| Age | Commit message (Collapse) | Author |
|---|
|
If a split load fails on a blocked cache wbOutstanding can be decremented
twice if the first part of the split load succeeds and the second part fails.
Condition the decrementing on not having completed the first part of the load.
|
|
This patch fixes two problems with the O3 cpu model. The first is an issue
with an instruction fetch causing a fault on the next address while the
current macro-op is being issued. This happens when the micro-ops exceed
the fetch bandwdith and then on the next cycle the fetch stage attempts
to issue a request to the next line while it still has micro-ops to issue
if the next line faults a fault is attached to a micro-op in the currently
executing macro-op rather than a "nop" from the next instruction block.
This leads to an instruction incorrectly faulting when on fetch when
it had no reason to fault.
A similar problem occurs with interrupts. When an interrupt occurs the
fetch stage nominally stops issuing instructions immediately. This is incorrect
in the case of a macro-op as the current location might not be interruptable.
|
|
The virtual channels within "response" vnets are made buffers_per_data_vc
deep (default=4), while virtual channels within other vnets are made
buffers_per_ctrl_vc deep (default = 1). This is for accurate power estimates.
|
|
Forgot to add this to MI_example in my previous patch.
|
|
|
|
Identifying response vnets versus other vnets will allow garnet to
determine which vnets will carry data packets, and which will carry
ctrl packets, and use appropriate buffer sizes (since data packets are larger
than ctrl packets). This in turn allows the orion power model to accurately
estimate buffer power.
|
|
Renamed (message) class to vnet for consistency with rest of ruby.
Moved some parameters specific to fixed/flexible garnet networks into their
corresponding py files.
|
|
This change further eliminates cases where condition codes were being read
just so they could be written without change because the instruction in
question was supposed to preserve them. This is done by creating the condition
code code based on the input rather than just doing a simple substitution.
|
|
If one of the condition codes isn't being used in the execution we should only
read it if the instruction might be dependent on it. With the preeceding changes
there are several more cases where we should dynamically pick instead of assuming
as we did before.
|
|
Break up the condition code bits into NZ, C, V registers. These are individually
written and this removes some incorrect dependencies between instructions.
|
|
Move the saturating bit (which is also saturating) from the renamed register
that holds the flags to the CPSR miscreg and adds a allows setting it in a
similar way to the FP saturating registers. This removes a dependency in
instructions that don't write, but need to preserve the Q bit.
|
|
This change splits out the condcodes from being one monolithic register
into three blocks that are updated independently. This allows CPUs
to not have to do RMW operations on the flags registers for instructions
that don't write all flags.
|
|
Debug flags are ExecUser, ExecKernel, and ExecAsid. ExecUser and
ExecKernel are set by default when Exec is specified. Use minus
sign with ExecUser or ExecKernel to remove user or kernel tracing
respectively.
|
|
Add registers and components to better support the VersatileEB board.
Made the MIDR and SYS_ID register parameters to ArmSystem and RealviewCtrl
respectively.
|
|
Instructions that load an address and are control instructions can
execute down the wrong path if they were predicted correctly and then
instructions following them are squashed. If an instruction is a
memory and control op use the predicted address for the next PC instead
of just advancing the PC. Without this change NPC is used for the next
instruction, but predPC is used to verify that the branch was successful
so the wrong path is silently executed.
|
|
we can add it back within python in some future changeset
|
|
|
|
Build a python list and dict of all stats and expose flags properly.
--HG--
rename : src/python/m5/stats.py => src/python/m5/stats/__init__.py
|
|
|
|
The network tester terminates after injecting for sim_cycles
(default=1000), instead of having to explicitly pass --maxticks from the
command line as before. If fixed_pkts is enabled, the tester only
injects maxpackets number of packets, else it keeps injecting till sim_cycles.
The tester also works with zero command line arguments now.
|
|
|
|
The options trace-help and trace-flags are no longer required. In there place,
the options debug-help and debug-flags have been provided.
|
|
|
|
The RubyMemory flag wasnt used in the code, creating large gaps in trace output. Replace cprintfs w/dprintfs
using RubyMemory in memory controller. DPRINTF also deprecate the usage of the setDebug() pure virtual
function in the AbstractMemoryOrCache Class as well the m_debug/cprintf functions in MemoryControl.hh/cc
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
If we fault, change the state to faulting so that we don't fault again in the same cycle.
|
|
If an nonspeculative instruction has a fault it might not be in the
nonSpecInsts map.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Therefore all links by default are 16 bytes wide and thus work with Garnet's
uniform link bandwidth assumption.
|
|
|
|
The simple network's endpoint bandwidth value is used to adjust the overall
bandwidth of the network. Specifically, the ration between endpoint bandwidth
and the MESSAGE_SIZE_MULTIPLIER determines the increase. By setting the value
to 1000, that means the bandwdith factor specified in the links translates to
the link bandwidth in bytes. Previously, it was increasing that value by 10.
This patch will likely require a reset of the ruby regression tester stats.
|
|
|
|
Moved the buffer_size, endpoint_bandwidth, and adaptive_routing params out of
the top-level parent network object and to only those networks that actually
use those parameters.
|
|
This patch ensures that both Garnet and the simple networks use the bw value
specified in the topology. To do so, the patch generalizes the specification
of bw for basic links. This value is then translated to the specific value
used by the simple and Garnet networks. Since Garent does not support
non-uniformed link bandwidth, the patch also adds a check to ensure all bws are
equal.
--HG--
rename : src/mem/ruby/network/BasicLink.cc => src/mem/ruby/network/simple/SimpleLink.cc
rename : src/mem/ruby/network/BasicLink.hh => src/mem/ruby/network/simple/SimpleLink.hh
rename : src/mem/ruby/network/BasicLink.py => src/mem/ruby/network/simple/SimpleLink.py
|
|
This patch converts links and switches from second class simobjects that were
virtually ignored by the networks (both simple and Garnet) to first class
simobjects that directly correspond to c++ ojbects manipulated by the
topology and network classes. This is especially true for Garnet, where the
links and switches directly correspond to specific C++ objects.
By making this change, many aspects of the Topology class were simplified.
--HG--
rename : src/mem/ruby/network/Network.cc => src/mem/ruby/network/BasicLink.cc
rename : src/mem/ruby/network/Network.hh => src/mem/ruby/network/BasicLink.hh
rename : src/mem/ruby/network/Network.cc => src/mem/ruby/network/garnet/fixed-pipeline/GarnetLink_d.cc
rename : src/mem/ruby/network/Network.hh => src/mem/ruby/network/garnet/fixed-pipeline/GarnetLink_d.hh
rename : src/mem/ruby/network/garnet/fixed-pipeline/GarnetNetwork_d.py => src/mem/ruby/network/garnet/fixed-pipeline/GarnetLink_d.py
rename : src/mem/ruby/network/garnet/fixed-pipeline/GarnetNetwork_d.py => src/mem/ruby/network/garnet/fixed-pipeline/GarnetRouter_d.py
rename : src/mem/ruby/network/Network.cc => src/mem/ruby/network/garnet/flexible-pipeline/GarnetLink.cc
rename : src/mem/ruby/network/Network.hh => src/mem/ruby/network/garnet/flexible-pipeline/GarnetLink.hh
rename : src/mem/ruby/network/garnet/fixed-pipeline/GarnetNetwork_d.py => src/mem/ruby/network/garnet/flexible-pipeline/GarnetLink.py
rename : src/mem/ruby/network/garnet/fixed-pipeline/GarnetNetwork_d.py => src/mem/ruby/network/garnet/flexible-pipeline/GarnetRouter.py
|
|
|
|
Moved the Topology class to the top network directory because it is shared by
both the simple and Garnet networks.
--HG--
rename : src/mem/ruby/network/simple/Topology.cc => src/mem/ruby/network/Topology.cc
rename : src/mem/ruby/network/simple/Topology.hh => src/mem/ruby/network/Topology.hh
|
