| Age | Commit message (Collapse) | Author |
|---|
|
DMA Controller was not being connected to the network for the MESI_Three_Level
protocol as was being done in the other protocol config files. Without this
patch, this protocol segfaults during startup.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
One step closer to shifting focus to the MinorCPU.
|
|
when trying to dual boot on arm build_drive_system will only use the default
values for the dtb file, number of processors, and disk image. if you are using
the non-default files by passing values on the command line for example, or by
making a new entry in Benchmarks.py, the build config scripts will still look
for the default files. this will lead to the wrong system files being used, or
the simulator will fail if you do not have them.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
|
|
This patch gives the user direct influence over the number of DRAM
ranks to make it easier to tune the memory density without affecting
the bandwidth (previously the only means of scaling the device count
was through the number of channels).
The patch also adds some basic sanity checks to ensure that the number
of ranks is a power of two (since we rely on bit slices in the address
decoding).
|
|
This patch adds the --memchecker option, to denote that a MemChecker
should be instantiated for the system. The exact usage of the MemChecker
depends on the system configuration.
For now CacheConfig.py makes use of the option, adding MemCheckerMonitor
instances between CPUs and D-Caches.
Note, however, that currently this only provides limited checking on a
running system; other parts of the system, such as I/O devices are not
monitored, and may cause warnings to be issued by the monitor.
|
|
More documentation at http://gem5.org/Simpoints
Steps to profile, generate, and use SimPoints with gem5:
1. To profile workload and generate SimPoint BBV file, use the
following option:
--simpoint-profile --simpoint-interval <interval length>
Requires single Atomic CPU and fastmem.
<interval length> is in number of instructions.
2. Generate SimPoint analysis using SimPoint 3.2 from UCSD.
(SimPoint 3.2 not included with this flow.)
3. To take gem5 checkpoints based on SimPoint analysis, use the
following option:
--take-simpoint-checkpoint=<simpoint file path>,<weight file
path>,<interval length>,<warmup length>
<simpoint file> and <weight file> is generated by SimPoint analysis
tool from UCSD. SimPoint 3.2 format expected. <interval length> and
<warmup length> are in number of instructions.
4. To resume from gem5 SimPoint checkpoints, use the following option:
--restore-simpoint-checkpoint -r <N> --checkpoint-dir <simpoint
checkpoint path>
<N> is (SimPoint index + 1). E.g., "-r 1" will resume from SimPoint
#0.
|
|
Both options accept template which will, through python string formatting,
have "mem", "disk", and "script" values substituted in from the mdesc.
Additional values can be used on a case by case basis by passing them as
keyword arguments to the fillInCmdLine function. That makes it possible to
have specialized parameters for a particular ISA, for instance.
The first option lets you specify the template directly, and the other lets
you specify a file which has the template in it.
|
|
In the MI protocol, the master slave connection between the dma controller
and network was being set incorrectly. This patch corrects it.
|
|
|
|
This patch modifies se.py such that it can now use kvm cpu model.
|
|
Back out use of importlib to avoid implicitly creating
dependency on Python 2.7.
|
|
We can get the same result using importlib.
|
|
In fs.py the io port controller was being attached to the iobus multiple
times. This should be done only once. In se.py, the the option use_map
was being set which no longer exists.
|
|
Mwait works as follows:
1. A cpu monitors an address of interest (monitor instruction)
2. A cpu calls mwait - this loads the cache line into that cpu's cache.
3. The cpu goes to sleep.
4. When another processor requests write permission for the line, it is
evicted from the sleeping cpu's cache. This eviction is forwarded to the
sleeping cpu, which then wakes up.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
Ruby's functional accesses are not guaranteed to succeed as of now. While
this is not a problem for the protocols that are currently in the mainline
repo, it seems that coherence protocols for gpus rely on a backing store to
supply the correct data. The aim of this patch is to make this backing store
configurable i.e. it comes into play only when a particular option:
--access-backing-store is invoked.
The backing store has been there since M5 and GEMS were integrated. The only
difference is that earlier the system used to maintain the backing store and
ruby's copy was write-only. Sometime last year, we moved to data being
supplied supplied by ruby in SE mode simulations. And now we have patches on
the reviewboard, which remove ruby's copy of memory altogether and rely
completely on the system's memory to supply data. This patch adds back a
SimpleMemory member to RubySystem. This member is used only if the option:
access-backing-store is set to true. By default, the memory would not be
accessed.
|
|
This patch is the final in the series. The whole series and this patch in
particular were written with the aim of interfacing ruby's directory controller
with the memory controller in the classic memory system. This is being done
since ruby's memory controller has not being kept up to date with the changes
going on in DRAMs. Classic's memory controller is more up to date and
supports multiple different types of DRAM. This also brings classic and
ruby ever more close. The patch also changes ruby's memory controller to
expose the same interface.
|
|
Both ruby and the system used to maintain memory copies. With the changes
carried for programmed io accesses, only one single memory is required for
fs simulations. This patch sets the copy of memory that used to reside
with the system to null, so that no space is allocated, but address checks
can still be carried out. All the memory accesses now source and sink values
to the memory maintained by ruby.
|
|
regressions.
This changes the default ARM system to a Versatile Express-like system that supports
2GB of memory and PCI devices and updates the default kernels/file-systems for
AArch64 ARM systems (64-bit) to support up to 32GB of memory and PCI devices. Some
platforms that are no longer supported have been pruned from the configuration files.
In addition a set of 64-bit ARM regressions have been added to the regression system.
|
|
The bare-metal configuration option still configured memory with the old scheme
that no-longer works. This change unifies the code so there aren't any differences.
|
|
This patch adds the ability to load in config.ini files generated from
gem5 into another instance of gem5 built without Python configuration
support. The intended use case is for configuring gem5 when it is a
library embedded in another simulation system.
A parallel config file reader is also provided purely in Python to
demonstrate the approach taken and to provided similar functionality
for as-yet-unknown use models. The Python configuration file reader
can read both .ini and .json files.
C++ configuration file reading:
A command line option has been added for scons to enable C++ configuration
file reading: --with-cxx-config
There is an example in util/cxx_config that shows C++ configuration in action.
util/cxx_config/README explains how to build the example.
Configuration is achieved by the object CxxConfigManager. It handles
reading object descriptions from a CxxConfigFileBase object which
wraps a config file reader. The wrapper class CxxIniFile is provided
which wraps an IniFile for reading .ini files. Reading .json files
from C++ would be possible with a similar wrapper and a JSON parser.
After reading object descriptions, CxxConfigManager creates
SimObjectParam-derived objects from the classes in the (generated with this
patch) directory build/ARCH/cxx_config
CxxConfigManager can then build SimObjects from those SimObjectParams (in an
order dictated by the SimObject-value parameters on other objects) and bind
ports of the produced SimObjects.
A minimal set of instantiate-replacing member functions are provided by
CxxConfigManager and few of the member functions of SimObject (such as drain)
are extended onto CxxConfigManager.
Python configuration file reading (configs/example/read_config.py):
A Python version of the reader is also supplied with a similar interface to
CxxConfigFileBase (In Python: ConfigFile) to config file readers.
The Python config file reading will handle both .ini and .json files.
The object construction strategy is slightly different in Python from the C++
reader as you need to avoid objects prematurely becoming the children of other
objects when setting parameters.
Port binding also needs to be strictly in the same port-index order as the
original instantiation.
|
|
This patch moves code for instantiating a single memory controller from
the function config_mem() to a separate function. This is being done
so that memory controllers can be instantiated without assuming that
they will be attached to the system in a particular fashion.
|
|
|
|
This patch force IO device to be mapped to 0xC0000000-0xFFFF0000 by
reserve anything between the end of memory and 3GB if memory is less
than 3GB. It also statically bridge these address range to the IO bus,
which guaranty access to pci address space will pass though bridge to
iobus.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
This patch assign bus_id=0 to PCI bus and bus_id=1 to ISA bus for
X86 platform. Because PCI device get config space address using
Pc::calcPciConfigAddr() which requires "assert(bus==0)".
This fixes PCI interrupt routing and discovery on Linux.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
This patch changes the name of the Bus classes to XBar to better
reflect the actual timing behaviour. The actual instances in the
config scripts are not renamed, and remain as e.g. iobus or membus.
As part of this renaming, the code has also been clean up slightly,
making use of range-based for loops and tidying up some comments. The
only changes outside the bus/crossbar code is due to the delay
variables in the packet.
--HG--
rename : src/mem/Bus.py => src/mem/XBar.py
rename : src/mem/coherent_bus.cc => src/mem/coherent_xbar.cc
rename : src/mem/coherent_bus.hh => src/mem/coherent_xbar.hh
rename : src/mem/noncoherent_bus.cc => src/mem/noncoherent_xbar.cc
rename : src/mem/noncoherent_bus.hh => src/mem/noncoherent_xbar.hh
rename : src/mem/bus.cc => src/mem/xbar.cc
rename : src/mem/bus.hh => src/mem/xbar.hh
|
|
Add new DRAM_ROTATE mode to traffic generator.
This mode will generate DRAM traffic that rotates across
banks per rank, command types, and ranks per channel
The looping order is illustrated below:
for (ranks per channel)
for (command types)
for (banks per rank)
// Generate DRAM Command Series
This patch also adds the read percentage as an input argument to the
DRAM sweep script. If the simulated read percentage is 0 or 100, the
middle for loop does not generate additional commands. This loop is
used only when the read percentage is set to 50, in which case the
middle loop will toggle between read and write commands.
Modified sweep.py script, which generates DRAM traffic.
Added input arguments and support for new DRAM_ROTATE mode.
The script now has input arguments for:
1) Read percentage
2) Number of ranks
3) Address mapping
4) Traffic generator mode (DRAM or DRAM_ROTATE)
The default values are:
100% reads, 1 rank, RoRaBaCoCh address mapping, and DRAM traffic gen mode
For the DRAM traffic mode, added multi-rank support.
|
|
Instead of having code embedded in cpu model to do simpoint profiling use
the probes infrastructure to do it.
|
|
|
|
Change the default kernel for AArch64 and since it supports PCI devices
remove the hack that made it use CF. Unfortunately, there isn't really
a half-way here and we need to switch. Current users will get an error
message that the kernel isn't found and hopefully go download a new
kernel that supports PCI.
|
|
This eliminates some default devices and adds in helper functions
to connect the devices defined here to associate with the proper
clock domains.
|
|
As highlighed on the mailing list gem5's writeback modeling can impact
performance. This patch removes the limitation on maximum outstanding issued
instructions, however the number that can writeback in a single cycle is still
respected in instToCommit().
|
|
This patch adds basic functionality to quickly visualise the output
from the DRAM efficiency script. There are some unfortunate hacks
needed to communicate the needed information from one script to the
other, and we fall back on (ab)using the simout to do this.
As part of this patch we also trim the efficiency sweep to stop at 512
bytes as this should be sufficient for all forseeable DRAMs.
|
|
This patch is the final patch in a series of patches. The aim of the series
is to make ruby more configurable than it was. More specifically, the
connections between controllers are not at all possible (unless one is ready
to make significant changes to the coherence protocol). Moreover the buffers
themselves are magically connected to the network inside the slicc code.
These connections are not part of the configuration file.
This patch makes changes so that these connections will now be made in the
python configuration files associated with the protocols. This requires
each state machine to expose the message buffers it uses for input and output.
So, the patch makes these buffers configurable members of the machines.
The patch drops the slicc code that usd to connect these buffers to the
network. Now these buffers are exposed to the python configuration system
as Master and Slave ports. In the configuration files, any master port
can be connected any slave port. The file pyobject.cc has been modified to
take care of allocating the actual message buffer. This is inline with how
other port connections work.
|
|
This patch fixes scripts related to ruby by adding the ruby clock domain.
Now the L1 controllers and the Sequencer shares the cpu clock domain,
while the rest of the components use the ruby clock domain.
Before this patch, running simulations with the cpu clock set at 2GHz or
1GHz will output the same time results and could distort power measurements.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
This patch fixes the cache latency in mem test which is split into two params,
hit and response latency as per BaseCache.
|
|
the Cortex-A15 has a random replacement policy for its L2 cache. see the
Cortex-A15 Technical Reference Manual 1.7 About the L2 memory system. this
patch makes the PseudoLRU tags the default for the ARM O3 CPU's L2 cache.
|
|
This patch contains a new CPU model named `Minor'. Minor models a four
stage in-order execution pipeline (fetch lines, decompose into
macroops, decompose macroops into microops, execute).
The model was developed to support the ARM ISA but should be fixable
to support all the remaining gem5 ISAs. It currently also works for
Alpha, and regressions are included for ARM and Alpha (including Linux
boot).
Documentation for the model can be found in src/doc/inside-minor.doxygen and
its internal operations can be visualised using the Minorview tool
utils/minorview.py.
Minor was designed to be fairly simple and not to engage in a lot of
instruction annotation. As such, it currently has very few gathered
stats and may lack other gem5 features.
Minor is faster than the o3 model. Sample results:
Benchmark | Stat host_seconds (s)
---------------+--------v--------v--------
(on ARM, opt) | simple | o3 | minor
| timing | timing | timing
---------------+--------+--------+--------
10.linux-boot | 169 | 1883 | 1075
10.mcf | 117 | 967 | 491
20.parser | 668 | 6315 | 3146
30.eon | 542 | 3413 | 2414
40.perlbmk | 2339 | 20905 | 11532
50.vortex | 122 | 1094 | 588
60.bzip2 | 2045 | 18061 | 9662
70.twolf | 207 | 2736 | 1036
|
|
the branch predictor used in the Cortex-A15 is a bi-mode style predictor,
see:
http://arm.com/files/pdf/at-exploring_the_design_of_the_cortex-a15.pdf
and
http://nvidia.com/docs/IO/116757/NVIDIA_Quad_a15_whitepaper_FINALv2.pdf
this patch makes the bi-mode predictor the default for the ARM O3 CPU.
|
|
in makeDualRoot() the etherlink interfaces are set using the tsunami interface
however, they are set again a few lines later based on whether or not the system
is a realview or tsunami system; the original assignment is always overwritten
or there will be a fatal. this seems like an artifact from when tsunami was the
only type of system capable of running with the dual option.
|
|
This patch bumps the bus clock speed such that the interconnect does
not become a bottleneck with a DDR4-2400-x64 DRAM delivering 19.2
GByte/s theoretical max.
|
|
It is not in use and not required as such.
|
|
|
|
Adds the parameter --num-work-ids to Options.py and reads the parameter
into the System params in Simulation.py. This parameter enables setting
the number of possible work items to different than 16. Support for this
parameter already exists in src/sim/System.py, so this changeset only
affects the Python config files.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
A recent changeset altered the default memory class to DRAMCtrl. In se mode,
ruby uses the physical memory to check if a given address is within the bounds
of the physical memory. SimpleMemory is enough for this. Moreover,
SimpleMemory does not check whether it is connected or not, something which
DRAMCtrl does.
|
|
This patch renames the not-so-simple SimpleDRAM to a more suitable
DRAMCtrl. The name change is intended to ensure that we do not send
the wrong message (although the "simple" in SimpleDRAM was originally
intended as in cleverly simple, or elegant).
As the DRAM controller modelling work is being presented at ISPASS'14
our hope is that a broader audience will use the model in the future.
--HG--
rename : src/mem/SimpleDRAM.py => src/mem/DRAMCtrl.py
rename : src/mem/simple_dram.cc => src/mem/dram_ctrl.cc
rename : src/mem/simple_dram.hh => src/mem/dram_ctrl.hh
|
|
Make the default memory type DDR3-1600 x64, and use the open-adaptive
page policy. This change is aiming to ensure that users by default are
using a realistic memory system.
|
|
This patch adds a configuration that simplifies evaluation of DRAM
controller configurations by automating a sweep of stride size and
bank parallelism. It works in a rather unconventional way, as it needs
to print the traffic generator stimuli based on the memory
organisation. Hence, it starts by configuring the memory, then it
prints a traffic-generator config file, and loads it.
The resulting stats have one period per data point, identified by the
stride size, and the number of banks being used.
|
|
This patch adds the row bits to the name of the address mapping
schemes to make it more clear that all the current schemes places the
row bits as the most significant bits.
|
|
This helps in configuring the network interfaces from the python script and
these objects no longer rely on the network object for the timing information.
|
