diff options
Diffstat (limited to 'include/configs/ids8313.h')
| -rw-r--r-- | include/configs/ids8313.h | 306 |
1 files changed, 0 insertions, 306 deletions
diff --git a/include/configs/ids8313.h b/include/configs/ids8313.h deleted file mode 100644 index 43cb14c..0000000 --- a/include/configs/ids8313.h +++ /dev/null @@ -1,306 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2013 - * Heiko Schocher, DENX Software Engineering, hs@denx.de. - * - * Based on: - * Copyright (c) 2011 IDS GmbH, Germany - * Sergej Stepanov <ste@ids.de> - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_FSL_ELBC - -#define CONFIG_BOOT_RETRY_TIME 900 -#define CONFIG_BOOT_RETRY_MIN 30 -#define CONFIG_RESET_TO_RETRY - -#define CONFIG_SYS_SICRH 0x00000000 -#define CONFIG_SYS_SICRL (SICRL_LBC | SICRL_SPI_D) - -#define CONFIG_HWCONFIG - -/* - * Definitions for initial stack pointer and data area (in DCACHE ) - */ -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_SIZE 0x100 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \ - - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* - * Internal Definitions - */ -/* - * DDR Setup - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -/* - * Manually set up DDR parameters, - * as this board has not the SPD connected to I2C. - */ -#define CONFIG_SYS_DDR_SIZE 256 /* MB */ -#define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN |\ - 0x00010000 |\ - CSCONFIG_ROW_BIT_13 |\ - CSCONFIG_COL_BIT_10) - -#define CONFIG_SYS_DDR_CONFIG_256 (CONFIG_SYS_DDR_CONFIG | \ - CSCONFIG_BANK_BIT_3) - -#define CONFIG_SYS_DDR_TIMING_3 (1 << 16) /* ext refrec */ -#define CONFIG_SYS_DDR_TIMING_0 ((3 << TIMING_CFG0_RWT_SHIFT) |\ - (3 << TIMING_CFG0_WRT_SHIFT) |\ - (3 << TIMING_CFG0_RRT_SHIFT) |\ - (3 << TIMING_CFG0_WWT_SHIFT) |\ - (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\ - (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\ - (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ - (2 << TIMING_CFG0_MRS_CYC_SHIFT)) -#define CONFIG_SYS_DDR_TIMING_1 ((4 << TIMING_CFG1_PRETOACT_SHIFT) |\ - (12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\ - (4 << TIMING_CFG1_ACTTORW_SHIFT) |\ - (7 << TIMING_CFG1_CASLAT_SHIFT) |\ - (4 << TIMING_CFG1_REFREC_SHIFT) |\ - (4 << TIMING_CFG1_WRREC_SHIFT) |\ - (2 << TIMING_CFG1_ACTTOACT_SHIFT) |\ - (2 << TIMING_CFG1_WRTORD_SHIFT)) -#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\ - (5 << TIMING_CFG2_CPO_SHIFT) |\ - (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\ - (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\ - (0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\ - (1 << TIMING_CFG2_CKE_PLS_SHIFT) |\ - (6 << TIMING_CFG2_FOUR_ACT_SHIFT)) - -#define CONFIG_SYS_DDR_INTERVAL ((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\ - (0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) - -#define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN |\ - SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\ - SDRAM_CFG_DBW_32 |\ - SDRAM_CFG_SDRAM_TYPE_DDR2) - -#define CONFIG_SYS_SDRAM_CFG2 0x00401000 -#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) |\ - (0x0242 << SDRAM_MODE_SD_SHIFT)) -#define CONFIG_SYS_DDR_MODE_2 0x00000000 -#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075 -#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN |\ - DDRCDR_PZ_NOMZ |\ - DDRCDR_NZ_NOMZ |\ - DDRCDR_ODT |\ - DDRCDR_M_ODR |\ - DDRCDR_Q_DRN) - -/* - * on-board devices - */ -#define CONFIG_TSEC1 -#define CONFIG_TSEC2 - -/* - * NOR FLASH setup - */ -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT -#define CONFIG_FLASH_SHOW_PROGRESS 50 - -#define CONFIG_SYS_FLASH_BASE 0xFF800000 -#define CONFIG_SYS_FLASH_SIZE 8 - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 128 - -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 - -/* - * NAND FLASH setup - */ -#define CONFIG_SYS_NAND_BASE 0xE1000000 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_MAX_CHIPS 1 -#define CONFIG_NAND_FSL_ELBC -#define CONFIG_SYS_NAND_PAGE_SIZE (2048) -#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) -#define NAND_CACHE_PAGES 64 - - -/* - * MRAM setup - */ -#define CONFIG_SYS_MRAM_BASE 0xE2000000 -#define CONFIG_SYS_MRAM_SIZE 0x20000 /* 128 Kb */ - -#define CONFIG_SYS_OR_TIMING_MRAM - - -/* - * CPLD setup - */ -#define CONFIG_SYS_CPLD_BASE 0xE3000000 -#define CONFIG_SYS_CPLD_SIZE 0x8000 - -#define CONFIG_SYS_OR_TIMING_MRAM - - -/* - * HW-Watchdog - */ -#define CONFIG_WATCHDOG 1 -#define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF - -/* - * I2C setup - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 -#define CONFIG_RTC_PCF8563 -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 - -/* - * Ethernet setup - */ -#ifdef CONFIG_TSEC1 -#define CONFIG_HAS_ETH0 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_SYS_TSEC1_OFFSET 0x24000 -#define TSEC1_PHY_ADDR 0x1 -#define TSEC1_FLAGS TSEC_GIGABIT -#define TSEC1_PHYIDX 0 -#endif - -#ifdef CONFIG_TSEC2 -#define CONFIG_HAS_ETH1 -#define CONFIG_TSEC2_NAME "TSEC1" -#define CONFIG_SYS_TSEC2_OFFSET 0x25000 -#define TSEC2_PHY_ADDR 0x3 -#define TSEC2_FLAGS TSEC_GIGABIT -#define TSEC2_PHYIDX 0 -#endif -#define CONFIG_ETHPRIME "TSEC1" - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) -#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)) - -#define CONFIG_HAS_FSL_DR_USB -#define CONFIG_SYS_SCCR_USBDRCM 3 - -/* - * U-Boot environment setup - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) -#define CONFIG_SYS_MALLOC_LEN (8 * 1024 * 1024) - -/* - * Environment Configuration - */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \ - + CONFIG_SYS_MONITOR_LEN) -#define CONFIG_ENV_SIZE 0x20000 -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#define CONFIG_NETDEV eth1 -#define CONFIG_HOSTNAME "ids8313" -#define CONFIG_ROOTPATH "/opt/eldk-4.2/ppc_6xx" -#define CONFIG_BOOTFILE "ids8313/uImage" -#define CONFIG_UBOOTPATH "ids8313/u-boot.bin" -#define CONFIG_FDTFILE "ids8313/ids8313.dtb" -#define CONFIG_LOADADDR 0x400000 -#define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo" - -/* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_CBSIZE 1024 -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x00001000 -#define CONFIG_SYS_MEMTEST_END 0x00C00000 - -#define CONFIG_SYS_LOAD_ADDR 0x100000 -#define CONFIG_LOADS_ECHO -#define CONFIG_TIMESTAMP -#define CONFIG_BOOTCOMMAND "run boot_cramfs" -#undef CONFIG_SYS_LOADS_BAUD_CHANGE - -#define CONFIG_JFFS2_NAND -#define CONFIG_JFFS2_DEV "0" - -/* mtdparts command line support */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=" __stringify(CONFIG_NETDEV) "\0" \ - "ethprime=TSEC1\0" \ - "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ - "tftpflash=tftpboot ${loadaddr} ${uboot}; " \ - "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +${filesize}; " \ - "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +${filesize}; " \ - "cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \ - " ${filesize}; " \ - "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +${filesize}; " \ - "cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \ - " ${filesize}\0" \ - "console=ttyS0\0" \ - "fdtaddr=0x780000\0" \ - "kernel_addr=ff800000\0" \ - "fdtfile=" __stringify(CONFIG_FDTFILE) "\0" \ - "setbootargs=setenv bootargs " \ - "root=${rootdev} rw console=${console}," \ - "${baudrate} ${othbootargs}\0" \ - "setipargs=setenv bootargs root=${rootdev} rw " \ - "nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:" \ - "${netmask}:${hostname}:${netdev}:off " \ - "console=${console},${baudrate} ${othbootargs}\0" \ - "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ - "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \ - "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \ - "\0" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv rootdev /dev/nfs;" \ - "run setipargs;run addmtd;" \ - "tftp ${loadaddr} ${bootfile};" \ - "tftp ${fdtaddr} ${fdtfile};" \ - "fdt addr ${fdtaddr};" \ - "bootm ${loadaddr} - ${fdtaddr}" - -/* UBI Support */ - -#endif /* __CONFIG_H */ |