| Age | Commit message (Collapse) | Author |
|---|
|
|
|
|
|
The functionality of updating and returning the delay cycles would now be
performed by the dequeue() function itself.
|
|
This patch makes a more firm connection between the DDR3-1600
configuration and the corresponding datasheet, and also adds a
DDR3-2133 and a DDR4-2400 configuration. At the moment there is also
an ongoing effort to align the choice of datasheets to what is
available in DRAMPower.
|
|
This patch extends the current timing parameters with the DRAM cycle
time. This is needed as the DRAMPower tool expects timestamps in DRAM
cycles. At the moment we could get away with doing this in a
post-processing step as the DRAMPower execution is separate from the
simulation run. However, in the long run we want the tool to be called
during the simulation, and then the cycle time is needed.
|
|
This patch simplifies the DRAM response scheduling based on the
assumption that they are always returned in order.
|
|
This patch adds the basic ingredients for a precharge all operation,
to be used in conjunction with DRAM power modelling.
Currently we do not try and apply any cleverness when precharging all
banks, thus even if only a single bank is open we use PREA as opposed
to PRE. At the moment we only have a single tRP (tRPpb), and do not
model the slightly longer all-bank precharge constraint (tRPab).
|
|
This patch removes the redundant printing of DRAM params.
|
|
This patch adds the tRTP timing constraint, governing the minimum time
between a read command and a precharge. Default values are provided
for the existing DRAM types.
|
|
This patch merges the two control paths used to estimate the latency
and update the bank state. As a result of this merging the computation
is now in one place only, and should be easier to follow as it is all
done in absolute (rather than relative) time.
As part of this change, the scheduling is also refined to ensure that
we look at a sensible estimate of the bank ready time in choosing the
next request. The bank latency stat is removed as it ends up being
misleading when the DRAM access code gets evaluated ahead of time (due
to the eagerness of waking the model up for scheduling the next
request).
|
|
This patch adds the write recovery time to the DRAM timing
constraints, and changes the current tRASDoneAt to a more generic
preAllowedAt, capturing when a precharge is allowed to take place.
The part of the DRAM access code that accounts for the precharge and
activate constraints is updated accordingly.
|
|
This patch treats the closed page policy as yet another case of
auto-precharging, and thus merges the code with that used for the
other policies.
|
|
This patch adds power states to the controller. These states and the
transitions can be used together with the Micron power model. As a
more elaborate use-case, the transitions can be used to drive the
DRAMPower tool.
At the moment, the power-down modes are not used, and this patch
simply serves to capture the idle, auto refresh and active modes. The
patch adds a third state machine that interacts with the refresh state
machine.
|
|
This patch adds a state machine for the refresh scheduling to
ensure that no accesses are allowed while the refresh is in progress,
and that all banks are propely precharged.
As part of this change, the precharging of banks of broken out into a
method of its own, making is similar to how activations are dealt
with. The idle accounting is also updated to ensure that the refresh
duration is not added to the time that the DRAM is in the idle state
with all banks precharged.
|
|
This patch changes the read/write event loop to use a single event
(nextReqEvent), along with a state variable, thus joining the two
control flows. This change makes it easier to follow the state
transitions, and control what happens when.
With the new loop we modify the overly conservative switching times
such that the write-to-read switch allows bank preparation to happen
in parallel with the bus turn around. Similarly, the read-to-write
switch uses the introduced tRTW constraint.
|
|
This patch squashes prefetch requests from downstream caches,
so that they do not steal cachelines away from caches closer
to the cpu. It was originally coded by Mitch Hayenga and
modified by Aasheesh Kolli.
|
|
Splits the CommMonitor trace_file parameter into three parameters. Previously,
the trace was only enabled if the trace_file parameter was set, and would be
written to this file. This patch adds in a trace_enable and trace_compress
parameter to the CommMonitor.
No trace is generated if trace_enable is set to False. If it is set to True, the
trace is written to a file based on the name of the SimObject in the simulation
hierarchy. For example, system.cluster.il1_commmonitor.trc. This filename can be
overridden by additionally specifying a file name to the trace_file parameter
(more on this later).
The trace_compress parameter will append .gz to any filename if set to True.
This enables compression of the generated traces. If the file name already ends
in .gz, then no changes are made.
The trace_file parameter will override the name set by the trace_enable
parameter. In the case that the specified name does not end in .gz but
trace_compress is set to true, .gz is appended to the supplied file name.
|
|
This never actually worked since it was printing out only a word
of the cache block and not the entire thing and doubly didn't work
csprintf overrides the %#x specifier and assumes a char* array is
actually a string.
|
|
Has not been maintained at all. Since there is alternate documentation
available on gem5.org, no need to have this separately.
|
|
It had an unnecessary pairs token which is being removed.
|
|
Upon aggregating records, serialize system's cache-block size, as the
cache-block size can be different when restoring from a checkpoint. This way,
we can correctly read all records when restoring from a checkpoints, even if
the cache-block size is different.
Note, that it is only possible to restore from a checkpoint if the
desired cache-block size is smaller or equal to the cache-block size
when the checkpoint was taken; we can split one larger request into
multiple small ones, but it is not reliable to do the opposite.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
As of now, the enqueue statement can take in any number of 'pairs' as
argument. But we only use the pair in which latency is the key. This
latency is allowed to be either a fixed integer or a member variable of
controller in which the expression appears. This patch drops the use of pairs
in an enqueue statement. Instead, an expression is allowed which will be
interpreted to be the latency of the enqueue. This expression can anything
allowed by slicc including a constant integer or a member variable.
|
|
The phrase is no longer valid since we do not distinguish between
inter and intra chip communication.
|
|
This patch adds stats for tracking the number of reads/writes per bus
turn around, and also adds hysteresis to the write-to-read switching
to ensure that the queue does not oscilate around the low threshold.
|
|
This patch renames the not-so-simple SimpleDRAM to a more suitable
DRAMCtrl. The name change is intended to ensure that we do not send
the wrong message (although the "simple" in SimpleDRAM was originally
intended as in cleverly simple, or elegant).
As the DRAM controller modelling work is being presented at ISPASS'14
our hope is that a broader audience will use the model in the future.
--HG--
rename : src/mem/SimpleDRAM.py => src/mem/DRAMCtrl.py
rename : src/mem/simple_dram.cc => src/mem/dram_ctrl.cc
rename : src/mem/simple_dram.hh => src/mem/dram_ctrl.hh
|
|
Make the default memory type DDR3-1600 x64, and use the open-adaptive
page policy. This change is aiming to ensure that users by default are
using a realistic memory system.
|
|
This patch adds a second adaptive page policy to the DRAM controller,
closing the page unless there are already queued accesses to the open
page.
|
|
Minor tidying up and removing of redundant code, including the
printing of queue state every million accesses.
|
|
This patch ensures that we do not sample the bytes per activate when
the row has already been closed.
|
|
This patch adds a basic starvation-prevention mechanism where a DRAM
page is forced to close after a certain number of accesses. The limit
is combined with the open and open-adaptive page policy and if reached
causes an auto-precharge.
|
|
This patch changes the triggering condition for the write draining
such that we grab the opportunity to issue writes if there are no
reads waiting (as opposed to waiting for the writes to reach the high
threshold). As a result, we potentially drain some of the writes in read
idle periods (if any).
A low threshold is added to be able to control how many write bursts
are kept in the memory controller queue (acting as on-chip storage).
The high and low thresholds are updated to sensible values for a 32/64
size write buffer. Note that the thresholds should be adjusted along
with the queue sizes.
This patch also adds some basic initialisation sanity checks and moves
part of the initialisation to the constructor.
|
|
This patch adds a new DDR3 configuration to match with the parameters
that are specified in one of the DDR3 configs used in DRAMSim2.
|
|
This patch adds the row bits to the name of the address mapping
schemes to make it more clear that all the current schemes places the
row bits as the most significant bits.
|
|
This patch moves the Ruby-related debug flags to the ruby
sub-directory, and also removes the state SConsopts that add the
no-longer-used NO_VECTOR_BOUNDS_CHECK.
|
|
This patch makes sure DRAMSim2 is included in a build of the NULL ISA.
|
|
Add a warning to the CommMonitor which will alert the user if they try
and record a trace when the system is not in timing mode.
|
|
Each consumer object maintains a set of tick values when the object is supposed
to wakeup and do some processing. As of now, the object accesses this set both
when scheduling a wakeup event and when the object actually wakes up. The set
is accessed during wakeup to remove the current tick value from the set. This
functionality is now being moved to the scheduling function where ticks are
removed at a later time.
|
|
This helps in configuring the network interfaces from the python script and
these objects no longer rely on the network object for the timing information.
|
|
|
|
Piobus was recently added to se scripts for ruby so that the interrupt
controller can be connected to something (required since the interrupt
controller sends address range messages). This patch removes the piobus
and instead, the pio port of ruby port will now ignore the range change
messages in se mode.
|
|
|
|
This patch fixes an assert condition that is not true at all
times. There are valid situations that arise in dual-core
dual-workload runs where the assert condition is false. The function
call following the assert however needs to be called only when the
condition is true (a block cannot be invalidated in the tags structure
if has not been allocated in the structure, and the tempBlock is never
allocated). Hence the 'assert' has been replaced with an 'if'.
|
|
For systems without caches, the LLSC code does not get snoops for
wake-ups. We add the LLSC code in the abstract memory to do the job
for us.
|
|
The last pop operation is now tracked as a Tick instead of in Cycles.
This helps in avoiding use of the receiver's clock during the enqueue
operation.
|
|
|
|
Couple of users observed segmentation fault when the simulator tries to
register the statistical variable m_IncompleteTimes. It seems that there
is some problem with the initialization of these variables when allocated
in the constructor.
|
|
Currently, the interrupt controller in x86 is connected to the io bus
directly. Therefore the packets between the io devices and the interrupt
controller do not go through ruby. This patch changes ruby port so that
these packets arrive at the ruby port first, which then routes them to their
destination. Note that the patch does not make these packets go through the
ruby network. That would happen in a subsequent patch.
|
|
This patch simplfies the retry logic in the RubyPort, avoiding
redundant attributes, and enforcing more stringent checks on the
interactions with the normal ports. The patch also simplifies the
routing done by the RubyPort, using the port identifiers instead of a
heavy-weight sender state.
The patch also fixes a bug in the sending of responses from PIO
ports. Previously these responses bypassed the queue in the queued
port, and ignored the return value, potentially leading to response
packets being lost.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
Code in two of the functions was exactly the same. This patch moves
this code to a new function which is called from the two functions
mentioned initially.
|
|
|
