| Age | Commit message (Collapse) | Author |
|---|
|
For some reason, the Asmedia 118x PCIe switch needs a little help to
make sure that the downstream links train at Gen2 speed. So add a
PCI I/O protocol notifier that implements this for each PCIe downstream
port that is present on the system.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
In order to be able to use UART #0 on the DeveloperBox's 96boards low
speed connector, expose it to the OS by adding a node to the device
tree. This requires a CM3 firmware build that makes the SCP detach
from the serial port after boot.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Masahisa KOJIMA <kojima.masahisa@socionext.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
The EVB does not boot if PCI RC #0 has no card inserted, and will hang in
the PCIe initialization code. So let's check the presence detect GPIO,
and only enable PCI RC #0 if it is asserted.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
If a PCIe RC is not enabled (due to the fact that the slot is not
populated), set its DT node 'status' property to 'disabled' so that
the OS will not attempt to attach to it.
This means we will need to switch from the default DtPlatformDtbLoaderLib
to a special one for our platform.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
In order to accommodate the EVB, whose PCIe RC #0 should not be touched
by software if no card is inserted, add a PCD that tells the PCIe driver
code which RCs should be initialized and exposed to the PCI host bridge
driver.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Attempt to adhere more closely to the PCIe spec by ensuring that PERST#
remains asserted for at least 100 ms. Give it a good margin, and delay
for 150 ms; the additional boot time delay is not going to be noticeable
by anyone anyway.
Add some missing barriers as well, so that the reset takes effect right
when we think it does.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
It appears that whatever was preventing us from using CPU idle with
PSCI low power states has disappeared, so let's enable the low power
states in the DT.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Commit ce95ec196da0 ("Silicon/SynQuacer: enable coherent DMA for NETSEC
and eMMC") introduced a call to MmioOr32 into PlatformDxe without adding
the appropriate #include and LibraryClass references, resulting in build
failures when attempting to build the SynQuacer platforms. So add them.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
As it turns out, it is surprisingly easy to configure both the NETSEC
and eMMC devices as cache coherent for DMA, given that they are both
behind the same SMMU which is already configured in passthrough mode
by the firmware running on the SCP.
So update the static SMMU configuration to make memory accesses performed
by these devices inner shareable inner/outer writeback cacheable, which
makes them cache coherent with the CPUs.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
The I2C driver prints a warning under DEBUG when a I2C transaction times
out. This will occur on the rev 0.1 DeveloperBox boards due to a board
level error in the I2C routing (unless the MCU has been lifted off the
bus).
Currently, this will trigger a crash due to a missing __FUNCTION__
argument to a %a specifier in a DEBUG string, because instead, the code
will attempt to dereference a EFI_STATUS variable as a char pointer.
So add the missing __FUNCTION__ argument.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Now that we incorporated NorFlashInfoLib into the Fip006Dxe driver,
replace the code that explicitly enables flag status register polling
for Micron NOR flash with a test of the flags field provided by
NorFlashInfoLib, which carries the same information.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Pipat Methavanitpong <methavanitpong.pipat@socionext.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
As it turns out, getting the PCIe controllers to switch to Gen2 speed
is surprisingly easy. It only involves setting the 'speed change' bit
in the controller at initialization time, after which the hardware
will automatically attempt to switch to Gen2 speed after training at
Gen1 speed has completed.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Fix the weird indentation in the various #defines in the file containing
the RC init code. This is a whitespace only change.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
The function ArmPlatformInitializeSystemMemory () has been removed from
ArmPlatformLib, so remove all the [empty] implementations provided by
the various platforms.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Add the drivers, library resolutions and PCD settings to enable RTC
support on DeveloperBox. Also, update PlatformDxe to register the
non-discoverable device handles for both I2C controllers.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Add a driver that produces the I2C master protocol on top of the I2C
controllers that are implemented in the SynQuacer Socionext SoC. Note
that this supports two modes simultaneously: I2C controllers that are
only usable at boot time, and usable via the I2C protocol stack, and
I2C controllers that are dedicated for the RTC or other runtime
components.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Describe the SynQuacer SoC's eMMC controller in DT so the OS can
attach to it.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Ordinary computers typically have a physical switch or jumper on the
board that allows non-volatile settings to be cleared. Let's implement
the same using DIP switch #1 on block #3, and clear the EFI variable
store if it is set to ON at boot time.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
In order to be able to sample the state of the DIP switches at early
boot on the Developer Box platform, implement the GPIO PPI based on
the GPIO block that is implemented in the SynQuacer SoC.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
In preparation of adding support for setting a DIP switch to clear the
EFI variable store, update the early capsule handling logic to take the
boot mode into account.
This is necessary for two reasons:
- we override the boot mode when a capsule is detected,
- the capsule detection itself involves reading a EFI variable, which we
shouldn't be doing if the varstore may be in a bad state.
So factor out the initial capsule check (to keep the code understandable)
and only perform it if we are not booting in 'clear NVRAM' mode.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Add the power button as a gpio-keys KEY_POWER button, and mark it as
a wakeup source so it can be used under the OS both as a 'sleep' and
as a 'wake' button.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
Add a DT node for the external interrupt unit (EXIU), which handles
interrupts from GPIO lines. We need OS support for this for things
like PHY interrupts and a 'wake' button.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Add a description of the SoCs GPIO controller as well as a description
of DIP switch block #3, which is wired to GPIOs 0 - 7, both on the
evaluation board as well as the Developer Box.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
This adds support for the first working sample of the MZSC2AM board,
revision 0.1
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Implement workaround suggested by Socionext to get legacy endpoints
with 32-bit BARs working. This fixes the issue on Developer Box with
the onboard ASM1061 SATA controller.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Add support for dealing with capsules left in memory by the OS before
reboot. This needs to be done early, before the memory is reused, which
is why the initial handling must reside here.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
In order to support capsule update, implement PlatformFlashAccessLib that
exposes write access to the UEFI NOR partition.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Wire up the non-volatile EFI variable store support, by switching from
the emulation driver to the real one, and enabling the prerequisite
FTW and NOR flash drivers.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
This imports the driver sources provided by Socionext for the FIP006
SPI NOR flash device found on SynQuacer SoCs. It has been slightly
tweaked to bring it up to date with the changes made on the EDK2 side
since it was forked.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Pipat Methavanitpong <methavanitpong.pipat@socionext.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Add the platform glue for the NOR flash driver.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Add a device tree description of the SynQuacer SoC, and expose it for
the SynQuacerEvalBoard platforms. This includes the menu option in the
UEFI boot menu to switch between ACPI and DT.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
The SynQuacer SOC has two separate PCIe RCs, which means there is
no single value for the translation offset between I/O port accesses
and MMIO accesses. So add a special implementation of EFI_CPU_IO2_PROTOCOL
that takes the two disjoint I/O windows into account.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Implement the glue library that exposes the PCIe root complexes to
the generic PCI host bridge driver. Since that driver is the first
one to access the PCI config space, put the low level init code for
the RCs into this library's constructor.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Having two distinct root complexes is not supported by the standard
set of PciLib/PciExpressLib/PciSegmentLib, so let's reimplement one
of the latter specifically for this platform (and forget about the
others).
This also allows us to implement the Synopsys Designware PCIe specific
workaround for PCI config space accesses to devices 1 and up on bus 0.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
This is a barebones port based on the .DSC/.FDF and ArmPlatformLib
code provided by Socionext. It can boot into the UiApp menu screen
or the UEFI Shell, but lacks support for any peripherals.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Implement MemoryInitPeiLib based on the newly added DramInfo
PPI, which retrieves the DRAM information from lower level
firmware.
Note that the firmware volumes in SPI NOR are mapped with
different attributes: the FV containing the PEI modules that
may execute in place is mapped as uncached memory, given that
it requires executable permissions. The FV containing the
compressed DXE modules is mapped with device attributes for
performance (!), and copied into DRAM by the platform PEIM
once permanent memory is installed.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
This implements a driver that will take care of platform specific
initialization, such as declaring non-discoverable devices, and
installing the device tree blob as a configuration table.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Create a specialized PlatformPeiLib implementation that invokes the
platform specific firmware interface (currently, just a data structure
left in SRAM) to set the ARM standard PcdSystemMemoryBase|Size PCDs,
and expose the information via a newly added DramInfo PPI.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
This adds the NetSecDxe driver provided by Socionext, but reworked
extensively to improve compliance with the SimpleNetworkProtocol API,
and to avoid uncached allocations for streaming DMA.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
|
Add a package .DEC description for SynQuacer with an [Includes]
section, and add header files containing descriptions of the
platform's memory map and PCIe configuration. No code yet.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
|
