| Age | Commit message (Collapse) | Author |
|---|
|
currently the PC is incremented on an instruction granularity, and not as an
instruction's byte address. machine ISA instructions assume the PC is a byte
address, and is incremented accordingly. here we make the GPU model, and the
HSAIL instructions treat the PC as a byte address as well.
|
|
the GPUISA class is meant to encapsulate any ISA-specific behavior - special
register accesses, isa-specific WF/kernel state, etc. - in a generic enough
way so that it may be used in ISA-agnostic code.
gpu-compute: use the GPUISA object to advance the PC
the GPU model treats the PC as a pointer to individual instruction objects -
which are store in a contiguous array - and not a byte address to be fetched
from the real memory system. this is ok for HSAIL because all instructions
are considered by the model to be the same size.
in machine ISA, however, instructions may be 32b or 64b, and branches are
calculated by advancing the PC by the number of words (4 byte chunks) it
needs to advance in the real instruction stream. because of this there is
a mismatch between the PC we use to index into the instruction array, and
the actual byte address PC the ISA expects. here we move the PC advance
calculation to the ISA so that differences in the instrucion sizes may be
accounted for in generic way.
|
|
|
|
because every taken branch causes fetch to be discarded, we move the call
to the WF to avoid to have to call it from each and every branch instruction
type.
|
|
we are removing doGmReturn from the GM pipe, and adding completeAcc()
implementations for the HSAIL mem ops. the behavior in doGmReturn is
dependent on HSAIL and HSAIL mem ops, however the completion phase
of memory ops in machine ISA can be very different, even amongst individual
machine ISA mem ops. so we remove this functionality from the pipeline and
allow it to be implemented by the individual instructions.
|
|
this patch removes the GPUStaticInst enums that were defined in GPU.py.
instead, a simple set of attribute flags that can be set in the base
instruction class are used. this will help unify the attributes of HSAIL
and machine ISA instructions within the model itself.
because the static instrution now carries the attributes, a GPUDynInst
must carry a pointer to a valid GPUStaticInst so a new static kernel launch
instruction is added, which carries the attributes needed to perform a
the kernel launch.
|
|
|
|
|
|
the RequestDesc was previously implemented as a std::pair, which made
the implementation overly complex and error prone. here we encapsulate the
packet, primary, and secondary types all in a single data structure with
all members properly intialized in a ctor
|
|
This patch breaks out the most basic configuration options into a set
of base options, to allow them to be used also by scripts that do not
involve any ISA, and thus no actual CPUs or devices.
The patch also fixes a few modules so that they can be imported in a
NULL build, and avoid dragging in FSConfig every time Options is
imported.
|
|
Mostly just splitting out the floats ops and corresponding
reads/writes.
|
|
tracked down issue with ARM's version of gem5 using the "cluster" name.
The public/github version of ARM Gem5 does not use the "cluster" naming
mechanism.
Signed-off-by: Dam Sunwoo <dam.sunwoo@arm.com>
Signed-off-by: Jason Lowe-Power <jason@lowepower.com>
|
|
Improve PL011 console interactivity
Signed-off-by: Jason Lowe-Power <jason@lowepower.com>
|
|
Read() should not write anything when returning 0 (EOF).
This patch does not correct the same bug occuring for :
nbr_read=read(file, buf, nbytes)
When nbr_read<nbytes, nbytes bytes are copied into the virtual
RAM instead of nbr_read. If buf is smaller than nbytes, a
page fault occurs, even if buf is in fact bigger than nbr_read.
Signed-off-by: Jason Lowe-Power <jason@lowepower.com>
|
|
Modify the opClass assigned to AArch64 FP instructions from SimdFloat* to
Float*. Also create the FloatMemRead and FloatMemWrite opClasses, which
distinguishes writes to the INT and FP register banks.
Change the latency of (Simd)FloatMultAcc to 5, based on the Cortex-A72,
where the "latency" of FMADD is 3 if the next instruction is a FMADD and
has only the augend to destination dependency, otherwise it's 7 cycles.
Signed-off-by: Jason Lowe-Power <jason@lowepower.com>
|
|
Continue along the same line as the recent patch that made the
Ruby-related config scripts Python packages and make also the
configs/common directory a package.
All affected config scripts are updated (hopefully).
Note that this change makes it apparent that the current organisation
and naming of the config directory and its subdirectories is rather
chaotic. We mix scripts that are directly invoked with scripts that
merely contain convenience functions. While it is not addressed in
this patch we should follow up with a re-organisation of the
config structure, and renaming of some of the packages.
|
|
ClockedObject was changed to require its regStats() to be called from every
child class. If you forget to do this, the error was indecipherable. This
patch makes the error more clear.
|
|
|
|
Change-Id: I763cffe0c69f5ebbbf6a6eb12bec5c13d5d0161d
Reviewed-by: Andreas Hansson <andreas.hansson@arm.com>
Reviewed-by: Radhika Jagtap <radhika.jagtap@arm.com>
|
|
Added power-down state transitions to the DRAM controller model.
Added per rank parameter, outstandingEvents, which tracks the number
of outstanding command events and is used to determine when the
controller should transition to a low power state.
The controller will only transition when there are no outstanding events
scheduled and the number of command entries for the given rank is 0.
The outstandingEvents parameter is incremented for every RD/WR burst,
PRE, and REF event scheduled. ACT is implicitly covered by RD/WR
since burst will always issue and complete after a required ACT.
The parameter is decremented when the event is serviced (completed).
The controller will automatically transition to ACT power down,
PRE power down, or SREF.
Transition to ACT power down state scheduled from:
1) The RespondEvent, where read data is received from the memory.
ACT power-down entry will be scheduled when one or more banks is
open, all commands for the rank have completed (no more commands
scheduled), and there are no commands in queue for the rank
Transition to PRE power down scheduled from:
1) respondEvent, when all banks are closed, all commands have
completed, and there are no commands in queue for the rank
2) prechargeEvent when all banks are closed, all commands have
completed, and there are no commands in queue for the rank
3) refreshEvent, after the refresh is complete when the previous
state was ACT power-down
4) refreshEvent, after the refresh is complete when the previous
state was PRE power-down and there are commands in the queue.
Transition to SREF will be scheduled from:
1) refreshEvent, after the refresh is completes when the previous
state was PRE power-down with no commands in queue
Power-down exit commands are scheduled from:
1) The refreshEvent, prior to issuing a refresh
2) doDRAMAccess, to wake-up the rank for RD/WR command issue.
Self-refresh exit commands are scheduled from:
1) The next request event, when the queue has commands for the rank
in the readQueue or there are commands for the rank in the
writeQueue and the bus state is WRITE.
Change-Id: I6103f660776e36c686655e71d92ec7b5b752050a
Reviewed-by: Radhika Jagtap <radhika.jagtap@arm.com>
|
|
The per rank statistics are periodically updated based on
state transition and refresh events.
Add a method to update these when a dump event occurs to
ensure they reflect accurate values.
Specifically, need to ensure that the low-power state
durations, power, and energy are logged correctly.
Change-Id: Ib642a6668340de8f494a608bb34982e58ba7f1eb
Reviewed-by: Radhika Jagtap <radhika.jagtap@arm.com>
|
|
Add constraint that all ranks have to be in PWR_IDLE
before signaling drain complete
This will ensure that the banks are all closed and the rank
has exited any low-power states.
On suspend, update the power stats to sync the DRAM power logic
The logic maintains the location of the signalDrainDone
method, which is still triggered from either:
1) Read response event
2) Next request event
This ensures that the drain will complete in the READ bus
state and minimizes the changes required.
Change-Id: If1476e631ea7d5999fe50a0c9379c5967a90e3d1
Reviewed-by: Radhika Jagtap <radhika.jagtap@arm.com>
|
|
Add local variable to stores commands to be issued.
These commands are in order within a single bank but will be out
of order across banks & ranks.
A new procedure, flushCmdList, sorts commands across banks / ranks,
and flushes the sorted list, up to curTick() to DRAMPower.
This is currently called in refresh, once all previous commands are
guaranteed to have completed. Could be called in other events like
the powerEvent as well.
By only flushing commands up to curTick(), will not get out of sync
when flushed at a periodic stats dump (done in subsequent patch).
Change-Id: I4ac65a52407f64270db1e16a1fb04cfe7f638851
Reviewed-by: Radhika Jagtap <radhika.jagtap@arm.com>
|
|
Change-Id: I8992ddc1664c3ed4b2d36d8a34e4ce8be113b9de
Reviewed-by: Radhika Jagtap <radhika.jagtap@arm.com>
|
|
|
|
|
|
This commit adds missing non-predicated, scalar floating point
instructions. Specifically VRINT* floating point integer rounding
instructions and VSEL* floating point conditional selects.
Change-Id: I23cbd1389f151389ac8beb28a7d18d5f93d000e7
Reviewed-by: Andreas Sandberg <andreas.sandberg@arm.com>
Reviewed-by: Nathanael Premillieu <nathanael.premillieu@arm.com>
|
|
This patch moves the addition of network options into the Ruby module
to avoid the regressions all having to add it explicitly. Doing this
exposes an issue in our current config system though, namely the fact
that addtoPath is relative to the Python script being executed. Since
both example and regression scripts use the Ruby module we would end
up with two different (relative) paths being added. Instead we take a
first step at turning the config modules into Python packages, simply
by adding a __init__.py in the configs/ruby, configs/topologies and
configs/network subdirectories.
As a result, we can now add the top-level configs directory to the
Python search path, and then use the package names in the various
modules. The example scripts are also updated, and the messy
path-deducing variations in the scripts are unified.
|
|
|
|
The generic timer needs a pointer to an ArmSystem to wire itself to the
system register handler. This was previously specified as an instance
of System that was later cast to ArmSystem. Make this more robust by
specifying it as an ArmSystem in the Python interface and add a check
to make sure that it is non-NULL.
Change-Id: I989455e666f4ea324df28124edbbadfd094b0d02
Signed-off-by: Andreas Sandberg <andreas.sandberg@arm.com>
Reviewed-by: Nikos Nikoleris <nikos.nikoleris@arm.com>
|
|
This removes errors when building gem5.fast
|
|
Revamped version of garnet with more optimized single-cycle routers,
more configurability, and cleaner code.
|
|
Only garnet2.0 will be supported henceforth.
|
|
This patch adds port direction names to the links during topology
creation, which can be used for better printed names for the links
or for users to code up their own adaptive routing algorithms.
It also adds support for every router to have an independent latency
value to support heterogeneous topologies with the subsequent
garnet2.0 patch.
|
|
This patch makes the internal links within the network topology
unidirectional, thus allowing any deadlock-free routing algorithms to
be specified from the topology itself using weights.
This patch also renames Mesh.py and MeshDirCorners.py to
Mesh_XY.py and MeshDirCorners_XY.py (Mesh with XY routing).
It also adds a Mesh_westfirst.py and CrossbarGarnet.py topologies.
|
|
This patch adds a new file configs/network/Network.py to setup the network,
instead of doing that within Ruby.py.
|
|
networktest is essentially a collection of synthetic traffic patterns
for the network. The protocol name and the tester having the same name
led to multiple python configuration files with the same name, adding
confusion. This patch renames networktest to garnet_synthetic_traffic,
and also adds more synthetic traffic patterns.
|
|
Over the past 6 years, we realized that the protocol is essentially used
to run the garnet network in a standalone manner, and feed standard synthetic
traffic patterns through it.
|
|
Adding details, e.g. rip, rsp etc. to the kvm pagefault exit when in SE mode.
|
|
Instead of scheduling another event, this patch adds a warning in case gdb
is attached multiple times and the first attachement event has not been
processed yet.
|
|
This patch adds a method to the Wavefront class to compute the actual workgroup
size. This can be different from the maximum workgroup size specified when
launching the kernel through the NDRange object. Current solution is still not
optimal, as we are computing these for each wavefront and the dispatcher also
needs to have this information and can't actually call
Wavefront::computeActuallWgSz before the wavefronts are being created. A long
term solution would be to have a Workgroup class that deals with all these
details.
|
|
Adjust the traffic generator time-out so that the script works out of
the box
Change-Id: I6b3b6b11f98b094ae3acdbe09488c26e4aeb0ab4
Reviewed-by: Andreas Sandberg <andreas.sandberg@arm.com>
|
|
When loading a checkpoint, it's sometimes desirable to be able to test
whether an entry within a secion exists. This is currently done
automatically in the UNSERIALIZE_OPT_SCALAR macro, but it isn't
possible to do for arrays, containers, or enums. Instead of adding
even more macros, add a helper function (CheckpointIn::entryExists())
that tests for the presence of an entry.
Change-Id: I4b4646b03276b889fd3916efefff3bd552317dbc
Signed-off-by: Andreas Sandberg <andreas.sandberg@arm.com>
Reviewed-by: Nikos Nikoleris <nikos.nikoleris@arm.com>
|
|
Fixed AbstractController::queueMemoryWritePartial to specify the
correct size for partial memory writes.
|
|
print number of bytes written as a decimal number, not hex
|
|
Change-Id: If19b9c593b48ded1ea848f2d3710d4369ec8a221
Reviewed-by: Andreas Sandberg <andreas.sandberg@arm.com>
|
|
Two of the switcheroo tests were accidentally removed due to
unexpected Mercurial behavior.
Signed-off-by: Andreas Sandberg <andreas.sandberg@arm.com>
|
|
The drain did not wait until stages were ready again. Therefore, as a
result of messages in the TimeBuffer being drain, the state after the
drain was not consistent and asserts fired in some places when the
draining happened after a stage got blocked, but before the notification
arrived to the previous stages.
Change-Id: Ib50b3b40b7f745b62c1eba2931dec76860824c71
Reviewed-by: Andreas Sandberg <andreas.sandberg@arm.com>
|
|
The memtest and memcheck are not designed to test timing. Make them
functional only to make ref diffs less noisy in the future.
Signed-off-by: Andreas Sandberg <andreas.sandberg@arm.com>
|
|
The switcheroo tests only really serve to check functional
correctness. Checking for stat differences in them just increases the
size of reference diffs.
Signed-off-by: Andreas Sandberg <andreas.sandberg@arm.com>
|
