1 files changed, 0 insertions, 110 deletions
diff --git a/include/configs/lx2160ardb.h b/include/configs/lx2160ardb.h
deleted file mode 100644
index c6bacb6..0000000
--- a/include/configs/lx2160ardb.h
+++ /dev/null
@@ -1,110 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2018 NXP
- */
-
-#ifndef __LX2_RDB_H
-#define __LX2_RDB_H
-
-#include "lx2160a_common.h"
-
-/* Qixis */
-#define QIXIS_XMAP_MASK			0x07
-#define QIXIS_XMAP_SHIFT		5
-#define QIXIS_RST_CTL_RESET_EN		0x30
-#define QIXIS_LBMAP_DFLTBANK		0x00
-#define QIXIS_LBMAP_ALTBANK		0x20
-#define QIXIS_LBMAP_QSPI		0x00
-#define QIXIS_RCW_SRC_QSPI		0xff
-#define QIXIS_RST_CTL_RESET		0x31
-#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
-#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
-#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
-#define QIXIS_LBMAP_MASK		0x0f
-#define QIXIS_LBMAP_SD
-#define QIXIS_RCW_SRC_SD           0x08
-#define NON_EXTENDED_DUTCFG
-
-/* VID */
-
-#define I2C_MUX_CH_VOL_MONITOR		0xA
-/* Voltage monitor on channel 2*/
-#define I2C_VOL_MONITOR_ADDR		0x63
-#define I2C_VOL_MONITOR_BUS_V_OFFSET	0x2
-#define I2C_VOL_MONITOR_BUS_V_OVF	0x1
-#define I2C_VOL_MONITOR_BUS_V_SHIFT	3
-#define CONFIG_VID_FLS_ENV		"lx2160ardb_vdd_mv"
-#define CONFIG_VID
-
-/* The lowest and highest voltage allowed*/
-#define VDD_MV_MIN			775
-#define VDD_MV_MAX			855
-
-/* PM Bus commands code for LTC3882*/
-#define PMBUS_CMD_PAGE                  0x0
-#define PMBUS_CMD_READ_VOUT             0x8B
-#define PMBUS_CMD_PAGE_PLUS_WRITE       0x05
-#define PMBUS_CMD_VOUT_COMMAND          0x21
-#define PWM_CHANNEL0                    0x0
-
-#define CONFIG_VOL_MONITOR_LTC3882_SET
-#define CONFIG_VOL_MONITOR_LTC3882_READ
-
-/* RTC */
-#define CONFIG_SYS_RTC_BUS_NUM		4
-
-/* MAC/PHY configuration */
-#if defined(CONFIG_FSL_MC_ENET)
-#define CONFIG_MII
-#define CONFIG_ETHPRIME		"DPMAC1@xgmii"
-
-#define AQR107_PHY_ADDR1	0x04
-#define AQR107_PHY_ADDR2	0x05
-#define AQR107_IRQ_MASK		0x0C
-
-#define CORTINA_NO_FW_UPLOAD
-#define CORTINA_PHY_ADDR1	0x0
-#define INPHI_PHY_ADDR1		0x0
-
-#define RGMII_PHY_ADDR1		0x01
-#define RGMII_PHY_ADDR2		0x02
-
-#endif
-
-/* EMC2305 */
-#define I2C_MUX_CH_EMC2305		0x09
-#define I2C_EMC2305_ADDR		0x4D
-#define I2C_EMC2305_CMD		0x40
-#define I2C_EMC2305_PWM		0x80
-
-/* EEPROM */
-#define CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#define CONFIG_SYS_EEPROM_BUS_NUM	           0
-#define CONFIG_SYS_I2C_EEPROM_ADDR	           0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	    1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS     3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
-
-/* Initial environment variables */
-#define CONFIG_EXTRA_ENV_SETTINGS		\
-	EXTRA_ENV_SETTINGS			\
-	"lx2160ardb_vdd_mv=800\0"		\
-	"BOARD=lx2160ardb\0"			\
-	"xspi_bootcmd=echo Trying load from flexspi..;"		\
-		"sf probe 0:0 && sf read $load_addr "		\
-		"$kernel_start $kernel_size ; env exists secureboot &&"	\
-		"sf read $kernelheader_addr_r $kernelheader_start "	\
-		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
-		" bootm $load_addr#$BOARD\0"			\
-	"sd_bootcmd=echo Trying load from sd card..;"		\
-		"mmcinfo; mmc read $load_addr "			\
-		"$kernel_addr_sd $kernel_size_sd ;"		\
-		"env exists secureboot && mmc read $kernelheader_addr_r "\
-		"$kernelhdr_addr_sd $kernelhdr_size_sd "	\
-		" && esbc_validate ${kernelheader_addr_r};"	\
-		"bootm $load_addr#$BOARD\0"
-
-#include <asm/fsl_secure_boot.h>
-
-#endif /* __LX2_RDB_H */