diff options
Diffstat (limited to 'include/configs/xpedite520x.h')
| -rw-r--r-- | include/configs/xpedite520x.h | 450 |
1 files changed, 0 insertions, 450 deletions
diff --git a/include/configs/xpedite520x.h b/include/configs/xpedite520x.h deleted file mode 100644 index 21e91ee..0000000 --- a/include/configs/xpedite520x.h +++ /dev/null @@ -1,450 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2008 Extreme Engineering Solutions, Inc. - * Copyright 2004-2008 Freescale Semiconductor, Inc. - */ - -/* - * xpedite520x board configuration file - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_SYS_BOARD_NAME "XPedite5200" -#define CONFIG_SYS_FORM_PMC_XMC 1 - -#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ -#define CONFIG_PCI1 1 /* PCI controller 1 */ -#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ -#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ -#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ - -/* - * DDR config - */ -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ -#define CONFIG_DDR_SPD -#define CONFIG_MEM_INIT_VALUE 0xdeadbeef -#define SPD_EEPROM_ADDRESS 0x54 -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL 2 -#define CONFIG_DDR_ECC -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE -#define CONFIG_VERY_BIG_RAM - -#define CONFIG_SYS_CLK_FREQ 66666666 - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_ENABLE_36BIT_PHYS 1 - -#define CONFIG_SYS_CCSRBAR 0xef000000 -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR - -/* - * Diagnostics - */ -#define CONFIG_SYS_MEMTEST_START 0x10000000 -#define CONFIG_SYS_MEMTEST_END 0x20000000 -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_I2C) -#define I2C_ADDR_LIST {CONFIG_SYS_I2C_MAX1237_ADDR, \ - CONFIG_SYS_I2C_EEPROM_ADDR, \ - CONFIG_SYS_I2C_PCA953X_ADDR0, \ - CONFIG_SYS_I2C_PCA953X_ADDR1, \ - CONFIG_SYS_I2C_RTC_ADDR} - -/* - * Memory map - * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable - * 0x8000_0000 0xbfff_ffff PCI1 Mem 1G non-cacheable - * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable - * 0xe800_0000 0xe87f_ffff PCI1 IO 8M non-cacheable - * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable - * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable - * 0xf800_0000 0xfbff_ffff NOR Flash 2 64M non-cacheable - * 0xfc00_0000 0xffff_ffff NOR Flash 1 64M non-cacheable - */ - -#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) - -/* - * NAND flash configuration - */ -#define CONFIG_SYS_NAND_BASE 0xef800000 -#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_NAND_ACTL -#define CONFIG_SYS_NAND_ACTL_CLE (1 << 3) /* ADDR3 is CLE */ -#define CONFIG_SYS_NAND_ACTL_ALE (1 << 4) /* ADDR4 is ALE */ -#define CONFIG_SYS_NAND_ACTL_NCE (0) /* NCE not controlled by ADDR */ -#define CONFIG_SYS_NAND_ACTL_DELAY 25 - -/* - * NOR flash configuration - */ -#define CONFIG_SYS_FLASH_BASE 0xfc000000 -#define CONFIG_SYS_FLASH_BASE2 0xf8000000 -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ - {0xfbf40000, 0xc0000} } -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -/* - * Chip select configuration - */ -/* NOR Flash 0 on CS0 */ -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ - BR_PS_16 | \ - BR_V) -#define CONFIG_SYS_OR0_PRELIM (OR_AM_64MB | \ - OR_GPCM_ACS_DIV4 | \ - OR_GPCM_SCY_8) - -/* NOR Flash 1 on CS1 */ -#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ - BR_PS_16 | \ - BR_V) -#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM - -/* NAND flash on CS2 */ -#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ - BR_PS_8 | \ - BR_V) - -/* NAND flash on CS2 */ -#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ - OR_GPCM_BCTLD | \ - OR_GPCM_CSNT | \ - OR_GPCM_ACS_DIV4 | \ - OR_GPCM_SCY_4 | \ - OR_GPCM_TRLX | \ - OR_GPCM_EHTR) - -/* NAND flash on CS3 */ -#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ - BR_PS_8 | \ - BR_V) -#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM - -/* - * Use L1 as initial stack - */ -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * I2C - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 - -/* I2C EEPROM */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ - -/* I2C RTC */ -#define CONFIG_RTC_M41T11 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#define CONFIG_SYS_M41T11_BASE_YEAR 2000 - -/* GPIO */ -#define CONFIG_PCA953X -#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 -#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x19 -#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 - -/* PCA957 @ 0x18 */ -#define CONFIG_SYS_PCA953X_BRD_CFG0 0x01 -#define CONFIG_SYS_PCA953X_BRD_CFG1 0x02 -#define CONFIG_SYS_PCA953X_BRD_CFG2 0x04 -#define CONFIG_SYS_PCA953X_XMC_ROOT0 0x08 -#define CONFIG_SYS_PCA953X_FLASH_PASS_CS 0x10 -#define CONFIG_SYS_PCA953X_NVM_WP 0x20 -#define CONFIG_SYS_PCA953X_MONARCH 0x40 -#define CONFIG_SYS_PCA953X_EREADY 0x80 - -/* PCA957 @ 0x19 */ -#define CONFIG_SYS_PCA953X_P14_IO0 0x01 -#define CONFIG_SYS_PCA953X_P14_IO1 0x02 -#define CONFIG_SYS_PCA953X_P14_IO2 0x04 -#define CONFIG_SYS_PCA953X_P14_IO3 0x08 -#define CONFIG_SYS_PCA953X_P14_IO4 0x10 -#define CONFIG_SYS_PCA953X_P14_IO5 0x20 -#define CONFIG_SYS_PCA953X_P14_IO6 0x40 -#define CONFIG_SYS_PCA953X_P14_IO7 0x80 - -/* 12-bit ADC used to measure CPU diode */ -#define CONFIG_SYS_I2C_MAX1237_ADDR 0x34 - -/* - * General PCI - * Memory space is mapped 1-1, but I/O space must start from 0. - */ -#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS -#define CONFIG_SYS_PCI1_MEM_SIZE 0x40000000 /* 1G */ -#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xe8000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 1M */ - -/* - * Networking options - */ -#define CONFIG_ETHPRIME "eTSEC1" - -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "eTSEC1" -#define TSEC1_FLAGS TSEC_GIGABIT -#define TSEC1_PHY_ADDR 1 -#define TSEC1_PHYIDX 0 -#define CONFIG_HAS_ETH0 - -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "eTSEC2" -#define TSEC2_FLAGS TSEC_GIGABIT -#define TSEC2_PHY_ADDR 2 -#define TSEC2_PHYIDX 0 -#define CONFIG_HAS_ETH1 - -#define CONFIG_TSEC3 1 -#define CONFIG_TSEC3_NAME "eTSEC3" -#define TSEC3_FLAGS TSEC_GIGABIT -#define TSEC3_PHY_ADDR 3 -#define TSEC3_PHYIDX 0 -#define CONFIG_HAS_ETH2 - -#define CONFIG_TSEC4 1 -#define CONFIG_TSEC4_NAME "eTSEC4" -#define TSEC4_FLAGS TSEC_GIGABIT -#define TSEC4_PHY_ADDR 4 -#define TSEC4_PHYIDX 0 -#define CONFIG_HAS_ETH3 - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ -#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ -#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ -#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 16 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ - -/* - * Environment Configuration - */ -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ -#define CONFIG_ENV_SIZE 0x8000 -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) - -/* - * Flash memory map: - * fff80000 - ffffffff Pri U-Boot (512 KB) - * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) - * fff00000 - fff3ffff Pri FDT (256KB) - * fef00000 - ffefffff Pri OS image (16MB) - * fc000000 - feefffff Pri OS Use/Filesystem (47MB) - * - * fbf80000 - fbffffff Sec U-Boot (512 KB) - * fbf40000 - fbf7ffff Sec U-Boot Environment (256 KB) - * fbf00000 - fbf3ffff Sec FDT (256KB) - * faf00000 - fbefffff Sec OS image (16MB) - * f8000000 - faefffff Sec OS Use/Filesystem (47MB) - */ -#define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000) -#define CONFIG_UBOOT2_ENV_ADDR __stringify(0xfbf80000) -#define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000) -#define CONFIG_FDT2_ENV_ADDR __stringify(0xfbf00000) -#define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) -#define CONFIG_OS2_ENV_ADDR __stringify(0xfaf00000) - -#define CONFIG_PROG_UBOOT1 \ - "$download_cmd $loadaddr $ubootfile; " \ - "if test $? -eq 0; then " \ - "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ - "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ - "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ - "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ - "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ - "if test $? -ne 0; then " \ - "echo PROGRAM FAILED; " \ - "else; " \ - "echo PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_UBOOT2 \ - "$download_cmd $loadaddr $ubootfile; " \ - "if test $? -eq 0; then " \ - "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ - "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ - "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ - "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ - "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ - "if test $? -ne 0; then " \ - "echo PROGRAM FAILED; " \ - "else; " \ - "echo PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_BOOT_OS_NET \ - "$download_cmd $osaddr $osfile; " \ - "if test $? -eq 0; then " \ - "if test -n $fdtaddr; then " \ - "$download_cmd $fdtaddr $fdtfile; " \ - "if test $? -eq 0; then " \ - "bootm $osaddr - $fdtaddr; " \ - "else; " \ - "echo FDT DOWNLOAD FAILED; " \ - "fi; " \ - "else; " \ - "bootm $osaddr; " \ - "fi; " \ - "else; " \ - "echo OS DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_OS1 \ - "$download_cmd $osaddr $osfile; " \ - "if test $? -eq 0; then " \ - "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ - "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ - "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ - "if test $? -ne 0; then " \ - "echo OS PROGRAM FAILED; " \ - "else; " \ - "echo OS PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo OS DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_OS2 \ - "$download_cmd $osaddr $osfile; " \ - "if test $? -eq 0; then " \ - "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ - "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ - "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ - "if test $? -ne 0; then " \ - "echo OS PROGRAM FAILED; " \ - "else; " \ - "echo OS PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo OS DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_FDT1 \ - "$download_cmd $fdtaddr $fdtfile; " \ - "if test $? -eq 0; then " \ - "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ - "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ - "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ - "if test $? -ne 0; then " \ - "echo FDT PROGRAM FAILED; " \ - "else; " \ - "echo FDT PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo FDT DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_FDT2 \ - "$download_cmd $fdtaddr $fdtfile; " \ - "if test $? -eq 0; then " \ - "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ - "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ - "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ - "if test $? -ne 0; then " \ - "echo FDT PROGRAM FAILED; " \ - "else; " \ - "echo FDT PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo FDT DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "autoload=yes\0" \ - "download_cmd=tftp\0" \ - "console_args=console=ttyS0,115200\0" \ - "root_args=root=/dev/nfs rw\0" \ - "misc_args=ip=on\0" \ - "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ - "bootfile=/home/user/file\0" \ - "osfile=/home/user/board.uImage\0" \ - "fdtfile=/home/user/board.dtb\0" \ - "ubootfile=/home/user/u-boot.bin\0" \ - "fdtaddr=0x1e00000\0" \ - "osaddr=0x1000000\0" \ - "loadaddr=0x1000000\0" \ - "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ - "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ - "prog_os1="CONFIG_PROG_OS1"\0" \ - "prog_os2="CONFIG_PROG_OS2"\0" \ - "prog_fdt1="CONFIG_PROG_FDT1"\0" \ - "prog_fdt2="CONFIG_PROG_FDT2"\0" \ - "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ - "bootcmd_flash1=run set_bootargs; " \ - "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ - "bootcmd_flash2=run set_bootargs; " \ - "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ - "bootcmd=run bootcmd_flash1\0" -#endif /* __CONFIG_H */ |