diff options
Diffstat (limited to 'include/configs/MPC8313ERDB_NAND.h')
| -rw-r--r-- | include/configs/MPC8313ERDB_NAND.h | 404 |
1 files changed, 404 insertions, 0 deletions
diff --git a/include/configs/MPC8313ERDB_NAND.h b/include/configs/MPC8313ERDB_NAND.h new file mode 100644 index 0000000..4153d60 --- /dev/null +++ b/include/configs/MPC8313ERDB_NAND.h @@ -0,0 +1,404 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) Freescale Semiconductor, Inc. 2006, 2010. + */ +/* + * mpc8313epb board configuration file + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 + +#define CONFIG_SPL_INIT_MINIMAL +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" +#define CONFIG_SPL_MPC83XX_WAIT_FOR_NAND + +#ifdef CONFIG_SPL_BUILD +#define CONFIG_NS16550_MIN_FUNCTIONS +#endif + +#define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000 +#define CONFIG_SPL_MAX_SIZE (4 * 1024) +#define CONFIG_SPL_PAD_TO 0x4000 + +#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 +#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100 +#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384 +#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000 +#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000) + +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */ +#endif + +#ifndef CONFIG_SYS_MONITOR_BASE +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#endif + +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_FSL_ELBC 1 + +/* + * On-board devices + * + * TSEC1 is VSC switch + * TSEC2 is SoC TSEC + */ +#define CONFIG_VSC7385_ENET +#define CONFIG_TSEC2 + +#if !defined(CONFIG_SPL_BUILD) +#define CONFIG_DEFAULT_IMMR CONFIG_SYS_IMMR +#endif + +#define CONFIG_SYS_MEMTEST_START 0x00001000 +#define CONFIG_SYS_MEMTEST_END 0x07f00000 + +/* Early revs of this board will lock up hard when attempting + * to access the PMC registers, unless a JTAG debugger is + * connected, or some resistor modifications are made. + */ +#define CONFIG_SYS_8313ERDB_BROKEN_PMC 1 + +/* + * Device configurations + */ + +/* Vitesse 7385 */ + +#ifdef CONFIG_VSC7385_ENET + +#define CONFIG_TSEC1 + +/* The flash address and size of the VSC7385 firmware image */ +#define CONFIG_VSC7385_IMAGE 0xFE7FE000 +#define CONFIG_VSC7385_IMAGE_SIZE 8192 + +#endif + +/* + * DDR Setup + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory*/ + +/* + * Manually set up DDR parameters, as this board does not + * seem to have the SPD connected to I2C. + */ +#define CONFIG_SYS_DDR_SIZE 128 /* MB */ +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ + | CSCONFIG_ODT_RD_NEVER \ + | CSCONFIG_ODT_WR_ONLY_CURRENT \ + | CSCONFIG_ROW_BIT_13 \ + | CSCONFIG_COL_BIT_10) + /* 0x80010102 */ + +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 +#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ + | (0 << TIMING_CFG0_WRT_SHIFT) \ + | (0 << TIMING_CFG0_RRT_SHIFT) \ + | (0 << TIMING_CFG0_WWT_SHIFT) \ + | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ + | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ + | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ + | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) + /* 0x00220802 */ +#define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \ + | (8 << TIMING_CFG1_ACTTOPRE_SHIFT) \ + | (3 << TIMING_CFG1_ACTTORW_SHIFT) \ + | (5 << TIMING_CFG1_CASLAT_SHIFT) \ + | (10 << TIMING_CFG1_REFREC_SHIFT) \ + | (3 << TIMING_CFG1_WRREC_SHIFT) \ + | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ + | (2 << TIMING_CFG1_WRTORD_SHIFT)) + /* 0x3835a322 */ +#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ + | (5 << TIMING_CFG2_CPO_SHIFT) \ + | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ + | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ + | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ + | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ + | (6 << TIMING_CFG2_FOUR_ACT_SHIFT)) + /* 0x129048c6 */ /* P9-45,may need tuning */ +#define CONFIG_SYS_DDR_INTERVAL ((1296 << SDRAM_INTERVAL_REFINT_SHIFT) \ + | (1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) + /* 0x05100500 */ +#if defined(CONFIG_DDR_2T_TIMING) +#define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN \ + | SDRAM_CFG_SDRAM_TYPE_DDR2 \ + | SDRAM_CFG_DBW_32 \ + | SDRAM_CFG_2T_EN) + /* 0x43088000 */ +#else +#define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN \ + | SDRAM_CFG_SDRAM_TYPE_DDR2 \ + | SDRAM_CFG_DBW_32) + /* 0x43080000 */ +#endif +#define CONFIG_SYS_SDRAM_CFG2 0x00401000 +/* set burst length to 8 for 32-bit data path */ +#define CONFIG_SYS_DDR_MODE ((0x4448 << SDRAM_MODE_ESD_SHIFT) \ + | (0x0632 << SDRAM_MODE_SD_SHIFT)) + /* 0x44480632 */ +#define CONFIG_SYS_DDR_MODE_2 0x8000C000 + +#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 + /*0x02000000*/ +#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ + | DDRCDR_PZ_NOMZ \ + | DDRCDR_NZ_NOMZ \ + | DDRCDR_M_ODR) + +/* + * FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */ +#define CONFIG_SYS_FLASH_SIZE 8 /* flash size in MB */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 135 /* sectors per device */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) && \ + !defined(CONFIG_SPL_BUILD) +#define CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ + +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ + +/* drivers/mtd/nand/raw/nand.c */ +#if defined(CONFIG_SPL_BUILD) +#define CONFIG_SYS_NAND_BASE 0xFFF00000 +#else +#define CONFIG_SYS_NAND_BASE 0xE2800000 +#endif + +#define CONFIG_MTD_PARTITION + +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_NAND_FSL_ELBC 1 +#define CONFIG_SYS_NAND_BLOCK_SIZE 16384 +#define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024) + +/* Still needed for spl_minimal.c */ +#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR0_PRELIM +#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR0_PRELIM + +/* local bus write LED / read status buffer (BCSR) mapping */ +#define CONFIG_SYS_BCSR_ADDR 0xFA000000 +#define CONFIG_SYS_BCSR_SIZE (32 * 1024) /* 0x00008000 */ + /* map at 0xFA000000 on LCS3 */ + +/* Vitesse 7385 */ + +#ifdef CONFIG_VSC7385_ENET + + /* VSC7385 Base address on LCS2 */ +#define CONFIG_SYS_VSC7385_BASE 0xF0000000 +#define CONFIG_SYS_VSC7385_SIZE (128 * 1024) /* 0x00020000 */ + + +#endif + +#define CONFIG_MPC83XX_GPIO 1 + +/* + * Serial Port + */ +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 +#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE +#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 +#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ + +/* + * TSEC + */ + +#define CONFIG_GMII /* MII PHY management */ + +#ifdef CONFIG_TSEC1 +#define CONFIG_HAS_ETH0 +#define CONFIG_TSEC1_NAME "TSEC0" +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define TSEC1_PHY_ADDR 0x1c +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC1_PHYIDX 0 +#endif + +#ifdef CONFIG_TSEC2 +#define CONFIG_HAS_ETH1 +#define CONFIG_TSEC2_NAME "TSEC1" +#define CONFIG_SYS_TSEC2_OFFSET 0x25000 +#define TSEC2_PHY_ADDR 4 +#define TSEC2_FLAGS TSEC_GIGABIT +#define TSEC2_PHYIDX 0 +#endif + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC1" + +/* + * Configure on-board RTC + */ +#define CONFIG_RTC_DS1337 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 + +/* + * Environment + */ +#define CONFIG_ENV_OFFSET (512 * 1024) +#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE +#define CONFIG_ENV_RANGE (CONFIG_ENV_SECT_SIZE * 4) +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE) + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE + +/* + * Command line configuration. + */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ + + /* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +/* + * For booting Linux, the board info and command line data + * have to be in the first 256 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ + /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ + +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)) + +/* System IO Config */ +#define CONFIG_SYS_SICRH (SICRH_TSOBI1 | SICRH_TSOBI2) /* RGMII */ + /* Enable Internal USB Phy and GPIO on LCD Connector */ +#define CONFIG_SYS_SICRL (SICRL_USBDR_10 | SICRL_LBC) + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_NETDEV "eth1" + +#define CONFIG_HOSTNAME "mpc8313erdb" +#define CONFIG_ROOTPATH "/nfs/root/path" +#define CONFIG_BOOTFILE "uImage" + /* U-Boot image on TFTP server */ +#define CONFIG_UBOOTPATH "u-boot.bin" +#define CONFIG_FDTFILE "mpc8313erdb.dtb" + + /* default location for tftp and bootm */ +#define CONFIG_LOADADDR 800000 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=" CONFIG_NETDEV "\0" \ + "ethprime=TSEC1\0" \ + "uboot=" CONFIG_UBOOTPATH "\0" \ + "tftpflash=tftpboot $loadaddr $uboot; " \ + "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ + " +$filesize; " \ + "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ + " +$filesize; " \ + "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ + " $filesize; " \ + "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ + " +$filesize; " \ + "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ + " $filesize\0" \ + "fdtaddr=780000\0" \ + "fdtfile=" CONFIG_FDTFILE "\0" \ + "console=ttyS0\0" \ + "setbootargs=setenv bootargs " \ + "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \ + "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"\ + "$netdev:off " \ + "root=$rootdev rw console=$console,$baudrate $othbootargs\0" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv rootdev /dev/nfs;" \ + "run setbootargs;" \ + "run setipargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv rootdev /dev/ram;" \ + "run setbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#endif /* __CONFIG_H */ |