diff options
Diffstat (limited to 'include/configs/xpedite517x.h')
| -rw-r--r-- | include/configs/xpedite517x.h | 650 |
1 files changed, 0 insertions, 650 deletions
diff --git a/include/configs/xpedite517x.h b/include/configs/xpedite517x.h deleted file mode 100644 index 23f0389..0000000 --- a/include/configs/xpedite517x.h +++ /dev/null @@ -1,650 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2009 Extreme Engineering Solutions, Inc. - * Copyright 2007-2008 Freescale Semiconductor, Inc. - */ - -/* - * xpedite517x board configuration file - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_SYS_BOARD_NAME "XPedite5170" -#define CONFIG_SYS_FORM_3U_VPX 1 -#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ -#define CONFIG_BAT_RW 1 /* Use common BAT rw code */ -#define CONFIG_ALTIVEC 1 - -#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ -#define CONFIG_PCIE1 1 /* PCIE controller 1 */ -#define CONFIG_PCIE2 1 /* PCIE controller 2 */ -#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ -#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ -#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ - -/* - * DDR config - */ -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ -#define CONFIG_DDR_SPD -#define CONFIG_MEM_INIT_VALUE 0xdeadbeef -#define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */ -#define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */ -#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL 1 -#define CONFIG_DDR_ECC -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE -#define CONFIG_VERY_BIG_RAM -#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ - -/* - * virtual address to be used for temporary mappings. There - * should be 128k free at this VA. - */ -#define CONFIG_SYS_SCRATCH_VA 0xe0000000 - -#ifndef __ASSEMBLY__ -extern unsigned long get_board_sys_clk(unsigned long dummy); -#endif - -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC86xx */ - -/* - * L2CR setup - */ -#define CONFIG_SYS_L2 -#define L2_INIT 0 -#define L2_ENABLE (L2CR_L2E) - -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR -#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR - -/* - * Diagnostics - */ -#define CONFIG_SYS_MEMTEST_START 0x10000000 -#define CONFIG_SYS_MEMTEST_END 0x20000000 -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY |\ - CONFIG_SYS_POST_I2C) -/* The XPedite5170 can host an XMC which has an EEPROM at address 0x50 */ -#define I2C_ADDR_IGNORE_LIST {0x50} - -/* - * Memory map - * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable - * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable - * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable - * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable - * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable - * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable - * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable - * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable - * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable - * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable - */ - -#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_4 | LCRR_EADC_3) - -/* - * NAND flash configuration - */ -#define CONFIG_SYS_NAND_BASE 0xef800000 -#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ -#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE2} -#define CONFIG_SYS_MAX_NAND_DEVICE 2 -#define CONFIG_NAND_ACTL -#define CONFIG_SYS_NAND_ACTL_ALE (1 << 14) /* C_LA14 */ -#define CONFIG_SYS_NAND_ACTL_CLE (1 << 15) /* C_LA15 */ -#define CONFIG_SYS_NAND_ACTL_NCE 0 /* NCE not controlled by ADDR */ -#define CONFIG_SYS_NAND_ACTL_DELAY 25 -#define CONFIG_JFFS2_NAND - -/* - * NOR flash configuration - */ -#define CONFIG_SYS_FLASH_BASE 0xf8000000 -#define CONFIG_SYS_FLASH_BASE2 0xf0000000 -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff00000, 0xc0000}, \ - {0xf7f00000, 0xc0000} } -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ - -/* - * Chip select configuration - */ -/* NOR Flash 0 on CS0 */ -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE |\ - BR_PS_16 |\ - BR_V) -#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB |\ - OR_GPCM_CSNT |\ - OR_GPCM_XACS |\ - OR_GPCM_ACS_DIV2 |\ - OR_GPCM_SCY_8 |\ - OR_GPCM_TRLX |\ - OR_GPCM_EHTR |\ - OR_GPCM_EAD) - -/* NOR Flash 1 on CS1 */ -#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 |\ - BR_PS_16 |\ - BR_V) -#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM - -/* NAND flash on CS2 */ -#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE |\ - BR_PS_8 |\ - BR_V) -#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB |\ - OR_GPCM_BCTLD |\ - OR_GPCM_CSNT |\ - OR_GPCM_ACS_DIV4 |\ - OR_GPCM_SCY_4 |\ - OR_GPCM_TRLX |\ - OR_GPCM_EHTR) - -/* Optional NAND flash on CS3 */ -#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 |\ - BR_PS_8 |\ - BR_V) -#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM - -/* - * Use L1 as initial stack - */ -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * I2C - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 100000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 100000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 - -/* PEX8518 slave I2C interface */ -#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 - -/* I2C DS1631 temperature sensor */ -#define CONFIG_SYS_I2C_LM90_ADDR 0x4c - -/* I2C EEPROM - AT24C128B */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ - -/* I2C RTC */ -#define CONFIG_RTC_M41T11 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#define CONFIG_SYS_M41T11_BASE_YEAR 2000 - -/* GPIO */ -#define CONFIG_PCA953X -#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 -#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c -#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e -#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f -#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 -#define CONFIG_SYS_I2C_PCA9553_ADDR 0x62 - -/* - * PU = pulled high, PD = pulled low - * I = input, O = output, IO = input/output - */ -/* PCA9557 @ 0x18*/ -#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ -#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */ -#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ -#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */ -#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ -#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */ - -/* PCA9557 @ 0x1c*/ -#define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */ -#define CONFIG_SYS_PCA953X_PLUG_GPIO0 0x02 /* Samtec connector GPIO */ -#define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */ -#define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */ -#define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */ -#define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */ -#define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */ -#define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */ - -/* PCA9557 @ 0x1e*/ -#define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */ -#define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */ -#define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */ -#define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */ -#define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */ -#define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; VPX Geographical address parity */ -#define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; VPX P1 SYSCON */ - -/* PCA9557 @ 0x1f */ -#define CONFIG_SYS_PCA953X_VPX_GPIO0 0x01 /* PU; VPX P15 GPIO */ -#define CONFIG_SYS_PCA953X_VPX_GPIO1 0x02 /* PU; VPX P15 GPIO */ -#define CONFIG_SYS_PCA953X_VPX_GPIO2 0x04 /* PU; VPX P15 GPIO */ -#define CONFIG_SYS_PCA953X_VPX_GPIO3 0x08 /* PU; VPX P15 GPIO */ - -/* - * General PCI - * Memory space is mapped 1-1, but I/O space must start from 0. - */ -/* PCIE1 - PEX8518 */ -#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ -#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ - -/* PCIE2 - VPX P1 */ -#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 -#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ - -/* - * Networking options - */ -#define CONFIG_ETHPRIME "eTSEC1" - -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "eTSEC1" -#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC1_PHY_ADDR 1 -#define TSEC1_PHYIDX 0 -#define CONFIG_HAS_ETH0 - -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "eTSEC2" -#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC2_PHY_ADDR 2 -#define TSEC2_PHYIDX 0 -#define CONFIG_HAS_ETH1 - -/* - * BAT mappings - */ -#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) -#define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT |\ - BATL_PP_RW |\ - BATL_CACHEINHIBIT |\ - BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT |\ - BATU_BL_1M |\ - BATU_VS |\ - BATU_VP) -#define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT |\ - BATL_PP_RW |\ - BATL_CACHEINHIBIT) -#define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU -#endif - -/* - * BAT0 2G Cacheable, non-guarded - * 0x0000_0000 2G DDR - */ -#define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) -#define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U - -/* - * BAT1 1G Cache-inhibited, guarded - * 0x8000_0000 1G PCI-Express 1 Memory - */ -#define CONFIG_SYS_DBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS |\ - BATL_PP_RW |\ - BATL_CACHEINHIBIT |\ - BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCIE1_MEM_PHYS |\ - BATU_BL_1G |\ - BATU_VS |\ - BATU_VP) -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS |\ - BATL_PP_RW |\ - BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U - -/* - * BAT2 512M Cache-inhibited, guarded - * 0xc000_0000 512M PCI-Express 2 Memory - */ -#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCIE2_MEM_PHYS |\ - BATL_PP_RW |\ - BATL_CACHEINHIBIT |\ - BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE2_MEM_PHYS |\ - BATU_BL_512M |\ - BATU_VS |\ - BATU_VP) -#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCIE2_MEM_PHYS |\ - BATL_PP_RW |\ - BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U - -/* - * BAT3 1M Cache-inhibited, guarded - * 0xe000_0000 1M CCSR - */ -#define CONFIG_SYS_DBAT3L (CONFIG_SYS_CCSRBAR |\ - BATL_PP_RW |\ - BATL_CACHEINHIBIT |\ - BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR |\ - BATU_BL_1M |\ - BATU_VS |\ - BATU_VP) -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR |\ - BATL_PP_RW |\ - BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U - -/* - * BAT4 32M Cache-inhibited, guarded - * 0xe200_0000 16M PCI-Express 1 I/O - * 0xe300_0000 16M PCI-Express 2 I/0 - */ -#define CONFIG_SYS_DBAT4L (CONFIG_SYS_PCIE1_IO_PHYS |\ - BATL_PP_RW |\ - BATL_CACHEINHIBIT |\ - BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_PHYS |\ - BATU_BL_32M |\ - BATU_VS |\ - BATU_VP) -#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE1_IO_PHYS |\ - BATL_PP_RW |\ - BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U - -/* - * BAT5 128K Cacheable, non-guarded - * 0xe400_1000 128K Init RAM for stack in the CPU DCache (no backing memory) - */ -#define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR |\ - BATL_PP_RW |\ - BATL_MEMCOHERENCE) -#define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR |\ - BATU_BL_128K |\ - BATU_VS |\ - BATU_VP) -#define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L -#define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U - -/* - * BAT6 256M Cache-inhibited, guarded - * 0xf000_0000 256M FLASH - */ -#define CONFIG_SYS_DBAT6L (CONFIG_SYS_FLASH_BASE2 |\ - BATL_PP_RW |\ - BATL_CACHEINHIBIT |\ - BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE |\ - BATU_BL_256M |\ - BATU_VS |\ - BATU_VP) -#define CONFIG_SYS_IBAT6L (CONFIG_SYS_FLASH_BASE |\ - BATL_PP_RW |\ - BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U - -/* Map the last 1M of flash where we're running from reset */ -#define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY |\ - BATL_PP_RW |\ - BATL_CACHEINHIBIT |\ - BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE |\ - BATU_BL_1M |\ - BATU_VS |\ - BATU_VP) -#define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY |\ - BATL_PP_RW |\ - BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY - -/* - * BAT7 64M Cache-inhibited, guarded - * 0xe800_0000 64K NAND FLASH - * 0xe804_0000 128K DUART Registers - */ -#define CONFIG_SYS_DBAT7L (CONFIG_SYS_NAND_BASE |\ - BATL_PP_RW |\ - BATL_CACHEINHIBIT |\ - BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT7U (CONFIG_SYS_NAND_BASE |\ - BATU_BL_512K |\ - BATU_VS |\ - BATU_VP) -#define CONFIG_SYS_IBAT7L (CONFIG_SYS_NAND_BASE |\ - BATL_PP_RW |\ - BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT7U CONFIG_SYS_DBAT7U - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ -#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ -#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 16 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ - -/* - * Environment Configuration - */ -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ -#define CONFIG_ENV_SIZE 0x8000 -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) - -/* - * Flash memory map: - * fffc0000 - ffffffff Pri FDT (256KB) - * fff80000 - fffbffff Pri U-Boot Environment (256 KB) - * fff00000 - fff7ffff Pri U-Boot (512 KB) - * fef00000 - ffefffff Pri OS image (16MB) - * f8000000 - feefffff Pri OS Use/Filesystem (111MB) - * - * f7fc0000 - f7ffffff Sec FDT (256KB) - * f7f80000 - f7fbffff Sec U-Boot Environment (256 KB) - * f7f00000 - f7f7ffff Sec U-Boot (512 KB) - * f6f00000 - f7efffff Sec OS image (16MB) - * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) - */ -#define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff00000) -#define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f00000) -#define CONFIG_FDT1_ENV_ADDR __stringify(0xfffc0000) -#define CONFIG_FDT2_ENV_ADDR __stringify(0xf7fc0000) -#define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) -#define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000) - -#define CONFIG_PROG_UBOOT1 \ - "$download_cmd $loadaddr $ubootfile; " \ - "if test $? -eq 0; then " \ - "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ - "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ - "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ - "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ - "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ - "if test $? -ne 0; then " \ - "echo PROGRAM FAILED; " \ - "else; " \ - "echo PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_UBOOT2 \ - "$download_cmd $loadaddr $ubootfile; " \ - "if test $? -eq 0; then " \ - "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ - "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ - "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ - "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ - "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ - "if test $? -ne 0; then " \ - "echo PROGRAM FAILED; " \ - "else; " \ - "echo PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_BOOT_OS_NET \ - "$download_cmd $osaddr $osfile; " \ - "if test $? -eq 0; then " \ - "if test -n $fdtaddr; then " \ - "$download_cmd $fdtaddr $fdtfile; " \ - "if test $? -eq 0; then " \ - "bootm $osaddr - $fdtaddr; " \ - "else; " \ - "echo FDT DOWNLOAD FAILED; " \ - "fi; " \ - "else; " \ - "bootm $osaddr; " \ - "fi; " \ - "else; " \ - "echo OS DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_OS1 \ - "$download_cmd $osaddr $osfile; " \ - "if test $? -eq 0; then " \ - "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ - "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ - "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ - "if test $? -ne 0; then " \ - "echo OS PROGRAM FAILED; " \ - "else; " \ - "echo OS PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo OS DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_OS2 \ - "$download_cmd $osaddr $osfile; " \ - "if test $? -eq 0; then " \ - "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ - "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ - "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ - "if test $? -ne 0; then " \ - "echo OS PROGRAM FAILED; " \ - "else; " \ - "echo OS PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo OS DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_FDT1 \ - "$download_cmd $fdtaddr $fdtfile; " \ - "if test $? -eq 0; then " \ - "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ - "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ - "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ - "if test $? -ne 0; then " \ - "echo FDT PROGRAM FAILED; " \ - "else; " \ - "echo FDT PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo FDT DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_FDT2 \ - "$download_cmd $fdtaddr $fdtfile; " \ - "if test $? -eq 0; then " \ - "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ - "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ - "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ - "if test $? -ne 0; then " \ - "echo FDT PROGRAM FAILED; " \ - "else; " \ - "echo FDT PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo FDT DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "autoload=yes\0" \ - "download_cmd=tftp\0" \ - "console_args=console=ttyS0,115200\0" \ - "root_args=root=/dev/nfs rw\0" \ - "misc_args=ip=on\0" \ - "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ - "bootfile=/home/user/file\0" \ - "osfile=/home/user/board.uImage\0" \ - "fdtfile=/home/user/board.dtb\0" \ - "ubootfile=/home/user/u-boot.bin\0" \ - "fdtaddr=0x1e00000\0" \ - "osaddr=0x1000000\0" \ - "loadaddr=0x1000000\0" \ - "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ - "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ - "prog_os1="CONFIG_PROG_OS1"\0" \ - "prog_os2="CONFIG_PROG_OS2"\0" \ - "prog_fdt1="CONFIG_PROG_FDT1"\0" \ - "prog_fdt2="CONFIG_PROG_FDT2"\0" \ - "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ - "bootcmd_flash1=run set_bootargs; " \ - "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ - "bootcmd_flash2=run set_bootargs; " \ - "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ - "bootcmd=run bootcmd_flash1\0" -#endif /* __CONFIG_H */ |