| Age | Commit message (Collapse) | Author |
|---|
|
When a table walk is initiated by the fetch stage, the CPU can
potentially move to the idle state and never wake up.
The fetch stage must call cpu->wakeCPU() when a translation completes
(in finishTranslation()).
|
|
occurs.
This change fixes an issue where a DTLB fault occurs and redirects fetch to
handle the fault and the ITLB requires a walk which delays translation. In this
case the status of the cpu isn't updated appropriately, and an additional
instruction fetch occurs. Eventually this hits an assert as multiple instruction
fetches are occuring in the system and when the second one returns the
processor is in the wrong state.
Some asserts below are removed because it was always true (typo) and the state
after the initiateAcc() the processor could be in any valid state when a
d-side fault occurs.
|
|
Some ISAs (like ARM) relies on hardware page table walkers. For those ISAs,
when a TLB miss occurs, initiateTranslation() can return with NoFault but with
the translation unfinished.
Instructions experiencing a delayed translation due to a hardware page table
walk are deferred until the translation completes and kept into the IQ. In
order to keep track of them, the IQ has been augmented with a queue of the
outstanding delayed memory instructions. When their translation completes,
instructions are re-executed (only their initiateAccess() was already
executed; their DTB translation is now skipped). The IEW stage has been
modified to support such a 2-pass execution.
|
|
|
|
In sendSplitData, keep a pointer to the senderState that may be updated after
the call to handle*Packet. This way, if the receiver updates the packet
senderState, it can still be accessed in sendSplitData.
|
|
Updated patches from Rick Strong's set that modify performance counters for
McPAT
|
|
Maintain all information about an instruction's fault in the DynInst object rather
than any cpu-request object. Also, if there is a fault during the execution stage
then just save the fault inside the instruction and trap once the instruction
tries to graduate
|
|
not taken delay slots were not being advanced correctly to pc+8, so for those ISAs
we 'advance()' the pcstate one more time for the desired effect
|
|
Give fetch unit it's own parameterizable fetch buffer to read from. Very inefficient
(architecturally and in simulation) to continually fetch at the granularity of the
wordsize. As expected, the number of fetch memory requests drops dramatically
|
|
no need to have separate function name findSplitRequest, just overload the function
|
|
instead of having one cache-unit class be responsible for both data and code
accesses, separate code that is just for fetch in it's own derived class off the
original base class. This makes the code easier to manage as well as handle
future cases of special fetch handling
|
|
set the request to false when the cache port blocks so we dont deadlock.
also, comment out the outstanding address list sanity check for now.
|
|
allow the user to specify how many instructions a pipeline stage can process
on any given cycle (stageWidth...i.e.bandwidth) by setting the parameter through
the python interface rather than compile the code after changing the *.cc file.
(we always had the parameter there, but still used the static 'ThePipeline::StageWidth'
instead)
-
Since StageWidth is now dynamically defined, change the interstage communication
structure to use a vector and get rid of array and array handling index (toNextStageIndex)
since we can just make calls to the list for the same information
|
|
Only execute (resolve) one branch per cycle because handling more than one is
a little more complicated
|
|
use skidbuffer as only location for instructions between stages. before,
we had the insts queue from the prior stage and the skidbuffer for the
current stage, but that gets confusing and this consolidation helps
when handling squash cases
|
|
manage insertion and deletion like a queue but will need
access to internal elements for future changes
Currently, skidbuffer manages any instruction that was
in a stage but could not complete processing, however
we will want to manage all blocked instructions (from prev stage
and from cur. stage) in just one buffer.
|
|
Previous code was marking CPU activity on almost every cycle due to a bug in
tracking the status of pipeline stages. This disables the CPU from sleeping
on long latency stalls and increases simulation time
|
|
--HG--
rename : src/sim/fault.hh => src/sim/fault_fwd.hh
|
|
This makes sure that the address ranges requested for caches and uncached ports
don't conflict with each other, and that accesses which are always uncached
(message signaled interrupts for instance) don't waste time passing through
caches.
|
|
|
|
Small L1 caches are connected to the TLB walkers when caches are used. This
allows them to participate in the coherence protocol properly.
|
|
|
|
|
|
Without this change 0 is always used for the youngest sequence number if
a squash occured and the ROB was empty (E.g. an instruction is marked
serializeAfter or a fetch stall prevents other instructions from issuing).
Using 0 there is a race to rename where an instruction that committed the
same cycle as the squashing instruction can have it's renamed state undone
by the squash using sequence number 0.
|
|
I'm not positive this is the correct fix, but it's working right now.
Either we need to do something like this, prevent the misc reg from being renamed at all,
or there something else going on. We need to find the root cause as to why
this is only a problem sometimes.
|
|
|
|
The squash inside the fetch unit should not attempt to remove them from the
branch predictor as non-control instructions are not pushed into the predictor.
|
|
This patch prevents the prefetch being added to the instCommit queue twice.
|
|
|
|
|
|
When this condition occurs the cpu should restart the fetch stage to fetch from
the original execution path. Fault handling in the commit stage is cleaned up a
little bit so the control flow is simplier. Finally, if an instruction is being
used to carry a fault it isn't executed, so the fault propagates appropriately.
|
|
the current code was using incorrect dummy instruction in interrupts function
|
|
This step makes it easy to replace the accessor functions
(which still access a global variable) with ones that access
per-thread curTick values.
|
|
There were several copies of similar functions that looked
like they all replicated reschedule(), so I replaced them
with direct calls. Keeping this separate from the previous
cset since there may be some subtle functional differences
if the code ever reschedules an event that is scheduled but
not squashed (though none were detected in the regressions).
|
|
Events need to be scheduled on the queue assigned
to the SimObject, not on the global queue (which
should be going away).
Also cleaned up a number of redundant expressions
that made the code unnecessarily verbose.
|
|
These files really aren't general enough to belong in src/base.
This patch doesn't reorder include lines, leaving them unsorted
in many cases, but Nate's magic script will fix that up shortly.
--HG--
rename : src/base/sched_list.hh => src/cpu/sched_list.hh
rename : src/base/timebuf.hh => src/cpu/timebuf.hh
|
|
Ran all the source files through 'perl -pi' with this script:
s|\s*(};?\s*)?/\*\s*(end\s*)?namespace\s*(\S+)\s*\*/(\s*})?|} // namespace $3|;
s|\s*};?\s*//\s*(end\s*)?namespace\s*(\S+)\s*|} // namespace $2\n|;
s|\s*};?\s*//\s*(\S+)\s*namespace\s*|} // namespace $1\n|;
Also did a little manual editing on some of the arch/*/isa_traits.hh files
and src/SConscript.
|
|
file. These statements have been replaced with warn(), panic() and fatal() defined in src/base/misc.hh
|
|
|
|
|
|
The store queue doesn't need to be ISA specific and architectures can
frequently store more than an int registers worth of data. A 128 bits seems
more common, but even 256 bits may be appropriate. Pretty much anything less
than a cache line size is buildable.
|
|
For SPARC ASIs are added to the ExtMachInst. If the ASI is changed simply
marking the instruction as Serializing isn't enough beacuse that only
stops rename. This provides a mechanism to squash all the instructions
and refetch them
|
|
until commit.
ARM instructions updating cumulative flags (ARM FP exceptions and saturation
flags) are not serialized.
Added aliases for ARM FP exceptions and saturation flags in FPSCR. Removed
write accesses to the FP condition codes for most ARM VFP instructions: only
VCMP and VCMPE instructions update the FP condition codes. Removed a potential
cause of seg. faults in the O3 model for NEON memory macro-ops (ARM).
|
|
|
|
|
|
This patch developed by Nilay Vaish converts all the old GEMS-style ruby
debug calls to the appropriate M5 debug calls.
|
|
|
|
|
|
This change makes O3 flatten floating point destination registers, and also
fixes misc register flattening so that it's correctly repositioned relative to
the resized regions for integer and floating point indices.
It also fixes some overly long lines.
|
|
|
