diff options
Diffstat (limited to 'include/configs/MPC837XERDB.h')
| -rw-r--r-- | include/configs/MPC837XERDB.h | 428 |
1 files changed, 0 insertions, 428 deletions
diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h deleted file mode 100644 index 37f51ba..0000000 --- a/include/configs/MPC837XERDB.h +++ /dev/null @@ -1,428 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2007 Freescale Semiconductor, Inc. - * Kevin Lam <kevin.lam@freescale.com> - * Joe D'Abbraccio <joe.d'abbraccio@freescale.com> - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 family */ - -#define CONFIG_HWCONFIG - -/* - * On-board devices - */ -#define CONFIG_VSC7385_ENET - -/* System performance - define the value i.e. CONFIG_SYS_XXX -*/ - -/* System Clock Configuration Register */ -#define CONFIG_SYS_SCCR_TSEC1CM 1 /* eTSEC1 clock mode (0-3) */ -#define CONFIG_SYS_SCCR_TSEC2CM 1 /* eTSEC2 clock mode (0-3) */ -#define CONFIG_SYS_SCCR_SATACM SCCR_SATACM_2 /* SATA1-4 clock mode (0-3) */ - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRH 0x08200000 -#define CONFIG_SYS_SICRL 0x00000000 - -/* - * Output Buffer Impedance - */ -#define CONFIG_SYS_OBIR 0x30100000 - -/* - * Device configurations - */ - -/* Vitesse 7385 */ - -#ifdef CONFIG_VSC7385_ENET - -#define CONFIG_TSEC2 - -/* The flash address and size of the VSC7385 firmware image */ -#define CONFIG_VSC7385_IMAGE 0xFE7FE000 -#define CONFIG_VSC7385_IMAGE_SIZE 8192 - -#endif - -/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x03000000 -#define CONFIG_SYS_83XX_DDR_USES_CS0 - -#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN | DDRCDR_ODT | DDRCDR_Q_DRN) - -#undef CONFIG_DDR_ECC /* support DDR ECC function */ -#undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ - -#undef CONFIG_NEVER_ASSERT_ODT_TO_CPU /* Never assert ODT to internal IOs */ - -/* - * Manually set up DDR parameters - */ -#define CONFIG_SYS_DDR_SIZE 256 /* MB */ -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ - | CSCONFIG_ODT_WR_ONLY_CURRENT \ - | CSCONFIG_ROW_BIT_13 \ - | CSCONFIG_COL_BIT_10) - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 -#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ - | (0 << TIMING_CFG0_WRT_SHIFT) \ - | (0 << TIMING_CFG0_RRT_SHIFT) \ - | (0 << TIMING_CFG0_WWT_SHIFT) \ - | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ - | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ - | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ - | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) - /* 0x00260802 */ /* DDR400 */ -#define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \ - | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \ - | (3 << TIMING_CFG1_ACTTORW_SHIFT) \ - | (7 << TIMING_CFG1_CASLAT_SHIFT) \ - | (13 << TIMING_CFG1_REFREC_SHIFT) \ - | (3 << TIMING_CFG1_WRREC_SHIFT) \ - | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ - | (2 << TIMING_CFG1_WRTORD_SHIFT)) - /* 0x3937d322 */ -#define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ - | (5 << TIMING_CFG2_CPO_SHIFT) \ - | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ - | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ - | (3 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ - | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ - | (8 << TIMING_CFG2_FOUR_ACT_SHIFT)) - /* 0x02984cc8 */ - -#define CONFIG_SYS_DDR_INTERVAL ((1024 << SDRAM_INTERVAL_REFINT_SHIFT) \ - | (0 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) - /* 0x06090100 */ - -#if defined(CONFIG_DDR_2T_TIMING) -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ - | SDRAM_CFG_SDRAM_TYPE_DDR2 \ - | SDRAM_CFG_32_BE \ - | SDRAM_CFG_2T_EN) - /* 0x43088000 */ -#else -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ - | SDRAM_CFG_SDRAM_TYPE_DDR2) - /* 0x43000000 */ -#endif -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */ -#define CONFIG_SYS_DDR_MODE ((0x0406 << SDRAM_MODE_ESD_SHIFT) \ - | (0x0442 << SDRAM_MODE_SD_SHIFT)) - /* 0x04400442 */ /* DDR400 */ -#define CONFIG_SYS_DDR_MODE2 0x00000000 - -/* - * Memory test - */ -#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ -#define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x0ef70010 - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -#define CONFIG_FSL_ELBC 1 - -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ -#define CONFIG_SYS_FLASH_SIZE 8 /* max FLASH size is 32M */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */ - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -/* - * NAND Flash on the Local Bus - */ -#define CONFIG_SYS_NAND_BASE 0xE0600000 - - -/* Vitesse 7385 */ - -#define CONFIG_SYS_VSC7385_BASE 0xF0000000 - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* SERDES */ -#define CONFIG_FSL_SERDES -#define CONFIG_FSL_SERDES1 0xe3000 -#define CONFIG_FSL_SERDES2 0xe3100 - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } - -/* - * Config on-board RTC - */ -#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_SYS_PCI_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE -#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000 -#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE -#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000 -#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */ - -#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE -#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 -#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 - -#define CONFIG_SYS_PCIE1_BASE 0xA0000000 -#define CONFIG_SYS_PCIE1_CFG_BASE 0xA0000000 -#define CONFIG_SYS_PCIE1_CFG_SIZE 0x08000000 -#define CONFIG_SYS_PCIE1_MEM_BASE 0xA8000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA8000000 -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 -#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCIE1_IO_PHYS 0xB8000000 -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 - -#define CONFIG_SYS_PCIE2_BASE 0xC0000000 -#define CONFIG_SYS_PCIE2_CFG_BASE 0xC0000000 -#define CONFIG_SYS_PCIE2_CFG_SIZE 0x08000000 -#define CONFIG_SYS_PCIE2_MEM_BASE 0xC8000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC8000000 -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 -#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 -#define CONFIG_SYS_PCIE2_IO_PHYS 0xD8000000 -#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 - -#ifdef CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE - -#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ -#endif /* CONFIG_PCI */ - -/* - * TSEC - */ -#ifdef CONFIG_TSEC_ENET - -#define CONFIG_GMII /* MII PHY management */ - -#define CONFIG_TSEC1 - -#ifdef CONFIG_TSEC1 -#define CONFIG_HAS_ETH0 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_SYS_TSEC1_OFFSET 0x24000 -#define TSEC1_PHY_ADDR 2 -#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC1_PHYIDX 0 -#endif - -#ifdef CONFIG_TSEC2 -#define CONFIG_HAS_ETH1 -#define CONFIG_TSEC2_NAME "TSEC1" -#define CONFIG_SYS_TSEC2_OFFSET 0x25000 -#define TSEC2_PHY_ADDR 0x1c -#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC2_PHYIDX 0 -#endif - -/* Options are: TSEC[0-1] */ -#define CONFIG_ETHPRIME "TSEC0" - -#endif - -/* - * SATA - */ -#define CONFIG_SYS_SATA_MAX_DEVICE 2 -#define CONFIG_SATA1 -#define CONFIG_SYS_SATA1_OFFSET 0x18000 -#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET) -#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA -#define CONFIG_SATA2 -#define CONFIG_SYS_SATA2_OFFSET 0x19000 -#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET) -#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA - -#ifdef CONFIG_FSL_SATA -#define CONFIG_LBA48 -#endif - -/* - * Environment - */ -#ifndef CONFIG_SYS_RAMBOOT - #define CONFIG_ENV_ADDR \ - (CONFIG_SYS_MONITOR_BASE+CONFIG_SYS_MONITOR_LEN) - #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) for env */ - #define CONFIG_ENV_SIZE 0x4000 -#else - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-0x1000) - #define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * Command line configuration. - */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#ifdef CONFIG_MMC -#define CONFIG_FSL_ESDHC_PIN_MUX -#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ -#endif - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_HAS_FSL_DR_USB -#define CONFIG_USB_EHCI_FSL -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET - -#define CONFIG_NETDEV "eth1" - -#define CONFIG_HOSTNAME "mpc837x_rdb" -#define CONFIG_ROOTPATH "/nfsroot" -#define CONFIG_RAMDISKFILE "rootfs.ext2.gz.uboot" -#define CONFIG_BOOTFILE "uImage" - /* U-Boot image on TFTP server */ -#define CONFIG_UBOOTPATH "u-boot.bin" -#define CONFIG_FDTFILE "mpc8379_rdb.dtb" - - /* default location for tftp and bootm */ -#define CONFIG_LOADADDR 800000 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=" CONFIG_NETDEV "\0" \ - "uboot=" CONFIG_UBOOTPATH "\0" \ - "tftpflash=tftp $loadaddr $uboot;" \ - "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize; " \ - "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize\0" \ - "fdtaddr=780000\0" \ - "fdtfile=" CONFIG_FDTFILE "\0" \ - "ramdiskaddr=1000000\0" \ - "ramdiskfile=" CONFIG_RAMDISKFILE "\0" \ - "console=ttyS0\0" \ - "setbootargs=setenv bootargs " \ - "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \ - "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ - "$netdev:off " \ - "root=$rootdev rw console=$console,$baudrate $othbootargs\0" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv rootdev /dev/nfs;" \ - "run setbootargs;" \ - "run setipargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv rootdev /dev/ram;" \ - "run setbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#endif /* __CONFIG_H */ |