summaryrefslogtreecommitdiff
path: root/include/configs/MPC8568MDS.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/MPC8568MDS.h')
-rw-r--r--include/configs/MPC8568MDS.h411
1 files changed, 0 insertions, 411 deletions
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
deleted file mode 100644
index 01ee69c..0000000
--- a/include/configs/MPC8568MDS.h
+++ /dev/null
@@ -1,411 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2004-2007, 2010-2011 Freescale Semiconductor.
- */
-
-/*
- * mpc8568mds board configuration file
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_SYS_SRIO
-#define CONFIG_SRIO1 /* SRIO port 1 */
-
-#define CONFIG_PCI1 1 /* PCI controller */
-#define CONFIG_PCIE1 1 /* PCIE controller */
-#define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-#define CONFIG_ENV_OVERWRITE
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_clock_freq(void);
-#endif /*Replace a call to get_clock_freq (after it is implemented)*/
-#define CONFIG_SYS_CLK_FREQ 66000000 /*TODO: restore if wanting to read from BCSR: get_clock_freq()*/ /* sysclk for MPC85xx */
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-
-/*
- * Only possible on E500 Version 2 or newer cores.
- */
-#define CONFIG_ENABLE_36BIT_PHYS 1
-
-#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00400000
-
-#define CONFIG_SYS_CCSRBAR 0xe0000000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-
-/* DDR Setup */
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_SPD
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
-
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-
-/* I2C addresses of SPD EEPROMs */
-#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
-
-/* Make sure required options are set */
-#ifndef CONFIG_SPD_EEPROM
-#error ("CONFIG_SPD_EEPROM is required")
-#endif
-
-#undef CONFIG_CLOCKS_IN_MHZ
-
-/*
- * Local Bus Definitions
- */
-
-/*
- * FLASH on the Local Bus
- * Two banks, 8M each, using the CFI driver.
- * Boot from BR0/OR0 bank at 0xff00_0000
- * Alternate BR1/OR1 bank at 0xff80_0000
- *
- * BR0, BR1:
- * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
- * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
- * Port Size = 16 bits = BRx[19:20] = 10
- * Use GPCM = BRx[24:26] = 000
- * Valid = BRx[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0
- * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1
- *
- * OR0, OR1:
- * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
- * Reserved ORx[17:18] = 11, confusion here?
- * CSNT = ORx[20] = 1
- * ACS = half cycle delay = ORx[21:22] = 11
- * SCY = 6 = ORx[24:27] = 0110
- * TRLX = use relaxed timing = ORx[29] = 1
- * EAD = use external address latch delay = OR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx
- */
-#define CONFIG_SYS_BCSR_BASE 0xf8000000
-
-#define CONFIG_SYS_FLASH_BASE 0xfe000000 /* start of FLASH 32M */
-
-/*Chip select 0 - Flash*/
-#define CONFIG_SYS_BR0_PRELIM 0xfe001001
-#define CONFIG_SYS_OR0_PRELIM 0xfe006ff7
-
-/*Chip slelect 1 - BCSR*/
-#define CONFIG_SYS_BR1_PRELIM 0xf8000801
-#define CONFIG_SYS_OR1_PRELIM 0xffffe9f7
-
-/*#define CONFIG_SYS_FLASH_BANKS_LIST {0xff800000, CONFIG_SYS_FLASH_BASE} */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-/*
- * SDRAM on the LocalBus
- */
-#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
-#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-
-/*Chip select 2 - SDRAM*/
-#define CONFIG_SYS_BR2_PRELIM 0xf0001861
-#define CONFIG_SYS_OR2_PRELIM 0xfc006901
-
-#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
-#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
-#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
-#define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
-
-/*
- * Common settings for all Local Bus SDRAM commands.
- * At run time, either BSMA1516 (for CPU 1.1)
- * or BSMA1617 (for CPU 1.0) (old)
- * is OR'ed in too.
- */
-#define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \
- | LSDMR_PRETOACT7 \
- | LSDMR_ACTTORW7 \
- | LSDMR_BL8 \
- | LSDMR_WRC4 \
- | LSDMR_CL3 \
- | LSDMR_RFEN \
- )
-
-/*
- * The bcsr registers are connected to CS3 on MDS.
- * The new memory map places bcsr at 0xf8000000.
- *
- * For BR3, need:
- * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
- * port-size = 8-bits = BR[19:20] = 01
- * no parity checking = BR[21:22] = 00
- * GPMC for MSEL = BR[24:26] = 000
- * Valid = BR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
- *
- * For OR3, need:
- * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0
- * disable buffer ctrl OR[19] = 0
- * CSNT OR[20] = 1
- * ACS OR[21:22] = 11
- * XACS OR[23] = 1
- * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe
- * SETA OR[28] = 0
- * TRLX OR[29] = 1
- * EHTR OR[30] = 1
- * EAD extra time OR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
- */
-#define CONFIG_SYS_BCSR (0xf8000000)
-
-/*Chip slelect 4 - PIB*/
-#define CONFIG_SYS_BR4_PRELIM 0xf8008801
-#define CONFIG_SYS_OR4_PRELIM 0xffffe9f7
-
-/*Chip select 5 - PIB*/
-#define CONFIG_SYS_BR5_PRELIM 0xf8010801
-#define CONFIG_SYS_OR5_PRELIM 0xffff69f7
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
-
-/* Serial Port */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
-
-/*
- * General PCI
- * Memory Addresses are mapped 1-1. I/O is mapped from 0
- */
-#define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000
-#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000
-#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000
-#define CONFIG_SYS_PCI1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
-#define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 8M */
-
-#define CONFIG_SYS_PCIE1_NAME "Slot"
-#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT 0xe2800000
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
-
-#define CONFIG_SYS_SRIO1_MEM_VIRT 0xC0000000
-#define CONFIG_SYS_SRIO1_MEM_BUS 0xC0000000
-#define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_BUS
-#define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */
-
-#ifdef CONFIG_QE
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#ifndef CONFIG_TSEC_ENET
-#define CONFIG_ETHPRIME "UEC0"
-#endif
-#define CONFIG_PHY_MODE_NEED_CHANGE
-#define CONFIG_eTSEC_MDIO_BUS
-
-#ifdef CONFIG_eTSEC_MDIO_BUS
-#define CONFIG_MIIM_ADDRESS 0xE0024520
-#endif
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK16
-#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 7
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
-#endif
-
-#define CONFIG_UEC_ETH2 /* GETH2 */
-
-#ifdef CONFIG_UEC_ETH2
-#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */
-#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE
-#define CONFIG_SYS_UEC2_TX_CLK QE_CLK16
-#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH
-#define CONFIG_SYS_UEC2_PHY_ADDR 1
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
-#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
-#endif
-#endif /* CONFIG_QE */
-
-#if defined(CONFIG_PCI)
-#undef CONFIG_EEPRO100
-#undef CONFIG_TULIP
-
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-
-#endif /* CONFIG_PCI */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC0"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC1"
-
-#define TSEC1_PHY_ADDR 2
-#define TSEC2_PHY_ADDR 3
-
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-
-#define TSEC1_FLAGS TSEC_GIGABIT
-#define TSEC2_FLAGS TSEC_GIGABIT
-
-/* Options are: eTSEC[0-1] */
-#define CONFIG_ETHPRIME "eTSEC0"
-
-#endif /* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-/* The mac addresses for all ethernet interface */
-#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#define CONFIG_HAS_ETH3
-#endif
-
-#define CONFIG_IPADDR 192.168.1.253
-
-#define CONFIG_HOSTNAME "unknown"
-#define CONFIG_ROOTPATH "/nfsroot"
-#define CONFIG_BOOTFILE "your.uImage"
-
-#define CONFIG_SERVERIP 192.168.1.1
-#define CONFIG_GATEWAYIP 192.168.1.1
-#define CONFIG_NETMASK 255.255.255.0
-
-#define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=600000\0" \
- "ramdiskfile=your.ramdisk.u-boot\0" \
- "fdtaddr=400000\0" \
- "fdtfile=your.fdt.dtb\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs\0" \
- "ramargs=setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs\0" \
-
-#define CONFIG_NFSBOOTCOMMAND \
- "run nfsargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "run ramargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "bootm $loadaddr $ramdiskaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
-
-#endif /* __CONFIG_H */
generated by cgit v1.2.3 (git 2.25.1) at 2024-05-02 05:17:25 +0000