diff options
Diffstat (limited to 'include/configs/BSC9131RDB.h')
| -rw-r--r-- | include/configs/BSC9131RDB.h | 348 |
1 files changed, 0 insertions, 348 deletions
diff --git a/include/configs/BSC9131RDB.h b/include/configs/BSC9131RDB.h deleted file mode 100644 index b5d759c..0000000 --- a/include/configs/BSC9131RDB.h +++ /dev/null @@ -1,348 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2011-2012 Freescale Semiconductor, Inc. - */ - -/* - * BSC9131 RDB board configuration file - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_NAND_FSL_IFC - -#ifdef CONFIG_SPIFLASH -#define CONFIG_RAMBOOT_SPIFLASH -#define CONFIG_SYS_RAMBOOT -#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc -#endif - -#ifdef CONFIG_NAND -#define CONFIG_SPL_INIT_MINIMAL -#define CONFIG_SPL_FLUSH_IMAGE -#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" - -#define CONFIG_SPL_MAX_SIZE 8192 -#define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000 -#define CONFIG_SPL_RELOC_STACK 0x00100000 -#define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) - 0x2000) -#define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE) -#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 -#define CONFIG_SYS_NAND_U_BOOT_OFFS 0 -#endif - -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE -#else -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#endif - -/* High Level Configuration Options */ - -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on 9131 RDB */ -#if defined(CONFIG_SYS_CLK_100) -#define CONFIG_SYS_CLK_FREQ 100000000 /* SYSCLK for 9131 RDB */ -#else -#define CONFIG_SYS_CLK_FREQ 66666666 /* SYSCLK for 9131 RDB */ -#endif - -#define CONFIG_HWCONFIG -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* enable branch predition */ - -#define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x01ffffff - -/* DDR Setup */ -#undef CONFIG_SYS_DDR_RAW_TIMING -#undef CONFIG_DDR_SPD -#define CONFIG_SYS_SPD_BUS_NUM 0 -#define SPD_EEPROM_ADDRESS 0x52 /* I2C access */ - -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#ifndef __ASSEMBLY__ -extern unsigned long get_sdram_size(void); -#endif -#define CONFIG_SYS_SDRAM_SIZE get_sdram_size() /* DDR size */ -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE - -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL 1 - -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f -#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 -#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 - -#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef -#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 -#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 -#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 - -#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 -#define CONFIG_SYS_DDR_SR_CNTR 0x00000000 -#define CONFIG_SYS_DDR_RCW_1 0x00000000 -#define CONFIG_SYS_DDR_RCW_2 0x00000000 -#define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */ -#define CONFIG_SYS_DDR_CONTROL_2 0x24401000 -#define CONFIG_SYS_DDR_TIMING_4 0x00000001 -#define CONFIG_SYS_DDR_TIMING_5 0x02401400 - -#define CONFIG_SYS_DDR_TIMING_3_800 0x00030000 -#define CONFIG_SYS_DDR_TIMING_0_800 0x00110104 -#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b8644 -#define CONFIG_SYS_DDR_TIMING_2_800 0x0fa888cf -#define CONFIG_SYS_DDR_CLK_CTRL_800 0x03000000 -#define CONFIG_SYS_DDR_MODE_1_800 0x00441420 -#define CONFIG_SYS_DDR_MODE_2_800 0x8000c000 -#define CONFIG_SYS_DDR_INTERVAL_800 0x0c300100 -#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8675f608 - -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -/* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR CONFIG_SYS_CCSRBAR_DEFAULT -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR_DEFAULT - -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses */ - /* CONFIG_SYS_IMMR */ -/* DSP CCSRBAR */ -#define CONFIG_SYS_FSL_DSP_CCSRBAR CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT -#define CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT - -/* - * Memory map - * - * 0x0000_0000 0x3FFF_FFFF DDR 1G cacheable - * 0x8800_0000 0x8810_0000 IFC internal SRAM 1M - * 0xB000_0000 0xB0FF_FFFF DSP core M2 memory 16M - * 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M - * 0xC1F0_0000 0xC1F3_FFFF PA L2 SRAM Region 0 256K - * 0xC1F8_0000 0xC1F9_FFFF PA L2 SRAM Region 1 128K - * 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K - * 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M - * 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M - * 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND flash buffer 8M - * - */ - -/* - * IFC Definitions - */ - -/* NAND Flash on IFC */ -#define CONFIG_SYS_NAND_BASE 0xff800000 -#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE - -#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ - | CSPR_PORT_SIZE_8 /* Port Size = 8 bit*/ \ - | CSPR_MSEL_NAND /* MSEL = NAND */ \ - | CSPR_V) -#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) - -#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ - | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ - | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ - | CSOR_NAND_RAL_2 /* RAL = 2Byes */ \ - | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ - | CSOR_NAND_SPRZ_64 /* Spare size = 64 */ \ - | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ - -/* NAND Flash Timing Params */ -#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x03) \ - | FTIM0_NAND_TWP(0x05) \ - | FTIM0_NAND_TWCHT(0x02) \ - | FTIM0_NAND_TWH(0x04)) -#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x1C) \ - | FTIM1_NAND_TWBE(0x1E) \ - | FTIM1_NAND_TRR(0x07) \ - | FTIM1_NAND_TRP(0x05)) -#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x08) \ - | FTIM2_NAND_TREH(0x04) \ - | FTIM2_NAND_TWHRE(0x11)) -#define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x04) - -#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) - -#define CONFIG_SYS_NAND_DDR_LAW 11 - -/* Set up IFC registers for boot location NAND */ -#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR -#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK -#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR -#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 -#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 -#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 -#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 - -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* End of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \ - - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/ - -/* Serial Port */ -#undef CONFIG_SERIAL_SOFTWARE_FIFO -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#ifdef CONFIG_SPL_BUILD -#define CONFIG_NS16550_MIN_FUNCTIONS -#endif - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) - -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 - -/* I2C EEPROM */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 - -/* eSPI - Enhanced SPI */ - -#if defined(CONFIG_TSEC_ENET) - -#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "eTSEC1" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "eTSEC2" - -#define TSEC1_PHY_ADDR 0 -#define TSEC2_PHY_ADDR 3 - -#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) - -#define TSEC1_PHYIDX 0 - -#define TSEC2_PHYIDX 0 - -#define CONFIG_ETHPRIME "eTSEC1" - -#endif /* CONFIG_TSEC_ENET */ - -/* - * Environment - */ -#if defined(CONFIG_RAMBOOT_SPIFLASH) -#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ -#define CONFIG_ENV_SECT_SIZE 0x10000 -#define CONFIG_ENV_SIZE 0x2000 -#elif defined(CONFIG_NAND) -#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET ((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) -#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) -#elif defined(CONFIG_SYS_RAMBOOT) -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_LOADS_ECHO /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -#ifdef CONFIG_USB_EHCI_HCD -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET -#define CONFIG_USB_EHCI_FSL -#define CONFIG_HAS_FSL_DR_USB -#endif - -/* - * Dynamic MTD Partition support with mtdparts - */ - -/* - * Environment Configuration - */ - -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#endif - -#define CONFIG_HOSTNAME "BSC9131rdb" -#define CONFIG_ROOTPATH "/opt/nfsroot" -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "uboot=" CONFIG_UBOOTPATH "\0" \ - "loadaddr=1000000\0" \ - "bootfile=uImage\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=2000000\0" \ - "ramdiskfile=rootfs.ext2.gz.uboot\0" \ - "fdtaddr=1e00000\0" \ - "fdtfile=bsc9131rdb.dtb\0" \ - "bdev=sda1\0" \ - "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" \ - "bootm_size=0x37000000\0" \ - "othbootargs=ramdisk_size=600000 " \ - "default_hugepagesz=256m hugepagesz=256m hugepages=1\0" \ - "usbext2boot=setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs; " \ - "usb start;" \ - "ext2load usb 0:4 $loadaddr $bootfile;" \ - "ext2load usb 0:4 $fdtaddr $fdtfile;" \ - "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \ - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs; " \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND - -#endif /* __CONFIG_H */ |