diff options
Diffstat (limited to 'include/configs/cm_t35.h')
| -rw-r--r-- | include/configs/cm_t35.h | 254 |
1 files changed, 0 insertions, 254 deletions
diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h deleted file mode 100644 index f9a6444..0000000 --- a/include/configs/cm_t35.h +++ /dev/null @@ -1,254 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2011 CompuLab, Ltd. - * Mike Rapoport <mike@compulab.co.il> - * Igor Grinberg <grinberg@compulab.co.il> - * - * Based on omap3_beagle.h - * (C) Copyright 2006-2008 - * Texas Instruments. - * Richard Woodruff <r-woodruff2@ti.com> - * Syed Mohammed Khasim <x0khasim@ti.com> - * - * Configuration settings for the CompuLab CM-T35 and CM-T3730 boards - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_SYS_CACHELINE_SIZE 64 - -/* - * High Level Configuration Options - */ -#define CONFIG_CM_T3X /* working with CM-T35 and CM-T3730 */ - -#include <asm/arch/cpu.h> /* get chip and board defs */ -#include <asm/arch/omap.h> - -/* Clock Defines */ -#define V_OSCK 26000000 /* Clock output from T2 */ -#define V_SCLK (V_OSCK >> 1) - -#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG -#define CONFIG_REVISION_TAG -#define CONFIG_SERIAL_TAG - -/* - * Size of malloc() pool - */ - /* Sector */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) - -/* - * Hardware drivers - */ - -/* - * NS16550 Configuration - */ -#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ - -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK - -/* - * select serial console configuration - */ -#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE -#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ - 115200} - -/* USB device configuration */ -#define CONFIG_USB_DEVICE -#define CONFIG_USB_TTY - -/* commands to include */ - -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_I2C_EEPROM_BUS 0 -#define CONFIG_I2C_MULTI_BUS - -/* - * TWL4030 - */ - -/* - * Board NAND Info. - */ -#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ - /* to access nand at */ - /* CS0 */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ - /* devices */ - -/* Environment information */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - "loadaddr=0x82000000\0" \ - "usbtty=cdc_acm\0" \ - "console=ttyO2,115200n8\0" \ - "mpurate=500\0" \ - "vram=12M\0" \ - "dvimode=1024x768MR-16@60\0" \ - "defaultdisplay=dvi\0" \ - "mmcdev=0\0" \ - "mmcroot=/dev/mmcblk0p2 rw\0" \ - "mmcrootfstype=ext4 rootwait\0" \ - "nandroot=/dev/mtdblock4 rw\0" \ - "nandrootfstype=ubifs\0" \ - "mmcargs=setenv bootargs console=${console} " \ - "mpurate=${mpurate} " \ - "vram=${vram} " \ - "omapfb.mode=dvi:${dvimode} " \ - "omapdss.def_disp=${defaultdisplay} " \ - "root=${mmcroot} " \ - "rootfstype=${mmcrootfstype}\0" \ - "nandargs=setenv bootargs console=${console} " \ - "mpurate=${mpurate} " \ - "vram=${vram} " \ - "omapfb.mode=dvi:${dvimode} " \ - "omapdss.def_disp=${defaultdisplay} " \ - "root=${nandroot} " \ - "rootfstype=${nandrootfstype}\0" \ - "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ - "bootscript=echo Running bootscript from mmc ...; " \ - "source ${loadaddr}\0" \ - "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ - "mmcboot=echo Booting from mmc ...; " \ - "run mmcargs; " \ - "bootm ${loadaddr}\0" \ - "nandboot=echo Booting from nand ...; " \ - "run nandargs; " \ - "nand read ${loadaddr} 2a0000 400000; " \ - "bootm ${loadaddr}\0" \ - -#define CONFIG_BOOTCOMMAND \ - "mmc dev ${mmcdev}; if mmc rescan; then " \ - "if run loadbootscript; then " \ - "run bootscript; " \ - "else " \ - "if run loaduimage; then " \ - "run mmcboot; " \ - "else run nandboot; " \ - "fi; " \ - "fi; " \ - "else run nandboot; fi" - -/* - * Miscellaneous configurable options - */ -#define CONFIG_TIMESTAMP -#define CONFIG_SYS_AUTOLOAD "no" - -#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) /* memtest */ - /* works on */ -#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ - 0x01F00000) /* 31MB */ - -#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */ - /* load address */ - -/* - * OMAP3 has 12 GP timers, they can be driven by the system clock - * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). - * This rate is divided by a local divisor. - */ -#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) -#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ - -/*----------------------------------------------------------------------- - * Physical Memory Map - */ -#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ - -/* **** PISMO SUPPORT *** */ -/* Monitor at start of flash */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ - -#define CONFIG_ENV_ADDR 0x260000 - -/* additions for new relocation code, must be added to all boards */ -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 -#define CONFIG_SYS_INIT_RAM_SIZE 0x800 -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* Status LED */ -#define GREEN_LED_GPIO 186 /* CM-T35 Green LED is GPIO186 */ - -#define CONFIG_SPLASHIMAGE_GUARD - -/* Display Configuration */ -#define LCD_BPP LCD_COLOR16 - -#define CONFIG_SPLASH_SCREEN -#define CONFIG_SPLASH_SOURCE -#define CONFIG_BMP_16BPP -#define CONFIG_SCF0403_LCD - -/* Defines for SPL */ - -#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 -#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" - -#define CONFIG_SPL_NAND_BASE -#define CONFIG_SPL_NAND_DRIVERS -#define CONFIG_SPL_NAND_ECC - -/* NAND boot config */ -#define CONFIG_SYS_NAND_5_ADDR_CYCLE -#define CONFIG_SYS_NAND_PAGE_COUNT 64 -#define CONFIG_SYS_NAND_PAGE_SIZE 2048 -#define CONFIG_SYS_NAND_OOBSIZE 64 -#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) -#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS -/* - * Use the ECC/OOB layout from omap_gpmc.h that matches your chip: - * SP vs LP, 8bit vs 16bit: GPMC_NAND_HW_ECC_LAYOUT - */ -#define CONFIG_SYS_NAND_ECCPOS { 1, 2, 3, 4, 5, 6, 7, 8, 9, \ - 10, 11, 12 } -#define CONFIG_SYS_NAND_ECCSIZE 512 -#define CONFIG_SYS_NAND_ECCBYTES 3 -#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW - -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 - -#define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \ - CONFIG_SPL_TEXT_BASE) - -/* - * Use 0x80008000 as TEXT_BASE here for compatibility reasons with the - * older x-loader implementations. And move the BSS area so that it - * doesn't overlap with TEXT_BASE. - */ -#define CONFIG_SPL_BSS_START_ADDR 0x80100000 -#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ - -#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 -#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 - -/* EEPROM */ -#define CONFIG_ENV_EEPROM_IS_ON_I2C -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 -#define CONFIG_SYS_EEPROM_SIZE 256 - -#endif /* __CONFIG_H */ |