diff options
Diffstat (limited to 'include/configs/M5208EVBE.h')
| -rw-r--r-- | include/configs/M5208EVBE.h | 181 |
1 files changed, 0 insertions, 181 deletions
diff --git a/include/configs/M5208EVBE.h b/include/configs/M5208EVBE.h deleted file mode 100644 index 0a356f4..0000000 --- a/include/configs/M5208EVBE.h +++ /dev/null @@ -1,181 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Configuation settings for the Freescale MCF5208EVBe. - * - * Copyright (C) 2004-2008 Freescale Semiconductor, Inc. - * TsiChung Liew (Tsi-Chung.Liew@freescale.com) - */ - -#ifndef _M5208EVBE_H -#define _M5208EVBE_H - -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_MCFUART -#define CONFIG_SYS_UART_PORT (0) - -#undef CONFIG_WATCHDOG -#define CONFIG_WATCHDOG_TIMEOUT 5000 - -#define CONFIG_MCFFEC -#ifdef CONFIG_MCFFEC -# define CONFIG_MII_INIT 1 -# define CONFIG_SYS_DISCOVER_PHY -# define CONFIG_SYS_RX_ETH_BUFFER 8 -# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN -# define CONFIG_HAS_ETH1 - -# define CONFIG_SYS_FEC0_PINMUX 0 -# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE -# define MCFFEC_TOUT_LOOP 50000 -/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ -# ifndef CONFIG_SYS_DISCOVER_PHY -# define FECDUPLEX FULL -# define FECSPEED _100BASET -# else -# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN -# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN -# endif -# endif /* CONFIG_SYS_DISCOVER_PHY */ -#endif - -/* Timer */ -#define CONFIG_MCFTMR -#undef CONFIG_MCFPIT - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 80000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 -#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR - -#define CONFIG_UDP_CHECKSUM - -#ifdef CONFIG_MCFFEC -# define CONFIG_IPADDR 192.162.1.2 -# define CONFIG_NETMASK 255.255.255.0 -# define CONFIG_SERVERIP 192.162.1.1 -# define CONFIG_GATEWAYIP 192.162.1.1 -#endif /* CONFIG_MCFFEC */ - -#define CONFIG_HOSTNAME "M5208EVBe" -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "loadaddr=40010000\0" \ - "u-boot=u-boot.bin\0" \ - "load=tftp ${loadaddr) ${u-boot}\0" \ - "upd=run load; run prog\0" \ - "prog=prot off 0 3ffff;" \ - "era 0 3ffff;" \ - "cp.b ${loadaddr} 0 ${filesize};" \ - "save\0" \ - "" - -#define CONFIG_PRAM 512 /* 512 KB */ - -#define CONFIG_SYS_LOAD_ADDR 0x40010000 - -#define CONFIG_SYS_CLK 166666666 /* CPU Core Clock */ -#define CONFIG_SYS_PLL_ODR 0x36 -#define CONFIG_SYS_PLL_FDR 0x7D - -#define CONFIG_SYS_MBAR 0xFC000000 - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/* Definitions for initial stack pointer and data area (in DPRAM) */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in internal SRAM */ -#define CONFIG_SYS_INIT_RAM_CTRL 0x221 -#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x40000000 -#define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */ -#define CONFIG_SYS_SDRAM_CFG1 0x43711630 -#define CONFIG_SYS_SDRAM_CFG2 0x56670000 -#define CONFIG_SYS_SDRAM_CTRL 0xE1002000 -#define CONFIG_SYS_SDRAM_EMOD 0x80010000 -#define CONFIG_SYS_SDRAM_MODE 0x00CD0000 - -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400 -#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) - -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ - -#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization ?? - */ -#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) -#define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20) - -/* FLASH organization */ -#ifdef CONFIG_SYS_FLASH_CFI -# define CONFIG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */ -# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT -# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -# define CONFIG_SYS_MAX_FLASH_SECT 254 /* max number of sectors on one chip */ -#endif - -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE - -/* - * Configuration for environment - * Environment is embedded in u-boot in the second sector of the flash - */ -#define CONFIG_ENV_OFFSET 0x2000 -#define CONFIG_ENV_SIZE 0x1000 -#define CONFIG_ENV_SECT_SIZE 0x2000 - -#define LDS_BOARD_TEXT \ - . = DEFINED(env_offset) ? env_offset : .; \ - env/embedded.o(.text*); - -/* Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 16 - -#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 8) -#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 4) -#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) -#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ - CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ - CF_ACR_EN | CF_ACR_SM_ALL) -#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ - CF_CACR_DISD | CF_CACR_INVI | \ - CF_CACR_CEIB | CF_CACR_DCM | \ - CF_CACR_EUSP) - -/* Chipselect bank definitions */ -/* - * CS0 - NOR Flash - * CS1 - Available - * CS2 - Available - * CS3 - Available - * CS4 - Available - * CS5 - Available - */ -#define CONFIG_SYS_CS0_BASE 0 -#define CONFIG_SYS_CS0_MASK 0x007F0001 -#define CONFIG_SYS_CS0_CTRL 0x00001FA0 - -#endif /* _M5208EVBE_H */ |