diff options
Diffstat (limited to 'include/configs/MPC8349ITX.h')
| -rw-r--r-- | include/configs/MPC8349ITX.h | 454 |
1 files changed, 0 insertions, 454 deletions
diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h deleted file mode 100644 index c395d62..0000000 --- a/include/configs/MPC8349ITX.h +++ /dev/null @@ -1,454 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) Freescale Semiconductor, Inc. 2006. - */ - -/* - MPC8349E-mITX and MPC8349E-mITX-GP board configuration file - - Memory map: - - 0x0000_0000-0x0FFF_FFFF DDR SDRAM (256 MB) - 0x8000_0000-0x9FFF_FFFF PCI1 memory space (512 MB) - 0xA000_0000-0xBFFF_FFFF PCI2 memory space (512 MB) - 0xE000_0000-0xEFFF_FFFF IMMR (1 MB) - 0xE200_0000-0xE2FF_FFFF PCI1 I/O space (16 MB) - 0xE300_0000-0xE3FF_FFFF PCI2 I/O space (16 MB) - 0xF000_0000-0xF000_FFFF Compact Flash (MPC8349E-mITX only) - 0xF001_0000-0xF001_FFFF Local bus expansion slot - 0xF800_0000-0xF801_FFFF Vitesse 7385 Parallel Interface (MPC8349E-mITX only) - 0xFE00_0000-0xFE7F_FFFF First 8MB bank of Flash memory - 0xFE80_0000-0xFEFF_FFFF Second 8MB bank of Flash memory (MPC8349E-mITX only) - - I2C address list: - Align. Board - Bus Addr Part No. Description Length Location - ---------------------------------------------------------------- - I2C0 0x50 M24256-BWMN6P Board EEPROM 2 U64 - - I2C1 0x20 PCF8574 I2C Expander 0 U8 - I2C1 0x21 PCF8574 I2C Expander 0 U10 - I2C1 0x38 PCF8574A I2C Expander 0 U8 - I2C1 0x39 PCF8574A I2C Expander 0 U10 - I2C1 0x51 (DDR) DDR EEPROM 1 U1 - I2C1 0x68 DS1339 RTC 1 U68 - - Note that a given board has *either* a pair of 8574s or a pair of 8574As. -*/ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_MISC_INIT_F - -/* - * On-board devices - */ - -#ifdef CONFIG_TARGET_MPC8349ITX -/* The CF card interface on the back of the board */ -#define CONFIG_COMPACT_FLASH -#define CONFIG_VSC7385_ENET /* VSC7385 ethernet support */ -#define CONFIG_SYS_USB_HOST /* use the EHCI USB controller */ -#endif - -#define CONFIG_RTC_DS1337 -#define CONFIG_SYS_I2C - -/* - * Device configurations - */ - -/* I2C */ -#ifdef CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 - -#define CONFIG_SYS_SPD_BUS_NUM 1 /* The I2C bus for SPD */ -#define CONFIG_SYS_RTC_BUS_NUM 1 /* The I2C bus for RTC */ - -#define CONFIG_SYS_I2C_8574_ADDR1 0x20 /* I2C1, PCF8574 */ -#define CONFIG_SYS_I2C_8574_ADDR2 0x21 /* I2C1, PCF8574 */ -#define CONFIG_SYS_I2C_8574A_ADDR1 0x38 /* I2C1, PCF8574A */ -#define CONFIG_SYS_I2C_8574A_ADDR2 0x39 /* I2C1, PCF8574A */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* I2C0, Board EEPROM */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* I2C1, DS1339 RTC*/ -#define SPD_EEPROM_ADDRESS 0x51 /* I2C1, DDR */ - -/* Don't probe these addresses: */ -#define CONFIG_SYS_I2C_NOPROBES { {1, CONFIG_SYS_I2C_8574_ADDR1}, \ - {1, CONFIG_SYS_I2C_8574_ADDR2}, \ - {1, CONFIG_SYS_I2C_8574A_ADDR1}, \ - {1, CONFIG_SYS_I2C_8574A_ADDR2} } -/* Bit definitions for the 8574[A] I2C expander */ - /* Board revision, 00=0.0, 01=0.1, 10=1.0 */ -#define I2C_8574_REVISION 0x03 -#define I2C_8574_CF 0x08 /* 1=Compact flash absent, 0=present */ -#define I2C_8574_MPCICLKRN 0x10 /* MiniPCI Clk Run */ -#define I2C_8574_PCI66 0x20 /* 0=33MHz PCI, 1=66MHz PCI */ -#define I2C_8574_FLASHSIDE 0x40 /* 0=Reset vector from U4, 1=from U7*/ - -#endif - -/* Compact Flash */ -#ifdef CONFIG_COMPACT_FLASH - -#define CONFIG_SYS_IDE_MAXBUS 1 -#define CONFIG_SYS_IDE_MAXDEVICE 1 - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_CF_BASE -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 -#define CONFIG_SYS_ATA_REG_OFFSET 0 -#define CONFIG_SYS_ATA_ALT_OFFSET 0x0200 -#define CONFIG_SYS_ATA_STRIDE 2 - -/* If a CF card is not inserted, time out quickly */ -#define ATA_RESET_TIME 1 - -#endif - -/* - * SATA - */ -#ifdef CONFIG_SATA_SIL3114 - -#define CONFIG_SYS_SATA_MAX_DEVICE 4 -#define CONFIG_LBA48 - -#endif - -#ifdef CONFIG_SYS_USB_HOST -/* - * Support USB - */ -#define CONFIG_USB_EHCI_FSL - -/* Current USB implementation supports the only USB controller, - * so we have to choose between the MPH or the DR ones */ -#if 1 -#define CONFIG_HAS_FSL_MPH_USB -#else -#define CONFIG_HAS_FSL_DR_USB -#endif - -#endif - -/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CONFIG_SYS_83XX_DDR_USES_CS0 -#define CONFIG_SYS_MEMTEST_START 0x1000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x2000 - -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \ - | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075) - -#define CONFIG_VERY_BIG_RAM -#define CONFIG_MAX_MEM_MAPPED ((phys_size_t)256 << 20) - -#ifdef CONFIG_SYS_I2C -#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/ -#endif - -/* No SPD? Then manually set up DDR parameters */ -#ifndef CONFIG_SPD_EEPROM - #define CONFIG_SYS_DDR_SIZE 256 /* Mb */ - #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ - | CSCONFIG_ROW_BIT_13 \ - | CSCONFIG_COL_BIT_10) - - #define CONFIG_SYS_DDR_TIMING_1 0x26242321 - #define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45, may need tuning */ -#endif - -/* - *Flash on the Local Bus - */ - -#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */ -#define CONFIG_SYS_FLASH_EMPTY_INFO -/* 127 64KB sectors + 8 8KB sectors per device */ -#define CONFIG_SYS_MAX_FLASH_SECT 135 -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT - -/* The ITX has two flash chips, but the ITX-GP has only one. To support both -boards, we say we have two, but don't display a message if we find only one. */ -#define CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ -#define CONFIG_SYS_FLASH_BANKS_LIST \ - {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE + 0x800000} -#define CONFIG_SYS_FLASH_SIZE 16 /* FLASH size in MB */ - -/* Vitesse 7385 */ - -#ifdef CONFIG_VSC7385_ENET - -#define CONFIG_TSEC2 - -/* The flash address and size of the VSC7385 firmware image */ -#define CONFIG_VSC7385_IMAGE 0xFEFFE000 -#define CONFIG_VSC7385_IMAGE_SIZE 8192 - -#endif - -/* - * BRx, ORx, LBLAWBARx, and LBLAWARx - */ - - -/* Vitesse 7385 */ - -#define CONFIG_SYS_VSC7385_BASE 0xF8000000 - -#define CONFIG_SYS_LED_BASE 0xF9000000 - - -/* Compact Flash */ - -#ifdef CONFIG_COMPACT_FLASH - -#define CONFIG_SYS_CF_BASE 0xF0000000 - - -#endif - -/* - * U-Boot memory configuration - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ - -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */ - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -#define CONSOLE ttyS0 - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) - -/* - * PCI - */ -#ifdef CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE - -#define CONFIG_MPC83XX_PCI2 - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE -#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_MMIO_BASE \ - (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE) -#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE -#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16M */ - -#ifdef CONFIG_MPC83XX_PCI2 -#define CONFIG_SYS_PCI2_MEM_BASE \ - (CONFIG_SYS_PCI1_MMIO_BASE + CONFIG_SYS_PCI1_MMIO_SIZE) -#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE -#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI2_MMIO_BASE \ - (CONFIG_SYS_PCI2_MEM_BASE + CONFIG_SYS_PCI2_MEM_SIZE) -#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE -#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI2_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI2_IO_PHYS \ - (CONFIG_SYS_PCI1_IO_PHYS + CONFIG_SYS_PCI1_IO_SIZE) -#define CONFIG_SYS_PCI2_IO_SIZE 0x01000000 /* 16M */ -#endif - -#ifndef CONFIG_PCI_PNP - #define PCI_ENET0_IOADDR 0x00000000 - #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI2_MEM_BASE - #define PCI_IDSEL_NUMBER 0x0f /* IDSEL = AD15 */ -#endif - -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ - -#endif - -/* TSEC */ - -#ifdef CONFIG_TSEC_ENET -#define CONFIG_TSEC1 - -#ifdef CONFIG_TSEC1 -#define CONFIG_HAS_ETH0 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_SYS_TSEC1_OFFSET 0x24000 -#define TSEC1_PHY_ADDR 0x1c /* VSC8201 uses address 0x1c */ -#define TSEC1_PHYIDX 0 -#define TSEC1_FLAGS TSEC_GIGABIT -#endif - -#ifdef CONFIG_TSEC2 -#define CONFIG_HAS_ETH1 -#define CONFIG_TSEC2_NAME "TSEC1" -#define CONFIG_SYS_TSEC2_OFFSET 0x25000 - -#define TSEC2_PHY_ADDR 4 -#define TSEC2_PHYIDX 0 -#define TSEC2_FLAGS TSEC_GIGABIT -#endif - -#define CONFIG_ETHPRIME "Freescale TSEC" - -#endif - -/* - * Environment - */ -#define CONFIG_ENV_OVERWRITE - -#ifndef CONFIG_SYS_RAMBOOT - #define CONFIG_ENV_ADDR \ - (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) - #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) for environment */ - #define CONFIG_ENV_SIZE 0x2000 -#else - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) - #define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_LOADS_ECHO /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* Watchdog */ -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ - -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ -#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ - /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -/* - * System performance - */ -#define CONFIG_SYS_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */ -#define CONFIG_SYS_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) */ -#define CONFIG_SYS_SCCR_USBMPHCM 3 /* USB MPH controller's clock */ -#define CONFIG_SYS_SCCR_USBDRCM 0 /* USB DR controller's clock */ - -/* - * System IO Config - */ -/* Needed for gigabit to work on TSEC 1 */ -#define CONFIG_SYS_SICRH SICRH_TSOBI1 - /* USB DR as device + USB MPH as host */ -#define CONFIG_SYS_SICRL (SICRL_LDP_A | SICRL_USB1) - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ -#endif - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_NETDEV "eth0" - -/* Default path and filenames */ -#define CONFIG_ROOTPATH "/nfsroot/rootfs" -#define CONFIG_BOOTFILE "uImage" - /* U-Boot image on TFTP server */ -#define CONFIG_UBOOTPATH "u-boot.bin" - -#ifdef CONFIG_TARGET_MPC8349ITX -#define CONFIG_FDTFILE "mpc8349emitx.dtb" -#else -#define CONFIG_FDTFILE "mpc8349emitxgp.dtb" -#endif - - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "console=" __stringify(CONSOLE) "\0" \ - "netdev=" CONFIG_NETDEV "\0" \ - "uboot=" CONFIG_UBOOTPATH "\0" \ - "tftpflash=tftpboot $loadaddr $uboot; " \ - "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize; " \ - "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize\0" \ - "fdtaddr=780000\0" \ - "fdtfile=" CONFIG_FDTFILE "\0" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath" \ - " ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off "\ - " console=$console,$baudrate $othbootargs; " \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw" \ - " console=$console,$baudrate $othbootargs; " \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#endif |