diff options
Diffstat (limited to 'include/configs/snapper9260.h')
| -rw-r--r-- | include/configs/snapper9260.h | 120 |
1 files changed, 0 insertions, 120 deletions
diff --git a/include/configs/snapper9260.h b/include/configs/snapper9260.h deleted file mode 100644 index b0408a5..0000000 --- a/include/configs/snapper9260.h +++ /dev/null @@ -1,120 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Bluewater Systems Snapper 9260 and 9G20 modules - * - * (C) Copyright 2011 Bluewater Systems - * Author: Andre Renaud <andre@bluewatersys.com> - * Author: Ryan Mallon <ryan@bluewatersys.com> - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* SoC type is defined in boards.cfg */ -#include <asm/hardware.h> -#include <linux/sizes.h> - -/* ARM asynchronous clock */ -#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* External Crystal, in Hz */ -#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 - -/* CPU */ - -#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG -#define CONFIG_SKIP_LOWLEVEL_INIT - -/* SDRAM */ -#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 -#define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) /* 64MB */ -#define CONFIG_SYS_INIT_SP_ADDR (ATMEL_BASE_SRAM1 + 0x1000 - \ - GENERATED_GBL_DATA_SIZE) - -/* Mem test settings */ -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + (1024 * 1024)) - -/* NAND Flash */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 -#define CONFIG_SYS_NAND_DBW_8 -#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* AD21 */ -#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) /* AD22 */ -#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 -#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 - -/* Ethernet */ -#define CONFIG_MACB -#define CONFIG_RMII -#define CONFIG_NET_RETRY_COUNT 20 -#define CONFIG_RESET_PHY_R -#define CONFIG_AT91_WANTS_COMMON_PHY -#define CONFIG_TFTP_PORT -#define CONFIG_TFTP_TSIZE - -/* USB */ -#define CONFIG_USB_ATMEL -#define CONFIG_USB_ATMEL_CLK_SEL_PLLB -#define CONFIG_USB_OHCI_NEW -#define CONFIG_SYS_USB_OHCI_CPU_INIT -#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_UHP_BASE -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260" -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 - -/* GPIOs and IO expander */ -#define CONFIG_ATMEL_LEGACY -#define CONFIG_AT91_GPIO -#define CONFIG_AT91_GPIO_PULLUP 1 -#define CONFIG_PCA953X -#define CONFIG_SYS_I2C_PCA953X_ADDR 0x28 -#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x28, 16} } - -/* UARTs/Serial console */ -#define CONFIG_ATMEL_USART -#ifndef CONFIG_DM_SERIAL -#define CONFIG_USART_BASE ATMEL_BASE_DBGU -#define CONFIG_USART_ID ATMEL_ID_SYS -#endif - -/* I2C - Bit-bashed */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SOFT_SPEED 100000 -#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F -#define CONFIG_SOFT_I2C_READ_REPEATED_START -#define I2C_INIT do { \ - at91_set_gpio_output(AT91_PIN_PA23, 1); \ - at91_set_gpio_output(AT91_PIN_PA24, 1); \ - at91_set_pio_multi_drive(AT91_PIO_PORTA, 23, 1); \ - at91_set_pio_multi_drive(AT91_PIO_PORTA, 24, 1); \ - } while (0) -#define I2C_SOFT_DECLARATIONS -#define I2C_ACTIVE -#define I2C_TRISTATE at91_set_gpio_input(AT91_PIN_PA23, 1); -#define I2C_READ at91_get_gpio_value(AT91_PIN_PA23); -#define I2C_SDA(bit) do { \ - if (bit) { \ - at91_set_gpio_input(AT91_PIN_PA23, 1); \ - } else { \ - at91_set_gpio_output(AT91_PIN_PA23, 1); \ - at91_set_gpio_value(AT91_PIN_PA23, bit); \ - } \ - } while (0) -#define I2C_SCL(bit) at91_set_pio_value(AT91_PIO_PORTA, 24, bit) -#define I2C_DELAY udelay(2) - -/* Boot options */ -#define CONFIG_SYS_LOAD_ADDR 0x23000000 - -#define CONFIG_BOOTP_BOOTFILESIZE - -/* Environment settings */ -#define CONFIG_ENV_OVERWRITE - -/* Console settings */ - -/* U-Boot memory settings */ -#define CONFIG_SYS_MALLOC_LEN (1 << 20) - -#endif /* __CONFIG_H */ |