     1     Normal
+5     0     115200
+5     1     57600
+5     2     38400
+5     3     19200
+5     4     9600
+5     5     4800
+5     6     2400
+5     7     1200
+6     6     Notice
+6     7     Info
+6     8     Debug
+6     9     Spew
+7     0     Network
+7     1     HDD
+7     2     Floppy
+7     8     Fallback_Network
+7     9     Fallback_HDD
+7     10    Fallback_Floppy
+#7     3     ROM
+8     0     200Mhz
+8     1     166Mhz
+8     2     133Mhz
+8     3     100Mhz
+9     0     off
+9     1     87.5%
+9     2     75.0%
+9     3     62.5%
+9     4     50.0%
+9     5     37.5%
+9     6     25.0%
+9     7     12.5%
+
+checksums
+
+checksum 392 983 984
+
+
diff --git a/src/mainboard/tyan/s4882/failover.c b/src/mainboard/tyan/s4882/failover.c
new file mode 100644
index 0000000000..b22abfea06
--- /dev/null
+++ b/src/mainboard/tyan/s4882/failover.c
@@ -0,0 +1,80 @@
+#define ASSEMBLY 1
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <device/pci_ids.h>
+#include <arch/io.h>
+#include <arch/romcc_io.h>
+#include <arch/smp/lapic.h>
+#include "pc80/mc146818rtc_early.c"
+#include "southbridge/amd/amd8111/amd8111_enable_rom.c"
+#include "northbridge/amd/amdk8/early_ht.c"
+#include "cpu/p6/boot_cpu.c"
+#include "northbridge/amd/amdk8/reset_test.c"
+
+#define HAVE_REGPARM_SUPPORT 0
+#if HAVE_REGPARM_SUPPORT
+static unsigned long main(unsigned long bist)
+{
+#else
+static void main(void)
+{
+	unsigned long bist = 0;
+#endif
+	/* Make cerain my local apic is useable */
+	enable_lapic();
+
+	/* Is this a cpu only reset? */
+	if (cpu_init_detected()) {
+		if (last_boot_normal()) {
+			goto normal_image;
+		} else {
+			goto cpu_reset;
+		}
+	}
+	/* Is this a secondary cpu? */
+	if (!boot_cpu()) {
+		if (last_boot_normal()) {
+			goto normal_image;
+		} else {
+			goto fallback_image;
+		}
+	}
+	
+
+	/* Nothing special needs to be done to find bus 0 */
+	/* Allow the HT devices to be found */
+	enumerate_ht_chain();
+	
+	/* Setup the 8111 */
+	amd8111_enable_rom();
+
+	/* Is this a deliberate reset by the bios */
+	if (bios_reset_detected() && last_boot_normal()) {
+		goto normal_image;
+	}
+	/* This is the primary cpu how should I boot? */
+	else if (do_normal_boot()) {
+		goto normal_image;
+	}
+	else {
+		goto fallback_image;
+	}
+ normal_image:
+	asm("jmp __normal_image" 
+		: /* outputs */ 
+		: "a" (bist) /* inputs */
+		: /* clobbers */
+		);
+ cpu_reset:
+	asm("jmp __cpu_reset"
+		: /* outputs */ 
+		: "a"(bist) /* inputs */
+		: /* clobbers */
+		);
+ fallback_image:
+#if HAVE_REGPARM_SUPPORT
+	return bist;
+#else
+	return;
+#endif
+}
diff --git a/src/mainboard/tyan/s4882/irq_tables.c b/src/mainboard/tyan/s4882/irq_tables.c
new file mode 100644
index 0000000000..dd293ca966
--- /dev/null
+++ b/src/mainboard/tyan/s4882/irq_tables.c
@@ -0,0 +1,46 @@
+/* This file was generated by getpir.c, do not modify! 
+   (but if you do, please run checkpir on it to verify)
+   Contains the IRQ Routing Table dumped directly from your memory , wich BIOS sets up
+
+   Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM
+*/
+
+#include <arch/pirq_routing.h>
+
+const struct irq_routing_table intel_irq_routing_table = {
+	PIRQ_SIGNATURE, /* u32 signature */
+	PIRQ_VERSION,   /* u16 version   */
+	32+16*22,        /* there can be total 22 devices on the bus */
+	1,           /* Where the interrupt router lies (bus) */
+	(4<<3)|3,           /* Where the interrupt router lies (dev) */
+	0,         /* IRQs devoted exclusively to PCI usage */
+	0x1022,         /* Vendor */
+	0x7400,         /* Device */
+	0,         /* Crap (miniport) */
+	{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
+	0x9a,         /*  u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+	{
+		{0,0xc0, {{0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{1,(3<<3)|0, {{0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{0x4,0, {{0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0x4, 0xdef8}}, 0, 0},
+		{0x4,0x8, {{0x1, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{0x4,0x20, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0x1, 0},
+		{0x4,0x18, {{0x2, 0xdef8}, {0x1, 0xdef8}, {0x3, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{0x4,0x28, {{0x4, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{0x4,0x30, {{0x3, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{1,(4<<3)|0, {{0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{1,(1<<3)|0, {{0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{0x2,0x18, {{0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}}, 0x2, 0},
+		{0x2,0x10, {{0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}}, 0x3, 0},
+		{0x2,0x48, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{0x2,0x20, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{1,(2<<3)|0, {{0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{0x3,0x18, {{0x1, 0xdef8}, {0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}}, 0x4, 0},
+		{0x3,0x8, {{0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}}, 0x5, 0},
+		{0x3,0x20, {{0x2, 0xdef8}, {0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}}, 0x6, 0},
+		{0x3,0x28, {{0x3, 0xdef8}, {0x4, 0xdef8}, {0x1, 0xdef8}, {0x2, 0xdef8}}, 0x7, 0},
+		{0,0xc8, {{0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{0,0xd0, {{0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+		{0,0xd8, {{0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}, {0, 0xdef8}}, 0, 0},
+	}
+};
diff --git a/src/mainboard/tyan/s4882/mainboard.c b/src/mainboard/tyan/s4882/mainboard.c
new file mode 100644
index 0000000000..32e1a31fd2
--- /dev/null
+++ b/src/mainboard/tyan/s4882/mainboard.c
@@ -0,0 +1,192 @@
+#include <console/console.h>
+#include <device/device.h>
+#include <device/chip.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "../../../northbridge/amd/amdk8/northbridge.h"
+#include "chip.h"
+//#include <part/mainboard.h>
+//#include "lsi_scsi.c"
+unsigned long initial_apicid[CONFIG_MAX_CPUS] =
+{
+	0,1,2,3
+};
+#if 0
+static void fixup_lsi_53c1030(struct device *pdev)
+{
+//	uint8_t byte;
+	uint16_t word;
+
+	byte = 1;
+        pci_write_config8(pdev, 0xff, byte);
+           // Set the device id 
+//      pci_write_config_word(pdev, PCI_DEVICE_ID, PCI_DEVICE_ID_LSILOGIC_53C1030);
+           // Set the subsytem vendor id 
+//      pci_write_config16(pdev, PCI_SUBSYSTEM_VENDOR_ID, PCI_VENDOR_ID_TYAN);  
+        word = 0x10f1;
+	pci_write_config16(pdev, PCI_SUBSYSTEM_VENDOR_ID, word);
+            // Set the subsytem id 
+	word = 0x4882;
+        pci_write_config16(pdev, PCI_SUBSYSTEM_ID, word);
+            // Disable writes to the device id 
+	byte = 0;
+        pci_write_config8(pdev, 0xff, byte);
+
+//	lsi_scsi_init(pdev);
+	
+}
+#endif
+//extern static void lsi_scsi_init(struct device *dev);
+#if 0
+static void print_pci_regs(struct device *dev)
+{
+      uint8_t byte;
+      int i;
+
+      for(i=0;i<256;i++) {
+	     byte = pci_read_config8(dev, i);
+   
+             if((i%16)==0) printk_debug("\n%02x:",i);
+             printk_debug(" %02x",byte);
+      }
+      printk_debug("\n");
+	
+//        pci_write_config8(dev, 0x4, byte);
+
+}
+#endif
+#if 0
+static void print_mem(void)
+{
+        int i;
+	int low_1MB = 0;
+	for(i=low_1MB;i<low_1MB+1024*4;i++) {
+             if((i%16)==0) printk_debug("\n %08x:",i);
+             printk_debug(" %02x ",(unsigned char)*((unsigned char *)i));
+             }
+
+        for(i=low_1MB;i<low_1MB+1024*4;i++) {
+             if((i%16)==0) printk_debug("\n %08x:",i);
+             printk_debug(" %c ",(unsigned char)*((unsigned char *)i));
+             }
+ }
+#endif
+#if 0
+static void amd8111_enable_rom(void)
+{
+        uint8_t byte;
+        struct device *dev;
+
+        /* Enable 4MB rom access at 0xFFC00000 - 0xFFFFFFFF */
+        /* Locate the amd8111 */
+        dev = dev_find_device(0x1022, 0x7468, 0);
+
+        /* Set the 4MB enable bit bit */
+        byte = pci_read_config8(dev, 0x43);
+        byte |= 0x80;
+        pci_write_config8(dev, 0x43, byte);
+}
+#endif
+#if 0
+static void onboard_scsi_fixup(void)
+{
+        struct device *dev;
+#if 0
+	unsigned char i,j,k;
+
+	for(i=0;i<=6;i++) {
+		for(j=0;j<=0x1f;j++) {
+			for (k=0;k<=6;k++){
+				dev = dev_find_slot(i, PCI_DEVFN(j, k));
+				if (dev) {
+			                printk_debug("%02x:%02x:%02x",i,j,k);
+					print_pci_regs(dev);
+        			}
+			}
+		}
+	}
+#endif
+
+
+#if 0
+        dev = dev_find_device(PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_LSI_53C1030,0);
+        if(!dev) {
+                printk_info("LSI_SCSI_FW_FIXUP: No Device Found!");
+                return;
+        }
+
+	lsi_scsi_init(dev); 
+#endif
+//	print_mem();
+//	amd8111_enable_rom();
+}
+#endif
+#if 0
+static void vga_fixup(void) {
+        // we do this right here because:
+        // - all the hardware is working, and some VGA bioses seem to need
+        //   that
+        // - we need page 0 below for linuxbios tables.
+#if CONFIG_REALMODE_IDT == 1
+        printk_debug("INSTALL REAL-MODE IDT\n");
+        setup_realmode_idt();
+#endif
+#if CONFIG_VGABIOS == 1
+        printk_debug("DO THE VGA BIOS\n");
+        do_vgabios();
+        post_code(0x93);
+#endif
+
+}
+#endif 
+
+static void
+enable(struct chip *chip, enum chip_pass pass)
+{
+
+        struct mainboard_tyan_s4882_config *conf = 
+		(struct mainboard_tyan_s4882_config *)chip->chip_info;
+
+        switch (pass) {
+		default: break;
+//		case CONF_PASS_PRE_CONSOLE:
+//		case CONF_PASS_PRE_PCI:
+//		case CONF_PASS_POST_PCI:		
+                case CONF_PASS_PRE_BOOT:
+//			if (conf->fixup_scsi)
+//        			onboard_scsi_fixup();
+//			if (conf->fixup_vga)
+//				vga_fixup();
+			printk_debug("mainboard fixup pass %d done\r\n",
+					pass);
+			break;
+	}
+
+}
+static struct device_operations mainboard_operations = {
+        .read_resources   = root_dev_read_resources,
+        .set_resources    = root_dev_set_resources,
+        .enable_resources = enable_childrens_resources,
+        .init             = 0,
+        .scan_bus         = amdk8_scan_root_bus,
+        .enable           = 0,
+};
+
+static void enumerate(struct chip *chip)
+{
+        struct chip *child;
+        dev_root.ops = &mainboard_operations;
+        chip->dev = &dev_root;
+        chip->bus = 0;
+        for(child = chip->children; child; child = child->next) {
+                child->bus = &dev_root.link[0];
+        }
+}
+struct chip_control mainboard_tyan_s4882_control = {
+        .enable = enable,
+        .enumerate = enumerate,
+        .name      = "Tyan s4882 mainboard ",
+};
+
+
diff --git a/src/mainboard/tyan/s4882/mptable.c b/src/mainboard/tyan/s4882/mptable.c
new file mode 100644
index 0000000000..a95680e512
--- /dev/null
+++ b/src/mainboard/tyan/s4882/mptable.c
@@ -0,0 +1,198 @@
+#include <console/console.h>
+#include <arch/smp/mpspec.h>
+#include <device/pci.h>
+#include <string.h>
+#include <stdint.h>
+
+void *smp_write_config_table(void *v, unsigned long * processor_map)
+{
+        static const char sig[4] = "PCMP";
+        static const char oem[8] = "TYAN    ";
+        static const char productid[12] = "S48822       ";
+        struct mp_config_table *mc;
+
+        unsigned char bus_num;
+        unsigned char bus_isa;
+        unsigned char bus_8131_1;
+        unsigned char bus_8131_2;
+        unsigned char bus_8111_1;
+  
+        mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN);
+        memset(mc, 0, sizeof(*mc));
+
+        memcpy(mc->mpc_signature, sig, sizeof(sig));
+        mc->mpc_length = sizeof(*mc); /* initially just the header */
+        mc->mpc_spec = 0x04;
+        mc->mpc_checksum = 0; /* not yet computed */
+        memcpy(mc->mpc_oem, oem, sizeof(oem));
+        memcpy(mc->mpc_productid, productid, sizeof(productid));
+        mc->mpc_oemptr = 0;
+        mc->mpc_oemsize = 0;
+        mc->mpc_entry_count = 0; /* No entries yet... */
+        mc->mpc_lapic = LAPIC_ADDR;
+        mc->mpe_length = 0;
+        mc->mpe_checksum = 0;
+        mc->reserved = 0;
+
+        smp_write_processors(mc, processor_map);
+
+       
+        {
+                device_t dev;
+                
+                /* 8111 */
+                dev = dev_find_slot(1, PCI_DEVFN(0x03,0));
+                if (dev) {
+                        bus_8111_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
+                        bus_isa    = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
+                        bus_isa++; 
+                }       
+                else {
+                        printk_debug("ERROR - could not find PCI 1:03.0, using defaults\n");
+
+                        bus_8111_1 = 4;
+                        bus_isa = 5;
+                }
+                /* 8131-1 */
+                dev = dev_find_slot(1, PCI_DEVFN(0x01,0));
+                if (dev) {
+                        bus_8131_1 = pci_read_config8(dev, PCI_SECONDARY_BUS);
+
+                }
+                else {
+                        printk_debug("ERROR - could not find PCI 1:01.0, using defaults\n");
+
+                        bus_8131_1 = 2;
+                }
+                /* 8131-2 */
+                dev = dev_find_slot(1, PCI_DEVFN(0x02,0));
+                if (dev) {
+                        bus_8131_2 = pci_read_config8(dev, PCI_SECONDARY_BUS);
+
+                }
+                else {
+                        printk_debug("ERROR - could not find PCI 1:02.0, using defaults\n");
+
+                        bus_8131_2 = 3;
+                }
+        }
+
+/*Bus:          Bus ID  Type*/
+        /* define bus and isa numbers */
+        for(bus_num = 0; bus_num < bus_isa; bus_num++) {
+                smp_write_bus(mc, bus_num, "PCI   ");
+        }
+        smp_write_bus(mc, bus_isa, "ISA   ");
+
+	
+/*I/O APICs:	APIC ID	Version	State		Address*/
+	smp_write_ioapic(mc, 4, 0x11, 0xfec00000);
+        {
+                struct pci_dev *dev;
+                uint32_t base;
+                dev = dev_find_slot(1, PCI_DEVFN(0x1,1));
+                if (dev) {
+                        base = pci_read_config32(dev, PCI_BASE_ADDRESS_0);
+                        base &= PCI_BASE_ADDRESS_MEM_MASK;
+                        smp_write_ioapic(mc, 5, 0x11, base);
+                }
+                dev = dev_find_slot(1, PCI_DEVFN(0x2,1));
+                if (dev) {
+                        base = pci_read_config32(dev, PCI_BASE_ADDRESS_0);
+                        base &= PCI_BASE_ADDRESS_MEM_MASK;
+                        smp_write_ioapic(mc, 6, 0x11, base);
+                }
+	}
+  
+/*I/O Ints:	Type	Polarity    Trigger	Bus ID	 IRQ	APIC ID	PIN#
+*/	smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, 0x4, 0x0);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x1, 0x4, 0x1);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, 0x4, 0x2);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x3, 0x4, 0x3);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x4, 0x4, 0x4);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x5, 0x4, 0x5);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x6, 0x4, 0x6);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x7, 0x4, 0x7);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x8, 0x4, 0x8);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x9, 0x4, 0x9);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xa, 0x4, 0xa);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xb, 0x4, 0xb);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xc, 0x4, 0xc);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xd, 0x4, 0xd);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xe, 0x4, 0xe);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xf, 0x4, 0xf);
+	
+
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 1, (4<<2)|0, 0x4, 0x13);
+
+
+//On Board AMD USB
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (0<<2)|3, 0x4, 0x13);
+
+//On Board Via USB 1.1 and 2
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (3<<2)|0, 0x4, 0x11); //1.1
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (3<<2)|1, 0x4, 0x12); //1.1
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (3<<2)|2, 0x4, 0x10); //2
+
+//Slot 5 PCI 32
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (4<<2)|0, 0x4, 0x10);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (4<<2)|1, 0x4, 0x11);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (4<<2)|2, 0x4, 0x12); //
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (4<<2)|3, 0x4, 0x13); //
+
+
+//On Board SI Serial ATA
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (5<<2)|0, 0x4, 0x13);
+//On Board ATI Display Adapter
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8111_1, (6<<2)|0, 0x4, 0x12);
+
+
+//Slot 4 PCIX 100/66
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (3<<2)|0, 0x5, 0x3);
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (3<<2)|1, 0x5, 0x0);
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (3<<2)|2, 0x5, 0x1);//
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (3<<2)|3, 0x5, 0x2);//
+
+//Slot 3 PCIX 100/66        
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (2<<2)|0, 0x5, 0x2);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (2<<2)|1, 0x5, 0x3);//
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (2<<2)|2, 0x5, 0x0);//
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (2<<2)|3, 0x5, 0x1);//
+
+//On Board LSI scsi and NIC
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (4<<2)|0, 0x5, 0x0);
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (4<<2)|1, 0x5, 0x1);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (9<<2)|0, 0x5, 0x0);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_1, (9<<2)|1, 0x5, 0x1);
+
+//Slot 2 PCI-X 133/100/66
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (3<<2)|0, 0x6, 0x0);
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (3<<2)|1, 0x6, 0x1);
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (3<<2)|2, 0x6, 0x2); //
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (3<<2)|3, 0x6, 0x3); //
+
+//Slot 1 PCI-X 133/100/66
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (1<<2)|0, 0x6, 0x1);
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (1<<2)|1, 0x6, 0x2);
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (1<<2)|2, 0x6, 0x3);//
+        smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_8131_2, (1<<2)|3, 0x6, 0x0);//
+
+/*Local Ints:	Type	Polarity    Trigger	Bus ID	 IRQ	APIC ID	PIN#*/
+	smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x0);
+	smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x1);
+	/* There is no extension information... */
+
+	/* Compute the checksums */
+	mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length);
+	mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length);
+	printk_debug("Wrote the mp table end at: %p - %p\n",
+		mc, smp_next_mpe_entry(mc));
+	return smp_next_mpe_entry(mc);
+}
+
+unsigned long write_smp_table(unsigned long addr, unsigned long *processor_map)
+{
+	void *v;
+	v = smp_write_floating_table(addr);
+	return (unsigned long)smp_write_config_table(v, processor_map);
+}
diff --git a/src/mainboard/tyan/s4882/resourcemap.c b/src/mainboard/tyan/s4882/resourcemap.c
new file mode 100644
index 0000000000..423ac3cf00
--- /dev/null
+++ b/src/mainboard/tyan/s4882/resourcemap.c
@@ -0,0 +1,264 @@
+/*
+ * Tyan S4882 needs a different resource map
+ *
+ */
+
+static void setup_s4882_resource_map(void)
+{
+	static const unsigned int register_values[] = {
+	/* Careful set limit registers before base registers which contain the enables */
+	/* DRAM Limit i Registers
+	 * F1:0x44 i = 0
+	 * F1:0x4C i = 1
+	 * F1:0x54 i = 2
+	 * F1:0x5C i = 3
+	 * F1:0x64 i = 4
+	 * F1:0x6C i = 5
+	 * F1:0x74 i = 6
+	 * F1:0x7C i = 7
+	 * [ 2: 0] Destination Node ID
+	 *	   000 = Node 0
+	 *	   001 = Node 1
+	 *	   010 = Node 2
+	 *	   011 = Node 3
+	 *	   100 = Node 4
+	 *	   101 = Node 5
+	 *	   110 = Node 6
+	 *	   111 = Node 7
+	 * [ 7: 3] Reserved
+	 * [10: 8] Interleave select
+	 *	   specifies the values of A[14:12] to use with interleave enable.
+	 * [15:11] Reserved
+	 * [31:16] DRAM Limit Address i Bits 39-24
+	 *	   This field defines the upper address bits of a 40 bit  address
+	 *	   that define the end of the DRAM region.
+	 */
+	PCI_ADDR(0, 0x18, 1, 0x44), 0x0000f8f8, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x4C), 0x0000f8f8, 0x00000001,
+	PCI_ADDR(0, 0x18, 1, 0x54), 0x0000f8f8, 0x00000002,
+	PCI_ADDR(0, 0x18, 1, 0x5C), 0x0000f8f8, 0x00000003,
+	PCI_ADDR(0, 0x18, 1, 0x64), 0x0000f8f8, 0x00000004,
+	PCI_ADDR(0, 0x18, 1, 0x6C), 0x0000f8f8, 0x00000005,
+	PCI_ADDR(0, 0x18, 1, 0x74), 0x0000f8f8, 0x00000006,
+	PCI_ADDR(0, 0x18, 1, 0x7C), 0x0000f8f8, 0x00000007,
+	/* DRAM Base i Registers
+	 * F1:0x40 i = 0
+	 * F1:0x48 i = 1
+	 * F1:0x50 i = 2
+	 * F1:0x58 i = 3
+	 * F1:0x60 i = 4
+	 * F1:0x68 i = 5
+	 * F1:0x70 i = 6
+	 * F1:0x78 i = 7
+	 * [ 0: 0] Read Enable
+	 *	   0 = Reads Disabled
+	 *	   1 = Reads Enabled
+	 * [ 1: 1] Write Enable
+	 *	   0 = Writes Disabled
+	 *	   1 = Writes Enabled
+	 * [ 7: 2] Reserved
+	 * [10: 8] Interleave Enable
+	 *	   000 = No interleave
+	 *	   001 = Interleave on A[12] (2 nodes)
+	 *	   010 = reserved
+	 *	   011 = Interleave on A[12] and A[14] (4 nodes)
+	 *	   100 = reserved
+	 *	   101 = reserved
+	 *	   110 = reserved
+	 *	   111 = Interleve on A[12] and A[13] and A[14] (8 nodes)
+	 * [15:11] Reserved
+	 * [13:16] DRAM Base Address i Bits 39-24
+	 *	   This field defines the upper address bits of a 40-bit address
+	 *	   that define the start of the DRAM region.
+	 */
+	PCI_ADDR(0, 0x18, 1, 0x40), 0x0000f8fc, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x48), 0x0000f8fc, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x50), 0x0000f8fc, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x58), 0x0000f8fc, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x60), 0x0000f8fc, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x68), 0x0000f8fc, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x70), 0x0000f8fc, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x78), 0x0000f8fc, 0x00000000,
+
+	/* Memory-Mapped I/O Limit i Registers
+	 * F1:0x84 i = 0
+	 * F1:0x8C i = 1
+	 * F1:0x94 i = 2
+	 * F1:0x9C i = 3
+	 * F1:0xA4 i = 4
+	 * F1:0xAC i = 5
+	 * F1:0xB4 i = 6
+	 * F1:0xBC i = 7
+	 * [ 2: 0] Destination Node ID
+	 *	   000 = Node 0
+	 *	   001 = Node 1
+	 *	   010 = Node 2
+	 *	   011 = Node 3
+	 *	   100 = Node 4
+	 *	   101 = Node 5
+	 *	   110 = Node 6
+	 *	   111 = Node 7
+	 * [ 3: 3] Reserved
+	 * [ 5: 4] Destination Link ID
+	 *	   00 = Link 0
+	 *	   01 = Link 1
+	 *	   10 = Link 2
+	 *	   11 = Reserved
+	 * [ 6: 6] Reserved
+	 * [ 7: 7] Non-Posted
+	 *	   0 = CPU writes may be posted
+	 *	   1 = CPU writes must be non-posted
+	 * [31: 8] Memory-Mapped I/O Limit Address i (39-16)
+	 *	   This field defines the upp adddress bits of a 40-bit address that
+	 *	   defines the end of a memory-mapped I/O region n
+	 */
+	PCI_ADDR(0, 0x18, 1, 0x84), 0x00000048, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x8C), 0x00000048, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x94), 0x00000048, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x9C), 0x00000048, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xA4), 0x00000048, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xAC), 0x00000048, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xB4), 0x00000048, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xBC), 0x00000048, 0x00ffff10,
+
+	/* Memory-Mapped I/O Base i Registers
+	 * F1:0x80 i = 0
+	 * F1:0x88 i = 1
+	 * F1:0x90 i = 2
+	 * F1:0x98 i = 3
+	 * F1:0xA0 i = 4
+	 * F1:0xA8 i = 5
+	 * F1:0xB0 i = 6
+	 * F1:0xB8 i = 7
+	 * [ 0: 0] Read Enable
+	 *	   0 = Reads disabled
+	 *	   1 = Reads Enabled
+	 * [ 1: 1] Write Enable
+	 *	   0 = Writes disabled
+	 *	   1 = Writes Enabled
+	 * [ 2: 2] Cpu Disable
+	 *	   0 = Cpu can use this I/O range
+	 *	   1 = Cpu requests do not use this I/O range
+	 * [ 3: 3] Lock
+	 *	   0 = base/limit registers i are read/write
+	 *	   1 = base/limit registers i are read-only
+	 * [ 7: 4] Reserved
+	 * [31: 8] Memory-Mapped I/O Base Address i (39-16)
+	 *	   This field defines the upper address bits of a 40bit address 
+	 *	   that defines the start of memory-mapped I/O region i
+	 */
+	PCI_ADDR(0, 0x18, 1, 0x80), 0x000000f0, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x88), 0x000000f0, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x90), 0x000000f0, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0x98), 0x000000f0, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xA0), 0x000000f0, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xA8), 0x000000f0, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xB0), 0x000000f0, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xB8), 0x000000f0, 0x00fc0003,
+
+	/* PCI I/O Limit i Registers
+	 * F1:0xC4 i = 0
+	 * F1:0xCC i = 1
+	 * F1:0xD4 i = 2
+	 * F1:0xDC i = 3
+	 * [ 2: 0] Destination Node ID
+	 *	   000 = Node 0
+	 *	   001 = Node 1
+	 *	   010 = Node 2
+	 *	   011 = Node 3
+	 *	   100 = Node 4
+	 *	   101 = Node 5
+	 *	   110 = Node 6
+	 *	   111 = Node 7
+	 * [ 3: 3] Reserved
+	 * [ 5: 4] Destination Link ID
+	 *	   00 = Link 0
+	 *	   01 = Link 1
+	 *	   10 = Link 2
+	 *	   11 = reserved
+	 * [11: 6] Reserved
+	 * [24:12] PCI I/O Limit Address i
+	 *	   This field defines the end of PCI I/O region n
+	 * [31:25] Reserved
+	 */
+	PCI_ADDR(0, 0x18, 1, 0xC4), 0xFE000FC8, 0x01fff010,
+	PCI_ADDR(0, 0x18, 1, 0xCC), 0xFE000FC8, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xD4), 0xFE000FC8, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xDC), 0xFE000FC8, 0x00000000,
+
+	/* PCI I/O Base i Registers
+	 * F1:0xC0 i = 0
+	 * F1:0xC8 i = 1
+	 * F1:0xD0 i = 2
+	 * F1:0xD8 i = 3
+	 * [ 0: 0] Read Enable
+	 *	   0 = Reads Disabled
+	 *	   1 = Reads Enabled
+	 * [ 1: 1] Write Enable
+	 *	   0 = Writes Disabled
+	 *	   1 = Writes Enabled
+	 * [ 3: 2] Reserved
+	 * [ 4: 4] VGA Enable
+	 *	   0 = VGA matches Disabled
+	 *	   1 = matches all address < 64K and where A[9:0] is in the 
+	 *	       range 3B0-3BB or 3C0-3DF independen of the base & limit registers
+	 * [ 5: 5] ISA Enable
+	 *	   0 = ISA matches Disabled
+	 *	   1 = Blocks address < 64K and in the last 768 bytes of eack 1K block
+	 *	       from matching agains this base/limit pair
+	 * [11: 6] Reserved
+	 * [24:12] PCI I/O Base i
+	 *	   This field defines the start of PCI I/O region n 
+	 * [31:25] Reserved
+	 */
+	PCI_ADDR(0, 0x18, 1, 0xC0), 0xFE000FCC, 0x00000003,
+	PCI_ADDR(0, 0x18, 1, 0xC8), 0xFE000FCC, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xD0), 0xFE000FCC, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xD8), 0xFE000FCC, 0x00000000,
+
+	/* Config Base and Limit i Registers
+	 * F1:0xE0 i = 0
+	 * F1:0xE4 i = 1
+	 * F1:0xE8 i = 2
+	 * F1:0xEC i = 3
+	 * [ 0: 0] Read Enable
+	 *	   0 = Reads Disabled
+	 *	   1 = Reads Enabled
+	 * [ 1: 1] Write Enable
+	 *	   0 = Writes Disabled
+	 *	   1 = Writes Enabled
+	 * [ 2: 2] Device Number Compare Enable
+	 *	   0 = The ranges are based on bus number
+	 *	   1 = The ranges are ranges of devices on bus 0
+	 * [ 3: 3] Reserved
+	 * [ 6: 4] Destination Node
+	 *	   000 = Node 0
+	 *	   001 = Node 1
+	 *	   010 = Node 2
+	 *	   011 = Node 3
+	 *	   100 = Node 4
+	 *	   101 = Node 5
+	 *	   110 = Node 6
+	 *	   111 = Node 7
+	 * [ 7: 7] Reserved
+	 * [ 9: 8] Destination Link
+	 *	   00 = Link 0
+	 *	   01 = Link 1
+	 *	   10 = Link 2
+	 *	   11 - Reserved
+	 * [15:10] Reserved
+	 * [23:16] Bus Number Base i
+	 *	   This field defines the lowest bus number in configuration region i
+	 * [31:24] Bus Number Limit i
+	 *	   This field defines the highest bus number in configuration regin i
+	 */
+	PCI_ADDR(0, 0x18, 1, 0xE0), 0x0000FC88, 0xff000103,
+	PCI_ADDR(0, 0x18, 1, 0xE4), 0x0000FC88, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xE8), 0x0000FC88, 0x00000000,
+	PCI_ADDR(0, 0x18, 1, 0xEC), 0x0000FC88, 0x00000000,
+	};
+	int max;
+	max = sizeof(register_values)/sizeof(register_values[0]);
+	setup_resource_map(register_values, max);
+}
+