| Age | Commit message (Collapse) | Author |
|---|
|
This patch introduces a mirrored internal snoop port to facilitate
easy addition of flow control for the snoop responses that are turned
into normal responses on their return. To perform this, the slave
ports of the coherent bus are wrapped in internal master ports that
are passed as the source ports to the response layer in question.
As a result of this patch, there is more contention for the response
resources, and as such system performance will decrease slightly.
A consequence of the mirrored internal port is that the port the bus
tells to retry (the internal one) and the port actually retrying (the
mirrored) one are not the same. Thus, the existing check in tryTiming
is not longer correct. In fact, the test is redundant as the layer is
only in the retry state while calling sendRetry on the waiting port,
and if the latter does not immediately call the bus then the retry
state is left. Consequently the check is removed.
|
|
This patch makes the buses multi layered, and effectively creates a
crossbar structure with distributed contention ports at the
destination ports. Before this patch, a bus could have a single
request, response and snoop response in flight at any time, and with
these changes there can be as many requests as connected slaves (bus
master ports), and as many responses as connected masters (bus slave
ports).
Together with address interleaving, this patch enables us to create
high-throughput memory interconnects, e.g. 50+ GByte/s.
|
|
This patch makes the flow control and state updates of the coherent
bus more clear by separating the two cases, i.e. forward as a snoop
response, or turn it into a normal response.
With this change it is also more clear what resources are being
occupied, and that we effectively bypass the busy check for the second
case. As a result of the change in resource usage some stats change.
|
|
This patch does some minor housekeeping on the bus code, removing
redundant code, and moving the extraction of the destination id to the
top of the functions using it.
|
|
This patch adds a basic set of stats which are hard to impossible to
implement using only communication monitors, and are needed for
insight such as bus utilization, transactions through the bus etc.
Stats added include throughput and transaction distribution, and also
a two-dimensional vector capturing how many packets and how much data
is exchanged between the masters and slaves connected to the bus.
|
|
This patch changes the set used to track outstanding requests to an
unordered set (part of C++11 STL). There is no need to maintain the
order, and hopefully there might even be a small performance benefit.
|
|
This patch fixes a bug in the bus where the bus transitions from busy
to idle and still has a port that is waiting for a retry from a peer.
|
|
This patch adds a typical (leaning towards fast) LPDDR3 configuration
based on publically available data. As expected, it looks very similar
to the LPDDR2-S4 configuration, only with a slightly lower burst time.
|
|
This patch adapts the existing LPDDR2 configuration to make use of the
multi-channel functionality. Thus, to get a x64 interface two
controllers should be instantiated using the makeMultiChannel method.
The page size and ranks are also adapted to better suit with a typical
LPDDR2 part.
|
|
This patch removes the explicit memset as it is redundant and causes
the simulator to touch the entire space, forcing the host system to
allocate the pages.
Anonymous pages are mapped on the first access, and the page-fault
handler is responsible for zeroing them. Thus, the pages are still
zeroed, but we avoid touching the entire allocated space which enables
us to use much larger memory sizes as long as not all the memory is
actually used.
|
|
This patch changes how the streams are created to avoid the size
limitation on the coded streams. As we only read/write a single
message at a time, there is never any message larger than a few
bytes. However, the coded stream eventually complains that its
internal counter reaches 64+ MByte if the total file size exceeds this
value.
Based on suggestions in the protobuf discussion forums, the coded
stream is now created for every message that is read/written. The
result is that the internal byte count never goes about tens of bytes,
and we can read/write any size file that the underlying file I/O can
handle.
|
|
This patch changes the type of the hash function for BasicBlockRanges
to match the original definition of the templatized type. Without
this, clang raises a warning and combined with the "-Werror" flag this
causes compilation to fail.
|
|
|
|
This is the x86 version of the ARM changeset baa17ba80e06. In case an
instruction has been squashed by the o3 cpu, this patch allows page
table walker to avoid carrying out a pending translation that the
instruction requested for.
|
|
Currently call and return instructions are marked as IsCall and IsReturn. Thus, the
branch predictor does not use RAS for these instructions. Similarly, the number of
function calls that took place is recorded as 0. This patch marks these instructions
as they should be.
|
|
Currently all the integer microops are marked as IntAluOp and the floating
point microops are marked as FloatAddOp. This patch adds support for marking
different microops differently. Now IntMultOp, IntDivOp, FloatDivOp,
FloatMultOp, FloatCvtOp, FloatSqrtOp classes will be used as well. This will
help in providing different latencies for different op class.
|
|
Updates copyright years, removes space at the end of lines, shortens
variable names.
|
|
Updates copyright years, removes space at the end of lines, shortens
variable names.
|
|
Updates copyright years, removes space at the end of lines, shortens
variable names.
|
|
Updates copyright years, removes space at the end of lines, shortens
variable names.
|
|
This patch changes the way cache statistics are collected in ruby.
As of now, there is separate entity called CacheProfiler which holds
statistical variables for caches. The CacheMemory class defines different
functions for accessing the CacheProfiler. These functions are then invoked
in the .sm files. I find this approach opaque and prone to error. Secondly,
we probably should not be paying the cost of a function call for recording
statistics.
Instead, this patch allows for accessing statistical variables in the
.sm files. The collection would become transparent. Secondly, it would happen
in place, so no function calls. The patch also removes the CacheProfiler class.
--HG--
rename : src/mem/slicc/ast/InfixOperatorExprAST.py => src/mem/slicc/ast/OperatorExprAST.py
|
|
having separate params for the local/globalHistoryBits and the
local/globalPredictorSize can lead to inconsistencies if they
are not carefully set. this patch dervies the number of bits
necessary to index into the local/global predictors based on
their size.
the value of the localHistoryTableSize for the ARM O3 CPU has been
increased to 1024 from 64, which is more accurate for an A15 based
on some correlation against A15 hardware.
|
|
Add the option useCoalescedMMIO to the BaseKvmCPU. The default
behavior is to disable coalesced MMIO since this hasn't been heavily
tested.
|
|
|
|
The CpuPort class was removed before the KVM patches were committed,
which means that the KVM interface currently doesn't compile. This
changeset adds the BaseKvmCPU::KVMCpuPort class which derives from
MasterPort. This class is used on the data and instruction ports
instead of the old CpuPort.
|
|
|
|
This changeset adds a 'numInsts' stat to the KVM-based CPU. It also
cleans up the variable names in kvmRun to make the distinction between
host cycles and estimated simulated cycles clearer. As a bonus
feature, it also fixes a warning (unreferenced variable) when
compiling in fast mode.
|
|
Add a debug print (when the Checkpoint debug flag is set) on serialize
and unserialize. Additionally, dump the KVM state before
serializing. The KVM state isn't dumped after unserializing since the
state is loaded lazily on the next KVM entry.
|
|
Device accesses are normally uncacheable. This change probably doesn't
make any difference since we normally disable caching when KVM is
active. However, there might be devices that check this, so we'd
better enable this flag to be safe.
|
|
|
|
The vsyscall address for gettimeofday is 0xffffffffff600000ul. The offset
therefore should be 0x0 instead of 0x410. This can be cross checked with
the file sysdeps/unix/sysv/linux/x86_64/gettimeofday.c in source of glibc.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
The existing implementation can read uninitialized data or stale information
from the cached PageTable entries.
1) Add a valid bit for the cache entries. Simply using zero for the virtual
address to signify invalid entries is not sufficient. Speculative, wrong-path
accesses frequently access page zero. The current implementation would return
a uninitialized TLB entry when address zero was accessed and the PageTable
cache entry was invalid.
2) When unmapping/mapping/remaping a page, invalidate the corresponding
PageTable cache entry if one already exists.
|
|
This patch ensures the flags are always initialised.
|
|
|
|
The 'lret' instruction reloads instruction pointer and code segment from the
stack and then pops them. But the popping part is missing from the current
implementation. This caused incorrect behavior in some code related to the
Fiasco OS. Microops are being added to rectify the behavior of the instruction.
Committed by: Nilay Vaish <nilay@cs.wisc.edu>
|
|
Due to recent changes to clocking system in Ruby and the way Ruby restores
state from a checkpoint, garnet was failing to run from a checkpointed state.
The problem is that Ruby resets the time to zero while warming up the caches.
If any component records a local copy of the time (read calls curCycle())
before the simulation has started, then that component will not operate until
that time is reached. In the context of this particular patch, the Garnet
Network class calls curCycle() at multiple places. Any non-operational
component can block in requests in the memory system, which the system
interprets as a deadlock. This patch makes changes so that Garnet can
successfully run from checkpointed state.
It adds a globally visible time at which the actual execution started. This
time is initialized in RubySystem::startup() function. This variable is only
meant for components with in Ruby. This replaces the private variable that
was maintained within Garnet since it is not possible to figure out the
correct time when the value of this variable can be set.
The patch also does away with all cases where curCycle() is called with in
some Ruby component before the system has actually started executing. This
is required due to the quirky manner in which ruby restores from a checkpoint.
|
|
This patch adds an address mapping scheme where the channel
interleaving takes place on a cache line granularity. It is similar to
the existing RaBaChCo that interleaves on a DRAM page, but should give
higher performance when there is less locality in the address
stream.
|
|
This patch changes the slightly ambigious names used for the address
mapping scheme to be more descriptive, and actually spell out what
they do. With this patch we also open up for adding more flavours of
open- and close-type mappings, i.e. interleaving across channels with
the open map.
|
|
This patch changes the TraceGen such that it uses the optional request
flags from the protobuf trace if they are present.
|
|
This patch enables the use of the generator behaviours outside the
TrafficGen module. This is useful e.g. to allow packet replay modes
for other devices in the system without having to replace them with a
TrafficGen in the configuration files.
This change also enables more specific behaviours to be composed as
specific modules, e.g. BaseBandModem can use a number of generators
and have application-specific parameters based around a specific set
of generators.
|
|
This patch adds a WideIO 200 MHz configuration that can be used as a
baseline to compare with DDRx and LPDDRx. Note that it is a single
channel and that it should be replicated 4 times. It is based on
publically available information and attempts to capture an envisioned
8 Gbit single-die part (i.e. without TSVs).
|
|
This patch provides useful printouts throughut the memory system. This
includes pretty-printed cache tags and function call messages
(call-stack like).
|
|
This patch changes the SimpleTimingPort and RubyPort to panic on
inhibited requests as this should never happen in either of the
cases. The SimpleTimingPort is only used for the I/O devices PIO port
and the DMA devices config port and should thus never see an inhibited
request. Similarly, the SimpleTimingPort is also used for the
MessagePort in x86, and there should also not be any cases where the
port sees an inhibited request.
|
|
This changeset adds support for m5 pseudo-ops when running in
kvm-mode. Unfortunately, we can't trap the normal gem5 co-processor
entry in KVM (it doesn't seem to be possible to trap accesses to
non-existing co-processors). We therefore use BZJ instructions to
cause a trap from virtualized mode into gem5. The BZJ instruction is
becomes a normal branch to the gem5 fallback code when running in
simulated mode, which means that this patch does not need to change
the ARM ISA-specific code.
Note: This requires a patched host kernel.
|
|
All architectures execute m5 pseudo instructions by setting up
arguments according to the ABI and executing a magic instruction that
contains an operation number. Handling of such instructions is
currently spread across the different ISA implementations. This
changeset introduces the PseudoInst::pseudoInst function which handles
most of this in an architecture independent way. This is function is
mainly intended to be used from KVM, but can also be used from the
simulated CPUs.
|
|
|
|
Architecture specific limitations:
* LPAE is currently not supported by gem5. We therefore panic if LPAE
is enabled when returning to gem5.
* The co-processor based interface to the architected timer is
unsupported. We can't support this due to limitations in the KVM
API on ARM.
* M5 ops are currently not supported. This requires either a kernel
hack or a memory mapped device that handles the guest<->m5
interface.
|
|
Add the method checkRaw to ArmISA::Interrupts. This method can be used
to query the raw state (ignoring CPSR masks) of an interrupt. It is
primarily intended for hardware virtualized CPUs.
|
|
Add support for using the CPU cycle counter instead of a normal POSIX
timer to generate timed exits to gem5. This should, in theory, provide
better resolution when requesting timer signals.
The perf-based timer requires a fairly recent kernel since it requires
a working PERF_EVENT_IOC_PERIOD ioctl. This ioctl has existed in the
kernel for a long time, but it used to be completely broken due to an
inverted match when the kernel copied things from user
space. Additionally, the ioctl does not change the sample period
correctly on all kernel versions which implement it. It is currently
only known to work reliably on kernel version 3.7 and above on ARM.
|
