Merge zed.eecs.umich.edu:/.automount/fox/y/mserrano/m5_new/m5

into  zed.eecs.umich.edu:/z/benash/bk/m5

SConscript:
dev/ide_disk.hh:
    Formatting.
dev/ide_ctrl.cc:
    Endianness
dev/ide_disk.cc:
dev/pcidev.cc:
dev/tsunami_io.cc:
dev/uart8250.cc:
    Clean up code.

--HG--
extra : convert_revision : cb554f0e3a701371d2106cd7e11a4a22f773acc2

12 files changed, 223 insertions, 184 deletions

diff --git a/dev/ide_ctrl.cc b/dev/ide_ctrl.cc
index a2b27d01a..2c86d27c7 100644
--- a/dev/ide_ctrl.cc
+++ b/dev/ide_ctrl.cc
@@ -75,13 +75,13 @@ IdeController::IdeController(Params *p)
     bmi_size = BARSize[4];
 
     // zero out all of the registers
-    memset(bmi_regs, 0, sizeof(bmi_regs));
+    memset(bmi_regs.data, 0, sizeof(bmi_regs));
     memset(pci_config_regs.data, 0, sizeof(pci_config_regs.data));
 
     // setup initial values
     pci_config_regs.idetim = htoa((uint32_t)0x80008000); // enable both channels
-    *(uint8_t *)&bmi_regs[BMIS0] = 0x60;
-    *(uint8_t *)&bmi_regs[BMIS1] = 0x60;
+    bmi_regs.bmis0 = DMA1CAP | DMA0CAP;
+    bmi_regs.bmis1 = DMA1CAP | DMA0CAP;
 
     // reset all internal variables
     io_enabled = false;
@@ -218,18 +218,18 @@ IdeController::setDmaComplete(IdeDisk *disk)
 
     if (diskNum < 2) {
         // clear the start/stop bit in the command register
-        bmi_regs[BMIC0] &= ~SSBM;
+        bmi_regs.bmic0 &= ~SSBM;
         // clear the bus master active bit in the status register
-        bmi_regs[BMIS0] &= ~BMIDEA;
+        bmi_regs.bmis0 &= ~BMIDEA;
         // set the interrupt bit
-        bmi_regs[BMIS0] |= IDEINTS;
+        bmi_regs.bmis0 |= IDEINTS;
     } else {
         // clear the start/stop bit in the command register
-        bmi_regs[BMIC1] &= ~SSBM;
+        bmi_regs.bmic1 &= ~SSBM;
         // clear the bus master active bit in the status register
-        bmi_regs[BMIS1] &= ~BMIDEA;
+        bmi_regs.bmis1 &= ~BMIDEA;
         // set the interrupt bit
-        bmi_regs[BMIS1] |= IDEINTS;
+        bmi_regs.bmis1 |= IDEINTS;
     }
 }
 
@@ -261,7 +261,8 @@ IdeController::ReadConfig(int offset, int size, uint8_t *data)
 
     if (offset < PCI_DEVICE_SPECIFIC) {
         PciDev::ReadConfig(offset, size, data);
-    } else if (offset >= IDE_CTRL_CONFIG_START && (offset + size) <= IDE_CTRL_CONFIG_END) {
+    } else if (offset >= IDE_CTRL_CONFIG_START &&
+               (offset + size) <= IDE_CTRL_CONFIG_END) {
 
         config_offset = offset - IDE_CTRL_CONFIG_START;
         dword = 0;
@@ -299,7 +300,8 @@ IdeController::WriteConfig(int offset, int size, uint32_t data)
 
     if (offset < PCI_DEVICE_SPECIFIC) {
         PciDev::WriteConfig(offset, size, data);
-    } else if (offset >= IDE_CTRL_CONFIG_START && (offset + size) <= IDE_CTRL_CONFIG_END) {
+    } else if (offset >= IDE_CTRL_CONFIG_START &&
+               (offset + size) <= IDE_CTRL_CONFIG_END) {
 
         config_offset = offset - IDE_CTRL_CONFIG_START;
 
@@ -401,7 +403,6 @@ IdeController::read(MemReqPtr &req, uint8_t *data)
     RegType_t type;
     int disk;
 
-
     /*   union
      *   +--  --+--  --+--  --+--  --+
      *   |  0   |  1   |  2   |  3   |
@@ -430,15 +431,15 @@ IdeController::read(MemReqPtr &req, uint8_t *data)
       case BMI_BLOCK:
         switch (req->size) {
           case sizeof(uint8_t):
-            memcpy(&byte, &bmi_regs[offset], sizeof(uint8_t));
+            memcpy(&byte, &bmi_regs.data[offset], sizeof(uint8_t));
             *data = byte;
             break;
           case sizeof(uint16_t):
-            memcpy(&byte, &bmi_regs[offset], sizeof(uint16_t));
+            memcpy(&byte, &bmi_regs.data[offset], sizeof(uint16_t));
             *(uint16_t*)data = htoa(word[0]);
             break;
           case sizeof(uint32_t):
-            memcpy(&byte, &bmi_regs[offset], sizeof(uint32_t));
+            memcpy(&byte, &bmi_regs.data[offset], sizeof(uint32_t));
             *(uint32_t*)data = htoa(dword);
             break;
           default:
@@ -479,6 +480,8 @@ IdeController::read(MemReqPtr &req, uint8_t *data)
                 panic("IDE read of command reg of invalid size: %#x\n", req->size);
         }
         break;
+      default:
+        panic("IDE controller read of unknown register block type!\n");
     }
 
     DPRINTF(IdeCtrl, "read from offset: %#x size: %#x data: %#x\n",
@@ -492,40 +495,29 @@ IdeController::write(MemReqPtr &req, const uint8_t *data)
 {
     Addr offset;
     bool primary;
-    bool byte;
-    bool cmdBlk;
     RegType_t type;
     int disk;
 
-    parseAddr(req->paddr, offset, primary, type);
-    byte = (req->size == sizeof(uint8_t)) ? true : false;
-    cmdBlk = (type == COMMAND_BLOCK) ? true : false;
+    union {
+        uint8_t byte;
+        uint16_t word[2];
+        uint32_t dword;
+    };
 
-    DPRINTF(IdeCtrl, "write to offset: %#x size: %#x data: %#x\n",
-            offset, req->size,
-            (*(uint32_t *)data) & (0xffffffff >> 8 * (4 - req->size)));
+    dword = 0;
+
+    parseAddr(req->paddr, offset, primary, type);
 
     uint8_t oldVal, newVal;
 
     if (!io_enabled)
         return No_Fault;
 
-    if (type == BMI_BLOCK && !bm_enabled)
-        return No_Fault;
-
-    if (type != BMI_BLOCK) {
-        // shadow the dev bit
-        if (type == COMMAND_BLOCK && offset == IDE_SELECT_OFFSET) {
-            uint8_t *devBit = (primary ? &dev[0] : &dev[1]);
-            *devBit = ((*data & IDE_SELECT_DEV_BIT) ? 1 : 0);
-        }
-
-        assert(req->size != sizeof(uint32_t));
+    switch (type) {
+      case BMI_BLOCK:
+        if (!bm_enabled)
+            return No_Fault;
 
-        disk = getDisk(primary);
-        if (disks[disk])
-            disks[disk]->write(offset, byte, cmdBlk, data);
-    } else {
         switch (offset) {
             // Bus master IDE command register
           case BMIC1:
@@ -536,8 +528,9 @@ IdeController::write(MemReqPtr &req, const uint8_t *data)
             // select the current disk based on DEV bit
             disk = getDisk(primary);
 
-            oldVal = bmi_regs[offset];
-            newVal = *data;
+            oldVal = bmi_regs.data[offset];
+            byte = *data;
+            newVal = byte;
 
             // if a DMA transfer is in progress, R/W control cannot change
             if (oldVal & SSBM) {
@@ -553,7 +546,7 @@ IdeController::write(MemReqPtr &req, const uint8_t *data)
                     DPRINTF(IdeCtrl, "Stopping DMA transfer\n");
 
                     // clear the BMIDEA bit
-                    bmi_regs[offset + 0x2] &= ~BMIDEA;
+                    bmi_regs.data[offset + 0x2] &= ~BMIDEA;
 
                     if (disks[disk] == NULL)
                         panic("DMA stop for disk %d which does not exist\n",
@@ -566,7 +559,7 @@ IdeController::write(MemReqPtr &req, const uint8_t *data)
                     DPRINTF(IdeCtrl, "Starting DMA transfer\n");
 
                     // set the BMIDEA bit
-                    bmi_regs[offset + 0x2] |= BMIDEA;
+                    bmi_regs.data[offset + 0x2] |= BMIDEA;
 
                     if (disks[disk] == NULL)
                         panic("DMA start for disk %d which does not exist\n",
@@ -574,14 +567,14 @@ IdeController::write(MemReqPtr &req, const uint8_t *data)
 
                     // inform the disk of the DMA transfer start
                     if (primary)
-                        disks[disk]->startDma(*(uint32_t *)&bmi_regs[BMIDTP0]);
+                        disks[disk]->startDma(bmi_regs.bmidtp0);
                     else
-                        disks[disk]->startDma(*(uint32_t *)&bmi_regs[BMIDTP1]);
+                        disks[disk]->startDma(bmi_regs.bmidtp1);
                 }
             }
 
             // update the register value
-            bmi_regs[offset] = newVal;
+            bmi_regs.data[offset] = newVal;
             break;
 
             // Bus master IDE status register
@@ -590,8 +583,9 @@ IdeController::write(MemReqPtr &req, const uint8_t *data)
             if (req->size != sizeof(uint8_t))
                 panic("Invalid BMIS write size: %x\n", req->size);
 
-            oldVal = bmi_regs[offset];
-            newVal = *data;
+            oldVal = bmi_regs.data[offset];
+            byte = *data;
+            newVal = byte;
 
             // the BMIDEA bit is RO
             newVal |= (oldVal & BMIDEA);
@@ -607,7 +601,7 @@ IdeController::write(MemReqPtr &req, const uint8_t *data)
             else
                 (oldVal & IDEDMAE) ? newVal |= IDEDMAE : newVal &= ~IDEDMAE;
 
-            bmi_regs[offset] = newVal;
+            bmi_regs.data[offset] = newVal;
             break;
 
             // Bus master IDE descriptor table pointer register
@@ -616,7 +610,8 @@ IdeController::write(MemReqPtr &req, const uint8_t *data)
             if (req->size != sizeof(uint32_t))
                 panic("Invalid BMIDTP write size: %x\n", req->size);
 
-            *(uint32_t *)&bmi_regs[offset] = *(uint32_t *)data & ~0x3;
+            dword = htoa(*(uint32_t *)data & ~0x3);
+            *(uint32_t *)&bmi_regs.data[offset] = dword;
             break;
 
           default:
@@ -627,10 +622,53 @@ IdeController::write(MemReqPtr &req, const uint8_t *data)
                       req->size);
 
             // do a default copy of data into the registers
-            memcpy((void *)&bmi_regs[offset], data, req->size);
+            memcpy((void *)&bmi_regs.data[offset], data, req->size);
+        }
+        break;
+      case COMMAND_BLOCK:
+        if (offset == IDE_SELECT_OFFSET) {
+            uint8_t *devBit = (primary ? &dev[0] : &dev[1]);
+            *devBit = ((*data & IDE_SELECT_DEV_BIT) ? 1 : 0);
         }
+        // fall-through ok!
+      case CONTROL_BLOCK:
+        disk = getDisk(primary);
+
+        if (disks[disk] == NULL)
+            break;
+
+        switch (offset) {
+          case DATA_OFFSET:
+            switch (req->size) {
+              case sizeof(uint16_t):
+                word[0] = htoa(*(uint16_t*)data);
+                disks[disk]->write(offset, type, (uint8_t*)&word[0]);
+                break;
+
+              case sizeof(uint32_t):
+                dword = htoa(*(uint32_t*)data);
+                disks[disk]->write(offset, type, (uint8_t*)&word[0]);
+                disks[disk]->write(offset, type, (uint8_t*)&word[1]);
+                break;
+              default:
+                panic("IDE write of data reg invalid size: %#x\n", req->size);
+            }
+            break;
+          default:
+            if (req->size == sizeof(uint8_t)) {
+                byte = *data;
+                disks[disk]->write(offset, type, &byte);
+            } else
+                panic("IDE write of command reg of invalid size: %#x\n", req->size);
+        }
+        break;
+      default:
+        panic("IDE controller write of unknown register block type!\n");
     }
 
+    DPRINTF(IdeCtrl, "write to offset: %#x size: %#x data: %#x\n",
+            offset, req->size, dword);
+
     return No_Fault;
 }
 
@@ -657,14 +695,14 @@ IdeController::serialize(std::ostream &os)
     SERIALIZE_SCALAR(bmi_size);
 
     // Serialize registers
-    SERIALIZE_ARRAY(bmi_regs, 16);
-    SERIALIZE_ARRAY(dev, 2);
-    SERIALIZE_ARRAY(pci_config_regs.data, 22);
+    SERIALIZE_ARRAY(bmi_regs.data, sizeof(bmi_regs));
+    SERIALIZE_ARRAY(dev, sizeof(dev));
+    SERIALIZE_ARRAY(pci_config_regs.data, sizeof(pci_config_regs));
 
     // Serialize internal state
     SERIALIZE_SCALAR(io_enabled);
     SERIALIZE_SCALAR(bm_enabled);
-    SERIALIZE_ARRAY(cmd_in_progress, 4);
+    SERIALIZE_ARRAY(cmd_in_progress, sizeof(cmd_in_progress));
 }
 
 void
@@ -686,14 +724,14 @@ IdeController::unserialize(Checkpoint *cp, const std::string &section)
     UNSERIALIZE_SCALAR(bmi_size);
 
     // Unserialize registers
-    UNSERIALIZE_ARRAY(bmi_regs, 16);
-    UNSERIALIZE_ARRAY(dev, 2);
-    UNSERIALIZE_ARRAY(pci_config_regs.data, 22);
+    UNSERIALIZE_ARRAY(bmi_regs.data, sizeof(bmi_regs));
+    UNSERIALIZE_ARRAY(dev, sizeof(dev));
+    UNSERIALIZE_ARRAY(pci_config_regs.data, sizeof(pci_config_regs));
 
     // Unserialize internal state
     UNSERIALIZE_SCALAR(io_enabled);
     UNSERIALIZE_SCALAR(bm_enabled);
-    UNSERIALIZE_ARRAY(cmd_in_progress, 4);
+    UNSERIALIZE_ARRAY(cmd_in_progress, sizeof(cmd_in_progress));
 
     if (pioInterface) {
         pioInterface->addAddrRange(RangeSize(pri_cmd_addr, pri_cmd_size));
diff --git a/dev/ide_ctrl.hh b/dev/ide_ctrl.hh
index 2164f2f4a..51bdd93b1 100644
--- a/dev/ide_ctrl.hh
+++ b/dev/ide_ctrl.hh
@@ -110,7 +110,22 @@ class IdeController : public PciDev
 
   private:
     /** Registers used for bus master interface */
-    uint8_t bmi_regs[16];
+    union {
+        uint8_t data[16];
+
+        struct {
+            uint8_t bmic0;
+            uint8_t padding_0;
+            uint8_t bmis0;
+            uint8_t padding_1;
+            uint32_t bmidtp0;
+            uint8_t bmic1;
+            uint8_t padding_2;
+            uint8_t bmis1;
+            uint8_t padding_3;
+            uint32_t bmidtp1;
+        };
+    } bmi_regs;
     /** Shadows of the device select bit */
     uint8_t dev[2];
     /** Registers used in device specific PCI configuration */
diff --git a/dev/ide_disk.cc b/dev/ide_disk.cc
index 74d2ae6de..39eb2e698 100644
--- a/dev/ide_disk.cc
+++ b/dev/ide_disk.cc
@@ -218,18 +218,12 @@ IdeDisk::read(const Addr &offset, RegType_t type, uint8_t *data)
 
     switch (type) {
       case COMMAND_BLOCK:
-        if (offset == STATUS_OFFSET)
-            action = ACT_STAT_READ;
-        else if (offset == DATA_OFFSET)
-            action = ACT_DATA_READ_SHORT;
-
         switch (offset) {
-          // Data transfers occur 16 bits at a time
+          // Data transfers occur two bytes at a time
           case DATA_OFFSET:
-            // use memcpy to preserve IDE's little-endianess
             memcpy(data, &cmdReg.data, sizeof(uint16_t));
+            action = ACT_DATA_READ_SHORT;
             break;
-          // All other transfers are 8-bit
           case ERROR_OFFSET:
             *data = cmdReg.error;
             break;
@@ -250,6 +244,7 @@ IdeDisk::read(const Addr &offset, RegType_t type, uint8_t *data)
             break;
           case STATUS_OFFSET:
             *data = status;
+            action = ACT_STAT_READ;
             break;
           default:
             panic("Invalid IDE command register offset: %#x\n", offset);
@@ -261,7 +256,6 @@ IdeDisk::read(const Addr &offset, RegType_t type, uint8_t *data)
         else
             panic("Invalid IDE control register offset: %#x\n", offset);
         break;
-
       default:
         panic("Unknown register block!\n");
     }
@@ -271,76 +265,59 @@ IdeDisk::read(const Addr &offset, RegType_t type, uint8_t *data)
 }
 
 void
-IdeDisk::write(const Addr &offset, bool byte, bool cmdBlk, const uint8_t *data)
+IdeDisk::write(const Addr &offset, RegType_t type, const uint8_t *data)
 {
     DevAction_t action = ACT_NONE;
 
-    if (cmdBlk) {
-
-        if (!byte && offset != DATA_OFFSET)
-            panic("Invalid 16-bit write, only allowed on data reg\n");
-
-        if (!byte)
-            *((uint16_t *)&cmdReg.data) = *(uint16_t *)data;
-        else {
-            switch (offset) {
-              case DATA_OFFSET:
-                memcpy(&cmdReg.data, data, sizeof(uint16_t));
-                break;
-              case FEATURES_OFFSET:
-                //cmdReg.features = *data;
-                break;
-              case NSECTOR_OFFSET:
-                cmdReg.sec_count = *data;
-                break;
-              case SECTOR_OFFSET:
-                cmdReg.sec_num = *data;
-                break;
-              case LCYL_OFFSET:
-                cmdReg.cyl_low = *data;
-                break;
-              case HCYL_OFFSET:
-                cmdReg.cyl_high = *data;
-                break;
-              case DRIVE_OFFSET:
-                cmdReg.drive = *data;
-                break;
-              case COMMAND_OFFSET:
-                cmdReg.command = *data;
-                break;
-              default:
-                panic("Invalid IDE command register offset: %#x\n", offset);
-            }
-        }
-
-        // determine if an action needs to be taken on the state machine
-        if (offset == COMMAND_OFFSET) {
-            action = ACT_CMD_WRITE;
-        } else if (offset == DATA_OFFSET) {
-            if (byte)
-                action = ACT_DATA_WRITE_BYTE;
-            else
-                action = ACT_DATA_WRITE_SHORT;
-        } else if (offset == DRIVE_OFFSET) {
+    switch (type) {
+      case COMMAND_BLOCK:
+        switch (offset) {
+          case DATA_OFFSET:
+            memcpy(&cmdReg.data, data, sizeof(uint16_t));
+            action = ACT_DATA_WRITE_SHORT;
+            break;
+          case FEATURES_OFFSET:
+            break;
+          case NSECTOR_OFFSET:
+            cmdReg.sec_count = *data;
+            break;
+          case SECTOR_OFFSET:
+            cmdReg.sec_num = *data;
+            break;
+          case LCYL_OFFSET:
+            cmdReg.cyl_low = *data;
+            break;
+          case HCYL_OFFSET:
+            cmdReg.cyl_high = *data;
+            break;
+          case DRIVE_OFFSET:
+            cmdReg.drive = *data;
             action = ACT_SELECT_WRITE;
+            break;
+          case COMMAND_OFFSET:
+            cmdReg.command = *data;
+            action = ACT_CMD_WRITE;
+            break;
+          default:
+            panic("Invalid IDE command register offset: %#x\n", offset);
         }
-
-    } else {
-        if (offset != CONTROL_OFFSET)
-            panic("Invalid disk control register offset: %#x\n", offset);
-
-        if (!byte)
-            panic("Invalid 16-bit write to control block\n");
-
-        if (*data & CONTROL_RST_BIT) {
-            // force the device into the reset state
-            devState = Device_Srst;
-            action = ACT_SRST_SET;
-        } else if (devState == Device_Srst && !(*data & CONTROL_RST_BIT)) {
-            action = ACT_SRST_CLEAR;
+        break;
+      case CONTROL_BLOCK:
+        if (offset == CONTROL_OFFSET) {
+            if (*data & CONTROL_RST_BIT) {
+                // force the device into the reset state
+                devState = Device_Srst;
+                action = ACT_SRST_SET;
+            } else if (devState == Device_Srst && !(*data & CONTROL_RST_BIT))
+                action = ACT_SRST_CLEAR;
+
+            nIENBit = (*data & CONTROL_IEN_BIT) ? true : false;
         }
-
-        nIENBit = (*data & CONTROL_IEN_BIT) ? true : false;
+        else
+            panic("Invalid IDE control register offset: %#x\n", offset);
+        break;
+      default:
+        panic("Unknown register block!\n");
     }
 
     if (action != ACT_NONE)
@@ -793,7 +770,7 @@ IdeDisk::intrPost()
 
     // talk to controller to set interrupt
     if (ctrl) {
-        ctrl->bmi_regs[BMIS0] |= IDEINTS;
+        ctrl->bmi_regs.bmis0 |= IDEINTS;
         ctrl->intrPost();
     }
 }
diff --git a/dev/ide_disk.hh b/dev/ide_disk.hh
index 9799e2d38..ceec11925 100644
--- a/dev/ide_disk.hh
+++ b/dev/ide_disk.hh
@@ -271,7 +271,7 @@ class IdeDisk : public SimObject
 
     // Device register read/write
     void read(const Addr &offset, RegType_t type, uint8_t *data);
-    void write(const Addr &offset, bool byte, bool cmdBlk, const uint8_t *data);
+    void write(const Addr &offset, RegType_t type, const uint8_t *data);
 
     // Start/abort functions
     void startDma(const uint32_t &prdTableBase);
diff --git a/dev/pcidev.cc b/dev/pcidev.cc
index 31c44bffa..c74fb035c 100644
--- a/dev/pcidev.cc
+++ b/dev/pcidev.cc
@@ -115,10 +115,6 @@ PciDev::WriteConfig(int offset, int size, uint32_t data)
 
     uint32_t barnum;
 
-    uint8_t byte_value;
-    uint16_t half_value;
-    uint32_t word_value;
-
     DPRINTF(PCIDEV,
             "write device: %#x function: %#x reg: %#x size: %d data: %#x\n",
             params()->deviceNum, params()->functionNum, offset, size,
@@ -128,7 +124,7 @@ PciDev::WriteConfig(int offset, int size, uint32_t data)
 
     switch (size) {
       case sizeof(uint8_t): // 1-byte access
-        byte_value = data;
+        uint8_t byte_value = data;
         switch (offset) {
           case PCI0_INTERRUPT_LINE:
           case PCI_CACHE_LINE_SIZE:
@@ -148,7 +144,7 @@ PciDev::WriteConfig(int offset, int size, uint32_t data)
         break;
 
       case sizeof(uint16_t): // 2-byte access
-        half_value = data;
+        uint16_t half_value = data;
         switch (offset) {
           case PCI_COMMAND:
           case PCI_STATUS:
@@ -162,7 +158,7 @@ PciDev::WriteConfig(int offset, int size, uint32_t data)
         break;
 
       case sizeof(uint32_t): // 4-byte access
-        word_value = data;
+        uint32_t word_value = data;
         switch (offset) {
           case PCI0_BASE_ADDR0:
           case PCI0_BASE_ADDR1:
@@ -194,7 +190,7 @@ PciDev::WriteConfig(int offset, int size, uint32_t data)
                         htoa((word_value & ~0x3) |
                         (htoa(config.data[offset]) & 0x3));
 
-                    if (word_value != 0x1) {
+                    if (word_value &= ~0x1) {
                         Addr base_addr = (word_value & ~0x1) + TSUNAMI_PCI0_IO;
                         Addr base_size = BARSize[barnum];
 
diff --git a/dev/rtcreg.h b/dev/rtcreg.h
index 0b33c25b2..032e22ab5 100644
--- a/dev/rtcreg.h
+++ b/dev/rtcreg.h
@@ -36,8 +36,22 @@
 #define RTC_DOM                 0x07
 #define RTC_MON                 0x08
 #define RTC_YEAR                0x09
+
 #define RTC_CNTRL_REGA          0x0A
+#define  RTCA_1024HZ            0x06  /* 1024Hz periodic interrupt frequency */
+#define  RTCA_32768HZ           0x20  /* 22-stage divider, 32.768KHz timebase */
+#define  RTCA_UIP               0x80  /* 1 = date and time update in progress */
+
 #define RTC_CNTRL_REGB          0x0B
+#define  RTCB_DST               0x01  /* USA Daylight Savings Time enable */
+#define  RTCB_24HR              0x02  /* 0 = 12 hours, 1 = 24 hours */
+#define  RTCB_BIN               0x04  /* 0 = BCD, 1 = Binary coded time */
+#define  RTCB_SQWE              0x08  /* 1 = output sqare wave at SQW pin */
+#define  RTCB_UPDT_IE           0x10  /* 1 = enable update-ended interrupt */
+#define  RTCB_ALRM_IE           0x20  /* 1 = enable alarm interrupt */
+#define  RTCB_PRDC_IE           0x40  /* 1 = enable periodic clock interrupt */
+#define  RTCB_NO_UPDT           0x80  /* stop clock updates */
+
 #define RTC_CNTRL_REGC          0x0C
 #define RTC_CNTRL_REGD          0x0D
 
diff --git a/dev/tsunami_io.cc b/dev/tsunami_io.cc
index 82fe40e0a..f9dcbb8e0 100644
--- a/dev/tsunami_io.cc
+++ b/dev/tsunami_io.cc
@@ -52,14 +52,11 @@ using namespace std;
 
 #define UNIX_YEAR_OFFSET 52
 
-struct tm TsunamiIO::tm = { 0 };
-
 // Timer Event for Periodic interrupt of RTC
 TsunamiIO::RTCEvent::RTCEvent(Tsunami* t, Tick i)
     : Event(&mainEventQueue), tsunami(t), interval(i)
 {
     DPRINTF(MC146818, "RTC Event Initilizing\n");
-    intr_count = 0;
     schedule(curTick + interval);
 }
 
@@ -70,11 +67,6 @@ TsunamiIO::RTCEvent::process()
     schedule(curTick + interval);
     //Actually interrupt the processor here
     tsunami->cchip->postRTC();
-
-    if (intr_count == 1023)
-        tm.tm_sec = (tm.tm_sec + 1) % 60;
-
-    intr_count = (intr_count + 1) % 1024;
 }
 
 const char *
@@ -98,6 +90,11 @@ TsunamiIO::RTCEvent::unserialize(Checkpoint *cp, const std::string &section)
     reschedule(time);
 }
 
+void
+TsunamiIO::RTCEvent::scheduleIntr()
+{
+  schedule(curTick + interval);
+}
 
 // Timer Event for PIT Timers
 TsunamiIO::ClockEvent::ClockEvent()
@@ -125,10 +122,8 @@ TsunamiIO::ClockEvent::process()
     DPRINTF(Tsunami, "Timer Interrupt\n");
     if (mode == 0)
         status = 0x20; // set bit that linux is looking for
-    else
-        schedule(curTick + interval);
-
-    current_count--; //decrement count
+    else if (mode == 2)
+        schedule(curTick + current_count*interval);
 }
 
 void
@@ -301,12 +296,12 @@ TsunamiIO::read(MemReqPtr &req, uint8_t *data)
           case TSDEV_RTC_DATA:
             switch(RTCAddress) {
               case RTC_CNTRL_REGA:
-                *(uint8_t*)data = uip << 7 | 0x26;
+                *(uint8_t*)data = uip << 7 | RTCA_32768HZ | RTCA_1024HZ;
                 uip = !uip;
                 return No_Fault;
               case RTC_CNTRL_REGB:
                 // DM and 24/12 and UIE
-                *(uint8_t*)data = 0x46;
+                *(uint8_t*)data = RTCB_PRDC_IE | RTCB_BIN | RTCB_24HR;
                 return No_Fault;
               case RTC_CNTRL_REGC:
                 // If we want to support RTC user access in linux
@@ -331,7 +326,7 @@ TsunamiIO::read(MemReqPtr &req, uint8_t *data)
                 *(uint8_t *)data = tm.tm_hour;
                 return No_Fault;
               case RTC_DOW:
-                *(uint8_t *)data = tm.tm_wday;
+                *(uint8_t *)data = tm.tm_wday + 1;
                 return No_Fault;
               case RTC_DOM:
                 *(uint8_t *)data = tm.tm_mday;
@@ -340,20 +335,11 @@ TsunamiIO::read(MemReqPtr &req, uint8_t *data)
                 *(uint8_t *)data = tm.tm_mon + 1;
                 return No_Fault;
               case RTC_YEAR:
-                *(uint8_t *)data = tm.tm_year - UNIX_YEAR_OFFSET;
+                *(uint8_t *)data = tm.tm_year;
                 return No_Fault;
               default:
                 panic("Unknown RTC Address\n");
             }
-
-          /* Added for keyboard reads */
-          case TSDEV_KBD:
-            *(uint8_t *)data = 0x00;
-            return No_Fault;
-          /* Added for ATA PCI DMA */
-          case ATA_PCI_DMA:
-            *(uint8_t *)data = 0x00;
-            return No_Fault;
           default:
             panic("I/O Read - va%#x size %d\n", req->vaddr, req->size);
         }
@@ -447,10 +433,10 @@ TsunamiIO::write(MemReqPtr &req, const uint8_t *data)
                 switch(*(uint8_t*)data >> 6) {
                   case 0:
                     timer0.LatchCount();
-                    break;
+                    return No_Fault;
                   case 2:
                     timer2.LatchCount();
-                    break;
+                    return No_Fault;
                   default:
                     panic("Read Back Command not implemented\n");
                 }
@@ -488,9 +474,10 @@ TsunamiIO::write(MemReqPtr &req, const uint8_t *data)
             /* two writes before we actually start the Timer
                so I set a flag in the timerData */
             if(timerData & 0x1000) {
-                timerData &= 0x1000;
+                timerData &= ~0x1000;
                 timerData += *(uint8_t*)data << 8;
                 timer0.Program(timerData);
+                timerData = 0;
             } else {
                 timerData = *(uint8_t*)data;
                 timerData |= 0x1000;
@@ -504,12 +491,26 @@ TsunamiIO::write(MemReqPtr &req, const uint8_t *data)
           case TSDEV_RTC_DATA:
             switch(RTCAddress) {
               case RTC_CNTRL_REGA:
+                if (*data != (RTCA_32768HZ | RTCA_1024HZ))
+                    panic("Unimplemented RTC register A value write!\n");
                 return No_Fault;
               case RTC_CNTRL_REGB:
+                if ((*data & ~(RTCB_PRDC_IE | RTCB_SQWE)) != (RTCB_BIN | RTCB_24HR))
+                    panic("Write to RTC reg B bits that are not implemented!\n");
+
+                if (*data & RTCB_PRDC_IE) {
+                    if (!rtc.scheduled())
+                        rtc.scheduleIntr();
+                } else {
+                    if (rtc.scheduled())
+                        rtc.deschedule();
+                }
                 return No_Fault;
               case RTC_CNTRL_REGC:
+                panic("Write to RTC reg C not implemented!\n");
                 return No_Fault;
               case RTC_CNTRL_REGD:
+                panic("Write to RTC reg D not implemented!\n");
                 return No_Fault;
               case RTC_SEC:
                 tm.tm_sec = *(uint8_t *)data;
@@ -527,12 +528,11 @@ TsunamiIO::write(MemReqPtr &req, const uint8_t *data)
                 tm.tm_mday = *(uint8_t *)data;
                 return No_Fault;
               case RTC_MON:
-                 tm.tm_mon = *(uint8_t *)data - 1;
+                 tm.tm_mon = *(uint8_t *)data;
                 return No_Fault;
               case RTC_YEAR:
-                tm.tm_year = *(uint8_t *)data + UNIX_YEAR_OFFSET;
+                tm.tm_year = *(uint8_t *)data;
                 return No_Fault;
-            //panic("RTC Write not implmented (rtc.o won't work)\n");
             }
           default:
             panic("I/O Write - va%#x size %d\n", req->vaddr, req->size);
diff --git a/dev/tsunami_io.hh b/dev/tsunami_io.hh
index 4b28635e8..7054b4ff4 100644
--- a/dev/tsunami_io.hh
+++ b/dev/tsunami_io.hh
@@ -51,7 +51,7 @@ class TsunamiIO : public PioDevice
     /** The size of mappad from the above address */
     static const Addr size = 0xff;
 
-    static struct tm tm;
+    struct tm tm;
 
     /**
      * In Tsunami RTC only has two i/o ports one for data and one for
@@ -154,9 +154,6 @@ class TsunamiIO : public PioDevice
         Tsunami* tsunami;
         Tick interval;
 
-        /** Count of the number of RTC interrupts that have occured */
-        uint32_t intr_count;
-
       public:
         /**
          * RTC Event initializes the RTC event by scheduling an event
@@ -165,7 +162,7 @@ class TsunamiIO : public PioDevice
         RTCEvent(Tsunami* t, Tick i);
 
         /**
-         * Interrupth the processor and reschedule the event.
+         * Interrupt the processor and reschedule the event.
          */
         virtual void process();
 
@@ -187,6 +184,8 @@ class TsunamiIO : public PioDevice
          * @param section The section name of this object
          */
         virtual void unserialize(Checkpoint *cp, const std::string &section);
+
+        void scheduleIntr();
     };
 
     /** uip UpdateInProgess says that the rtc is updating, but we just fake it
@@ -243,7 +242,7 @@ class TsunamiIO : public PioDevice
      * This variable contains a flag as to how many writes have happened, and
      * the time so far.
      */
-    uint32_t timerData;
+    uint16_t timerData;
 
   public:
     /**
diff --git a/dev/uart8250.cc b/dev/uart8250.cc
index ad3232686..013cbfd00 100644
--- a/dev/uart8250.cc
+++ b/dev/uart8250.cc
@@ -148,9 +148,9 @@ Uart8250::read(MemReqPtr &req, uint8_t *data)
             DPRINTF(Uart, "IIR Read, status = %#x\n", (uint32_t)status);
             status &= ~TX_INT;
             if (status & RX_INT)
-                *(uint8_t*)data = 0x4;
+                *(uint8_t*)data = IIR_RXID;
             else
-                *(uint8_t*)data = 0x1;
+                *(uint8_t*)data = IIR_NOPEND;
             break;
         case 0x3: // Line Control Register (LCR)
             *(uint8_t*)data = LCR;
diff --git a/dev/uart8250.hh b/dev/uart8250.hh
index 06a798e26..e85ad72c8 100644
--- a/dev/uart8250.hh
+++ b/dev/uart8250.hh
@@ -38,6 +38,9 @@
 #include "dev/io_device.hh"
 #include "dev/uart.hh"
 
+#define IIR_NOPEND 0x1
+#define IIR_RXID   0x4
+
 class SimConsole;
 class Platform;
 
diff --git a/kern/freebsd/freebsd_system.cc b/kern/freebsd/freebsd_system.cc
index 2eb80b8e9..3ff5f18ce 100644
--- a/kern/freebsd/freebsd_system.cc
+++ b/kern/freebsd/freebsd_system.cc
@@ -60,7 +60,6 @@ FreebsdSystem::FreebsdSystem(Params *p)
     skipCalibrateClocks = new FreebsdSkipCalibrateClocksEvent(&pcEventQueue, "calibrate_clocks");
     if (kernelSymtab->findAddress("calibrate_clocks", addr))
         skipCalibrateClocks->schedule(addr + sizeof(MachInst) * 2);
-
 }
 
 
diff --git a/kern/freebsd/freebsd_system.hh b/kern/freebsd/freebsd_system.hh
index 6b236e52e..6429b5690 100644
--- a/kern/freebsd/freebsd_system.hh
+++ b/kern/freebsd/freebsd_system.hh
@@ -34,9 +34,7 @@
 class FreebsdSystem : public System
 {
   private:
-
     SkipFuncEvent *skipDelayEvent;
-
     FreebsdSkipCalibrateClocksEvent *skipCalibrateClocks;
 
   public: