blob: a9ff2e9eb5c43489c4750bb5ad12a8c6ac28827a (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
|
/** @file
*
* Copyright (c) 2011, ARM Limited. All rights reserved.
*
* This program and the accompanying materials
* are licensed and made available under the terms and conditions of the BSD License
* which accompanies this distribution. The full text of the license may be found at
* http://opensource.org/licenses/bsd-license.php
*
* THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
* WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
*
**/
#ifndef __PL011_UART_H__
#define __PL011_UART_H__
// PL011 Registers
#define UARTDR 0x000
#define UARTRSR 0x004
#define UARTECR 0x004
#define UARTFR 0x018
#define UARTILPR 0x020
#define UARTIBRD 0x024
#define UARTFBRD 0x028
#define UARTLCR_H 0x02C
#define UARTCR 0x030
#define UARTIFLS 0x034
#define UARTIMSC 0x038
#define UARTRIS 0x03C
#define UARTMIS 0x040
#define UARTICR 0x044
#define UARTDMACR 0x048
#define UART_115200_IDIV 13 // Integer Part
#define UART_115200_FDIV 1 // Fractional Part
#define UART_38400_IDIV 39
#define UART_38400_FDIV 5
#define UART_19200_IDIV 12
#define UART_19200_FDIV 37
// Data status bits
#define UART_DATA_ERROR_MASK 0x0F00
// Status reg bits
#define UART_STATUS_ERROR_MASK 0x0F
// Flag reg bits
#define UART_TX_EMPTY_FLAG_MASK 0x80
#define UART_RX_FULL_FLAG_MASK 0x40
#define UART_TX_FULL_FLAG_MASK 0x20
#define UART_RX_EMPTY_FLAG_MASK 0x10
#define UART_BUSY_FLAG_MASK 0x08
// Control reg bits
#define PL011_UARTCR_CTSEN (1 << 15) // CTS hardware flow control enable
#define PL011_UARTCR_RTSEN (1 << 14) // RTS hardware flow control enable
#define PL011_UARTCR_RTS (1 << 11) // Request to send
#define PL011_UARTCR_DTR (1 << 10) // Data transmit ready.
#define PL011_UARTCR_RXE (1 << 9) // Receive enable
#define PL011_UARTCR_TXE (1 << 8) // Transmit enable
#define PL011_UARTCR_UARTEN (1 << 0) // UART Enable
// Line Control Register Bits
#define PL011_UARTLCR_H_SPS (1 << 7) // Stick parity select
#define PL011_UARTLCR_H_WLEN_8 (3 << 5)
#define PL011_UARTLCR_H_WLEN_7 (2 << 5)
#define PL011_UARTLCR_H_WLEN_6 (1 << 5)
#define PL011_UARTLCR_H_WLEN_5 (0 << 5)
#define PL011_UARTLCR_H_FEN (1 << 4) // FIFOs Enable
#define PL011_UARTLCR_H_STP2 (1 << 3) // Two stop bits select
#define PL011_UARTLCR_H_EPS (1 << 2) // Even parity select
#define PL011_UARTLCR_H_PEN (1 << 1) // Parity Enable
#define PL011_UARTLCR_H_BRK (1 << 0) // Send break
/*
Programmed hardware of Serial port.
@return Always return EFI_UNSUPPORTED.
**/
RETURN_STATUS
EFIAPI
PL011UartInitialize (
IN UINTN UartBase,
IN UINTN BaudRate,
IN UINTN LineControl
);
/**
Write data to serial device.
@param Buffer Point of data buffer which need to be writed.
@param NumberOfBytes Number of output bytes which are cached in Buffer.
@retval 0 Write data failed.
@retval !0 Actual number of bytes writed to serial device.
**/
UINTN
EFIAPI
PL011UartWrite (
IN UINTN UartBase,
IN UINT8 *Buffer,
IN UINTN NumberOfBytes
);
/**
Read data from serial device and save the datas in buffer.
@param Buffer Point of data buffer which need to be writed.
@param NumberOfBytes Number of output bytes which are cached in Buffer.
@retval 0 Read data failed.
@retval !0 Aactual number of bytes read from serial device.
**/
UINTN
EFIAPI
PL011UartRead (
IN UINTN UartBase,
OUT UINT8 *Buffer,
IN UINTN NumberOfBytes
);
/**
Check to see if any data is avaiable to be read from the debug device.
@retval EFI_SUCCESS At least one byte of data is avaiable to be read
@retval EFI_NOT_READY No data is avaiable to be read
@retval EFI_DEVICE_ERROR The serial device is not functioning properly
**/
BOOLEAN
EFIAPI
PL011UartPoll (
IN UINTN UartBase
);
#endif
|
