diff options
Diffstat (limited to 'include/configs/sbc8349.h')
| -rw-r--r-- | include/configs/sbc8349.h | 341 |
1 files changed, 0 insertions, 341 deletions
diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h deleted file mode 100644 index d2053cc..0000000 --- a/include/configs/sbc8349.h +++ /dev/null @@ -1,341 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * WindRiver SBC8349 U-Boot configuration file. - * Copyright (c) 2006, 2007 Wind River Systems, Inc. - * - * Paul Gortmaker <paul.gortmaker@windriver.com> - * Based on the MPC8349EMDS config. - */ - -/* - * sbc8349 board configuration file. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 Family */ - -/* Don't enable PCI2 on sbc834x - it doesn't exist physically. */ -#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */ - -#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x00100000 - -/* - * DDR Setup - */ -#undef CONFIG_DDR_ECC /* only for ECC DDR module */ -#undef CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */ -#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/ -#define CONFIG_SYS_83XX_DDR_USES_CS0 /* WRS; Fsl board uses CS2/CS3 */ - -/* - * 32-bit data path mode. - * - * Please note that using this mode for devices with the real density of 64-bit - * effectively reduces the amount of available memory due to the effect of - * wrapping around while translating address to row/columns, for example in the - * 256MB module the upper 128MB get aliased with contents of the lower - * 128MB); normally this define should be used for devices with real 32-bit - * data path. - */ -#undef CONFIG_DDR_32BIT - -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ - DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075) -#define CONFIG_DDR_2T_TIMING - -#if defined(CONFIG_SPD_EEPROM) -/* - * Determine DDR configuration from I2C interface. - */ -#define SPD_EEPROM_ADDRESS 0x52 /* DDR DIMM */ - -#else -/* - * Manually set up DDR parameters - * NB: manual DDR setup untested on sbc834x - */ -#define CONFIG_SYS_DDR_SIZE 256 /* MB */ -#define CONFIG_SYS_DDR_CS2_CONFIG (CSCONFIG_EN \ - | CSCONFIG_ROW_BIT_13 \ - | CSCONFIG_COL_BIT_10) -#define CONFIG_SYS_DDR_TIMING_1 0x36332321 -#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ -#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ -#define CONFIG_SYS_DDR_INTERVAL 0x04060100 /* autocharge,no open page */ - -#if defined(CONFIG_DDR_32BIT) -/* set burst length to 8 for 32-bit data path */ - /* DLL,normal,seq,4/2.5, 8 burst len */ -#define CONFIG_SYS_DDR_MODE 0x00000023 -#else -/* the default burst length is 4 - for 64-bit data path */ - /* DLL,normal,seq,4/2.5, 4 burst len */ -#define CONFIG_SYS_DDR_MODE 0x00000022 -#endif -#endif - -/* - * SDRAM on the Local Bus - */ -#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* Localbus SDRAM */ -#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ - -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* start of FLASH */ -#define CONFIG_SYS_FLASH_SIZE 8 /* flash size in MB */ - - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */ - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_INIT_RAM_LOCK 1 - /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 - /* Size of used area in RAM*/ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 - -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */ - -#undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */ - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69}, {1, 0x69} } -/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */ - -/* TSEC */ -#define CONFIG_SYS_TSEC1_OFFSET 0x24000 -#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) -#define CONFIG_SYS_TSEC2_OFFSET 0x25000 -#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE -#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 -#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE -#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ - -#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000 -#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE -#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000 -#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE -#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI2_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000 -#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */ - -#if defined(CONFIG_PCI) - -#undef CONFIG_EEPRO100 -#undef CONFIG_TULIP - -#if !defined(CONFIG_PCI_PNP) - #define PCI_ENET0_IOADDR 0xFIXME - #define PCI_ENET0_MEMADDR 0xFIXME - #define PCI_IDSEL_NUMBER 0xFIXME -#endif - -#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ - -#endif /* CONFIG_PCI */ - -/* - * TSEC configuration - */ - -#if defined(CONFIG_TSEC_ENET) - -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "TSEC1" -#define CONFIG_PHY_BCM5421S 1 -#define TSEC1_PHY_ADDR 0x19 -#define TSEC2_PHY_ADDR 0x1a -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC1_FLAGS TSEC_GIGABIT -#define TSEC2_FLAGS TSEC_GIGABIT - -/* Options are: TSEC[0-1] */ -#define CONFIG_ETHPRIME "TSEC0" - -#endif /* CONFIG_TSEC_ENET */ - -/* - * Environment - */ -#ifndef CONFIG_SYS_RAMBOOT - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) - #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ - #define CONFIG_ENV_SIZE 0x2000 - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#else - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) - #define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * Command line configuration. - */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ - /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) - -#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ - -/* System IO Config */ -#define CONFIG_SYS_SICRH 0 -#define CONFIG_SYS_SICRL SICRL_LDP_A - -#ifdef CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE -#endif - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ -#endif - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE - -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#endif - -#define CONFIG_HOSTNAME "SBC8349" -#define CONFIG_ROOTPATH "/tftpboot/rootfs" -#define CONFIG_BOOTFILE "uImage" - - /* default location for tftp and bootm */ -#define CONFIG_LOADADDR 800000 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=sbc8349\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "load=tftp 100000 /tftpboot/sbc8349/u-boot.bin\0" \ - "update=protect off ff800000 ff83ffff; " \ - "era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \ - "upd=run load update\0" \ - "fdtaddr=780000\0" \ - "fdtfile=sbc8349.dtb\0" \ - "" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ - "$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND "run flash_self" - -#endif /* __CONFIG_H */ |