diff options
Diffstat (limited to 'include/configs/smartweb.h')
| -rw-r--r-- | include/configs/smartweb.h | 220 |
1 files changed, 0 insertions, 220 deletions
diff --git a/include/configs/smartweb.h b/include/configs/smartweb.h deleted file mode 100644 index c1a43a5..0000000 --- a/include/configs/smartweb.h +++ /dev/null @@ -1,220 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2007-2008 - * Stelian Pop <stelian@popies.net> - * Lead Tech Design <www.leadtechdesign.com> - * - * (C) Copyright 2010 - * Achim Ehrlich <aehrlich@taskit.de> - * taskit GmbH <www.taskit.de> - * - * (C) Copyright 2012 - * Markus Hubig <mhubig@imko.de> - * IMKO GmbH <www.imko.de> - * - * (C) Copyright 2014 - * Heiko Schocher <hs@denx.de> - * DENX Software Engineering GmbH - * - * Configuation settings for the smartweb. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * SoC must be defined first, before hardware.h is included. - * In this case SoC is defined in boards.cfg. - */ -#include <asm/hardware.h> -#include <linux/sizes.h> - -/* - * Warning: changing CONFIG_SYS_TEXT_BASE requires adapting the initial boot - * program. Since the linker has to swallow that define, we must use a pure - * hex number here! - */ - -/* ARM asynchronous clock */ -#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ -#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* 18.432MHz crystal */ - -/* misc settings */ -#define CONFIG_CMDLINE_TAG /* pass commandline to Kernel */ -#define CONFIG_SETUP_MEMORY_TAGS /* pass memory defs to kernel */ -#define CONFIG_INITRD_TAG /* pass initrd param to kernel */ -#define CONFIG_SKIP_LOWLEVEL_INIT_ONLY /* U-Boot is loaded by a bootloader */ - -/* We set the max number of command args high to avoid HUSH bugs. */ -#define CONFIG_SYS_MAXARGS 32 - -/* setting board specific options */ -#define CONFIG_MACH_TYPE MACH_TYPE_SMARTWEB -#define CONFIG_ENV_OVERWRITE 1 /* Overwrite ethaddr / serial# */ -#define CONFIG_SYS_AUTOLOAD "yes" -#define CONFIG_RESET_TO_RETRY - -/* The LED PINs */ -#define CONFIG_RED_LED AT91_PIN_PA9 -#define CONFIG_GREEN_LED AT91_PIN_PA6 - -/* - * SDRAM: 1 bank, 64 MB, base address 0x20000000 - * Already initialized before u-boot gets started. - */ -#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 -#define CONFIG_SYS_SDRAM_SIZE (64 * SZ_1M) - -/* - * Perform a SDRAM Memtest from the start of SDRAM - * till the beginning of the U-Boot position in RAM. - */ -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_TEXT_BASE - 0x100000) - -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN \ - ROUND(3 * CONFIG_ENV_SIZE + (4 * SZ_1M), 0x1000) - -/* NAND flash settings */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 -#define CONFIG_SYS_NAND_DBW_8 -#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) -#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) -#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 -#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 - -/* general purpose I/O */ -#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */ -#define CONFIG_AT91_GPIO /* enable the GPIO features */ -#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */ - -/* serial console */ -#define CONFIG_ATMEL_USART -#define CONFIG_USART_BASE ATMEL_BASE_DBGU -#define CONFIG_USART_ID ATMEL_ID_SYS - -/* - * Ethernet configuration - * - */ -#define CONFIG_MACB -#define CONFIG_RMII /* use reduced MII inteface */ -#define CONFIG_NET_RETRY_COUNT 20 /* # of DHCP/BOOTP retries */ -#define CONFIG_AT91_WANTS_COMMON_PHY - -/* BOOTP and DHCP options */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_NFSBOOTCOMMAND \ - "setenv autoload yes; setenv autoboot yes; " \ - "setenv bootargs ${basicargs} ${mtdparts} " \ - "root=/dev/nfs ip=dhcp nfsroot=${serverip}:/srv/nfs/rootfs; " \ - "dhcp" - -#if !defined(CONFIG_SPL_BUILD) -/* USB configuration */ -#define CONFIG_USB_ATMEL -#define CONFIG_USB_ATMEL_CLK_SEL_PLLB -#define CONFIG_USB_OHCI_NEW -#define CONFIG_SYS_USB_OHCI_CPU_INIT -#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_UHP_BASE -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260" -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 - -/* USB DFU support */ - -#define CONFIG_USB_GADGET_AT91 - -/* DFU class support */ -#define CONFIG_SYS_DFU_DATA_BUF_SIZE SZ_1M -#define DFU_MANIFEST_POLL_TIMEOUT 25000 -#endif - -/* General Boot Parameter */ -#define CONFIG_BOOTCOMMAND "run flashboot" -#define CONFIG_SYS_CBSIZE 512 - -/* - * RAM Memory address where to put the - * Linux Kernel befor starting. - */ -#define CONFIG_SYS_LOAD_ADDR 0x22000000 - -/* - * The NAND Flash partitions: - */ -#define CONFIG_ENV_OFFSET_REDUND (0x180000) -#define CONFIG_ENV_RANGE (SZ_512K) - -/* - * Predefined environment variables. - * Usefull to define some easy to use boot commands. - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - \ - "basicargs=console=ttyS0,115200\0" \ - \ - "mtdparts="CONFIG_MTDPARTS_DEFAULT"\0" - -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_INIT_SP_ADDR 0x301000 -#define CONFIG_SPL_STACK_R -#define CONFIG_SPL_STACK_R_ADDR CONFIG_SYS_TEXT_BASE -#else -/* - * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM, - * leaving the correct space for initial global data structure above that - * address while providing maximum stack area below. - */ -#define CONFIG_SYS_INIT_SP_ADDR \ - (ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE) -#endif - -/* Defines for SPL */ -#define CONFIG_SPL_MAX_SIZE (SZ_4K) - -#define CONFIG_SPL_BSS_START_ADDR CONFIG_SYS_SDRAM_BASE -#define CONFIG_SPL_BSS_MAX_SIZE (SZ_16K) -#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ - CONFIG_SPL_BSS_MAX_SIZE) -#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN - -#define CONFIG_SYS_NAND_ENABLE_PIN_SPL (2*32 + 14) -#define CONFIG_SYS_USE_NANDFLASH 1 -#define CONFIG_SPL_NAND_DRIVERS -#define CONFIG_SPL_NAND_BASE -#define CONFIG_SPL_NAND_ECC -#define CONFIG_SPL_NAND_RAW_ONLY -#define CONFIG_SPL_NAND_SOFTECC -#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x20000 -#define CONFIG_SYS_NAND_U_BOOT_SIZE SZ_512K -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_NAND_5_ADDR_CYCLE - -#define CONFIG_SYS_NAND_SIZE (SZ_256M) -#define CONFIG_SYS_NAND_PAGE_SIZE SZ_2K -#define CONFIG_SYS_NAND_BLOCK_SIZE (SZ_128K) -#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ - CONFIG_SYS_NAND_PAGE_SIZE) -#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS -#define CONFIG_SYS_NAND_ECCSIZE 256 -#define CONFIG_SYS_NAND_ECCBYTES 3 -#define CONFIG_SYS_NAND_OOBSIZE 64 -#define CONFIG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \ - 48, 49, 50, 51, 52, 53, 54, 55, \ - 56, 57, 58, 59, 60, 61, 62, 63, } - -#define CONFIG_SPL_ATMEL_SIZE -#define CONFIG_SYS_MASTER_CLOCK (198656000/2) -#define AT91_PLL_LOCK_TIMEOUT 1000000 -#define CONFIG_SYS_AT91_PLLA 0x2060bf09 -#define CONFIG_SYS_MCKR 0x100 -#define CONFIG_SYS_MCKR_CSS (0x02 | CONFIG_SYS_MCKR) -#define CONFIG_SYS_AT91_PLLB 0x10483f0e - -#define CONFIG_SPL_PAD_TO CONFIG_SYS_NAND_U_BOOT_OFFS -#define CONFIG_SYS_SPL_LEN CONFIG_SPL_PAD_TO - -#endif /* __CONFIG_H */ |