diff options
Diffstat (limited to 'include/configs/MPC837XEMDS.h')
| -rw-r--r-- | include/configs/MPC837XEMDS.h | 390 |
1 files changed, 0 insertions, 390 deletions
diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h deleted file mode 100644 index 724f8af..0000000 --- a/include/configs/MPC837XEMDS.h +++ /dev/null @@ -1,390 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2007 Freescale Semiconductor, Inc. - * Dave Liu <daveliu@freescale.com> - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 family */ - -/* - * IP blocks clock configuration - */ -#define CONFIG_SYS_SCCR_TSEC1CM 1 /* CSB:eTSEC1 = 1:1 */ -#define CONFIG_SYS_SCCR_TSEC2CM 1 /* CSB:eTSEC2 = 1:1 */ -#define CONFIG_SYS_SCCR_SATACM SCCR_SATACM_2 /* CSB:SATA[0:3] = 2:1 */ - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRH 0x00000000 -#define CONFIG_SYS_SICRL 0x00000000 - -/* - * Output Buffer Impedance - */ -#define CONFIG_SYS_OBIR 0x31100000 - -#define CONFIG_HWCONFIG - -/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 -#define CONFIG_SYS_83XX_DDR_USES_CS0 -#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN \ - | DDRCDR_ODT \ - | DDRCDR_Q_DRN) - /* 0x80080001 */ /* ODT 150ohm on SoC */ - -#undef CONFIG_DDR_ECC /* support DDR ECC function */ -#undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ - -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ -#define CONFIG_NEVER_ASSERT_ODT_TO_CPU /* Never assert ODT to internal IOs */ - -#if defined(CONFIG_SPD_EEPROM) -#define SPD_EEPROM_ADDRESS 0x51 /* I2C address of DDR SODIMM SPD */ -#else -/* - * Manually set up DDR parameters - * WHITE ELECTRONIC DESIGNS - W3HG64M72EEU403PD4 SO-DIMM - * consist of nine chips from SAMSUNG K4T51083QE-ZC(L)D5 - */ -#define CONFIG_SYS_DDR_SIZE 512 /* MB */ -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001f -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ - | CSCONFIG_ODT_RD_NEVER /* ODT_RD to none */ \ - | CSCONFIG_ODT_WR_ONLY_CURRENT /* ODT_WR to CSn */ \ - | CSCONFIG_ROW_BIT_14 \ - | CSCONFIG_COL_BIT_10) - /* 0x80010202 */ -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 -#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ - | (0 << TIMING_CFG0_WRT_SHIFT) \ - | (0 << TIMING_CFG0_RRT_SHIFT) \ - | (0 << TIMING_CFG0_WWT_SHIFT) \ - | (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ - | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ - | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ - | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) - /* 0x00620802 */ -#define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \ - | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \ - | (3 << TIMING_CFG1_ACTTORW_SHIFT) \ - | (5 << TIMING_CFG1_CASLAT_SHIFT) \ - | (13 << TIMING_CFG1_REFREC_SHIFT) \ - | (3 << TIMING_CFG1_WRREC_SHIFT) \ - | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ - | (2 << TIMING_CFG1_WRTORD_SHIFT)) - /* 0x3935d322 */ -#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ - | (6 << TIMING_CFG2_CPO_SHIFT) \ - | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ - | (4 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ - | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ - | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ - | (8 << TIMING_CFG2_FOUR_ACT_SHIFT)) - /* 0x131088c8 */ -#define CONFIG_SYS_DDR_INTERVAL ((0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT) \ - | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) - /* 0x03E00100 */ -#define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000 -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */ -#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ - | (0x1432 << SDRAM_MODE_SD_SHIFT)) - /* ODT 150ohm CL=3, AL=1 on SDRAM */ -#define CONFIG_SYS_DDR_MODE2 0x00000000 -#endif - -/* - * Memory test - */ -#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ -#define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x00140000 - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -#define CONFIG_FSL_ELBC 1 - -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ -#define CONFIG_SYS_FLASH_SIZE 32 /* max FLASH size is 32M */ - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -/* - * BCSR on the Local Bus - */ -#define CONFIG_SYS_BCSR 0xF8000000 - /* Access window base at BCSR base */ - -/* - * NAND Flash on the Local Bus - */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_NAND_FSL_ELBC 1 - -#define CONFIG_SYS_NAND_BASE 0xE0600000 - - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } - -/* - * Config on-board RTC - */ -#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_SYS_PCI_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE -#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000 -#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE -#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000 -#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */ - -#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE -#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 -#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 - -#define CONFIG_SYS_PCIE1_BASE 0xA0000000 -#define CONFIG_SYS_PCIE1_CFG_BASE 0xA0000000 -#define CONFIG_SYS_PCIE1_CFG_SIZE 0x08000000 -#define CONFIG_SYS_PCIE1_MEM_BASE 0xA8000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA8000000 -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 -#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCIE1_IO_PHYS 0xB8000000 -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 - -#define CONFIG_SYS_PCIE2_BASE 0xC0000000 -#define CONFIG_SYS_PCIE2_CFG_BASE 0xC0000000 -#define CONFIG_SYS_PCIE2_CFG_SIZE 0x08000000 -#define CONFIG_SYS_PCIE2_MEM_BASE 0xC8000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC8000000 -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 -#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 -#define CONFIG_SYS_PCIE2_IO_PHYS 0xD8000000 -#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 - -#ifdef CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE -#ifndef __ASSEMBLY__ -extern int board_pci_host_broken(void); -#endif -#define CONFIG_PCIE -#define CONFIG_PQ_MDS_PIB 1 /* PQ MDS Platform IO Board */ - -#define CONFIG_HAS_FSL_DR_USB 1 /* fixup device tree for the DR USB */ -#define CONFIG_USB_EHCI_FSL -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET - -#undef CONFIG_EEPRO100 -#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ -#endif /* CONFIG_PCI */ - -/* - * TSEC - */ -#define CONFIG_SYS_TSEC1_OFFSET 0x24000 -#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) -#define CONFIG_SYS_TSEC2_OFFSET 0x25000 -#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) - -/* - * TSEC ethernet configuration - */ -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "eTSEC0" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "eTSEC1" -#define TSEC1_PHY_ADDR 2 -#define TSEC2_PHY_ADDR 3 -#define TSEC1_PHY_ADDR_SGMII 8 -#define TSEC2_PHY_ADDR_SGMII 4 -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) - -/* Options are: TSEC[0-1] */ -#define CONFIG_ETHPRIME "eTSEC1" - -/* SERDES */ -#define CONFIG_FSL_SERDES -#define CONFIG_FSL_SERDES1 0xe3000 -#define CONFIG_FSL_SERDES2 0xe3100 - -/* - * SATA - */ -#define CONFIG_SYS_SATA_MAX_DEVICE 2 -#define CONFIG_SATA1 -#define CONFIG_SYS_SATA1_OFFSET 0x18000 -#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET) -#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA -#define CONFIG_SATA2 -#define CONFIG_SYS_SATA2_OFFSET 0x19000 -#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET) -#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA - -#ifdef CONFIG_FSL_SATA -#define CONFIG_LBA48 -#endif - -/* - * Environment - */ -#ifndef CONFIG_SYS_RAMBOOT - #define CONFIG_ENV_ADDR \ - (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) - #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ - #define CONFIG_ENV_SIZE 0x2000 -#else - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) - #define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * Command line configuration. - */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#ifdef CONFIG_MMC -#define CONFIG_FSL_ESDHC_PIN_MUX -#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ -#endif - -/* - * Environment Configuration - */ - -#define CONFIG_ENV_OVERWRITE - -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#endif - -#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=1000000\0" \ - "ramdiskfile=ramfs.83xx\0" \ - "fdtaddr=780000\0" \ - "fdtfile=mpc8379_mds.dtb\0" \ - "" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ - "$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND - -#endif /* __CONFIG_H */ |