diff options
Diffstat (limited to 'include/configs/MPC837XERDB.h')
| -rw-r--r-- | include/configs/MPC837XERDB.h | 428 |
1 files changed, 428 insertions, 0 deletions
diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h new file mode 100644 index 0000000..37f51ba --- /dev/null +++ b/include/configs/MPC837XERDB.h @@ -0,0 +1,428 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2007 Freescale Semiconductor, Inc. + * Kevin Lam <kevin.lam@freescale.com> + * Joe D'Abbraccio <joe.d'abbraccio@freescale.com> + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ + +#define CONFIG_HWCONFIG + +/* + * On-board devices + */ +#define CONFIG_VSC7385_ENET + +/* System performance - define the value i.e. CONFIG_SYS_XXX +*/ + +/* System Clock Configuration Register */ +#define CONFIG_SYS_SCCR_TSEC1CM 1 /* eTSEC1 clock mode (0-3) */ +#define CONFIG_SYS_SCCR_TSEC2CM 1 /* eTSEC2 clock mode (0-3) */ +#define CONFIG_SYS_SCCR_SATACM SCCR_SATACM_2 /* SATA1-4 clock mode (0-3) */ + +/* + * System IO Config + */ +#define CONFIG_SYS_SICRH 0x08200000 +#define CONFIG_SYS_SICRL 0x00000000 + +/* + * Output Buffer Impedance + */ +#define CONFIG_SYS_OBIR 0x30100000 + +/* + * Device configurations + */ + +/* Vitesse 7385 */ + +#ifdef CONFIG_VSC7385_ENET + +#define CONFIG_TSEC2 + +/* The flash address and size of the VSC7385 firmware image */ +#define CONFIG_VSC7385_IMAGE 0xFE7FE000 +#define CONFIG_VSC7385_IMAGE_SIZE 8192 + +#endif + +/* + * DDR Setup + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x03000000 +#define CONFIG_SYS_83XX_DDR_USES_CS0 + +#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN | DDRCDR_ODT | DDRCDR_Q_DRN) + +#undef CONFIG_DDR_ECC /* support DDR ECC function */ +#undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ + +#undef CONFIG_NEVER_ASSERT_ODT_TO_CPU /* Never assert ODT to internal IOs */ + +/* + * Manually set up DDR parameters + */ +#define CONFIG_SYS_DDR_SIZE 256 /* MB */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ + | CSCONFIG_ODT_WR_ONLY_CURRENT \ + | CSCONFIG_ROW_BIT_13 \ + | CSCONFIG_COL_BIT_10) + +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 +#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ + | (0 << TIMING_CFG0_WRT_SHIFT) \ + | (0 << TIMING_CFG0_RRT_SHIFT) \ + | (0 << TIMING_CFG0_WWT_SHIFT) \ + | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ + | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ + | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ + | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) + /* 0x00260802 */ /* DDR400 */ +#define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \ + | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \ + | (3 << TIMING_CFG1_ACTTORW_SHIFT) \ + | (7 << TIMING_CFG1_CASLAT_SHIFT) \ + | (13 << TIMING_CFG1_REFREC_SHIFT) \ + | (3 << TIMING_CFG1_WRREC_SHIFT) \ + | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ + | (2 << TIMING_CFG1_WRTORD_SHIFT)) + /* 0x3937d322 */ +#define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ + | (5 << TIMING_CFG2_CPO_SHIFT) \ + | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ + | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ + | (3 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ + | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ + | (8 << TIMING_CFG2_FOUR_ACT_SHIFT)) + /* 0x02984cc8 */ + +#define CONFIG_SYS_DDR_INTERVAL ((1024 << SDRAM_INTERVAL_REFINT_SHIFT) \ + | (0 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) + /* 0x06090100 */ + +#if defined(CONFIG_DDR_2T_TIMING) +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ + | SDRAM_CFG_SDRAM_TYPE_DDR2 \ + | SDRAM_CFG_32_BE \ + | SDRAM_CFG_2T_EN) + /* 0x43088000 */ +#else +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ + | SDRAM_CFG_SDRAM_TYPE_DDR2) + /* 0x43000000 */ +#endif +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */ +#define CONFIG_SYS_DDR_MODE ((0x0406 << SDRAM_MODE_ESD_SHIFT) \ + | (0x0442 << SDRAM_MODE_SD_SHIFT)) + /* 0x04400442 */ /* DDR400 */ +#define CONFIG_SYS_DDR_MODE2 0x00000000 + +/* + * Memory test + */ +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x0ef70010 + +/* + * The reserved memory + */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT +#else +#undef CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ + +/* + * Initial RAM Base Address Setup + */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) + +#define CONFIG_FSL_ELBC 1 + +/* + * FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ +#define CONFIG_SYS_FLASH_SIZE 8 /* max FLASH size is 32M */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */ + + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ + +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +/* + * NAND Flash on the Local Bus + */ +#define CONFIG_SYS_NAND_BASE 0xE0600000 + + +/* Vitesse 7385 */ + +#define CONFIG_SYS_VSC7385_BASE 0xF0000000 + +/* + * Serial Port + */ +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) + +/* SERDES */ +#define CONFIG_FSL_SERDES +#define CONFIG_FSL_SERDES1 0xe3000 +#define CONFIG_FSL_SERDES2 0xe3100 + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } + +/* + * Config on-board RTC + */ +#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_SYS_PCI_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE +#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000 +#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE +#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000 +#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */ + +#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 +#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 + +#define CONFIG_SYS_PCIE1_BASE 0xA0000000 +#define CONFIG_SYS_PCIE1_CFG_BASE 0xA0000000 +#define CONFIG_SYS_PCIE1_CFG_SIZE 0x08000000 +#define CONFIG_SYS_PCIE1_MEM_BASE 0xA8000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA8000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 +#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xB8000000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 + +#define CONFIG_SYS_PCIE2_BASE 0xC0000000 +#define CONFIG_SYS_PCIE2_CFG_BASE 0xC0000000 +#define CONFIG_SYS_PCIE2_CFG_SIZE 0x08000000 +#define CONFIG_SYS_PCIE2_MEM_BASE 0xC8000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC8000000 +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 +#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xD8000000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 + +#ifdef CONFIG_PCI +#define CONFIG_PCI_INDIRECT_BRIDGE + +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ +#endif /* CONFIG_PCI */ + +/* + * TSEC + */ +#ifdef CONFIG_TSEC_ENET + +#define CONFIG_GMII /* MII PHY management */ + +#define CONFIG_TSEC1 + +#ifdef CONFIG_TSEC1 +#define CONFIG_HAS_ETH0 +#define CONFIG_TSEC1_NAME "TSEC0" +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define TSEC1_PHY_ADDR 2 +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC1_PHYIDX 0 +#endif + +#ifdef CONFIG_TSEC2 +#define CONFIG_HAS_ETH1 +#define CONFIG_TSEC2_NAME "TSEC1" +#define CONFIG_SYS_TSEC2_OFFSET 0x25000 +#define TSEC2_PHY_ADDR 0x1c +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_PHYIDX 0 +#endif + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" + +#endif + +/* + * SATA + */ +#define CONFIG_SYS_SATA_MAX_DEVICE 2 +#define CONFIG_SATA1 +#define CONFIG_SYS_SATA1_OFFSET 0x18000 +#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET) +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA +#define CONFIG_SATA2 +#define CONFIG_SYS_SATA2_OFFSET 0x19000 +#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET) +#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA + +#ifdef CONFIG_FSL_SATA +#define CONFIG_LBA48 +#endif + +/* + * Environment + */ +#ifndef CONFIG_SYS_RAMBOOT + #define CONFIG_ENV_ADDR \ + (CONFIG_SYS_MONITOR_BASE+CONFIG_SYS_MONITOR_LEN) + #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) for env */ + #define CONFIG_ENV_SIZE 0x4000 +#else + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-0x1000) + #define CONFIG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE + +/* + * Command line configuration. + */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC_PIN_MUX +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 256 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_HAS_FSL_DR_USB +#define CONFIG_USB_EHCI_FSL +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET + +#define CONFIG_NETDEV "eth1" + +#define CONFIG_HOSTNAME "mpc837x_rdb" +#define CONFIG_ROOTPATH "/nfsroot" +#define CONFIG_RAMDISKFILE "rootfs.ext2.gz.uboot" +#define CONFIG_BOOTFILE "uImage" + /* U-Boot image on TFTP server */ +#define CONFIG_UBOOTPATH "u-boot.bin" +#define CONFIG_FDTFILE "mpc8379_rdb.dtb" + + /* default location for tftp and bootm */ +#define CONFIG_LOADADDR 800000 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=" CONFIG_NETDEV "\0" \ + "uboot=" CONFIG_UBOOTPATH "\0" \ + "tftpflash=tftp $loadaddr $uboot;" \ + "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ + " +$filesize; " \ + "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ + " +$filesize; " \ + "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ + " $filesize; " \ + "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ + " +$filesize; " \ + "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ + " $filesize\0" \ + "fdtaddr=780000\0" \ + "fdtfile=" CONFIG_FDTFILE "\0" \ + "ramdiskaddr=1000000\0" \ + "ramdiskfile=" CONFIG_RAMDISKFILE "\0" \ + "console=ttyS0\0" \ + "setbootargs=setenv bootargs " \ + "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \ + "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ + "$netdev:off " \ + "root=$rootdev rw console=$console,$baudrate $othbootargs\0" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv rootdev /dev/nfs;" \ + "run setbootargs;" \ + "run setipargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv rootdev /dev/ram;" \ + "run setbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#endif /* __CONFIG_H */ |