diff options
Diffstat (limited to 'include/configs/MPC8544DS.h')
-rw-r--r-- | include/configs/MPC8544DS.h | 422 |
1 files changed, 422 insertions, 0 deletions
diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h new file mode 100644 index 0000000..2cbe855 --- /dev/null +++ b/include/configs/MPC8544DS.h @@ -0,0 +1,422 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2007, 2010-2011 Freescale Semiconductor, Inc. + */ + +/* + * mpc8544ds board configuration file + * + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_PCI1 1 /* PCI controller 1 */ +#define CONFIG_PCIE1 1 /* PCIE controller 1 (slot 1) */ +#define CONFIG_PCIE2 1 /* PCIE controller 2 (slot 2) */ +#define CONFIG_PCIE3 1 /* PCIE controller 3 (ULI bridge) */ +#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ +#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ +#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ + +#define CONFIG_ENV_OVERWRITE +#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ + +#ifndef __ASSEMBLY__ +extern unsigned long get_board_sys_clk(unsigned long dummy); +#endif +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ + +/* + * Only possible on E500 Version 2 or newer cores. + */ +#define CONFIG_ENABLE_36BIT_PHYS 1 + +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 + +#define CONFIG_SYS_CCSRBAR 0xe0000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR + +/* DDR Setup */ +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#define CONFIG_DDR_SPD + +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_VERY_BIG_RAM + +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 2 + +/* I2C addresses of SPD EEPROMs */ +#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ + +/* Make sure required options are set */ +#ifndef CONFIG_SPD_EEPROM +#error ("CONFIG_SPD_EEPROM is required") +#endif + +#undef CONFIG_CLOCKS_IN_MHZ + +/* + * Memory map + * + * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable + * + * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable + * + * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable + * + * 0xe000_0000 0xe00f_ffff CCSR 1M non-cacheable + * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable + * + * Localbus cacheable + * + * 0xf000_0000 0xf3ff_ffff SDRAM 64M Cacheable + * 0xf401_0000 0xf401_3fff L1 for stack 4K Cacheable TLB0 + * + * Localbus non-cacheable + * + * 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M non-cacheable + * 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M non-cacheable + * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M non-cacheable + * + */ + +/* + * Local Bus Definitions + */ +#define CONFIG_SYS_BOOT_BLOCK 0xfc000000 /* boot TLB */ + +#define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */ + +#define CONFIG_SYS_BR0_PRELIM 0xff801001 +#define CONFIG_SYS_BR1_PRELIM 0xfe801001 + +#define CONFIG_SYS_OR0_PRELIM 0xff806e65 +#define CONFIG_SYS_OR1_PRELIM 0xff806e65 + +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} + +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO + +#define CONFIG_SYS_LBC_NONCACHE_BASE 0xf8000000 + +#define CONFIG_SYS_BR2_PRELIM 0xf8201001 /* port size 16bit */ +#define CONFIG_SYS_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/ + +#define CONFIG_SYS_BR3_PRELIM 0xf8100801 /* port size 8bit */ +#define CONFIG_SYS_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ + +#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ +#define PIXIS_BASE 0xf8100000 /* PIXIS registers */ +#define PIXIS_ID 0x0 /* Board ID at offset 0 */ +#define PIXIS_VER 0x1 /* Board version at offset 1 */ +#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ +#define PIXIS_RST 0x4 /* PIXIS Reset Control register */ +#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch + * register */ +#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ +#define PIXIS_VCTL 0x10 /* VELA Control Register */ +#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ +#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ +#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ +#define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */ +#define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */ +#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ +#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ +#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ +#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ +#define PIXIS_VSPEED2 0x1d /* VELA VSpeed 2 */ +#define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ +#define PIXIS_VSPEED2_TSEC1SER 0x2 +#define PIXIS_VSPEED2_TSEC3SER 0x1 +#define PIXIS_VCFGEN1_TSEC1SER 0x20 +#define PIXIS_VCFGEN1_TSEC3SER 0x40 +#define PIXIS_VSPEED2_MASK (PIXIS_VSPEED2_TSEC1SER|PIXIS_VSPEED2_TSEC3SER) +#define PIXIS_VCFGEN1_MASK (PIXIS_VCFGEN1_TSEC1SER|PIXIS_VCFGEN1_TSEC3SER) + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xf4010000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ +#define CONFIG_SYS_PCIE_VIRT 0x80000000 /* 1G PCIE TLB */ +#define CONFIG_SYS_PCIE_PHYS 0x80000000 /* 1G PCIE TLB */ +#define CONFIG_SYS_PCI_VIRT 0xc0000000 /* 512M PCI TLB */ +#define CONFIG_SYS_PCI_PHYS 0xc0000000 /* 512M PCI TLB */ + +#define CONFIG_SYS_PCI1_MEM_VIRT 0xc0000000 +#define CONFIG_SYS_PCI1_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCI1_MEM_PHYS 0xc0000000 +#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCI1_IO_VIRT 0xe1000000 +#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000 +#define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64k */ + +/* controller 2, Slot 1, tgtid 1, Base address 9000 */ +#define CONFIG_SYS_PCIE2_NAME "Slot 1" +#define CONFIG_SYS_PCIE2_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0x80000000 +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xe1010000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xe1010000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ + +/* controller 1, Slot 2,tgtid 2, Base address a000 */ +#define CONFIG_SYS_PCIE1_NAME "Slot 2" +#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xe1020000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xe1020000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +/* controller 3, direct to uli, tgtid 3, Base address b000 */ +#define CONFIG_SYS_PCIE3_NAME "ULI" +#define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xb0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xb0000000 +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x00100000 /* 1M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xb0100000 /* reuse mem LAW */ +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_PHYS 0xb0100000 /* reuse mem LAW */ +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00100000 /* 1M */ +#define CONFIG_SYS_PCIE3_MEM_VIRT2 0xb0200000 +#define CONFIG_SYS_PCIE3_MEM_BUS2 0xb0200000 +#define CONFIG_SYS_PCIE3_MEM_PHYS2 0xb0200000 +#define CONFIG_SYS_PCIE3_MEM_SIZE2 0x00200000 /* 1M */ + +#if defined(CONFIG_PCI) + +/*PCIE video card used*/ +#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT + +/*PCI video card used*/ +/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_VIRT*/ + +/* video */ + +#if defined(CONFIG_VIDEO) +#define CONFIG_BIOSEMU +#define CONFIG_ATI_RADEON_FB +#define CONFIG_VIDEO_LOGO +#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET +#endif + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#ifndef CONFIG_PCI_PNP + #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BUS + #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_IO_BUS + #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */ +#endif + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ + +#ifdef CONFIG_SCSI_AHCI +#define CONFIG_SATA_ULI5288 +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) +#endif /* CONFIG_SCSI_AHCI */ + +#endif /* CONFIG_PCI */ + +#if defined(CONFIG_TSEC_ENET) + +#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define CONFIG_TSEC3 1 +#define CONFIG_TSEC3_NAME "eTSEC3" + +#define CONFIG_PIXIS_SGMII_CMD +#define CONFIG_FSL_SGMII_RISER 1 +#define SGMII_RISER_PHY_OFFSET 0x1c + +#define TSEC1_PHY_ADDR 0 +#define TSEC3_PHY_ADDR 1 + +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +#define TSEC1_PHYIDX 0 +#define TSEC3_PHYIDX 0 + +#define CONFIG_ETHPRIME "eTSEC1" +#endif /* CONFIG_TSEC_ENET */ + +/* + * Environment + */ +#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) */ +#if CONFIG_SYS_MONITOR_BASE > 0xfff80000 +#define CONFIG_ENV_ADDR 0xfff80000 +#else +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#endif +#define CONFIG_ENV_SIZE 0x2000 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE + +/* + * USB + */ + +#ifdef CONFIG_USB_EHCI_HCD +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_PCI_EHCI_DEVICE 0 +#endif + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#endif + +/* + * Environment Configuration + */ + +/* The mac addresses for all ethernet interface */ +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#endif + +#define CONFIG_IPADDR 192.168.1.251 + +#define CONFIG_HOSTNAME "8544ds_unknown" +#define CONFIG_ROOTPATH "/nfs/mpc85xx" +#define CONFIG_BOOTFILE "8544ds/uImage.uboot" +#define CONFIG_UBOOTPATH 8544ds/u-boot.bin /* TFTP server */ + +#define CONFIG_SERVERIP 192.168.1.1 +#define CONFIG_GATEWAYIP 192.168.1.1 +#define CONFIG_NETMASK 255.255.0.0 + +#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/ + +#define CONFIG_EXTRA_ENV_SETTINGS \ +"netdev=eth0\0" \ +"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ +"tftpflash=tftpboot $loadaddr $uboot; " \ + "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ + " +$filesize; " \ + "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ + " +$filesize; " \ + "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ + " $filesize; " \ + "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ + " +$filesize; " \ + "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ + " $filesize\0" \ +"consoledev=ttyS0\0" \ +"ramdiskaddr=2000000\0" \ +"ramdiskfile=8544ds/ramdisk.uboot\0" \ +"fdtaddr=1e00000\0" \ +"fdtfile=8544ds/mpc8544ds.dtb\0" \ +"bdev=sda3\0" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#endif /* __CONFIG_H */ |