Age | Commit message (Collapse) | Author |
|
|
|
|
|
The x87 FPU supports three floating point formats: 32-bit, 64-bit, and
80-bit floats. The current gem5 implementation supports 32-bit and
64-bit floats, but only works correctly for 64-bit floats. This
changeset fixes the 32-bit float handling by correctly loading and
rounding (using truncation) 32-bit floats instead of simply truncating
the bit pattern.
80-bit floats are loaded by first loading the 80-bits of the float to
two temporary integer registers. A micro-op (cvtint_fp80) then
converts the contents of the two integer registers to the internal FP
representation (double). Similarly, when storing an 80-bit float,
there are two conversion routines (ctvfp80h_int and cvtfp80l_int) that
convert an internal FP register to 80-bit and stores the upper 64-bits
or lower 32-bits to an integer register, which is the written to
memory using normal integer stores.
|
|
X87 store instructions typically loads and pops the top value of the
stack and stores it in memory. The current implementation pops the
stack at the same time as the floating point value is loaded to a
temporary register. This will corrupt the state of the x87 stack if
the store fails. This changeset introduces a pop87 micro-instruction
that pops the stack and uses this instruction in the affected
macro-instructions to pop the stack after storing the value to memory.
|
|
The x87 FPU on x86 supports extended floating point. We currently
handle all floating point on x86 as double and don't support 80-bit
loads/stores. This changeset add a utility function to load and
convert 80-bit floats to doubles (loadFloat80) and another function to
store doubles as 80-bit floats (storeFloat80). Both functions use
libfputils to do the conversion in software. The functions are
currently not used, but are required to handle floating point in KVM
and to properly support all x87 loads/stores.
|
|
Add support for extracting the first 6 64-bit integer argumements to a
function call in X86ISA::getArgument().
|
|
This changeset adds the convX87XTagsToTags() and convX87TagsToXTags()
which convert between the tag formats in the FTW register and the
format used in the xsave area. The conversion from to the x87 FTW
representation is currently loses some information since it does not
reconstruct the valid/zero/special flags which are not included in the
xsave representation.
|
|
This patch allows the KVM CPU module to initialize it's MSRs by
enumerating the MSRs in the gem5 x86 implementation.
|
|
In order to support hardware virtualization, we need to be able to
check if there are any interrupts pending irregardless of the
rflags.intf value. This changeset adds the checkInterruptsRaw() method
to the x86 interrupt control. It returns true if there are pending
interrupts that can be delivered as soon as the CPU is ready for
interrupt delivery.
|
|
This patch allows a hardware virtualized CPU to discover which interrupt
to deliver to the guest.
|
|
This patch makes it possible to once again build gem5 without any
ISA. The main purpose is to enable work around the interconnect and
memory system without having to build any CPU models or device models.
The regress script is updated to include the NULL ISA target. Currently
no regressions make use of it, but all the testers could (and perhaps
should) transition to it.
--HG--
rename : build_opts/NOISA => build_opts/NULL
rename : src/arch/noisa/SConsopts => src/arch/null/SConsopts
rename : src/arch/noisa/cpu_dummy.hh => src/arch/null/cpu_dummy.hh
rename : src/cpu/intr_control.cc => src/cpu/intr_control_noisa.cc
|
|
This patch moves the system virtual port proxy to the Alpha system
only to make the resurrection of the NOISA slightly less
painful. Alpha is the only ISA that is actually using it.
|
|
This patch adds a check to the quiesce operation to ensure that the
CPU does not suspend itself when there are unmasked interrupts
pending. Without this patch there are corner cases when the CPU gets
an interrupt before the quiesce is executed and then never wakes up
again.
|
|
This patch adds checkpointing support to x86 tlb. It upgrades the
cpt_upgrader.py script so that previously created checkpoints can
be updated. It moves the checkpoint version to 6.
|
|
This patch removes the notion of a peer block size and instead sets
the cache line size on the system level.
Previously the size was set per cache, and communicated through the
interconnect. There were plenty checks to ensure that everyone had the
same size specified, and these checks are now removed. Another benefit
that is not yet harnessed is that the cache line size is now known at
construction time, rather than after the port binding. Hence, the
block size can be locally stored and does not have to be queried every
time it is used.
A follow-on patch updates the configuration scripts accordingly.
|
|
Instead of relying on derived classes explicitly assigning
to the BasicPioDevice pioSize field, require them to pass
a size value in to the constructor.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
PciDev and IntDev stuck out as the only device classes that
ended in 'Dev' rather than 'Device'. This patch takes care
of that inconsistency.
Note that you may need to delete pre-existing files matching
build/*/python/m5/internal/param_* as scons does not pick up
indirect dependencies on imported python modules when generating
params, and the PciDev -> PciDevice rename takes place in a
file (dev/Device.py) that gets imported quite a bit.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
A couple of devices that have single fixed memory mapped regions
were not derived from BasicPioDevice, when that's exactly
the functionality that BasicPioDevice provides. This patch
gets rid of a little bit of redundant code by making those
devices actually do so.
Also fixed the weird case of X86ISA::Interrupts, where
the class already did derive from BasicPioDevice but
didn't actually use all the features it could have.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
This patch adds the notion of source- and derived-clock domains to the
ClockedObjects. As such, all clock information is moved to the clock
domain, and the ClockedObjects are grouped into domains.
The clock domains are either source domains, with a specific clock
period, or derived domains that have a parent domain and a divider
(potentially chained). For piece of logic that runs at a derived clock
(a ratio of the clock its parent is running at) the necessary derived
clock domain is created from its corresponding parent clock
domain. For now, the derived clock domain only supports a divider,
thus ensuring a lower speed compared to its parent. Multiplier
functionality implies a PLL logic that has not been modelled yet
(create a separate clock instead).
The clock domains should be used as a mechanism to provide a
controllable clock source that affects clock for every clocked object
lying beneath it. The clock of the domain can (in a future patch) be
controlled by a handler responsible for dynamic frequency scaling of
the respective clock domains.
All the config scripts have been retro-fitted with clock domains. For
the System a default SrcClockDomain is created. For CPUs that run at a
different speed than the system, there is a seperate clock domain
created. This domain incorporates the CPU and the associated
caches. As before, Ruby runs under its own clock domain.
The clock period of all domains are pre-computed, such that no virtual
functions or multiplications are needed when calling
clockPeriod. Instead, the clock period is pre-computed when any
changes occur. For this to be possible, each clock domain tracks its
children.
|
|
The current implementation of the x87 never updates the x87 tag
word. This is currently not a big issue since the simulated x87 never
checks for stack overflows, however this becomes an issue when
switching between a virtualized CPU and a simulated CPU. This
changeset adds support, which is enabled by default, for updating the
tag register to every floating point microop that updates the stack
top using the spm mechanism.
The new tag words is generated by the helper function
X86ISA::genX87Tags(). This function is currently limited to flagging a
stack position as valid or invalid and does not try to distinguish
between the valid, zero, and special states.
|
|
This changeset actually fixes two issues:
* The lfpimm instruction didn't work correctly when applied to a
floating point constant (it did work for integers containing the
bit string representation of a constant) since it used
reinterpret_cast to convert a double to a uint64_t. This caused a
compilation error, at least, in gcc 4.6.3.
* The instructions loading floating point constants in the x87
processor didn't work correctly since they just stored a truncated
integer instead of a double in the floating point register. This
changeset fixes the old microcode by using lfpimm instruction
instead of the limm instructions.
|
|
|
|
This patch allows the default x86 state to be used when by CPUs that
use hardware virtualization.
|
|
The current implementation of fprem simply does an fmod and doesn't
simulate any of the iterative behavior in a real fprem. This isn't
normally a problem, however, it can lead to problems when switching
between CPU models. If switching from a real CPU in the middle of an
fprem loop to a simulated CPU, the output of the fprem loop becomes
correupted. This changeset changes the fprem implementation to work
like the one on real hardware.
|
|
The rflags register is spread across several different registers. Most
of the flags are stored in MISCREG_RFLAGS, but some are stored in
microcode registers. When accessing RFLAGS, we need to reconstruct it
from these registers. This changeset adds two functions,
X86ISA::getRFlags() and X86ISA::setRFlags(), that take care of this
magic.
|
|
This changeset fixes two problems in the FABS and FCHS
implementation. First, the ISA parser expects the assignment in
flag_code to be a pure assignment and not an and-assignment, which
leads to the isa_parser omitting the misc reg update. Second, the FCHS
and FABS macro-ops don't set the SetStatus flag, which means that the
default micro-op version, which doesn't update FSW, is executed.
|
|
The TSC value stored in MISCREG_TSC is actually just an offset from
the current CPU cycle to the actual TSC value. Writes with
side-effects to the TSC subtract the current cycle count before
storing the new value, while reads add the current cycle count. When
switching CPUs, the current value is copied without side-effects. This
works as long as the source and the destination CPUs have the same
clock frequencies. The TSC will jump, sometimes backwards, if they
have different clock frequencies. Most OSes assume the TSC to be
monotonic and break when this happens.
This changeset makes sure that the TSC is copied with side-effects to
ensure that the offset is updated to match the new CPU.
|
|
in the TLB
Some architectures (currently only x86) require some fixing-up of
physical addresses after a normal address translation. This is usually
to remap devices such as the APIC, but could be used for other memory
mapped devices as well. When running the CPU in a using hardware
virtualization, we still need to do these address fix-ups before
inserting the request into the memory system. This patch moves this
patch allows that code to be used by such CPUs without doing full
address translations.
|
|
This is the x86 version of the ARM changeset baa17ba80e06. In case an
instruction has been squashed by the o3 cpu, this patch allows page
table walker to avoid carrying out a pending translation that the
instruction requested for.
|
|
Currently call and return instructions are marked as IsCall and IsReturn. Thus, the
branch predictor does not use RAS for these instructions. Similarly, the number of
function calls that took place is recorded as 0. This patch marks these instructions
as they should be.
|
|
Currently all the integer microops are marked as IntAluOp and the floating
point microops are marked as FloatAddOp. This patch adds support for marking
different microops differently. Now IntMultOp, IntDivOp, FloatDivOp,
FloatMultOp, FloatCvtOp, FloatSqrtOp classes will be used as well. This will
help in providing different latencies for different op class.
|
|
|
|
The vsyscall address for gettimeofday is 0xffffffffff600000ul. The offset
therefore should be 0x0 instead of 0x410. This can be cross checked with
the file sysdeps/unix/sysv/linux/x86_64/gettimeofday.c in source of glibc.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
The 'lret' instruction reloads instruction pointer and code segment from the
stack and then pops them. But the popping part is missing from the current
implementation. This caused incorrect behavior in some code related to the
Fiasco OS. Microops are being added to rectify the behavior of the instruction.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
Add the method checkRaw to ArmISA::Interrupts. This method can be used
to query the raw state (ignoring CPSR masks) of an interrupt. It is
primarily intended for hardware virtualized CPUs.
|
|
Add the options 'panic_on_panic' and 'panic_on_oops' to the
LinuxArmSystem SimObject. When these option are enabled, the simulator
panics when the guest kernel panics or oopses. Enable panic on panic
and panic on oops in ARM-based test cases.
|
|
This changeset adds support for forwarding arguments to the PC
event constructors to following methods:
addKernelFuncEvent
addFuncEvent
Additionally, this changeset adds the following helper method to the
System base class:
addFuncEventOrPanic - Hook a PCEvent to a symbol, panic on failure.
addKernelFuncEventOrPanic - Hook a PCEvent to a kernel symbol, panic
on failure.
System implementations have been updated to use the new functionality
where appropriate.
|
|
This patch adds a missing flag to the ldr_ret_uop microop instruction.
The flag is added when the instruction is used, not directly in the
constructor of the instruction.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>"
|
|
It is possible that operating system wants to shutdown the
lapic timer by writing timer's initial count to 0. This patch
adds a check that the timer event is only scheduled if the
count is 0.
The patch also converts few of the panics related to the keyboard
to warnings since we are any way not interested in simulating the
keyboard.
|
|
This patch implements ftan, fprem, fyl2x, fld* floating-point instructions.
|
|
This patch fixes an issue related to the table walker recycling
packets that still have a bus delay that is not accounted for. For
now, we simply ignore the values and reset them to zero.
|
|
accidently branches.
|
|
This patch fixes the warnings that clang3.2svn emit due to the "-Wall"
flag. There is one case of an uninitialised value in the ARM neon ISA
description, and then a whole range of unused private fields that are
pruned.
|
|
This patch enables warnings for missing declarations. To avoid issues
with SWIG-generated code, the warning is only applied to non-SWIG
code.
|
|
Fix the ISA startup warnings
|
|
A derived function with a different signature than a base class
function will result in the base class function of the same name being
hidden. The parameter list and return type for the member function in
the derived class must match those of the member function in the base
class, otherwise the function in the derived class will hide the
function in the base class and no polymorphic behaviour will occur.
This patch addresses these warnings by ensuring a unique function name
to avoid (unintentionally) hiding any functions.
|
|
This patch adds a warning for missing field initializers for both gcc
and clang, and addresses the warnings that were generated.
|
|
This patch address the most important name shadowing warnings (as
produced when using gcc/clang with -Wshadow). There are many
locations where constructor parameters and function parameters shadow
local variables, but these are left unchanged.
|
|
This patch moves the 16x APIC clock divider to the Python code to
avoid the post-instantiation modifications to the clock. The x86 APIC
was the only object setting the clock after creation time and this
required some custom functionality and configuration. With this patch,
the clock multiplier is moved to the Python code and the objects are
instantiated with the appropriate clock.
|