diff options
Diffstat (limited to 'include/configs/MPC8544DS.h')
| -rw-r--r-- | include/configs/MPC8544DS.h | 422 |
1 files changed, 0 insertions, 422 deletions
diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h deleted file mode 100644 index 2cbe855..0000000 --- a/include/configs/MPC8544DS.h +++ /dev/null @@ -1,422 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2007, 2010-2011 Freescale Semiconductor, Inc. - */ - -/* - * mpc8544ds board configuration file - * - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_PCI1 1 /* PCI controller 1 */ -#define CONFIG_PCIE1 1 /* PCIE controller 1 (slot 1) */ -#define CONFIG_PCIE2 1 /* PCIE controller 2 (slot 2) */ -#define CONFIG_PCIE3 1 /* PCIE controller 3 (ULI bridge) */ -#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ -#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ -#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ - -#define CONFIG_ENV_OVERWRITE -#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ - -#ifndef __ASSEMBLY__ -extern unsigned long get_board_sys_clk(unsigned long dummy); -#endif -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ - -/* - * Only possible on E500 Version 2 or newer cores. - */ -#define CONFIG_ENABLE_36BIT_PHYS 1 - -#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00400000 - -#define CONFIG_SYS_CCSRBAR 0xe0000000 -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR - -/* DDR Setup */ -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ -#define CONFIG_DDR_SPD - -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE -#define CONFIG_VERY_BIG_RAM - -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL 2 - -/* I2C addresses of SPD EEPROMs */ -#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ - -/* Make sure required options are set */ -#ifndef CONFIG_SPD_EEPROM -#error ("CONFIG_SPD_EEPROM is required") -#endif - -#undef CONFIG_CLOCKS_IN_MHZ - -/* - * Memory map - * - * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable - * - * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable - * - * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable - * - * 0xe000_0000 0xe00f_ffff CCSR 1M non-cacheable - * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable - * - * Localbus cacheable - * - * 0xf000_0000 0xf3ff_ffff SDRAM 64M Cacheable - * 0xf401_0000 0xf401_3fff L1 for stack 4K Cacheable TLB0 - * - * Localbus non-cacheable - * - * 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M non-cacheable - * 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M non-cacheable - * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M non-cacheable - * - */ - -/* - * Local Bus Definitions - */ -#define CONFIG_SYS_BOOT_BLOCK 0xfc000000 /* boot TLB */ - -#define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */ - -#define CONFIG_SYS_BR0_PRELIM 0xff801001 -#define CONFIG_SYS_BR1_PRELIM 0xfe801001 - -#define CONFIG_SYS_OR0_PRELIM 0xff806e65 -#define CONFIG_SYS_OR1_PRELIM 0xff806e65 - -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} - -#define CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO - -#define CONFIG_SYS_LBC_NONCACHE_BASE 0xf8000000 - -#define CONFIG_SYS_BR2_PRELIM 0xf8201001 /* port size 16bit */ -#define CONFIG_SYS_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/ - -#define CONFIG_SYS_BR3_PRELIM 0xf8100801 /* port size 8bit */ -#define CONFIG_SYS_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ - -#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ -#define PIXIS_BASE 0xf8100000 /* PIXIS registers */ -#define PIXIS_ID 0x0 /* Board ID at offset 0 */ -#define PIXIS_VER 0x1 /* Board version at offset 1 */ -#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ -#define PIXIS_RST 0x4 /* PIXIS Reset Control register */ -#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch - * register */ -#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ -#define PIXIS_VCTL 0x10 /* VELA Control Register */ -#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ -#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ -#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ -#define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */ -#define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */ -#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ -#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ -#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ -#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ -#define PIXIS_VSPEED2 0x1d /* VELA VSpeed 2 */ -#define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ -#define PIXIS_VSPEED2_TSEC1SER 0x2 -#define PIXIS_VSPEED2_TSEC3SER 0x1 -#define PIXIS_VCFGEN1_TSEC1SER 0x20 -#define PIXIS_VCFGEN1_TSEC3SER 0x40 -#define PIXIS_VSPEED2_MASK (PIXIS_VSPEED2_TSEC1SER|PIXIS_VSPEED2_TSEC3SER) -#define PIXIS_VCFGEN1_MASK (PIXIS_VCFGEN1_TSEC1SER|PIXIS_VCFGEN1_TSEC3SER) - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xf4010000 /* Initial L1 address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ - -/* Serial Port - controlled on board with jumper J8 - * open - index 2 - * shorted - index 1 - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 - -/* - * General PCI - * Memory space is mapped 1-1, but I/O space must start from 0. - */ -#define CONFIG_SYS_PCIE_VIRT 0x80000000 /* 1G PCIE TLB */ -#define CONFIG_SYS_PCIE_PHYS 0x80000000 /* 1G PCIE TLB */ -#define CONFIG_SYS_PCI_VIRT 0xc0000000 /* 512M PCI TLB */ -#define CONFIG_SYS_PCI_PHYS 0xc0000000 /* 512M PCI TLB */ - -#define CONFIG_SYS_PCI1_MEM_VIRT 0xc0000000 -#define CONFIG_SYS_PCI1_MEM_BUS 0xc0000000 -#define CONFIG_SYS_PCI1_MEM_PHYS 0xc0000000 -#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI1_IO_VIRT 0xe1000000 -#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64k */ - -/* controller 2, Slot 1, tgtid 1, Base address 9000 */ -#define CONFIG_SYS_PCIE2_NAME "Slot 1" -#define CONFIG_SYS_PCIE2_MEM_VIRT 0x80000000 -#define CONFIG_SYS_PCIE2_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS 0x80000000 -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE2_IO_VIRT 0xe1010000 -#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE2_IO_PHYS 0xe1010000 -#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ - -/* controller 1, Slot 2,tgtid 2, Base address a000 */ -#define CONFIG_SYS_PCIE1_NAME "Slot 2" -#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 -#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCIE1_IO_VIRT 0xe1020000 -#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE1_IO_PHYS 0xe1020000 -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ - -/* controller 3, direct to uli, tgtid 3, Base address b000 */ -#define CONFIG_SYS_PCIE3_NAME "ULI" -#define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 -#define CONFIG_SYS_PCIE3_MEM_BUS 0xb0000000 -#define CONFIG_SYS_PCIE3_MEM_PHYS 0xb0000000 -#define CONFIG_SYS_PCIE3_MEM_SIZE 0x00100000 /* 1M */ -#define CONFIG_SYS_PCIE3_IO_VIRT 0xb0100000 /* reuse mem LAW */ -#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE3_IO_PHYS 0xb0100000 /* reuse mem LAW */ -#define CONFIG_SYS_PCIE3_IO_SIZE 0x00100000 /* 1M */ -#define CONFIG_SYS_PCIE3_MEM_VIRT2 0xb0200000 -#define CONFIG_SYS_PCIE3_MEM_BUS2 0xb0200000 -#define CONFIG_SYS_PCIE3_MEM_PHYS2 0xb0200000 -#define CONFIG_SYS_PCIE3_MEM_SIZE2 0x00200000 /* 1M */ - -#if defined(CONFIG_PCI) - -/*PCIE video card used*/ -#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT - -/*PCI video card used*/ -/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_VIRT*/ - -/* video */ - -#if defined(CONFIG_VIDEO) -#define CONFIG_BIOSEMU -#define CONFIG_ATI_RADEON_FB -#define CONFIG_VIDEO_LOGO -#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET -#endif - -#undef CONFIG_EEPRO100 -#undef CONFIG_TULIP - -#ifndef CONFIG_PCI_PNP - #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BUS - #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_IO_BUS - #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */ -#endif - -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ - -#ifdef CONFIG_SCSI_AHCI -#define CONFIG_SATA_ULI5288 -#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 -#define CONFIG_SYS_SCSI_MAX_LUN 1 -#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) -#endif /* CONFIG_SCSI_AHCI */ - -#endif /* CONFIG_PCI */ - -#if defined(CONFIG_TSEC_ENET) - -#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "eTSEC1" -#define CONFIG_TSEC3 1 -#define CONFIG_TSEC3_NAME "eTSEC3" - -#define CONFIG_PIXIS_SGMII_CMD -#define CONFIG_FSL_SGMII_RISER 1 -#define SGMII_RISER_PHY_OFFSET 0x1c - -#define TSEC1_PHY_ADDR 0 -#define TSEC3_PHY_ADDR 1 - -#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) - -#define TSEC1_PHYIDX 0 -#define TSEC3_PHYIDX 0 - -#define CONFIG_ETHPRIME "eTSEC1" -#endif /* CONFIG_TSEC_ENET */ - -/* - * Environment - */ -#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) */ -#if CONFIG_SYS_MONITOR_BASE > 0xfff80000 -#define CONFIG_ENV_ADDR 0xfff80000 -#else -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) -#endif -#define CONFIG_ENV_SIZE 0x2000 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * USB - */ - -#ifdef CONFIG_USB_EHCI_HCD -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET -#define CONFIG_PCI_EHCI_DEVICE 0 -#endif - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Environment Configuration - */ - -/* The mac addresses for all ethernet interface */ -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#endif - -#define CONFIG_IPADDR 192.168.1.251 - -#define CONFIG_HOSTNAME "8544ds_unknown" -#define CONFIG_ROOTPATH "/nfs/mpc85xx" -#define CONFIG_BOOTFILE "8544ds/uImage.uboot" -#define CONFIG_UBOOTPATH 8544ds/u-boot.bin /* TFTP server */ - -#define CONFIG_SERVERIP 192.168.1.1 -#define CONFIG_GATEWAYIP 192.168.1.1 -#define CONFIG_NETMASK 255.255.0.0 - -#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/ - -#define CONFIG_EXTRA_ENV_SETTINGS \ -"netdev=eth0\0" \ -"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ -"tftpflash=tftpboot $loadaddr $uboot; " \ - "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize; " \ - "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize\0" \ -"consoledev=ttyS0\0" \ -"ramdiskaddr=2000000\0" \ -"ramdiskfile=8544ds/ramdisk.uboot\0" \ -"fdtaddr=1e00000\0" \ -"fdtfile=8544ds/mpc8544ds.dtb\0" \ -"bdev=sda3\0" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND \ - "setenv bootargs root=/dev/$bdev rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#endif /* __CONFIG_H */ |