diff options
Diffstat (limited to 'include/configs/M5272C3.h')
| -rw-r--r-- | include/configs/M5272C3.h | 200 |
1 files changed, 200 insertions, 0 deletions
diff --git a/include/configs/M5272C3.h b/include/configs/M5272C3.h new file mode 100644 index 0000000..9d3bf42 --- /dev/null +++ b/include/configs/M5272C3.h @@ -0,0 +1,200 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Configuation settings for the Motorola MC5272C3 board. + * + * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de> + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef _M5272C3_H +#define _M5272C3_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_MCFTMR + +#define CONFIG_MCFUART +#define CONFIG_SYS_UART_PORT (0) + +#undef CONFIG_WATCHDOG +#define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */ + +#undef CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */ + +/* Configuration for environment + * Environment is embedded in u-boot in the second sector of the flash + */ +#ifndef CONFIG_MONITOR_IS_IN_RAM +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_SECT_SIZE 0x2000 +#else +#define CONFIG_ENV_ADDR 0xffe04000 +#define CONFIG_ENV_SECT_SIZE 0x2000 +#endif + +#define LDS_BOARD_TEXT \ + . = DEFINED(env_offset) ? env_offset : .; \ + env/embedded.o(.text); + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE + +/* + * Command line configuration. + */ + +#define CONFIG_MCFFEC +#ifdef CONFIG_MCFFEC +# define CONFIG_MII_INIT 1 +# define CONFIG_SYS_DISCOVER_PHY +# define CONFIG_SYS_RX_ETH_BUFFER 8 +# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN + +# define CONFIG_SYS_FEC0_PINMUX 0 +# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE +# define MCFFEC_TOUT_LOOP 50000 +/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CONFIG_SYS_DISCOVER_PHY +# define FECDUPLEX FULL +# define FECSPEED _100BASET +# else +# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN +# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN +# endif +# endif /* CONFIG_SYS_DISCOVER_PHY */ +#endif + +#ifdef CONFIG_MCFFEC +# define CONFIG_IPADDR 192.162.1.2 +# define CONFIG_NETMASK 255.255.255.0 +# define CONFIG_SERVERIP 192.162.1.1 +# define CONFIG_GATEWAYIP 192.162.1.1 +#endif /* CONFIG_MCFFEC */ + +#define CONFIG_HOSTNAME "M5272C3" +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "loadaddr=10000\0" \ + "u-boot=u-boot.bin\0" \ + "load=tftp ${loadaddr) ${u-boot}\0" \ + "upd=run load; run prog\0" \ + "prog=prot off ffe00000 ffe3ffff;" \ + "era ffe00000 ffe3ffff;" \ + "cp.b ${loadaddr} ffe00000 ${filesize};"\ + "save\0" \ + "" + +#define CONFIG_SYS_LOAD_ADDR 0x20000 +#define CONFIG_SYS_MEMTEST_START 0x400 +#define CONFIG_SYS_MEMTEST_END 0x380000 +#define CONFIG_SYS_CLK 66000000 + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ +#define CONFIG_SYS_SCR 0x0003 +#define CONFIG_SYS_SPR 0xffff + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_SIZE 4 /* SDRAM size in MB */ +#define CONFIG_SYS_FLASH_BASE 0xffe00000 + +#ifdef CONFIG_MONITOR_IS_IN_RAM +#define CONFIG_SYS_MONITOR_BASE 0x20000 +#else +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) +#endif + +#define CONFIG_SYS_MONITOR_LEN 0x20000 +#define CONFIG_SYS_MALLOC_LEN (256 << 10) +#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization ?? + */ +#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) + +/* + * FLASH organization + */ +#ifdef CONFIG_SYS_FLASH_CFI +# define CONFIG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */ +# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT +# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ +#endif + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CONFIG_SYS_CACHELINE_SIZE 16 + +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ + CF_CACR_DISD | CF_CACR_INVI | \ + CF_CACR_CEIB | CF_CACR_DCM | \ + CF_CACR_EUSP) + +/*----------------------------------------------------------------------- + * Memory bank definitions + */ +#define CONFIG_SYS_BR0_PRELIM 0xFFE00201 +#define CONFIG_SYS_OR0_PRELIM 0xFFE00014 +#define CONFIG_SYS_BR1_PRELIM 0 +#define CONFIG_SYS_OR1_PRELIM 0 +#define CONFIG_SYS_BR2_PRELIM 0x30000001 +#define CONFIG_SYS_OR2_PRELIM 0xFFF80000 +#define CONFIG_SYS_BR3_PRELIM 0 +#define CONFIG_SYS_OR3_PRELIM 0 +#define CONFIG_SYS_BR4_PRELIM 0 +#define CONFIG_SYS_OR4_PRELIM 0 +#define CONFIG_SYS_BR5_PRELIM 0 +#define CONFIG_SYS_OR5_PRELIM 0 +#define CONFIG_SYS_BR6_PRELIM 0 +#define CONFIG_SYS_OR6_PRELIM 0 +#define CONFIG_SYS_BR7_PRELIM 0x00000701 +#define CONFIG_SYS_OR7_PRELIM 0xFFC0007C + +/*----------------------------------------------------------------------- + * Port configuration + */ +#define CONFIG_SYS_PACNT 0x00000000 +#define CONFIG_SYS_PADDR 0x0000 +#define CONFIG_SYS_PADAT 0x0000 +#define CONFIG_SYS_PBCNT 0x55554155 /* Ethernet/UART configuration */ +#define CONFIG_SYS_PBDDR 0x0000 +#define CONFIG_SYS_PBDAT 0x0000 +#define CONFIG_SYS_PDCNT 0x00000000 +#endif /* _M5272C3_H */ |