diff options
Diffstat (limited to 'include/configs/db-88f6281-bp.h')
| -rw-r--r-- | include/configs/db-88f6281-bp.h | 96 |
1 files changed, 0 insertions, 96 deletions
diff --git a/include/configs/db-88f6281-bp.h b/include/configs/db-88f6281-bp.h deleted file mode 100644 index 1b5541e..0000000 --- a/include/configs/db-88f6281-bp.h +++ /dev/null @@ -1,96 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ - -#ifndef _CONFIG_DB_88F6281_BP_H -#define _CONFIG_DB_88F6281_BP_H - -/* - * High Level Configuration Options (easy to change) - */ -#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ -#define CONFIG_KW88F6281 1 /* SOC Name */ -#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_SYS_TCLK 166666667 -#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg -#define CONFIG_BUILD_TARGET "u-boot.kwb" - -/* additions for new ARM relocation support */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ -#define CONFIG_KIRKWOOD_GPIO 1 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /* Console on UART0 */ - -/* - * Environment variables configurations - */ -#define CONFIG_ENV_SPI_BUS 0 -#define CONFIG_ENV_SPI_CS 0 -#define CONFIG_ENV_SPI_MAX_HZ 20000000 /* 20Mhz */ -#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE -#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K */ -#define CONFIG_ENV_SIZE 0x01000 -#define CONFIG_ENV_OFFSET 0xC0000 - -/* - * U-Boot bootcode configuration - */ - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */ -#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/ - -/* size in bytes reserved for initial data */ - -#include <asm/arch/config.h> -/* There is no PHY directly connected so don't ask it for link status */ -#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN - -/* - * Other required minimal configurations - */ -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ -#define CONFIG_SYS_MEMTEST_END 0x007fffff /* (_8M - 1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ - -/* - * SDIO/MMC Card Configuration - */ -#ifdef CONFIG_CMD_MMC -#define CONFIG_MVEBU_MMC -#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE -#endif /* CONFIG_CMD_MMC */ - -/* - * SATA Driver configuration - */ -#ifdef CONFIG_MVSATA_IDE -#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET -#endif /*CONFIG_MVSATA_IDE*/ - -#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */ - -#endif /* _CONFIG_DB_88F6281_BP_H */ |