diff options
Diffstat (limited to 'include/configs/caddy2.h')
| -rw-r--r-- | include/configs/caddy2.h | 333 |
1 files changed, 0 insertions, 333 deletions
diff --git a/include/configs/caddy2.h b/include/configs/caddy2.h deleted file mode 100644 index 89deeac..0000000 --- a/include/configs/caddy2.h +++ /dev/null @@ -1,333 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * esd vme8349 U-Boot configuration file - * Copyright (c) 2008, 2009 esd gmbh Hannover Germany - * - * (C) Copyright 2006-2010 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * reinhard.arlt@esd-electronics.de - * Based on the MPC8349EMDS config. - */ - -/* - * vme8349 board configuration file. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 Family */ - -/* Don't enable PCI2 on vme834x - it doesn't exist physically. */ -#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */ - -#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x00100000 - -/* - * DDR Setup - */ -#define CONFIG_DDR_ECC /* only for ECC DDR module */ -#define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */ -#define CONFIG_SPD_EEPROM -#define SPD_EEPROM_ADDRESS 0x54 -#define CONFIG_SYS_READ_SPD vme8349_read_spd -#define CONFIG_SYS_83XX_DDR_USES_CS0 /* esd; Fsl board uses CS2/CS3 */ - -/* - * 32-bit data path mode. - * - * Please note that using this mode for devices with the real density of 64-bit - * effectively reduces the amount of available memory due to the effect of - * wrapping around while translating address to row/columns, for example in the - * 256MB module the upper 128MB get aliased with contents of the lower - * 128MB); normally this define should be used for devices with real 32-bit - * data path. - */ -#undef CONFIG_DDR_32BIT - -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is sys memory*/ -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \ - | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075) -#define CONFIG_DDR_2T_TIMING -#define CONFIG_SYS_DDRCDR (DDRCDR_DHC_EN \ - | DDRCDR_ODT \ - | DDRCDR_Q_DRN) - /* 0x80080001 */ - -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_BASE 0xffc00000 /* start of FLASH */ -#define CONFIG_SYS_FLASH_SIZE 4 /* flash size in MB */ - - -#define CONFIG_SYS_WINDOW1_BASE 0xf0000000 - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device*/ - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase TO (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write TO (ms) */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xF7000000 /* Initial RAM addr */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* size */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Malloc size */ - -#undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */ - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } -/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */ - -#define CONFIG_SYS_I2C_8574_ADDR2 0x20 /* I2C1, PCF8574 */ - -/* TSEC */ -#define CONFIG_SYS_TSEC1_OFFSET 0x24000 -#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET) -#define CONFIG_SYS_TSEC2_OFFSET 0x25000 -#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET) - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE -#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 -#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE -#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ - -#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000 -#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE -#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000 -#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE -#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI2_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000 -#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */ - -#if defined(CONFIG_PCI) - -#undef CONFIG_EEPRO100 -#undef CONFIG_TULIP - -#if !defined(CONFIG_PCI_PNP) - #define PCI_ENET0_IOADDR 0xFIXME - #define PCI_ENET0_MEMADDR 0xFIXME - #define PCI_IDSEL_NUMBER 0xFIXME -#endif - -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ - -#endif /* CONFIG_PCI */ - -/* - * TSEC configuration - */ - -#if defined(CONFIG_TSEC_ENET) - -#define CONFIG_GMII /* MII PHY management */ -#define CONFIG_TSEC1 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_TSEC2 -#define CONFIG_TSEC2_NAME "TSEC1" -#define CONFIG_PHY_M88E1111 -#define TSEC1_PHY_ADDR 0x08 -#define TSEC2_PHY_ADDR 0x10 -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC1_FLAGS TSEC_GIGABIT -#define TSEC2_FLAGS TSEC_GIGABIT - -/* Options are: TSEC[0-1] */ -#define CONFIG_ETHPRIME "TSEC0" - -#endif /* CONFIG_TSEC_ENET */ - -/* - * Environment - */ -#ifndef CONFIG_SYS_RAMBOOT - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0xc0000) - #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ - #define CONFIG_ENV_SIZE 0x2000 - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#else - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) - #define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_LOADS_ECHO /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * Command line configuration. - */ -#define CONFIG_SYS_RTC_BUS_NUM 0x01 -#define CONFIG_SYS_I2C_RTC_ADDR 0x32 - -/* Pass Ethernet MAC to VxWorks */ -#define CONFIG_SYS_VXWORKS_MAC_PTR 0x000043f0 - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Init Memory map for Linux*/ - -#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ - -/* System IO Config */ -#define CONFIG_SYS_SICRH 0 -#define CONFIG_SYS_SICRL SICRL_LDP_A - -#define CONFIG_SYS_GPIO1_PRELIM -#define CONFIG_SYS_GPIO1_DIR 0x00100000 -#define CONFIG_SYS_GPIO1_DAT 0x00100000 - -#define CONFIG_SYS_GPIO2_PRELIM -#define CONFIG_SYS_GPIO2_DIR 0x78900000 -#define CONFIG_SYS_GPIO2_DAT 0x70100000 - -#ifdef CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE -#endif - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ -#endif - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE - -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#endif - -#define CONFIG_HOSTNAME "VME8349" -#define CONFIG_ROOTPATH "/tftpboot/rootfs" -#define CONFIG_BOOTFILE "uImage" - -#define CONFIG_LOADADDR 800000 /* def location for tftp and bootm */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=vme8349\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0" \ - "update=protect off fff00000 fff3ffff; " \ - "era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \ - "upd=run load update\0" \ - "fdtaddr=780000\0" \ - "fdtfile=vme8349.dtb\0" \ - "" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ - "$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND "run flash_self" - -#ifndef __ASSEMBLY__ -int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen, - unsigned char *buffer, int len); -#endif - -#endif /* __CONFIG_H */ |