| Age | Commit message (Collapse) | Author |
|---|
|
readBytes and writeBytes had the word "bytes" in their names because they
accessed blobs of bytes. This distinguished them from the read and write
functions which handled higher level data types. Because those functions don't
exist any more, this change renames readBytes and writeBytes to more general
names, readMem and writeMem, which reflect the fact that they are how you read
and write memory. This also makes their names more consistent with the
register reading/writing functions, although those are still read and set for
some reason.
|
|
|
|
This patch rpovides functional access support in Ruby. Currently only
the M5Port of RubyPort supports functional accesses. The support for
functional through the PioPort will be added as a separate patch.
|
|
|
|
this will safeguard future code from trying to remove
from the list twice. That code wouldnt break but would
waste time.
|
|
|
|
|
|
handle them like we do in FS mode, by blocking the TLB until the fault
is handled by the fault->invoke()
|
|
|
|
|
|
|
|
implement clearfetchbufferfunction
extend predecoder to use multiple threads and clear those on trap
|
|
this will make sure we get the correct view of a FP register
|
|
|
|
The DTB expects the correct PC in the ThreadContext
but how if the memory accesses are speculative? Shouldn't
we send along the requestor's PC to the translate functions?
|
|
including IPR accesses and store-conditionals. These class of instructions will not
execute correctly in a superscalar machine
|
|
if a faulting instruction reaches an execution unit,
then ignore it and pass it through the pipeline.
Once we recognize the fault in the graduation unit,
dont allow a second fault to creep in on the same cycle.
|
|
handle "snoop" port registration as well as functional
port setup for FS mode
|
|
use a dummy instruction to facilitate the squash after
the interrupts trap
|
|
Before graduating an instruction, explicitly check fault
by making the fault check it's own separate command
that can be put on an instruction schedule.
|
|
|
|
|
|
make syscall a SE mode only functionality
copy over basic FS functions (hwrei) to make FS compile
|
|
speculative load/store pipelines can reenable this
|
|
calculate blocks in use for the fetch buffer to figure out how many total blocks
are pending
|
|
Sharing the FP value w/the integer values was giving inconsistent results esp. when
their is a 32-bit integer register matched w/a 64-bit float value
|
|
define a syscallContext to schedule the syscall and then use syscall() to actually perform the action
|
|
segfault was caused by squashed multiply thats in the process of an event.
use isProcessing flag to handle this and cleanup the MDU code
|
|
|
|
remove events in the resource pool that can be called from the CPU event, since the CPU
event is scheduled at the same time at the resource pool event.
----
Also, match the resPool event function names to the cpu event function names
----
|
|
once a ST is sent off, it's OK to keep processing, however it's a little more
complicated to handle the packet acknowledging the store is completed
|
|
once a ST is sent off, it's OK to keep processing, however it's a little more
complicated to handle the packet acknowledging the store is completed
|
|
also, cleanup comments for gem5.fast compilation
|
|
dont treat read() and write() fields as mut. exclusive
|
|
only update BTB on a taken branch and update branch predictor w/pcstate from instruction
---
only pay attention to branch predictor updates if the the inst. is in fact a branch
|
|
define separate priority resource pool squash and graduate events
|
|
|
|
this causes forwarding a bad value register value
|
|
|
|
|
|
use it in reg. dep. tracking
|
|
dont use offset to calculate this but rather an enum
that can be updated
|
|
|
|
|
|
implement a clean interface to handle branch misprediction and eventually all pipeline
flushing
|
|
The DynInst was not performing the host-to-guest translation
which ended up breaking stores for SPARC
|
|
formerly, this was implicit when you accessed the execution unit
or the use-def unit but it's better that this just be something
that a user can specify.
|
|
|
|
add find and end functions for inst. schedules
that can search by stage number
|
|
keep stats for int/float reg file usage instead
of aggregating across reg file types
|
