diff options
Diffstat (limited to 'include/configs/ge_bx50v3.h')
| -rw-r--r-- | include/configs/ge_bx50v3.h | 237 |
1 files changed, 0 insertions, 237 deletions
diff --git a/include/configs/ge_bx50v3.h b/include/configs/ge_bx50v3.h deleted file mode 100644 index 6de5119..0000000 --- a/include/configs/ge_bx50v3.h +++ /dev/null @@ -1,237 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2015 Timesys Corporation - * Copyright (C) 2015 General Electric Company - * Copyright (C) 2014 Advantech - * Copyright (C) 2012 Freescale Semiconductor, Inc. - * - * Configuration settings for the GE MX6Q Bx50v3 boards. - */ - -#ifndef __GE_BX50V3_CONFIG_H -#define __GE_BX50V3_CONFIG_H - -#include <asm/arch/imx-regs.h> -#include <asm/mach-imx/gpio.h> - -#define CONFIG_BOARD_NAME "General Electric Bx50v3" - -#define CONFIG_MXC_UART_BASE UART3_BASE -#define CONSOLE_DEV "ttymxc2" - -#include "mx6_common.h" -#include <linux/sizes.h> - -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG -#define CONFIG_REVISION_TAG -#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M) - -#define CONFIG_MXC_UART - -/* SATA Configs */ -#ifdef CONFIG_CMD_SATA -#define CONFIG_SYS_SATA_MAX_DEVICE 1 -#define CONFIG_DWC_AHSATA_PORT_ID 0 -#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR -#define CONFIG_LBA48 -#endif - -/* USB Configs */ -#ifdef CONFIG_USB -#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET -#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) -#define CONFIG_MXC_USB_FLAGS 0 - -#define CONFIG_USBD_HS -#define CONFIG_USB_GADGET_MASS_STORAGE -#endif - -/* Networking Configs */ -#ifdef CONFIG_NET -#define CONFIG_FEC_MXC -#define IMX_FEC_BASE ENET_BASE_ADDR -#define CONFIG_FEC_XCV_TYPE RGMII -#define CONFIG_ETHPRIME "FEC" -#define CONFIG_FEC_MXC_PHYADDR 4 -#define CONFIG_PHY_ATHEROS -#endif - -/* Serial Flash */ - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_LOADADDR 0x12000000 - -#ifdef CONFIG_NFS_CMD -#define NETWORKBOOT \ - "setnetworkboot=" \ - "setenv ipaddr 172.16.2.10; setenv serverip 172.16.2.20; " \ - "setenv gatewayip 172.16.2.20; setenv nfsserver 172.16.2.20; " \ - "setenv netmask 255.255.255.0; setenv ethaddr ca:fe:de:ca:f0:11; " \ - "setenv bootargs root=/dev/nfs nfsroot=${nfsserver}:/srv/nfs/,v3,tcp rw rootwait" \ - "setenv bootargs $bootargs ip=${ipaddr}:${nfsserver}:${gatewayip}:${netmask}::eth0:off " \ - "setenv bootargs $bootargs cma=128M bootcause=POR console=${console} ${videoargs} " \ - "setenv bootargs $bootargs systemd.mask=helix-network-defaults.service " \ - "setenv bootargs $bootargs watchdog.handle_boot_enabled=1\0" \ - "networkboot=" \ - "run setnetworkboot; " \ - "nfs ${loadaddr} /srv/nfs/fitImage; " \ - "bootm ${loadaddr}#conf@${confidx}\0" \ - -#define CONFIG_NETWORKBOOTCOMMAND \ - "run networkboot; " \ - -#else -#define NETWORKBOOT \ - -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - NETWORKBOOT \ - "bootcause=POR\0" \ - "image=/boot/fitImage\0" \ - "fdt_high=0xffffffff\0" \ - "dev=mmc\0" \ - "devnum=2\0" \ - "rootdev=mmcblk0p\0" \ - "quiet=quiet loglevel=0\0" \ - "console=" CONSOLE_DEV "\0" \ - "setargs=setenv bootargs root=/dev/${rootdev}${partnum} " \ - "ro rootwait cma=128M " \ - "bootcause=${bootcause} " \ - "${quiet} console=${console} ${rtc_status} " \ - "${videoargs}" "\0" \ - "doquiet=" \ - "if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; " \ - "then setenv quiet; fi\0" \ - "hasfirstboot=" \ - "ext2load ${dev} ${devnum}:${partnum} 0x7000A000 " \ - "/boot/bootcause/firstboot\0" \ - "swappartitions=" \ - "setexpr partnum 3 - ${partnum}\0" \ - "failbootcmd=" \ - "bx50_backlight_enable; " \ - "msg=\"Monitor failed to start. Try again, or contact GE Service for support.\"; " \ - "echo $msg; " \ - "setenv stdout vga; " \ - "echo \"\n\n\n\n \" $msg; " \ - "setenv stdout serial; " \ - "mw.b 0x7000A000 0xbc; " \ - "mw.b 0x7000A001 0x00; " \ - "ext4write ${dev} ${devnum}:5 0x7000A000 /boot/failures 2\0" \ - "altbootcmd=" \ - "run doquiet; " \ - "setenv partnum 1; run hasfirstboot || setenv partnum 2; " \ - "run hasfirstboot || setenv partnum 0; " \ - "if test ${partnum} != 0; then " \ - "setenv bootcause REVERT; " \ - "run swappartitions loadimage doboot; " \ - "fi; " \ - "run failbootcmd\0" \ - "loadimage=" \ - "ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \ - "doboot=" \ - "echo Booting from ${dev}:${devnum}:${partnum} ...; " \ - "run setargs; " \ - "bootm ${loadaddr}#conf@${confidx}\0" \ - "tryboot=" \ - "setenv partnum 1; run hasfirstboot || setenv partnum 2; " \ - "run loadimage || run swappartitions && run loadimage || " \ - "setenv partnum 0 && echo MISSING IMAGE;" \ - "run doboot; " \ - "run failbootcmd\0" \ - -#define CONFIG_MMCBOOTCOMMAND \ - "if mmc dev ${devnum}; then " \ - "run doquiet; " \ - "run tryboot; " \ - "fi; " \ - -#define CONFIG_USBBOOTCOMMAND \ - "echo Unsupported; " \ - -#ifdef CONFIG_NFS_CMD -#define CONFIG_BOOTCOMMAND CONFIG_NETWORKBOOTCOMMAND -#elif CONFIG_CMD_USB -#define CONFIG_BOOTCOMMAND CONFIG_USBBOOTCOMMAND -#else -#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND -#endif - - -/* Miscellaneous configurable options */ - -#define CONFIG_SYS_MEMTEST_START 0x10000000 -#define CONFIG_SYS_MEMTEST_END 0x10010000 -#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000 - -#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR - -/* Physical Memory Map */ -#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM -#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR -#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) - -/* environment organization */ -#define CONFIG_ENV_SIZE (8 * 1024) -#define CONFIG_ENV_OFFSET (768 * 1024) -#define CONFIG_ENV_SECT_SIZE (64 * 1024) - -#define CONFIG_SYS_FSL_USDHC_NUM 3 - -/* Framebuffer */ -#define CONFIG_HIDE_LOGO_VERSION -#define CONFIG_IMX_HDMI -#define CONFIG_IMX_VIDEO_SKIP -#define CONFIG_CMD_BMP - -#define CONFIG_IMX6_PWM_PER_CLK 66000000 - -#define CONFIG_PCI -#define CONFIG_PCI_PNP -#define CONFIG_PCI_SCAN_SHOW -#define CONFIG_PCIE_IMX -#define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12) -#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(1, 5) - -#define CONFIG_RTC_RX8010SJ -#define CONFIG_SYS_RTC_BUS_NUM 2 -#define CONFIG_SYS_I2C_RTC_ADDR 0x32 - -/* I2C Configs */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_MXC_I2C1 -#define CONFIG_SYS_I2C_MXC_I2C2 -#define CONFIG_SYS_I2C_MXC_I2C3 - -#define CONFIG_SYS_NUM_I2C_BUSES 11 -#define CONFIG_SYS_I2C_MAX_HOPS 1 -#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ - {1, {I2C_NULL_HOP} }, \ - {2, {I2C_NULL_HOP} }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 0} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 6} } }, \ - {0, {{I2C_MUX_PCA9547, 0x70, 7} } }, \ - } - -#define CONFIG_BCH - -#endif /* __GE_BX50V3_CONFIG_H */ |