diff options
Diffstat (limited to 'include/configs/vf610twr.h')
| -rw-r--r-- | include/configs/vf610twr.h | 203 |
1 files changed, 0 insertions, 203 deletions
diff --git a/include/configs/vf610twr.h b/include/configs/vf610twr.h deleted file mode 100644 index ba85bc9..0000000 --- a/include/configs/vf610twr.h +++ /dev/null @@ -1,203 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2013 Freescale Semiconductor, Inc. - * - * Configuration settings for the Freescale Vybrid vf610twr board. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#include <asm/arch/imx-regs.h> - -#define CONFIG_SYS_FSL_CLK - -#define CONFIG_MACH_TYPE 4146 - -#define CONFIG_SKIP_LOWLEVEL_INIT - -/* Enable passing of ATAGs */ -#define CONFIG_CMDLINE_TAG - -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024) - -/* Allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* NAND support */ -#define CONFIG_SYS_NAND_ONFI_DETECTION - -#ifdef CONFIG_CMD_NAND -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE NFC_BASE_ADDR - -/* Dynamic MTD partition support */ -#endif - -#define CONFIG_SYS_FSL_ESDHC_ADDR 0 -#define CONFIG_SYS_FSL_ESDHC_NUM 1 - -#define CONFIG_FEC_MXC -#define IMX_FEC_BASE ENET_BASE_ADDR -#define CONFIG_FEC_XCV_TYPE RMII -#define CONFIG_FEC_MXC_PHYADDR 0 - -/* QSPI Configs*/ - -#ifdef CONFIG_FSL_QSPI -#define FSL_QSPI_FLASH_SIZE (1 << 24) -#define FSL_QSPI_FLASH_NUM 2 -#define CONFIG_SYS_FSL_QSPI_LE -#endif - -/* I2C Configs */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ -#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ -#define CONFIG_SYS_SPD_BUS_NUM 0 - - -#define CONFIG_SYS_LOAD_ADDR 0x82000000 - -/* We boot from the gfxRAM area of the OCRAM. */ -#define CONFIG_BOARD_SIZE_LIMIT 520192 - -/* - * We do have 128MB of memory on the Vybrid Tower board. Leave the last - * 16MB alone to avoid conflicts with Cortex-M4 firmwares running from - * DDR3. Hence, limit the memory range for image processing to 112MB - * using bootm_size. All of the following must be within this range. - * We have the default load at 32MB into DDR (for the kernel), FDT at - * 64MB and the ramdisk 512KB above that (allowing for hopefully never - * seen large trees). This allows a reasonable split between ramdisk - * and kernel size, where the ram disk can be a bit larger. - */ -#define MEM_LAYOUT_ENV_SETTINGS \ - "bootm_size=0x07000000\0" \ - "loadaddr=0x82000000\0" \ - "kernel_addr_r=0x82000000\0" \ - "fdt_addr=0x84000000\0" \ - "fdt_addr_r=0x84000000\0" \ - "rdaddr=0x84080000\0" \ - "ramdisk_addr_r=0x84080000\0" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - MEM_LAYOUT_ENV_SETTINGS \ - "script=boot.scr\0" \ - "image=zImage\0" \ - "console=ttyLP1\0" \ - "fdt_file=vf610-twr.dtb\0" \ - "boot_fdt=try\0" \ - "ip_dyn=yes\0" \ - "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \ - "mmcpart=1\0" \ - "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \ - "update_sd_firmware_filename=u-boot.imx\0" \ - "update_sd_firmware=" \ - "if test ${ip_dyn} = yes; then " \ - "setenv get_cmd dhcp; " \ - "else " \ - "setenv get_cmd tftp; " \ - "fi; " \ - "if mmc dev ${mmcdev}; then " \ - "if ${get_cmd} ${update_sd_firmware_filename}; then " \ - "setexpr fw_sz ${filesize} / 0x200; " \ - "setexpr fw_sz ${fw_sz} + 1; " \ - "mmc write ${loadaddr} 0x2 ${fw_sz}; " \ - "fi; " \ - "fi\0" \ - "mmcargs=setenv bootargs console=${console},${baudrate} " \ - "root=${mmcroot}\0" \ - "loadbootscript=" \ - "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ - "bootscript=echo Running bootscript from mmc ...; " \ - "source\0" \ - "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ - "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ - "mmcboot=echo Booting from mmc ...; " \ - "run mmcargs; " \ - "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ - "if run loadfdt; then " \ - "bootz ${loadaddr} - ${fdt_addr}; " \ - "else " \ - "if test ${boot_fdt} = try; then " \ - "bootz; " \ - "else " \ - "echo WARN: Cannot load the DT; " \ - "fi; " \ - "fi; " \ - "else " \ - "bootz; " \ - "fi;\0" \ - "netargs=setenv bootargs console=${console},${baudrate} " \ - "root=/dev/nfs " \ - "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ - "netboot=echo Booting from net ...; " \ - "run netargs; " \ - "if test ${ip_dyn} = yes; then " \ - "setenv get_cmd dhcp; " \ - "else " \ - "setenv get_cmd tftp; " \ - "fi; " \ - "${get_cmd} ${image}; " \ - "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ - "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ - "bootz ${loadaddr} - ${fdt_addr}; " \ - "else " \ - "if test ${boot_fdt} = try; then " \ - "bootz; " \ - "else " \ - "echo WARN: Cannot load the DT; " \ - "fi; " \ - "fi; " \ - "else " \ - "bootz; " \ - "fi;\0" - -#define CONFIG_BOOTCOMMAND \ - "mmc dev ${mmcdev}; if mmc rescan; then " \ - "if run loadbootscript; then " \ - "run bootscript; " \ - "else " \ - "if run loadimage; then " \ - "run mmcboot; " \ - "else run netboot; " \ - "fi; " \ - "fi; " \ - "else run netboot; fi" - -/* Miscellaneous configurable options */ - -#define CONFIG_SYS_MEMTEST_START 0x80010000 -#define CONFIG_SYS_MEMTEST_END 0x87C00000 - -/* Physical memory map */ -#define PHYS_SDRAM (0x80000000) -#define PHYS_SDRAM_SIZE (128 * 1024 * 1024) - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM -#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR -#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) - -#ifdef CONFIG_ENV_IS_IN_MMC -#define CONFIG_ENV_SIZE (8 * 1024) - -#define CONFIG_ENV_OFFSET (12 * 64 * 1024) -#define CONFIG_SYS_MMC_ENV_DEV 0 -#endif - -#ifdef CONFIG_ENV_IS_IN_NAND -#define CONFIG_ENV_SIZE (64 * 2048) -#define CONFIG_ENV_SECT_SIZE (64 * 2048) -#define CONFIG_ENV_RANGE (512 * 1024) -#define CONFIG_ENV_OFFSET 0x180000 -#endif - -#endif |