diff options
Diffstat (limited to 'include/configs/MPC8349EMDS_SDRAM.h')
| -rw-r--r-- | include/configs/MPC8349EMDS_SDRAM.h | 451 |
1 files changed, 0 insertions, 451 deletions
diff --git a/include/configs/MPC8349EMDS_SDRAM.h b/include/configs/MPC8349EMDS_SDRAM.h deleted file mode 100644 index 2ae1069..0000000 --- a/include/configs/MPC8349EMDS_SDRAM.h +++ /dev/null @@ -1,451 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2006-2010 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - */ - -/* - * mpc8349emds board configuration file - * - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 Family */ - -#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x00100000 - -/* - * DDR Setup - */ -#define CONFIG_DDR_ECC /* support DDR ECC function */ -#define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */ -#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/ - -/* - * SYS_FSL_DDR2 is selected in Kconfig to use unified DDR driver - * unselect it to use old spd_sdram.c - */ -#define CONFIG_SYS_SPD_BUS_NUM 0 -#define SPD_EEPROM_ADDRESS1 0x52 -#define SPD_EEPROM_ADDRESS2 0x51 -#define CONFIG_DIMM_SLOTS_PER_CTLR 2 -#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -/* - * 32-bit data path mode. - * - * Please note that using this mode for devices with the real density of 64-bit - * effectively reduces the amount of available memory due to the effect of - * wrapping around while translating address to row/columns, for example in the - * 256MB module the upper 128MB get aliased with contents of the lower - * 128MB); normally this define should be used for devices with real 32-bit - * data path. - */ -#undef CONFIG_DDR_32BIT - -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \ - | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) -#undef CONFIG_DDR_2T_TIMING - -/* - * DDRCDR - DDR Control Driver Register - */ -#define CONFIG_SYS_DDRCDR_VALUE 0x80080001 - -#if defined(CONFIG_SPD_EEPROM) -/* - * Determine DDR configuration from I2C interface. - */ -#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ -#else -/* - * Manually set up DDR parameters - */ -#define CONFIG_SYS_DDR_SIZE 256 /* MB */ -#if defined(CONFIG_DDR_II) -#define CONFIG_SYS_DDRCDR 0x80080001 -#define CONFIG_SYS_DDR_CS2_BNDS 0x0000000f -#define CONFIG_SYS_DDR_CS2_CONFIG 0x80330102 -#define CONFIG_SYS_DDR_TIMING_0 0x00220802 -#define CONFIG_SYS_DDR_TIMING_1 0x38357322 -#define CONFIG_SYS_DDR_TIMING_2 0x2f9048c8 -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 -#define CONFIG_SYS_DDR_CLK_CNTL 0x02000000 -#define CONFIG_SYS_DDR_MODE 0x47d00432 -#define CONFIG_SYS_DDR_MODE2 0x8000c000 -#define CONFIG_SYS_DDR_INTERVAL 0x03cf0080 -#define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000 -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 -#else -#define CONFIG_SYS_DDR_CS2_CONFIG (CSCONFIG_EN \ - | CSCONFIG_ROW_BIT_13 \ - | CSCONFIG_COL_BIT_10) -#define CONFIG_SYS_DDR_TIMING_1 0x36332321 -#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ -#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ -#define CONFIG_SYS_DDR_INTERVAL 0x04060100 /* autocharge,no open page */ - -#if defined(CONFIG_DDR_32BIT) -/* set burst length to 8 for 32-bit data path */ - /* DLL,normal,seq,4/2.5, 8 burst len */ -#define CONFIG_SYS_DDR_MODE 0x00000023 -#else -/* the default burst length is 4 - for 64-bit data path */ - /* DLL,normal,seq,4/2.5, 4 burst len */ -#define CONFIG_SYS_DDR_MODE 0x00000022 -#endif -#endif -#endif - -/* - * SDRAM on the Local Bus - */ -#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* Localbus SDRAM */ -#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ - -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */ -#define CONFIG_SYS_FLASH_SIZE 32 /* max flash size in MB */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -/* - * BCSR register on local bus 32KB, 8-bit wide for MDS config reg - */ -#define CONFIG_SYS_BCSR 0xE2400000 - /* Access window base at BCSR base */ -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ - -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */ - -/* - * The MPC834xEA MDS for 834xE rev3.1 may not be assembled SDRAM memory. - */ - -/* Local bus BR2, OR2 definition for SDRAM if soldered on the MDS board */ -/* - * Base Register 2 and Option Register 2 configure SDRAM. - * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. - * - * For BR2, need: - * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 - * port-size = 32-bits = BR2[19:20] = 11 - * no parity checking = BR2[21:22] = 00 - * SDRAM for MSEL = BR2[24:26] = 011 - * Valid = BR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861 - */ - -/* - * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. - * - * For OR2, need: - * 64MB mask for AM, OR2[0:7] = 1111 1100 - * XAM, OR2[17:18] = 11 - * 9 columns OR2[19-21] = 010 - * 13 rows OR2[23-25] = 100 - * EAD set for extra time OR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901 - */ - - - /* LB sdram refresh timer, about 6us */ -#define CONFIG_SYS_LBC_LSRT 0x32000000 - /* LB refresh timer prescal, 266MHz/32 */ -#define CONFIG_SYS_LBC_MRTPR 0x20000000 - -#define CONFIG_SYS_LBC_LSDMR_COMMON (LSDMR_RFEN \ - | LSDMR_BSMA1516 \ - | LSDMR_RFCR8 \ - | LSDMR_PRETOACT6 \ - | LSDMR_ACTTORW3 \ - | LSDMR_BL8 \ - | LSDMR_WRC3 \ - | LSDMR_CL3) - -/* - * SDRAM Controller configuration sequence. - */ -#define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL) -#define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) -#define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) -#define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW) -#define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL) - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } - -/* SPI */ -#undef CONFIG_SOFT_SPI /* SPI bit-banged */ - -/* GPIOs. Used as SPI chip selects */ -#define CONFIG_SYS_GPIO1_PRELIM -#define CONFIG_SYS_GPIO1_DIR 0xC0000000 /* SPI CS on 0, LED on 1 */ -#define CONFIG_SYS_GPIO1_DAT 0xC0000000 /* Both are active LOW */ - -/* TSEC */ -#define CONFIG_SYS_TSEC1_OFFSET 0x24000 -#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) -#define CONFIG_SYS_TSEC2_OFFSET 0x25000 -#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) - -/* USB */ -#define CONFIG_SYS_USE_MPC834XSYS_USB_PHY 1 /* Use SYS board PHY */ - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE -#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 -#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE -#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ - -#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000 -#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE -#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000 -#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE -#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI2_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000 -#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */ - -#if defined(CONFIG_PCI) - -#define CONFIG_83XX_PCI_STREAMING - -#undef CONFIG_EEPRO100 -#undef CONFIG_TULIP - -#if !defined(CONFIG_PCI_PNP) - #define PCI_ENET0_IOADDR 0xFIXME - #define PCI_ENET0_MEMADDR 0xFIXME - #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ -#endif - -#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ - -#endif /* CONFIG_PCI */ - -/* - * TSEC configuration - */ - -#if defined(CONFIG_TSEC_ENET) - -#define CONFIG_GMII 1 /* MII PHY management */ -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "TSEC1" -#define TSEC1_PHY_ADDR 0 -#define TSEC2_PHY_ADDR 1 -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC1_FLAGS TSEC_GIGABIT -#define TSEC2_FLAGS TSEC_GIGABIT - -/* Options are: TSEC[0-1] */ -#define CONFIG_ETHPRIME "TSEC0" - -#endif /* CONFIG_TSEC_ENET */ - -/* - * Configure on-board RTC - */ -#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ - -/* - * Environment - */ -#ifndef CONFIG_SYS_RAMBOOT - #define CONFIG_ENV_ADDR \ - (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) - #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ - #define CONFIG_ENV_SIZE 0x2000 - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#else - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) - #define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * Command line configuration. - */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ - /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ - -/* - * System performance - */ -#define CONFIG_SYS_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */ -#define CONFIG_SYS_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */ -#define CONFIG_SYS_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */ -#define CONFIG_SYS_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) */ - -/* System IO Config */ -#define CONFIG_SYS_SICRH 0 -#define CONFIG_SYS_SICRL SICRL_LDP_A - -#ifdef CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE -#endif - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ -#endif - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE - -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH1 -#define CONFIG_HAS_ETH0 -#endif - -#define CONFIG_HOSTNAME "mpc8349emds" -#define CONFIG_ROOTPATH "/nfsroot/rootfs" -#define CONFIG_BOOTFILE "uImage" - -#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=mpc8349emds\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0" \ - "update=protect off fe000000 fe03ffff; " \ - "era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0"\ - "upd=run load update\0" \ - "fdtaddr=780000\0" \ - "fdtfile=mpc834x_mds.dtb\0" \ - "" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ - "$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND "run flash_self" - -#endif /* __CONFIG_H */ |