| Age | Commit message (Collapse) | Author |
|---|
|
This also allows checkpointing of a Kvm GIC via the Pl390 model.
Change-Id: Ic85d81cfefad630617491b732398f5e6a5f34c0b
Reviewed-by: Andreas Sandberg <andreas.sandberg@arm.com>
Reviewed-on: https://gem5-review.googlesource.com/2444
Maintainer: Andreas Sandberg <andreas.sandberg@arm.com>
Reviewed-by: Weiping Liao <weipingliao@google.com>
|
|
This change adds the ability to print a message at intervals
of committed instruction count to indicate progress in the
trace replay.
Change-Id: I8363502354c42bfc52936d2627986598b63a5797
Reviewed-by: Rekai Gonzalez Alberquilla <rekai.gonzalezalberquilla@arm.com>
Signed-off-by: Andreas Sandberg <andreas.sandberg@arm.com>
Reviewed-on: https://gem5-review.googlesource.com/2321
Reviewed-by: Jason Lowe-Power <jason@lowepower.com>
|
|
simulations
Modifies the clone system call and adds execve system call. Requires allowing
processes to steal thread contexts from other processes in the same system
object and the ability to detach pieces of process state (such as MemState)
to allow dynamic sharing.
|
|
This changeset adds functionality that allows system calls to retry without
affecting thread context state such as the program counter or register values
for the associated thread context (when system calls return with a retry
fault).
This functionality is needed to solve problems with blocking system calls
in multi-process or multi-threaded simulations where information is passed
between processes/threads. Blocking system calls can cause deadlock because
the simulator itself is single threaded. There is only a single thread
servicing the event queue which can cause deadlock if the thread hits a
blocking system call instruction.
To illustrate the problem, consider two processes using the producer/consumer
sharing model. The processes can use file descriptors and the read and write
calls to pass information to one another. If the consumer calls the blocking
read system call before the producer has produced anything, the call will
block the event queue (while executing the system call instruction) and
deadlock the simulation.
The solution implemented in this changeset is to recognize that the system
calls will block and then generate a special retry fault. The fault will
be sent back up through the function call chain until it is exposed to the
cpu model's pipeline where the fault becomes visible. The fault will trigger
the cpu model to replay the instruction at a future tick where the call has
a chance to succeed without actually going into a blocking state.
In subsequent patches, we recognize that a syscall will block by calling a
non-blocking poll (from inside the system call implementation) and checking
for events. When events show up during the poll, it signifies that the call
would not have blocked and the syscall is allowed to proceed (calling an
underlying host system call if necessary). If no events are returned from the
poll, we generate the fault and try the instruction for the thread context
at a distant tick. Note that retrying every tick is not efficient.
As an aside, the simulator has some multi-threading support for the event
queue, but it is not used by default and needs work. Even if the event queue
was completely multi-threaded, meaning that there is a hardware thread on
the host servicing a single simulator thread contexts with a 1:1 mapping
between them, it's still possible to run into deadlock due to the event queue
barriers on quantum boundaries. The solution of replaying at a later tick
is the simplest solution and solves the problem generally.
|
|
A KVM VM is typically a child of the System object already, but for
solving future issues with configuration graph resolution, the most
logical way to keep track of this object is for it to be an actual
parameter of the System object.
Change-Id: I965ded22203ff8667db9ca02de0042ff1c772220
Reviewed-by: Andreas Sandberg <andreas.sandberg@arm.com>
|
|
Used cppclean to help identify useless includes and removed them. This
involved erroneously included headers, but also cases where forward
declarations could have been used rather than a full include.
|
|
|
|
The headers declared in export_method_cxx_predecls are redundant since a
SimObject's main header is automatically included.
Change-Id: Ied9e84630b36960e54efe91d16f8c66fba7e0da0
Signed-off-by: Andreas Sandberg <andreas.sandberg@arm.com>
Reviewed-by: Curtis Dunham <curtis.dunham@arm.com>
Reviewed-by: Joe Gross <joseph.gross@amd.com>
Reviewed-by: Jason Lowe-Power <jason@lowepower.com>
|
|
This patch implements an L-TAGE predictor, based on André Seznec's code
available from CBP-2
(http://hpca23.cse.tamu.edu/taco/camino/cbp2/cbp-src/realistic-seznec.h).
Signed-off-by Jason Lowe-Power <jason@lowepower.com>
|
|
The Minor and o3 cpu models share the branch prediction
code. Minor relies on the BPredUnit::squash() function
to update the branch predictor tables on a branch mispre-
diction. This is fine because Minor executes in-order, so
the update is on the correct path. However, this causes the
branch predictor to be updated on out-of-order branch
mispredictions when using the o3 model, which should not
be the case.
This patch guards against speculative update of the branch
prediction tables. On a branch misprediction, BPredUnit::squash()
calls BpredUnit::update(..., squashed = true). The underlying
branch predictor tests against the value of squashed. If it is
true, it restores any speculatively updated internal state
it might have (e.g., global/local branch history), then returns.
If false, it updates its prediction tables. Previously, exist-
ing predictors did not test against the "squashed" parameter.
To accomodate for this change, the Minor model must now call
BPredUnit::squash() then BPredUnit::update(..., squashed = false)
on branch mispredictions. Before, calling BpredUnit::squash()
performed the prediction tables update.
The effect is a slight MPKI improvement when using the o3
model. A further patch should perform the same modifications
for the indirect target predictor and BTB (less critical).
Signed-off-by: Jason Lowe-Power <jason@lowepower.com>
|
|
The tournament predictor is presented as doing speculative
update of the global history and non-speculative update
of the local history used to generate the branch prediction.
However, the code does speculative update of both histories.
Signed-off-by: Jason Lowe-Power <jason@lowepower.com>
|
|
The target of taken conditional direct branches does not
need to be resolved in IEW: the target can be computed at
decode, usually using the decoded instruction word and the PC.
The higher-than-necessary penalty is taken only on conditional
branches that are predicted taken but miss in the BTB. Thus,
this is mostly inconsequential on IPC if the BTB is big/associative
enough (fewer capacity/conflict misses). Nonetheless, what gem5
simulates is not representative of how conditional branch targets
can be handled.
Signed-off-by: Jason Lowe-Power <jason@lowepower.com>
|
|
cachePorts currently constrains the number of store packets written to the
D-Cache each cycle), but loads currently affect this variable. This leads
to unexpected congestion (e.g., setting cachePorts to a realistic 1 will
in fact allow a store to WB only if no loads have accessed the D-Cache
this cycle). In the absence of arbitration, this patch decouples how many
loads can be done per cycle from how many stores can be done per cycle.
Signed-off-by: Jason Lowe-Power <jason@lowepower.com>
|
|
Previously all traffic generators would use the same value for write
requests. With this change traffic generators use their master id as
the payload of write requests making them more useful for the
memchecker.
Change-Id: Id1a6b8f02853789b108ef6003f4c32ab929bb123
Reviewed-by: Andreas Hansson <andreas.hansson@arm.com>
Reviewed-by: Stephan Diestelhorst <stephan.diestelhorst@arm.com>
|
|
First of five patches adding RISC-V to GEM5. This patch introduces the
base 64-bit ISA (RV64I) in src/arch/riscv for use with syscall emulation.
The multiply, floating point, and atomic memory instructions will be added
in additional patches, as well as support for more detailed CPU models.
The loader is also modified to be able to parse RISC-V ELF files, and a
"Hello world\!" example for RISC-V is added to test-progs.
Patch 2 will implement the multiply extension, RV64M; patch 3 will implement
the floating point (single- and double-precision) extensions, RV64FD;
patch 4 will implement the atomic memory instructions, RV64A, and patch 5
will add support for timing, minor, and detailed CPU models that is missing
from the first four patches (such as handling locked memory).
[Removed several unused parameters and imports from RiscvInterrupts.py,
RiscvISA.py, and RiscvSystem.py.]
[Fixed copyright information in RISC-V files copied from elsewhere that had
ARM licenses attached.]
[Reorganized instruction definitions in decoder.isa so that they are sorted
by opcode in preparation for the addition of ISA extensions M, A, F, D.]
[Fixed formatting of several files, removed some variables and
instructions that were missed when moving them to other patches, fixed
RISC-V Foundation copyright attribution, and fixed history of files
copied from other architectures using hg copy.]
[Fixed indentation of switch cases in isa.cc.]
[Reorganized syscall descriptions in linux/process.cc to remove large
number of repeated unimplemented system calls and added implmementations
to functions that have received them since it process.cc was first
created.]
[Fixed spacing for some copyright attributions.]
[Replaced the rest of the file copies using hg copy.]
[Fixed style check errors and corrected unaligned memory accesses.]
[Fix some minor formatting mistakes.]
Signed-off by: Alec Roelke
Signed-off by: Jason Lowe-Power <jason@lowepower.com>
|
|
This function was used by the now-defunct InOrderCPU model. Since this
model is no longer in gem5, this function was not called from anywhere in
the code.
|
|
Modify the opClass assigned to AArch64 FP instructions from SimdFloat* to
Float*. Also create the FloatMemRead and FloatMemWrite opClasses, which
distinguishes writes to the INT and FP register banks.
Change the latency of (Simd)FloatMultAcc to 5, based on the Cortex-A72,
where the "latency" of FMADD is 3 if the next instruction is a FMADD and
has only the augend to destination dependency, otherwise it's 7 cycles.
Signed-off-by: Jason Lowe-Power <jason@lowepower.com>
|
|
networktest is essentially a collection of synthetic traffic patterns
for the network. The protocol name and the tester having the same name
led to multiple python configuration files with the same name, adding
confusion. This patch renames networktest to garnet_synthetic_traffic,
and also adds more synthetic traffic patterns.
|
|
The drain did not wait until stages were ready again. Therefore, as a
result of messages in the TimeBuffer being drain, the state after the
drain was not consistent and asserts fired in some places when the
draining happened after a stage got blocked, but before the notification
arrived to the previous stages.
Change-Id: Ib50b3b40b7f745b62c1eba2931dec76860824c71
Reviewed-by: Andreas Sandberg <andreas.sandberg@arm.com>
|
|
This change adds a Trace CPU param to exit simulation early,
i.e. when the first (any one) trace execution is complete. With
this change the user gets a choice to configure exit as either
when the last CPU finishes (default) or first CPU finishes
replay. Configuring an early exit enables simulating and
measuring stats strictly when memory-system resources are being
stressed by all Trace CPUs.
Change-Id: I3998045fdcc5cd343e1ca92d18dd7f7ecdba8f1d
Reviewed-by: Nikos Nikoleris <nikos.nikoleris@arm.com>
|
|
This change subtracts the time offset present in the trace from
all the event times when nodes and request are sent so that the
replay starts immediately when the simulation starts. This makes
the stats accurate when the time offset in traces is large, for
example when traces are generated in the middle of a workload
execution. It also solves the problem of unnecessary DRAM
refresh events that would keep occuring during the large time
offset before even a single request is replayed into the system.
Change-Id: Ie0898842615def867ffd5c219948386d952af7f7
Reviewed-by: Nikos Nikoleris <nikos.nikoleris@arm.com>
|
|
This change adds a simple feature to scale the frequency of
the Trace CPU.
The compute delays in the input traces provide timing. This
change adds a freqency multiplier parameter to the Trace CPU
set to 1.0 by default. The compute delay is manipulated to
effectively achieve the frequency at which the nodes become
ready and thus scale the frequency of the Trace CPU.
Change-Id: Iaabbd57806941ad56094fcddbeb38fcee1172431
Reviewed-by: Nikos Nikoleris <nikos.nikoleris@arm.com>
|
|
This patch enables timing accesses for KVM cpu. A new state,
RunningMMIOPending, is added to indicate that there are outstanding timing
requests generated by KVM in the system. KVM's tick() is disabled and the
simulation does not enter into KVM until all outstanding timing requests have
completed. The main motivation for this is to allow KVM CPU to perform MMIO
in Ruby, since Ruby does not support atomic accesses.
|
|
The quiesce family of magic ops can be simplified by the inclusion of
quiesceTick() and quiesce() functions on ThreadContext. This patch also
gets rid of the FS guards, since suspending a CPU is also a valid
operation for SE mode.
|
|
Only map memories into the KVM guest address space that are
marked as usable by KVM. Create BackingStoreEntry class
containing flags for is_conf_reported, in_addr_map, and
kvm_map.
|
|
Signed-off-by: Andreas Sandberg <andreas.sandberg@arm.com>
|
|
Change-Id: Ic37311443ca11ee6d95bceffea599e054e7aa110
Reviewed-by: Andreas Sandberg <andreas.sandberg@arm.com>
|
|
Change-Id: I183b9942929c873c3272ce6d1abd4ebc472c7132
Reviewed-by: Andreas Sandberg <andreas.sandberg@arm.com>
|
|
The behavior of WFI is to cause minor to cease evaluating
pipeline logic until an interrupt is observed, however
a user may wish to drain the system while a core is sleeping
due to a WFI. This patch makes WFI drain. If an actual
drain occurs during a WFI, the CPU is already drained and will
immediately be ready for swapping, checkpointing, etc. This
should not negatively impact performance as WFI instructions
are 'stream-changing' (treated like unpredicted branches), so
all remaining instructions are wrong-path and will be squashed
rapidly.
Change-Id: I63833d5acb53d8dde78f9f0c9611de0ece385e45
|
|
This patch adds SMT support to the MinorCPU. Currently
RoundRobin or Random thread scheduling are supported.
Change-Id: I91faf39ff881af5918cca05051829fc6261f20e3
|
|
The traffic generator currently resolves relative trace paths relative
to gem5's current working directory. This can lead to surprising
results for relative paths where the expectation would normally be
that they are resolved relative to the configuration file. This
changeset implements config-relative trace file lookups. The old
behavior is kept as a fallback for configs that expect that behavior.
Change-Id: I1bda4e16725842666ffc37dcb6838c23a6ff138c
Signed-off-by: Andreas Sandberg <andreas.sandberg@arm.com>
Reviewed-by: Curtis Dunham <curtis.dunham@arm.com>
|
|
Add functionality to the BaseCPU that will put the entire CPU
into a low-power idle state whenever all threads in it are idle.
Change-Id: I984d1656eb0a4863c87ceacd773d2d10de5cfd2b
|
|
Fixing an issue with regStats not calling the parent class method
for most SimObjects in Gem5. This causes issues if one adds new
stats in the base class (since they are never initialized properly!).
Change-Id: Iebc5aa66f58816ef4295dc8e48a357558d76a77c
Reviewed-by: Andreas Sandberg <andreas.sandberg@arm.com>
|
|
We want to extend the stats of objects hierarchically and thus it is necessary
to register the statistics of the base-class(es), as well. For now, these are
empty, but generic stats will be added there.
Patch originally provided by Akash Bagdia at ARM Ltd.
|
|
MinorCPU fix for corrupt numCycles when resuming from a previous simulation.
---
src/cpu/minor/cpu.cc | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
|
|
This patch adds a progress check to the TrafficGen so that it is
easier to detect deadlock scenarios where the generator gets stuck
waiting for a retry, and makes no further progress.
Change-Id: Ifb8779ad0939f52c0518d0e867bac73f99b82e2b
Reviewed-by: Andreas Sandberg <andreas.sandberg@arm.com>
Reviewed-by: Radhika Jagtap <radhika.jagtap@arm.com>
|
|
In general, the ThreadID parameter is unnecessary in the memory system
as the ContextID is what is used for the purposes of locks/wakeups.
Since we allocate sequential ContextIDs for each thread on MT-enabled
CPUs, ThreadID is unnecessary as the CPUs can identify the requesting
thread through sideband info (SenderState / LSQ entries) or ContextID
offset from the base ContextID for a cpu.
This is a re-spin of 20264eb after the revert (bd1c6789) and includes
some fixes of that commit.
|
|
Branch predictors that use GHRs should index them on a
per-thread basis. This makes that so.
This is a re-spin of fb51231 after the revert (bd1c6789).
|
|
This patch adds a configurable indirect branch predictor that can be indexed
by a combination of GHR and path history hashes. Implements the functionality
described in:
"Target prediction for indirect jumps" by Chang, Hao, and Patt
http://dl.acm.org/citation.cfm?id=264209
This is a re-spin of fb9d142 after the revert (bd1c6789).
|
|
The extant BTB code doesn't hash on the thread id but does check the
thread id for 'btb hits'. This results in 1-thread of a multi-threaded
workload taking a BTB entry, and all other threads missing for the same branch
missing.
|
|
|
|
The following patches had unexpected interactions with the current
upstream code and have been reverted for now:
e07fd01651f3: power: Add support for power models
831c7f2f9e39: power: Low-power idle power state for idle CPUs
4f749e00b667: power: Add power states to ClockedObject
Signed-off-by: Andreas Sandberg <andreas.sandberg@arm.com>
--HG--
extra : amend_source : 0b6fb073c6bbc24be533ec431eb51fbf1b269508
|
|
In general, the ThreadID parameter is unnecessary in the memory system
as the ContextID is what is used for the purposes of locks/wakeups.
Since we allocate sequential ContextIDs for each thread on MT-enabled
CPUs, ThreadID is unnecessary as the CPUs can identify the requesting
thread through sideband info (SenderState / LSQ entries) or ContextID
offset from the base ContextID for a cpu.
|
|
Branch predictors that use GHRs should index them on a
per-thread basis. This makes that so.
|
|
This patch adds a configurable indirect branch predictor that can be indexed
by a combination of GHR and path history hashes. Implements the functionality
described in:
"Target prediction for indirect jumps" by Chang, Hao, and Patt
http://dl.acm.org/citation.cfm?id=264209
|
|
The extant BTB code doesn't hash on the thread id but does check the
thread id for 'btb hits'. This results in 1-thread of a multi-threaded
workload taking a BTB entry, and all other threads missing for the same branch
missing.
|
|
Add functionality to the BaseCPU that will put the entire CPU into a low-power
idle state whenever all threads in it are idle.
|
|
Add 4 power states to the ClockedObject, provides necessary access functions
to check and update the power state. Default power state is UNDEFINED, it is
responsibility of the respective simulation model to provide the startup state
and any other logic for state change.
Add number of transition stat.
Add distribution of time spent in clock gated state.
Add power state residency stat.
Add dump call back function to allow stats update of distribution and residency
stats.
|
|
|
|
This patch adds the ability for the simulator to query the number of
instructions a CPU has executed so far per hw-thread. This can be used
to enable more flexible periodic events such as taking checkpoints
starting 1s into simulation and X instructions thereafter.
|
